9113 mk5a MANUAL R1.p65
Contents
1. Press the MEM key to enter MEMORY mode e The sequence for dialing out a speed dial number in memory is ON MEM Number Button 0 9 e Press MEM PROG to enter programming mode See Programming Speed Dial Numbers for more details TONE KEY e In PULSE dialing mode this key is used to switch to Temporary TONE dialing mode BASE UNIT FEATURES IN USE CHARGING LED The LED illuminates steadily when the Handset is in the Base cradle to indicate that the Handset battery is being charged The LED illuminates whenever the Handset is being used e This LED also flashes with the cadence of the incoming ring PAGE KEY e Press the PAGE key to page the Handset Press it second time to cancel a page The Base will ring the Handset for 1 minute before ending the page automatically e The Handset can also cancel the page by pressing the OFF key 5 OPERATING INSTRUCTIONS Making Calls Pick up the Handset and press ON When you hear a dial tone dial the number The ON LED will illuminate while the Handset is in use If you make a mistake when dialing press OFF to hang up then press ON to get the dial tone again You must always press ON before you can dial a call on the Handset Answering Calls When an incoming call is ringing the IN USE LED on the Base and ON LED on the Handset will flash To answer a call when the Handset is in the Base just pick up the Handset To answer a call when the Handset is away from t2. handset outdoors in the rain or handle it with wet hands Do not install your base unit near a sink bathtub or shower Remember that electrical appliances can cause serious injury if used when you are wet or standing in water If your base unit should fall into water DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL Then pull the unit out by the unplugged cords Electrical Storms Electrical storms can sometimes cause power surges harmful to electronic equipment For your own safety use caution when using electric appliances during storms Cleaning your telephone Your telephone has a durable plastic casing that should retain its luster for many years Clean it only with a soft cloth slightly dampened with water or a mild soap Do not use excess water or cleaning solvents of any kind TECHNICAL SPECIFICATIONS FREQUENCY CONTROL Crystal Controlled Dual PLL Synthesizer TRANSMIT FREQUENCY Handset 923 40MHz to 927 75MHz Base 902 40MHz to907 05MHz RECEIVE FREQUENCY Handset 902 40MHz to907 05MHz Base 923 40MHz to 927 75MHz NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC and IC Actual operating range may vary according to environmental conditions at the time of use SIZE Handset 17 5cm x 5 5cm x 3 9cm Base 19 3cm x 14 8cm x 5 4cm L x WEIGHT Handset 146 grams Base 283 grams POWER REQUIREMENTS Handset Self contained nickel cadmium rechargeable battery supply 3 6V nominal
3. provided with this product It is designed to be connected to a compatible modular jack that is also compliant An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines See Installation Instructions in the users manual This equipment may not be used with Coin Telephone Lines or with Party Lines If you have specially wired alarm dialing equipment connected to your telephone line ensure the connection of this equipment does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer 3 Repair instructions If this equipment is malfunctioning it must be unplugged from the modular jack until the problem has been corrected Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents For repair procedures follow the instructions outlined under the Limited Warranty 4 Rights of the telephone company If this equipment is causing harm to the telephone network the telephone company may temporarily discontinue your telephone service The telephone company is required to notify you before interrupting service If advance notice is not practical you will be notified as soon as possible You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC Your telephone company may make changes in
4. reduce the risk of fire or injury read and follow these instructions 1 2 3 4 Use only VTECH battery pack supplied or equivalent Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause burns Do not dispose of the battery in a fire The cell may explode The RBRC Seal The RBRC Seal on the nickel cadmium battery indicates that VTech Communications Inc is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives when taken out of service within the United States and Canada The RBRC program provides a convenient alternative to placing used nickel cadmium batteries into the trash or municipal waste which may be illegal in your area VTech s participation with RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers Please call 1 800 8 BATTERY for information on Ni Cd battery recycling and disposal bans restrictions in your area VTech s involvement in this program is part of its commitment to protecting our environment and conserving natural resources RBRC is a registered
