Home

User Guide - GarrettCom

1. GarrettCom Inc 47823 Westinghouse Dr Fremont CA 94539 7437 Phone 510 438 9071 Fax 510 438 9072 Website http www GarrettCom com email support garrettcom com Federal Communications Commission Radio Frequency Interference Statement This equipment generates uses and can radiate frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Canadian Emission This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil respecte toutes les exigences du R glement sur le mat riel du Canada Cet appareil est Classe A 11 Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 UL Safety Statements Electrical Safety requirements See pg 64 Sec B4 1 for additional information 1 This product is to be installed Only in Restricted Access Area
2. f the equipment is mounted in an enclosed or multiple rack assembly verify the equipment s power requirements to prevent overloading of the building s electrical circuits 5 If the equipment is mounted in an enclosed or multiple rack assembly verify that the equipment has a reliable and uncompromised earthing path This section describes installation of the Magnum 6K 16 Series Switches as well as connection of the various Ethernet media types 3 1 Locating Magnum 6K16 Series Switches For vertical panel mounting and wall mounting see Section 3 4 For vertical DIN Rail mounting see Section 3 3 For DC power options see Appendix B For Dual Source see Appendix C For AC power input locate an AC receptacle that is within six feet 2 meters of the intended Magnum 6K 16 Series site The rugged metal case of the Magnum 6K16 Series will normally protect it from accidental damage in a lab or workplace setting Maintain an open view of the front to visually monitor the status LEDs Keep an open area around the unit so that cooling can occur from convection while the unit is in operation The 6K 16 Series has no fans so it is silent when in operation Internal electronics use the case as a heat sink so the unit may normally be quite warm to the touch 3 2 Connecting Ethernet Media The Magnum 6K16 Series Switches are specifically designed to support all standard Ethernet media types within a single Switch unit This is
3. FULL HALF Series Switch it supports the _ www GarrettCom com ss 53 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 standard distances as mentioned on 5 2 3 and the LEDs also act similarly 5 2 7 6KP8 MLC 8 ports 100Mbps multi mode LC connector Small Form Factor 8 Port 100Mbps multi mode LC fiber port Magnum 6KP8 MLC is a eight port multi mode fiber LC connector small form factor used primarily in 100Mbps fiber to the desktop links When installed in a Magnum 6K 16 Series k o Kk D K D me Switch it supports fiber optic cable ACTIVIT FULI BAL distances up to the IEEE standard 100Mbps distance limits i e typically 2km at full duplex and 412m at half duplex The compact size of the LC Connector reduces the size of wiring panels in wiring closets while providing the advantage of future proof fiber optic technology The cable end is a plug in connector with both fiber strands terminated in one housing that cannot be improperly inserted Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off 5 2 8 6KP8 45LC Combo 4 100Mbps multi mode LC small form factor and 4 10 100 4 Port 10 100Mbps amp 4 port 100Mbps p P p Mbps RJ 45 Connector Multi Mod LC On The Magnum 6
4. MNS 6K the 6K 16V switch can be easily managed and monitored Dual LEDs on the front and the connector side help the vertically mounted 6K 16V to be monitored easily The modular designed Magnum 6K16V managed fiber switch can support of maximum four Gigabit modules fiber or copper to meet any demand of bandwidth required applications In a on going demand of diversified designed Ethernet application the Magnum 6K16V is a finest solution to meet and satisfy those requirement by the rich modular structure The Relay contacts for external ALARM is another additional feature which allows the Magnum 6K16V to monitor the internal power failure and controlled via hardware or software trap control 2 2 1b Magnum 6K16 Managed Carrier Class Switch The rack mountable 6K 16 model of 6K16 Series family is a modular managed Carrier class Switch which can be mounted horizontally as rack mount shown in the picture Specially designed to cater the requirements for carrier class Telco applications or factory floor and office purpose solutions the Magnum 6K16 can be mount side by side ona 19 rack mount tray to provide the needs of port density Equipped with three fan at the rear the fan cooled Magnum 6K16 through its modular designed and diversified support of 10 100 or 1000Mb speed can be a excellent gear for the carrier class and 11 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 factory floor applicat
