USER`S MANUAL
Contents
1. Screws Screws Return the LaundryPure cover to its original Put the two 2 remaining screws along the position fitting the bottom in place and tipping bottom edge and tighten upward eae Secure with two 2 screws not shown along the top edge SYSTEM SET UP Turn the cold water off by shutting off the cold water valve NOTE To help prevent water spray when disconnecting hoses you can relieve pressure in the water line by momentarily starting your washing machine DETAIL1 Important see Detail 1 Below oo D A Remove the cold water hose from the cold water inlet on the back of your washing machine N CAUTION When connecting hoses to your Laundry Pure hand start the hose connector s Using adjustable pliers finish tightening hose connector s Do not remove or disconnect the hot water line from your washing machine or water valve Be sure washers are properly inserted into hose connectors before installing hoses A Remove existing washer from end of cold water hose that was disconnected from washing machine B Install screen included in stainless steel hose package into end of cold water hose that was disconnected from washing machine Failure to install the screen correctly may allow source water sediment to enter the Laundry Pure and cause a clog or flow restriction Never use the hose washer and screen washer Connec2. DESICCANT CARTRIDGE PREPARATION Desiccant Cartridge LaundryPure contains a Desiccant Cartridge containing granules designed to absorb moisture from the air After approximately 300 350 wash cycles the desiccant granules on the right end will turn from blue to pink indicating a need to be replaced Replacement Service Part 9950087 This will keep your LaundryPure operating properly C e Actual lifespan of desiccant granules varies depending upon where the LaundryPure is installed Illustration A CONNECTING POWER N CAUTION Do not use any AC DC adaptor other than the one supplied with your LaundryPure or Vollara replacement AC DC adaptor item US71157 Failure to follow these instructions may void your warranty and or result in damage to your unit fire or electrical shock Insert the provided power cord into the POWER IN socket located on the back of the unit Note Do not plug the adaptor into the wall socket until Position the keyholes of the LaundryPure onto the installation is complete See page 9 screws not shown and finish tightening to secure to the wall The AC DC adaptor is designed to work worldwide The electrical plug may be removed and other types added depending on the country electrical requirements
3. LAUNDRY PURE BETTER FOR YOUR LAUNDRY BETTER FOR YOUR FAMILY BETTER FOR THE ENVIRONMENT PURE ENGINEERED WITH ACTIVEPURE TECHNOLOGY Replace cartridge when desiccant changes USER S MANUAL Le vollara CAUTION Read manual carefully for proper use and operation USE COLDWATER ONLY OUTLET V INLET amp DISCONNECT POWER BEFORE SERVICING Va y vollara GENERAL INFORMATION Contents General Information 2 Use amp Safety Considerations o aoaaa a 3 Installation Requirements 4 Cabinet Features l oaoa oaa a a 4 Before You Start aa aaa aa a 5 Installation s sioe e a bo a e a ee Hoe a a 6 Desiccant Cartridge Preparation 6 System Set Up s s sioa de bee ee eS 8 Before Washing Clothes 10 Using YourLaundryPure 10 To Increase Water Pressure oaoa aaa 11 Maintenance Procedures 12 Frequently Asked Questions 14 Troubleshooting 200 14 Installation Problems 14 Warranty Information 044 15 Declaration of Conformity 16 Please record the serial number of your LaundryPure by Vollara LLC Model Serial Please record the name and phone of your Independent Vollara Business Owner Name Phone SPECIFICATIONS AC DC Adaptor e AC in 100 240V 50 60 Hz 0 8A DC out
4. 12V SS 2 5A Power Consumption e 7 5W standby mode e 25W operating Water Pressure e Minimum 20 psi to 75 psi maximum Water Temperature e Use cold water only do not use hot water Operating Environment e 50 F 100 F 10 C 378 C Humidity 20 70 Dimensions e 18 25 in x 9 375 in x 4 0 in 463 55 mm x 238 13 mm x 101 6 mm Weight e 7 55 pounds e 3 42 kg Typical Dissolved Oxygen Concentration e 0 18 mg L or 0 18 ppm 180 ppb Product Overview LaundryPure is designed to work in conjunction with your washing machine using cold water and ActivePure to clean clothes As your washer begins to fill LaundryPure will turn on LaundryPure is equipped with an internal leak sensor See page 12 for more details USE amp SAFETY CONSIDERATIONS e For indoor use only Do not operate unit with cover removed e Disconnect all power before servicing Do not use an extension cord or other adapter with this appliance e This appliance is not recommended for use with high iron or sediment content water If your water has a high iron or sediment content consult a water filtration expert for available options e Maximum dynamic water inlet pressure is 75psi e Use the included new hose when connecting the LaundryPure unit to your washing machine You should replace any washing machine hose that is more than 2 years old e Do not leave your hot water hose disconnected e Do not clean