5. the product There are no other express warranties No one is authorized to make modifications to this limited warranty and you should not rely on any such modification State Law Rights This warranty gives you specific legal rights and you may also have other rights which vary from state to state Limitations Implied warranties including those of fitness for a particular purpose and merchantability an unwritten warranty that the product is fit for ordinary use are limited to one year from date of purchase Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you In no event shall VTECH be liable for any indirect special incidental consequential or similar damages including but not limited to lost profits or revenue inability to use the product or other associated equipment the cost of substitute equipment and claims by third parties resulting from the use of this product Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you 11 MAINTENANCE Your VT 9113 cordless telephone contains sophisticated electronic parts so it must be treated with care Avoid rough treatment Place the handset down gently Save the original packing materials to protect your telephone if you ever need to ship it Avoid Water Your telephone can be damaged if it gets wet Do not use the
6. tones and to turn off a ringer on the Handset To program the Handset must be OFF To select a different ringer type do the following e Press MEM PROG e Press the key e Press a key 1 2 3 or 4 to select a ringer type e Press the MEM key to confirm Turning Off The Ringer To turn off the ringer on the Handset do the following Press MEM PROG e Press the key Press 5 to turn off the ringer e Press the MEM key to confirm To turn the ringer on again see Programming the Ringer Type Checking The Ringer To check the ringer which is currently programmed do the following 6 OPERATING INSTRUCTIONS Press MEM PROG Press the key Press 0 Press the MEM key to confirm Memory Dialing The VT9113 can store up to 10 different phone numbers that you can dial just by pressing ON MEM and one of the number keys 0 9 Note if the dialing method is pulse the digit lt gt will be ignored and the digit lt gt will initial temporary DTMF dialing Programming Speed Dial Numbers The Handset must be OFF 1 Press MEM PROG The ON LED will blink to indicate that you are in the programming mode 2 Press the number of the memory location you wish to store the number in 0 9 3 Using the dial pad dial the number you want to store The number can be up to 16 digits long The number can be entered manually or by using REDIAL 4 Press MEM to store the phone number to the key you selected The phone now e
7. 300mAh capacity Power Adapter 6V AC 220mA SPECIFICATIONS ARE TYPICAL AND MAY CHANGE WITHOUT NOTICE 12 L x W xT maximum antenna excluded X X W x T maximum antenna excluded FCC ACTA and IC REGULATIONS This equipment complies with Parts 15 of the Federal Communications Commission FCC rules for the United States It also complies with regulations RSS210 and CS 03 of Industry and Science Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device A label is located on the underside of the Base Unit containing either the FCC registration number and Ringer Equivalence Number REN or the IC registration number and Load Number You must upon request provide this information to your local telephone company This equipment is compatible with inductively coupled hearing aids Should you experience trouble with this telephone equipment please contact VTech Communications Inc CUSTOMER SERVICE at 1 800 595 9511 In Canada call VTech Electronics Ltd at 1 800 267 7377 For repair warranty information The telephone company may ask you to disconnect this equipment from the line network until the problem has been corrected FCC Part 15 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
8. Council for Terminal Attachments ACTA We are required to provide you with the following information 1 Product identifier and REN information The label on the back or bottom of this equipment contains among other things an identifier indicating product approval and the Ringer Equivalence Number REN This information must be provided to your local telephone company upon request For 13 FCC ACTA and IC REGULATIONS equipment approved prior to July 23 2001 the product identifier is preceded by the phrase FCC Reg No and the REN is listed separately For equipment approved after that date the product identifier is preceded by US and a colon and the REN is encoded in the product identifier without a decimal point as the sixth and seventh characters following the colon For example the product identifier US AAAEQ03T123XYZ would indicate an REN of 0 3 The REN is used to determine how many devices you may connect to your telephone line and still have them ring when you are called In most but not all areas the sum of all RENs should be five 5 0 or less You may want to contact your local telephone company for more information 2 Connection and use with the nationwide telephone network The plug and jack used to connect this equipment to the premises wiring and the telephone network must comply with the applicable Part 68 rules and technical requirements adopted by ACTA A compliant telephone cord and modular plug is