5. 100 ports twol100 Mb 2km mm FX MTRJ connectors P6KP8 452SLC 6 2 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 15km Sm FX LC connectors P6KP6 RJMST 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX ST connectors P6KP6 RJMSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 2km mm FX SC connectors P6KP6 RJSSC 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 20km sm FX SC connectors P6KP6 RJSSCL 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 100 Mb 40km sm FX SC connectors P6KP6 RJ10ST 4 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two 10 Mb 2km sm FL ST connectors LT GarrettCom Inc reserves the right to change specifications performance characteristics and or model offerings without notice Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 0 Introduction 2 1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product notify the carrier of any damage that you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 Magnum 6K16 Series Managed Fiber Switch base unit configured with
6. 3 0 MST MSC _ FX __ mode 04 50 125 23 5 31 5 5 ra 100Mb Single 18 6KPV SSC Px mode 0 4 1300 9 125 15 31 ars 100Mb Single 40 6KPV px mode 0 4 1300 9 125 32 5 SSCL 6Kpv 100Mb Multi 1300 62 5 125 20 31 9 0 3 0 15 8 5 5 MTRJ FX mode 04 50 125 23 5 31 5 5 2 0 12 2 40 oKpy 100Mb Multi 1300 62 5 125 19 5 7 MLC FX mode 6KPV SLC 100Mb Single ag 1310 9 125 15 28 FX Mode 0 55 GBIC 1000Mb Multi 1300 62 5 125 9 5 17 5 5 2 12 5 SXSC mode 50 125 f 10 GBIC 1000Mb Single 1300 9 125 9 5 20 85 17 10 5 21 LXSC10 mode 25 GBIC 1000Mb Single 1550 9 125 4 0 21 15 375 17 5 43 LXSC25 mode GBIC 1000Mb Single 1550 9 125 4 0 21 15 175 70 ZXSC40 mode 70 GBIC 1000Mb Single 1550 9 125 3 0 23 18 20 5 102 ZXSC70 mode 46 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Note The use of either multi mode or single mode fiber to operate at 100Mbps speed over long distances i e in excess of approx 400 meters can be achieved only if the following factors are both applied e The 100Mb fiber segment must operate in full duplex FDX mode i e the full duplex factory default setting for 1OOMbps fiber ports must be used and e The worst case OPB of the fiber link must be greater than the fiber cable s passive Attenuation Attenuation Cab
7. 45 Ports and 2 100Mbps single mode FX SC type snap in 6KP6 RJMSSC connector 4 Port 10 100Mbps and 2 100 Mb SSC Fiber Port The Magnum 6KP6 RJSSC is also a Combo module equipped with 4 dual speed _ OY copper ports and 2 Single 2 TX LKRX mode SC type connectors It provides an advantage through combining copper and Fiber functions in one module of the 6K 16 Series Switch supporting four Copper and two single mode fiber network segments The 6KP6 RJSSC when installed ina Magnum 6K 16 Series Switch operates on copper at the 100m distance The Fiber is single mode and cable lengths can be as much as 25 Km see Power Budget Section 4 5 Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and a FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates 100Mbps speed when lit and at 10Mbps speed when off To distinguish the single mode 6 K6 RJSSC from the multi mode 6K6 RJMSC the label Sel M is at the top of the faceplate of the 6K6 RJSSC 5 2 4 6KP6 RJSSCL 4 10 100 Mb copper port and 2 100Mbps single mode FX SC type snap in connector The Magnum 6KP6 RJSSC is also a Combo module equipped with 4 dual speed copper ports and 2 Single mode Long Reach SC type connectors It provides a combination of copper and Fiber functions in one module to