5. HEREIN WE MAKE NO REPRESENTATION OR WARRANTY OF ANY KIND ALL OTHER WARRANTIES OF ANY KIND EXPRESS OR IMPLIED ARE HEREBY EXPRESSLY DISCLAIMED INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE LIMITATION OF LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WE SHALL NOT IN ANY CASE BE LIABLE FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM BREACH OF EXPRESSED OR IMPLIED WARRANTIES CONDITIONS GUARANTEES OR REPRESENTATIONS BREACH OF CONTRACT NEGLIGENCE OR ANY OTHER LEGAL THEORY Such excluded damages include but are not limited to loss of profits or revenue and loss of the use of the products and any loss caused by leaks or other water damage EXCLUSION OF SUBSEQUENT OWNERS Except as otherwise required by applicable legislation this warranty is not transferable FOR U S APPLICATION ONLY This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on warranties or on remedies for breach In such states the above limitations may not apply to you FOR CANADIAN APPLICATION ONLY This warranty gives you specific legal rights and you may also have other rights which vary from province to province Some provinces and territories do not allow limitations on warranties or on remedies for breach In such provinces or territories the above limitations may not apply to you If any
6. provision of this warranty or part thereof is held by a court of competent jurisdiction to be invalid illegal or unenforceable the validity legality and enforceability of the remaining provisions or parts thereof will not in any way be affected or impaired within the jurisdiction of that court This entire warranty shall continue to be valid legal and enforceable in any jurisdiction where a similar determination has not been made This warranty is provided by Vollara LLC 5420 LBJ Freeway Suite 1010 Dallas TX 75240 Every effort is made to ensure customers receive an up to date instructions manual on the use of our products however from time to time modifications to our products may without notice make the information contained herein subject to alteration For the latest information please visit our web site 15 CE DECLARATION OF CONFORMITY We Vollara LLC 5420 LBJ Freeway Suite 1010 Dallas TX 75240 Declare under our sole responsibility that the Electronic Purification System Model LaundryPure W1003B to which this declaration relates conforms with the following standards EN55014 1 EMC Requirements for Household Appliances and Similar Apparatus Emissions EN50014 2 EMC Requirements for Household Appliances and Similar Apparatus Immunity EN60950 1 2001 11 2004 Safety of Information Technology Equipment General Requirements By conformance with the standards reference the product meets the provisions of t
7. tighten e Plug the unit into the electrical outlet Illustration D Illustration E Illustration I A Actual lifespan of desiccant granules varies depending upon where the LaundryPure is installed 13 FREQUENTLY ASKED QUESTIONS Does LaundryPure get out tough stains without pretreating Tough stains will still require pretreatment Does the LaundryPure work with all types of water including hard water LaundryPure will work with all household water qualities but the better the incoming water quality the better the results you will have To improve your results if desired use a water softener for hard water and or a prefilter for chlorine sediment or Iron Will the LaundryPure work with Commercial Washing Machines LaundryPure is designed for residential use only Is a Plumber required to install LaundryPure The customer is responsible for installation of their LaundryPure unit Some customers may prefer to have a plumber perform the installation although LaundryPure can be installed in most homes by the home owner using standard hand tools It should be noted there are potential problems which can arise during the installation depending on the condition of the plumbing in the home and the configuration and location of the washer If the cold water valve is stuck or the washing machine needs to be moved back which may require releveling a plumber may be required Vollara LLC is not l