9. INTRODUCTION Parts Check List 1 Handset To purchase replacement battery packs 2 Base Unit call VTECH Communications at 1 800 595 3 Telephone Line Cord 9511 In Canada call VTECH Electronics 4 Battery Pack at 1 800 267 7377 5 AC Adapter TELEPHONE CORD BATTERY PACK AC ADAPTER IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to ls 2 3 10 1 1 N 13 14 reduce the risk of fire electric shock and injury including the following Read and understand all instructions Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water for example near a bath tub kitchen sink or swimming pool Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings in the cabinet and the back or bottom are provided for ventilation To protect it from overheating these openings must not be blocked by placing the product on the bed sofa rug or other similar surface This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation where proper ventilation is not provided T
10. WHEN YOU RE NEAR THE BASE UNIT Household appliances plugged into the same circuit as the Base Unit can sometimes cause interference Try moving the appliance or the Base Unit to another outlet YOU GET NOISE STATIC OR A WEAK SIGNAL WHEN YOU RE AWAY FROM THE BASE UNIT You may be out of range Either move closer to the Base or relocate the Base Unit The layout of your home may be limiting the range Try moving the Base Unit to the second or third floor or to some other location THE HANDSET DOES NOT RING WHEN YOU RECEIVE A CALL Ensure that the ringer is turned on Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone jack Make sure the power cord is plugged in You may be too far from the Base Unit You may have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of the other phones YOUR CALLER FADES IN AND OUT You may be nearly out of range Move closer or relocate the Base YOU HEAR OTHER CALLS WHILE USING YOUR PHONE e Replace the Handset in the Base cradle wait a few moments and try again Disconnect your Base Unit from the telephone jack and plug in a regular telephone If you still hear other calls the problem is probably in your wiring or local service Call your local telephone company IN CASE OF DIFFICULTY YOU HEAR NOISE IN THE HANDSET AND NONE OF THE KEYS OR BUTTONS WORK Make sure the power cord
11. ain To end the page at the Handset press OFF If the Handset is in use off hock when PAGE is pressed on the Base Unit the Handset will emit one page alert If the Handset is not in use on hook the page alert will continue for approximately 60 seconds This feature is useful in locating a misplaced Handset PRR 7 IN CASE OF DIFFICULTY If you have difficulty operating your phone the suggestions below should solve the problem If you still have difficulty after trying these suggestions In the US Call VTECH Communications at 1 800 595 9511 In Canada Call VTECH Electronics at 1 800 267 7377 THE PHONE DOESN T WORK AT ALL Make sure the power cord is plugged in Make sure the telephone line cord is plugged firmly into the Base Unit and the telephone wall jack Make sure the batteries are properly charged If the Handset makes two beeps the batteries need charging If the IN USE LED on the Base and ON LED on the Handset do not light when you press ON you must charge the batteries e If you recently installed a new battery pack make sure it is installed correctly NO DIAL TONE e First check all the suggestions above e If you still don t hear a dial tone disconnect the Base Unit from the telephone jack and connect a different phone If there is no dial tone on that phone either the problem is in your wiring or local service Call your local telephone company YOU GET NOISE STATIC OR A WEAK SIGNAL EVEN
12. ay result in damage and will often require extensive work to restore the product to normal operation e If the product has been dropped and the cabinet has been damaged f If the product exhibits a distinct change in performance Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak SAVE THESE INSTRUCTIONS INSTALLING REPLACING THE BATTERY PACK os With the red and black wires at the bottom Slide the battery cover off by gently pressing on the recessed area with a downward motion Unplug and remove the old battery pack Don t put the old battery pack in a trash compactor or a fire it could burst of the pack angle the top of the battery into the compartment under the two claws Next press the lower end of the battery pack down so it is held in place by the lower claw Now plug the connector into the socket located below the battery Slip the battery wires into the wire guide located below and to the left of the socket Replace the battery cover by sliding it into place The new battery pack must be charged before using your telephone Place the handset in the cradle of the base unit to allow it to charge for 16 hours Maximum battery life between charges is more than 3 75 hours of continuous talk time or 3 75 days of standby CAUTION To