8. FL Fiber Port MTRJ type plug in SFF Fiber multi model00BASE FX Fiber Port SC type snap in Fiber optic multi mode 1OOBASE FX Fiber Port ST type twist lock Fiber optic m mode 100BASE FX _ www GarrettCom com ss s 1 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Fiber Port 1 OOOBASE FX GBIC modules Fiber Single mode connector types Fiber Port SC type Fiber optic single mode 100BASE FX Fiber Port LC type Fiber SFF single mode 1OOBASE FX Fiber Port 1OOOBASE FX GBIC modules LEDs Per Port one set at the port one set on rear top 6K16V only Per Port one set at the port 6K16 LK Steady ON when media link is operational ACT ON with receiver port activity FDX HDX ON Full Duplex Mode OFF Half Duplex Mode 100 10 ON 100Mbps speed OFF 10 Mbps Operating Environment Ambient Temperature 40 to 140 F 40 to 60 C for UL60950 and Component Parts rating 60 to 205 F 50 to 95 C for IEC 60068 Type Test short term rating Storage Temperature 60 to 210 F 50 to 100 C Ambient Relative Humidity 5 to 95 non condensing Altitude 200 to 13 000 ft 60 to 4000m Conformal Coating humidity protection option Request quote Alarm Relay Contacts One NC indicating internal power one NC software controllable Packaging Enclosure Rugged High strength sheet metal Dimensions 9 5 in Hx 8 75 in Wx 1 75 in D 24 1 cm H x 22 2 cm W x 4 4 cm D Cooling me
9. Switch The Magnum 6K16 Series Switches incorporate an internal universal power supply and have a recessed male IEC connector for the AC power cord at the left rear A manual power ON OFF switch is adjacent A six foot 115 VAC 60 Hz standard power cord is supplied with each unit shipped within the United States and Canada The auto ranging power supply supports installation environments where the AC voltage is from 90 to 260 volts with a power input frequency between 47 and 63 Hz The 16 port units will consume over 20 watts of power typically When connecting the Ethernet cabling there is no need to power down the unit Individual cable segments can be connected or disconnected without concern for AC power related problems or damage to the unit Power supply options are available to suit the 6K 16 Series Switches to special high availability communications and or heavy industrial grade applications including 48VDC 24VDC and 125VDC with single DC input 48VDC 24VDC and 125VDC with dual source DC input See the Appendices of this manual for more details Use an RFQ for other variations 3 5 Alarm Contacts for monitoring internal power Software Traps The Alarm Contacts feature standard on Magnum 6K16 Series s provides two Form C Normally Closed NC contacts to which the user can attach two sets of status monitoring wires at the green terminal block When this option is present the terminal block for Alarm Contacts is part of the Power I
10. a fault in a ring topology E Relay Contacts for monitoring internal power and user defined software events Two Alarm Relay contacts monitor basic operations One is for hardware and will signal loss of power internally The other is software controllable and will signal user defined software events such as a security violation or an S Ring fault condition E Vertical mounting for efficient convection cooling no fans extended temp Mounting brackets for vertical mounting are included DIN Rail mounting hardware is optional Ethernet signal and power cables attach in the bottom Two sets of status LEDs one set viewable at the port connector and one set viewable from the front E Standard AC power input 48VDC or 24VDC or 125VDC input is optional Standard AC power input is IEC plug auto ranging for worldwide use For special applications models with 48VDC or 24VDC or 125VDC are available Dual Source DC input can also be selected and configured on the DC power input models E Heavy duty design for Industrial Ethernet and extended temperature operation Fiber ports take more power than copper ports but the Magnum 6K 16 Series design provides for this with heavy duty components The ambient temperature dual rating is 60 C per UL methods and 95 C per type test methods E MNS 6K licensed Network Management Software included S Ring optional Release 2 5 fall 03 includes SNMP Switch Management with secure access control RMON CLI Port
11. a Magnum FIBER Conngetion Et 6K16 Series a Factory Floor PLC Floor PLC ii 2 Storage serv ESD Internet Router FIBER Connection to other BLDG IB R Connection Factory Floor PLC Fig 2 4a The Industrial factory floor application with Magnum 6K16 Series Example 2 In another application a managed network is needed to provide a Redundant ring topology for maximum redundant network where any faulty cable or cable 24 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 disconnection or power failure in a ring switch can be reconfigured the network up running in mili seconds The ring topology of the network consists of high speed LAN segments supported by 100Mbps full duplex future proof fiber media to provide secure long distance LAN connection The entire network is sharing a higher bandwidth Gigabit enabled data mining server for the vital database located in a separate secured building The copper ports are required for multiple subnets inside the power plant to check the status of other Ethernet units The entire spread network will be manageable to provide easy detectable uninterrupted support through a viewable SNMP monitor The Magnum 6K16 Series Managed Fiber Switch equipped with the mix of copper and fiber ports provides an economical and seamless solution to the requirements The user configurable Magnum 6K16 Series provides an extra boost to the network requirement