8. warranty service please contact Vollara or your Independent Distributor for the address of the nearest service center LIMITED THREE 3 YEAR WARRANTY Customer should not repackage and ship the LaundryPure unit due to possibility of irreparable damage For warranty service please contact Vollara Customer Service at 800 989 2299 or your Vollara Independent Business Owner for the address of the nearest service center WHAT IS COVERED BY THIS WARRANTY We warrant the LaundryPure to the Customer subject to the conditions below against defects in workmanship or material provided that the products are returned to a service location within three 3 year from the date of purchase INSTALLATION AND MAINTENANCE REQUIREMENTS This warranty is expressly conditioned upon proper installation operation cleaning and maintence all in accordance with the Owner s Manual Failure to meet any of these requirements will void this warranty Servicing of your LaundryPure by parties other than our authorized representatives and or using parts other than genuine parts will also void this warranty HOW TO OBTAIN WARRANTY SERVICE Customer must contact Vollara Customer Service and provide proof of purchase within the above time period We will repair or replace and return the product without charge and within a reasonable period of time subject to the conditions herein if its examination shall disclose any part to be defective in workmans
9. ety messages Safety warnings in this manual are defined as follows N DANGER Death or serious injury can occur if instructions are not followed immediately AN WARNING Electrical shock hazard You can be killed or seriously injured if you don t follow instructions N CAUTION Damage to your appliance or the surrounding area can occur if you don t follow instructions NOTE This information is included to aid in installation and use of this appliance INSTALLATION REQUIREMENTS ELECTRICAL REQUIREMENTS 100 240 Volt 50 60 Hz 5 AMP minimum Fuse or Circuit Breaker LaundryPure is equipped with an AC to DC power supply NEVER USE AN EXTENSION CORD As with most major appliances use of a GFI Ground Fault Circuit Interrupt is not recommended WAT R REQUIREMENTS A dynamic water pressure 20 to 75 psi is required to correctly operate your LaundryPure See Cautions below A CAUTION Incoming water pressure must be less than 75 psi If your household water pressure is greater than 75 psi you must install an inline pressure reducer before installing LaundryPure Failure to follow these instructions may result in water leakage property damage personal injury and may void your warranty Water pressure of 20 to 75 psi is required to correctly operate your LaundryPure Low water pressure may prevent your unit from operating
10. evere eye damage death or electrical shock MAINTENANCE REPLACING THE DESICCANT CARTRIDGE e After approximately 300 350 wash cycles the desiccant granules on the right end will turn from blue to pink indicating a need to be replaced Once the desiccant is pink follow the steps 1 7 to replace the desiccant cartridge for proper operation of the LaundryPure e You will need Replacement Service Part 9950087 Replace spent desiccant cartridge with new cartridge Unplug the unit from the electrical outlet 9950087 Be sure to remove tape and protective caps F Desiccant turns pink in this window Remove Tape amp Cap Remove the cover reference below illustrations B and C Remove Illustration F To reinstall the Desiccant Cartridge reconnect the tubing from the unit into the end of the new cartridge G Illustration G Use new cable ties included in the replacement kit to reattach the cartridge to the LaundryPure H New Cable Tie New Cable Tie Illustration C Cut the cable ties D that hold the Desiccant Cartridge in place and disconnect the plastic tubing E Cable Tie Cable Tie Illustration H Reinstall the cover of the LaundryPure by fitting the bottom in place and tipping upward I Install the two 2 screws on the bottom edge and tighten then reinstall the NSN male 2 two screws in the top and
11. he EU Directives listed below Low Voltage Directive 2006 95 EC applies to power supply only EMC Directive 2004 108 EC RoHS Directive 2002 95 EC WEEE Directive 2002 96 EC Authorized by SSS Company Vollara LLC 5420 LBJ Freeway Suite 1010 Representative Andy Eide Dallas TX 75240 Title Vice President of Product Development and Research U S A Date July 10 2012 FCC DECLARATION OF CONFORMITY _ This equipment has been tested and found to comply with the limits for Industrial Scientific and Medical Equipment Name Vollara LLC ISM pursuant to Part 18 of the FCC Rules These limits are Model LaundryPure W1003B designed to provide reasonable protection against harmful interference in a residential installation This equipment Manufacturer Vollara LLC generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions This device complies with Part 18 of the FCC Rules may cause harmful interference to radio communications However there is no guarantee that interference will not RESPONSIBLE PARTY occur in a particular installation If this equipment does I cause harmful interference to radio or television which can VO aro be determined by turning the equipment off and on the user Vollara LLC is encouraged to try to correct the interference by one or more of the following measures 5420 LBJ Freeway Suite 1010 i Dallas TX 75240 Reorient or reloca