13. ber of devices you may connect to the telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subjected only to the requirement that the sum of the REN does not exceed five 5 0 Notice The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of services in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural a
14. defects in materials and workmanship during the limited warranty period Materially Defective Product During the limited warranty period VTECH s authorized service representative will repair or replace at VTECH s option without charge a Materially Defective Product If we repair this product we may use new or refurbished replacement parts If we choose to replace this product we may replace it with a new or refurbished product of the same or similar design VTECH will return repaired or replacement products to you in working condition VTECH will retain defective parts modules or equipment Repair or replacement of Product at VTECH s option is your exclusive remedy You should expect the repair or replacement to take approximately 30 days How long is the limited warranty period The limited warranty period for the product extends for ONE 1 YEAR from the date of purchase if we repair or replace a Materially Defective Product under the terms of this limited warranty This limited warranty also applies to repaired or replacement Products for a period of either a 90 days from the date the repaired or replacement Product is shipped to you or b the time remaining on the original one year warranty whichever is longer What is not covered by this limited warranty This limited warranty does not cover 1 ON Product that has been subjected to misuse accident shipping or other physical damage improper installation abn
15. he Base just press any key on the Handset except OFF This is very useful in a dark environment you do not have to fumble around looking for the ON key to answer the call Disconnecting To end a call either place the Handset back in the Base or press OFF on the Handset Changing Channels If you notice interference when using your Handset press CHAN to switch to a clear channel This function is only available when you are on a call TONE PULSE Setting If you have touch tone service on phone line Press MEM PROG MEM to switch to TONE dialing If you have rotary service press MEM PROG MEM to switch to PULSE NOTE Your VT9113 is preset at the factory for TONE dialing Temporary Tone If you have a rotary dial pulse telephone service TONE PULSE setting is set to PULSE this feature allows you to enter special codes and tones to operate answering machines use electronic banking services calling cards or other special services First dial the call normally Then activate the Temporary Tone feature by pressing TONE the key You can then press the numbers or symbols you need and your phone will send the proper signals To end the call press OFF or place the Handset back in the Base The phone will automatically go back to rotary dial pulse service Programming The Ringer Type The Handset ringer is capable of four different types of ringing tones The following sections detail how to change the different
16. his product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your dealer or local power company Do not allow anything to rest on the power cord Do not locate this product where the cord will be abused by persons walking on it Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product To reduce the risk of electric shock do not disassemble this product If service or repair work is required contact VTech Customer Service at 1 800 595 9511 Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks Incorrect reassembling can cause electric shock when the appliance is subsequently used Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock Unplug this product from the wall outlet a When the power supply cord or plug is damaged or frayed b If liquid has been spilled into the product c If the product has been exposed to rain or water d If the product does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls m
17. is plugged in e Your Base Unit and Handset may not be operating on the same channel or security code Place the Handset in the cradle for a few moments to reload the security code and reset the channel COMMON CURE FOR ELECTRONIC EQUIPMENT Electronics like people can sometimes get confused If the unit does not seem to be responding normally then try putting the Handset in the cradle to re initialize the unit If it still does not seem to respond perform the following steps in the order listed Disconnect the power to the Base Disconnect the Handset battery pack Wait a few minutes Connect power to the Base Reconnect the Handset battery Place the Handset in the Base Unit cradle If the Handset has not been recently charged allow 8 hours before use P OURAN WARRANTY STATEMENT What does this limited warranty cover The manufacturer of this VTECH product VTECH Communications warrants to the holder of a valid proof of purchase Consumer or you that the product and all accessories provided by VTECH in the sales package Product are free from material defects in material and workmanship pursuant to the following terms and conditions when installed and used normally and in accordance with operation instructions This limited warranty extends only to the Consumer for Products purchased and used in the United States of America What will VTECH Communications do if the Product is not free from material