12. are designed to support all standard Ethernet media types at 10 or 100 or 1000Mps speed Each 6K16 Series PM provides a wide selection of connecting Ethernet media segments with all similar or combo connector type _www GarettCom con sss 47 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Note The 6K16V Port modules are exactly similar in the functions size and price compared to 6K16 but addressed as e g 6KP8V RJ45 For a correct list of 6K16 6K16V Port Module types refer to Section 1 2 Each 6K16 Series PM is individually described in the following sections NOTE The port 1 on the RJ 45 ports on all the modules either all RJ 45 ports or used for COMBO module is set as other user ports 5 2 1 6KP6 RJMST 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX ST twist lock Combo Module The Magnum 6KP6 RJMST is a combo 6 port module of RJ 45 s at 10 100Mbps and fiber optic ports at 100MB The Combo module is equipped with dual mode ST type connectors and 6KP6 RJMST dual speed copper ports The 4 Port 10 100Mbps and 2 100 Mb ST Fiber Port ST connector functions as a fiber optic transceiver to support 1OOBASE FX network segments When installed in a Magnum 6K 16 Series Managed Switch the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic cable distances up the IEEE standard 100Mbps distance limits i e typically 2km at full dup
13. as a RESET for the Magnum 6K16 Series Switch B4 1 UL Requirements for DC powered units Minimum 18AWG cable for connection to a Centralized DC power source Minimum 14AWG cable for connection to a earthing wiring Use only with Listed 10A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent RWN gt Fastening torque of the lugs on the terminal block 9 inch pound max oy Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rack at least 4 inches apart with the first one located within 6 inches of the terminal block 64 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 B5 0 OPERATION Operation of Magnum 6K16 Series Switches with the optional 48VDC 24VDC and 125VDC power supply is identical to that of the standard AC powered models B6 0 ORDERING INFORMATION To order the optional 48VDC power supply factory installed add a suffix of 48VDC after the product s standard model Example Magnum 6K16 SeriesR 48VDC Similarly to order the optional 24VDC or 125VDC industrial specific power supply factory installed add a suffix of 24VDC or 125VDC after the product s standard model Example Magnum 6K16 Series 24VDC Magnum 6K 16 Series 125VDC B7 0 TROUBLESHOOTING Please refer to Section 6 0 for troubleshooting APPENDIX C Inte
14. flow control is to reduce the risk of data loss if a long burst of activity causes the switch to save frames until its buffer memory is full This is most likely to occur when data is moving from a 100Mb port to a 10 Mb port and the 10Mb port is unable to keep up It can also occur when multiple 100Mb ports are attempting to transmit to one 100Mb port and in other protracted heavy traffic situations Magnum 6K16 Series Switches implement the 802 3x flow control non blocking on Full Duplex ports which provides for a PAUSE packet to be transmitted to the sender when the packet buffer is nearly filled and there is danger of lost packets The transmitting device is commanded to stop transmitting into the 6K16 Series Switch port for sufficient time to let the Switch reduce the buffer space used When the available free buffer queue increases the Switch will send a RESUME packet to tell the transmitter to start sending the packets Of course the transmitting device must also support the 802 3x flow control standard in order to communicate properly during normal operation Note When in Half Duplex mode the 6K16 Series Switch implements a back pressure algorithm on 10 100 Mb ports for flow control That is the switch prevents frames from entering the device by forcing a collision indication on the half duplex ports that are receiving This temporary collision delay allows the available buffer space to improve as the switch catches u