12. he unit as a result of these tests Remove your new LaundryPure from its packaging l Cut open the vacuum seal bag and inspect the unit ge for any signs of shipping damage Remove cover from LaundryPure Remove the two 2 cover screws located on the bottom of the unit Screws Remove the two 2 screws not shown along the top of the LaundryPure LAUNDRY PURE To remove the cover pull the top away from the unit then lift off the cover Ua vollaray INSTALLATION A If using supplied wall anchors drill two 3 16 diameter holes Place two wall anchors into the 16 OC wall Install two supplied screws and tighten until almost all the way in B If mounting to wall studs drill two 3 32 diameter holes approximately 1 deep Install two supplied Io screws and tighten until almost all the way in CAUTION This appliance must be installed in a level Keyholes Level and place the LaundryPure to the wall and mark horizontal configuration as shown Do not where the two 2 keyholes are on each side with a pencil install she Unie vertically below the top of the washer or or at an angle Failure to follow these instructions may prevent the internal moisture NOTE Washing Machine and cold water faucet sensor from operating properly must be within 4 feet of the right side of unit
13. hip or material If we in our discretion are unable to repair the product after a reasonable number of attempts we will provide either a refund of the purchase price or a replacement unit at the company s option WHAT IS NOT COVERED BY THIS WARRANTY This product is intended for household use only Ordinary wear and tear shall not be considered a defect in workmanship or material These warranties do not apply to desiccant cartridge nor for loss or damage caused by accident fire abuse misuse improper installation leaking modification misapplication commercial use or by any repairs other than those provided by our authorized Service Center This warranty is non transferable MISSING SERIAL NUMBERS AND UNAUTHORIZED CHANNELS If a valid serial number is missing from the product the warranty will be voided Vollara products are authorized for sale through Vollara Independent Business Owners only Warranties are voided if a product is purchased through unauthorized channels this includes websites that are not authorized to use Vollara s trademarked names images and logos as well as Internet auction sites e g ebay and Craigslist The only approved Internet presence for Vollara products is www vollara com To confirm SERVICE warranty coverage prior to purchasing a product contact Vollara at 800 989 2299 with the serial number located on the back of the unit EXCLUSION OF OTHER WARRANTIES AND CONDITIONS EXCEPT AS PROVIDED
14. iable for improper installation or damage caused from improper installation and recommend a licensed plumber Appropriate warnings and concerns are included in this owner s manual Always follow local plumbing codes when installing the laundry pure What will need to be replaced on the LaundryPure The desiccant cartridge will need to be replaced after 300 350 wash cycles See Maintenance Replacing the Desiccant cartridge on page 13 Can hook the LaundryPure unit up to things other than a washing machine No However Vollara has an optional water tap you can install on the LaundryPure to create oxygenated water for other cleaning uses see page 12 What effect does LaundryPure have on elastic Normal operation of a LaundryPure unit should have no negative impact on elastic in clothing Can I let my clothes soak It is not recommended that clothes are allowed to soak in LaundryPure water Actual lifespan of desiccant granules varies depending upon where the LaundryPure is installed INSTALLATION PROBLEMS Installation procedures can vary according to washing machine model If you experience installation problems read the manual and watch the installation video to make sure you have installed the unit correctly call Cuustomer Service at 800 989 2299 for more information LIMITED THREE 3 YEAR WARRANTY Customer should not repackage and ship the LaundryPure unit due to possibility of irreparable damage For