18. its facilities equipment operation or procedures that could affect the proper functioning of this product The telephone company is required to notify you if such changes are planned 5 Hearing aid compatibility If this product is equipped with a corded or cordless handset it is hearing aid compatible 6 Programming testing of emergency numbers If this product has memory dialing locations you may choose to store police fire department and emergency medical service telephone numbers in these locations If you do please keep three things in mind a We recommend that you also write the telephone number on the directory card so that you can still dial the emergency number manually if the memory dialing feature doesn t work b This feature is provided only as a convenience and the manufacturer assumes no responsibility for customer reliance upon the memory feature c Testing the emergency telephone numbers you have stored is not recommended However if you do make a call to an emergency number e You must remain on the line and briefly explain the reason for the call before hanging up 14 FCC ACTA and IC REGULATIONS e Programming testing of emergency numbers should be performed during off peak hours such as in the early morning or late evening when the emergency services tend to be less busy IC Industry Canada This telephone is registered for use in Canada Notice The REN assigned to this device denotes the num
19. ormal operation or handling neglect inundation fire water or other liquid intrusion or Product that has been damaged due to repair alteration or modification by anyone other than an authorized service representative of VTECH or Product to the extent that the problem experienced is caused by signal conditions network reliability or cable or antenna systems or Product to the extent that the problem is caused by use with non VTECH electrical accessories or Product whose warranty quality stickers Product serial numbers plates or electronic serial numbers have been removed altered or rendered illegible or Product purchased used serviced or shipped for repair from outside the United States or used for commercial or institutional purposes including but not limited to Products used for rental purposes or Product returned without valid proof of purchase see 2 below or Charges for installation or set up adjustment of customer controls and installation or repair of systems outside the unit How do you get warranty service To obtain warranty service in the United States of America call 1 800 595 9511 for instructions regarding where to return the Product Before calling for service please check the users manual A check of the Product controls and features may save you a service call WARRANTY STATEMENT Except as provided by applicable law you assume the risk of loss or damage during transit and transportation and are
20. reas Caution Users should not attempt to make such connections themselves but should contact the appropriate electrical inspection authority or electrician as appropriate Your VT9113 is designed to operate at the maximum power allowed by the FCC and IC This means your Handset and Base Unit can communicate only over a certain distance which will depend on the location of the Base Unit and Handset weather and the construction and layout of your home or office 15 ANY KEY ANSWER 30 CHANNEL OPERATION UNIQUE STAND UP DESIGN vtech VTECH TELECOMMUNICATIONS LTD www vtechphones com Printed in China 91 5627 10 00 ISSUED 0
21. responsible for delivery or handling charges incurred in the transport of Product s to the service location VTECH will return repaired or replaced product under this limited warranty to you transportation delivery or handling charges prepaid VTECH assumes no risk for damage or loss of the Product in transit If the Product failure is not covered by this limited warranty or proof of purchase does not meet the terms of this limited warranty VTECH will notify you and will request that you authorize the cost of repair prior to any further repair activity You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty What must you return with the Product to get warranty service 1 2 Return the entire original package and contents including the Product to the VTECH service location along with a description of the malfunction or difficulty Include valid proof of purchase sales receipt identifying the Product purchased Product model and the date of purchase or receipt and 3 Provide your name complete and correct mailing address and telephone number Other Limitations This warranty is the complete and exclusive agreement between you and VTECH It supersedes all other written or oral communications related to this Product VTECH provides no other warranties for this product The warranty exclusively describes all of VTECH s responsibilities regarding