15. ional stainless steel hose Part No US70980 not included Connect to HOT water inlet on washing machine 11 TEMPERATURE CONTROLLING WATER VALVES Some washers monitor the incoming cold water temperature and adjust too cold of water by adding hot water even if the water temperature is set to cold If you have one of these washers do not install with the Y adapter Failure to do so may cause the washer to not operate correctly EXTERNAL WATER TAP AVAILABLE SEPARATELY The optional 4G water tap allows you to run oxygenated water for other uses such as cleaning surfaces FAULT INDICATIONS The 4G monitors its operation and if it detects an issue the blue light will change to RED If the 4G detects a leak then the Red light along with an audible alert will sound AN WARNING e Electrical Shock Hazard Disconnect power before If this occurs please contact Customer Service at 800 989 2299 attempting installation or service JX WARNING e Electrical Shock Hazard When working with electrical connections the appliance and surrounding area should be clean and dry of any standing water Failure to follow these instructions can result in death fire or electrical shock N CAUTION e Do not operate LaundryPure with the UV shield or front cover Light in window ill turn bright red removed or improperly installed Failure to follow these instructions can result in s
16. less steel hose US70980 and Cold hose from your washer to the Y adaptor see diagram below Operate your washer on the WARM WARM setting your LaundryPure will still be LAUNDRY PURE using just cold water N CAUTION When connecting hoses to your Connect the Y adaptor to the OUTLET on your LaundryPure Be sure to hold the fitting with pliers while tightening the Laundry Pure hand start the hose connector s Using adjustable pliers finish tightening hose connector s adaptor Disconnect this NOTE Your Hot source water valve stainless steelhose will not have a hose connected to Kose tromithe OUTLET on your LaundryPure it Make sure it is fully turned off It is recommended you secure a cap available at most home iheiiconnect it to the Y adaptor improvement stores to prevent leakage with LaundryPure Connect to COLD water inlet on washing machine N CAUTION Turn off both water valves hot and cold before disconnecting hoses Failure to follow these instructions may result in water leakage and or possible injury from hot water Stainless steel hose supplied Connect to household plumbing COLD water valve Y adaptor Make sure the Y adaptor valve is in the on position Disconnect the existing hose from the HOT valve and washing machine and remove Replace with opt
17. n as water begins to flow when looking through the view window NOTE Your LaundryPure will automatically turn on and off as your washing machine starts and stops BEFORE WASHING CLOTHES RST TIME BEFORE USING YOUR LAUNDRYPURE FOR THE F IF YOUR WASHING MACHINE IS NEW skip this section and continue below LAUNDRY PURE Zz IF YOUR WASHING MACHINE IS NOT NEW you will need to perform this procedure to help remove any detergent buildup that may contaminate your clothing 1 Do not put clothes in the washer at this time Set your machine to its largest load setting cold water only 2 Start the washer and let it run through every cycle 3 Once it has finished repeat Steps 1 and 2 three more times Depending on the age and severity of detergent buildup it may be necessary to perform Step 3 several times N CAUTION To avoid the possibility of water damage should a hose leak always have faucets accessible and turn off faucets when washer is not in use NOTE If you have a front loading washer odors can develop due to stagnant water left inside If musty odors develop it may be necessary to run a commercially available cleaner made especially for front loading washers to eliminate such odors USING YOUR LAUNDRYPURE coup wor NORMAL OPERATION Using your LaundryPure is as simple as turning on the washing machine Laundr
18. properly and or cause a failure in your washing machine s water valve The washer s water valve may also not shut off completely Check the documentation supplied with your washing machine for exact CABINET FEATURES LOCATION CONSIDERATIONS It is recommended the LaundryPure never be installed in areas where water may freeze since the unit will always maintain some water in the unit the water valve and hose areas This can cause damage to internal components It is also recommended to avoid installation in areas of high humidity as it can effect the operation of the unit specifications Your washing machine and cold water faucet must be within 4 feet of the right side of the unit to use the inlet hose provided with your LaundryPure TO AVOID THE POSSIBILITY OF WATER DAMAGE SHOULD A HOSE LEAK ALWAYS HAVE FAUCETS ACCESSIBLE AND TURN OFF FAUCETS WHEN WASHER IS NOT IN USE Water quality may affect the performance of your LaundryPure unit If you have water quality concerns such as high iron content or high chlorine content consult a water filtration expert This system is designed for use on potable water systems only LAUNDRY 9 375 238 13 rm 4 0 101mm WINDOW LAUNDRY ZZ vollara WATER OUTLET WATER INLET BEFORE YOU START NOTE Your Laundry Pure Unit was factory tested It is normal for some residual water to still remain in t
19. t the hose from the cold water inlet on your washing machine to the INLET connection on your LaundryPure Connect the new hose provided with your LaundryPure to the water OUTLET connector on your LaundryPure unit Finally connect the new hose to the cold water inlet on your washing machine LAUNDRY PURE Hold with pliers while installing hose in order to prevent fitting from rotating EN LAUNDRY PURE while installing hose in order to prevent fitting from rotating Hold with pliers Fe LAUNDRY PURE es E I T SYSTEM SET UP LAUNDRY Plug power cord into the wall outlet of your home s electrical power system See page 4 for electrical requirements Static Mixer LAUNDRY PURE Turn on the cold water valve is leaking Tighten if necessary Check all hoses to ensure no water AN WARNING Electrical Shock Hazard When working with electrical connections the appliance and surrounding area should be clean and dry of any standing water Failure to follow these instructions can result in death fire or electrical shock AN WARNING Electrical Shock Hazard Do no use an extension cord Failure to follow these instructions can result in death fire or electrical shock O Start your washer The static mixer light warm blue glow should come o
20. te the receiving antenna Ph 800 989 2299 Increase the separation between the equipment and receiver Signature cece eh AN Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Printed Name Andy Eide Title Vice President Product Development amp Research Date July 10 2012 Consult the Dealer or an experienced radio TV technician for help KE vollara Vollara LLC 5420 LBJ Freeway Suite 1010 Dallas TX 75240 800 989 2299 Part No 65 00427 VA 00273 Vollara LLC All Rights Reserved LP_OM_65 00427_VA 00273_1_12
21. yPure is designed to use the COLD COLD setting of your washing machine DETERGENT AND FABRIC SOFTENER You may choose to continue to use detergent and or fabric softeners if desired However to completely experience all the benefits of your new LaundryPure we recommend washing using nothing but cold water NEVER apply detergent directly to dry cloths Allow washer to fill then add detergent to prevent staining on cloths HEAVY STAINS For heavy stains pre treat area apply pre treater such as Re Move rub gently and let stand for several minutes Wash as normal FOR WASHERS THAT REQUIRE HOT amp COLD WATER INPUT Some washing machine models require water to flow through both the HOT and COLD valves for proper operation In some cases if only the COLD water side is connected the water valve will not operate or the washing machine will not fill to the proper level To solve this problem the installation of a Y adaptor available at most hardware stores may be used The use of the Y adaptor allows water to flow equally through both the HOT and COLD water valves Optional stainless steel hose US70980 must be installed on the hot water connection To Install turn water off at the valves and disconnect the existing HOT water hose at the valve and washing machine Connect the Y adaptor to the Outlet on your LaundryPure then connect both the optional stain
22. your LaundryPure with harsh chemicals abrasives or cleansers Use a soft cloth dampened with water e Do not mount the LaundryPure unit vertically below the top of the washer or or at an angle Improper mounting may not allow the unit to function properly and void your warranty See page 5 for correct mounting instructions e LaundryPure is designed for normal residential use only Use in a commercial or non residential setting will void your warranty N CAUTION Water treated by your LaundryPure unit is intended for clothes washing only and is NOT approved for any internal consumption such as drinking bathing brushing teeth etc DO NOT drink ingest or internally consume the water from your LaundryPure unit or washing machine DO NOT provide water from your LaundryPure to your pets or other animals IMPORTANT SAFETY PRECAUTIONS e To prevent unnecessary risk of fire electrical shock or personal injury all wiring must be done in accordance with the National Electrical Code ANSI FNPA No 70 Latest Revision and local codes and ordinances It is the personal responsibility and obligation of the appliance owner to provide adequate electrical service for this appliance NOTE Your LaundryPure Unit was factory tested It is normal for some residual water to still remain in the unit as a result of these tests We have provided important safety warnings in this manual and on your appliance Always read and obey all saf
Download Pdf Manuals
Related Search