22. s or terminals unless the telephone line has been disconnected at the network interface 4 Use caution when installing or modifying telephone lines HANDSET FEATURES ON LED The ON LED lights when the Handset is on an active call It flashes in cadence with an incoming ring e It flashes quickly during Programming mode It flashes slowly when the battery pack is low ON FLASH KEY e Press the ON key to make a call e If you are currently on a call and you hear a call waiting tone press ON to switch to the second call Press ON again to return to the original call VOLUME CONTROL Adjust the volume of what you hear through the Handset While on a call press the or key to adjust the listening volume The Handset will emit a double beep when the maximum or minimum volume level has been reached OFF KEY e Press the OFF key to exit all modes of operation REDIAL PAUSE KEY When you hear the dial tone press REDIAL to call the last number dialed on your phone It can also be used to store the last number dialed into the speed dial memory See Storing a Redial Number into Speed Dial for details e You can store pauses into your speed dial numbers See Storing Pauses in Memory for details CHAN KEY e Pressing the CHAN key when the Handset is in use will activate a channel change to the next free channel e This is used if you are experiencing noise or interference on the current channel MEM PROG KEY
23. the user s authority to operate the equipment The equipment has been tested and found to comply with part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet or on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Part 68 and ACTA If this equipment was approved for connection to the telephone network prior to July 23 2001 it complies with Part 68 of the Federal Communications Commission FCC rules If the equipment was approved after that date it complies with the Part 68 rules and with Technical Requirements for Connection of Equipment to the Telephone Network adopted by the Administrative
24. trademark of Rechargeable Battery Recycling Corporation GETTING STARTED Setting Up Your VT9113 1 Choose an area near an electrical outlet and a telephone wall jack 2 Plug the AC power adapter into an electrical outlet and the DC connector to the power jack on the bottom of the Base Unit Insert the cord in the channel guide CAUTION Use only the AC adapter shipped with your VT9113 It is specifically designed for this product NOTE Connect power to the Base Unit before placing the handset in the cradle 3 CHARGE THE HANDSET BATTERY PACK BEFORE USE The batteries recharge automatically whenever the Handset is in the Base Unit cradle The batteries must be charged for 16 hours before using your phone for the first time 4 Connect the telephone line cord Insert one end of the telephone line cord into the phone jack on the bottom of the Base Unit Plug the other end into a telephone wall jack Make sure the plugs snap securely into place Insert the cord in the channel guide 5 CHECK FOR A DIAL TONE After the battery pack is charged pick up the Handset and press the ON key The IN USE LED on the Base and ON LED on the Handset should light up and you should hear a dial tone If not see IN CASE OF DIFFICULTY CAUTION 1 Never install telephone wiring during a lightning storm 2 Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations 3 Never touch uninsulated telephone wire
25. xits programming mode and emits a happy tone Speed Number Dialing 1 Press ON to get a dial tone 2 Press MEM and the memory location number key 0 9 For example to dial the number you assigned to key 8 you would press ON MEM 8 To Change or Replace a Speed Dial Number To change or replace a stored number in speed dial memory simply enter the new number and store it in the memory location you wish to change For example to change the number stored in memory position 7 to 555 1111 you would press MEM PROG 7 555 1111 MEM Storing Pauses in Memory To insert a pause in a phone number press REDIAL PAUSE The pause is 2 seconds in length For longer pauses press REDIAL PAUSE two or more times Each additional press indicates an additional 2 second pause If your phone is connected to a PBX you can store the PBX access number and a pause before the phone number For example to store 9 PAUSE 555 1234 in memory location 8 do the following Press MEM PROG Press 8 Press 9 Press REDIAL PAUSE Dial 555 1234 Press MEM Using REDIAL To redial the last number you called press ON then press REDIAL The phone will automatically dial the number Storing a Redial Number into Speed Dial To store the last number you dialed as a Speed Dial number press MEM PROG a location number 0 9 REDIAL MEM The Page Feature From the Base Unit press PAGE to signal the person at the Handset To end the page at the base press PAGE ag
Download Pdf Manuals
Related Search