15. securely anywhere on their Network setup _www GarrettCom con ss 23 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The option for setting the ports at 10 or 100Mb on copper and supporting the 10 or 100Mb fiber media provide a very widespread option to the users to mix match their legacy and advance network needs The modularity of the 6K 16 Series Managed Fiber Switch makes it an attractive choice for use in applications with LAN connections to an organization s multiple site offices and factory floors The different locations can be easily connected together with the Fiber ports supported by the Magnum 6K16 Series Switch A main NT server in a secure area protected from earthquake or fire hazards can be connected to the full duplex Gigabit Fiber port Extended temp ratings and wide options of AC DC power supply qualifies this managed 6K16 Series switch to use in temp controlled network floor and many others temp sensitive critical Industrial applications where above normal room temp is required to operate the network Full duplex future proof fiber media can easily connect long distance subnets and provide a stable secure network to all applications The SNMP management capability of the Magnum 6K16 Series Switch helps create a database of all the network subnets to easily manage the network Magnum 6K25 Fe eae hii SNMP Monitor H E Main SERVER IBER Connection a FIBER Conngction
16. single mode SC 10Km One 1000BASE LX LH GBIC LXSC25 port 1310nm single mode SC 25Km One IEEE 802 3ab TP GBIC TP port RJ 45 connector One 1000BASE ZX GBIC ZXSC40 port 1550nm single mode SC 40Km One 1000BASE ZX GBIC ZXSC70 port 1550nm single mode SC 70Km The Gigabit ports are set by factory as AUTO by default but can be configured as per the convenience using the MNS 6K management firmware 2 2 8 Packet Prioritization 802 1p QOS Quality of Service means providing consistent predictable data delivery to users from datagram paths that go all across a network As a LAN device the Magnum 6K16 Series can do its part to prevent any QOS degradation while it is handling Ethernet traffic through its ports and buffers The Magnum 6K16 Series switching hardware supports the IEEE 802 1p standard and fulfills its role in support of QOS giving packet processing priority to priority tagged packets according to the 802 1p standard In addition to hardware support for QOS the MNS software R2 supports two priority queues that can be shared across the eight levels of defined packet priorities for application specific priority control by the user through software configuration settings www GarrettCom com 19 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 2 9 Frame Buffering and Flow Control Magnum 6K 16 Series s are store and forward switches Each frame or packet is loaded into the Switch s memor
17. the 6K16V securely in position even with cabling attached to the unit To release the 6K16V from the DIN Rail mounting press the top of the two DIN Rail latches down simultaneously to release the 6K 16V so that it can be dismounted by pulling the bottom out Once the bottom of the 6K16V is rotated out the DIN Rail latch is not engaged and the 6K16V can be moved up and out free of the DIN Rail mounting The picture below is a front right side view of a DIN Rail mounted 6K16V It shows vertical mounting of Magnum 6K16V on a DIN Rail track for proper convection cooling of the unit Note that there is air space in the rear as the 6K16V unit is held out from the rear of the panel by the mounting brackets The 6K 16V design uses the case for cooling patent pending and needs to be mounted vertically with air flow space in the front rear and sides Fig 3 3 1 Magnum 6K16V mounted vertically with DIN Rail brackets and latches Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The DIN Rail mounting brackets and latches are optional and need to be ordered as separate items e g Model DIN RAIL VRM 3 3 1 Mounting Dimensions for 6K16Vwith metal brackets Each Mangum 6K16V is supplied with metal mounting brackets and screws to mount the unit securely It is recommended to mount the 6K16V vertically as shown below for proper cooling and long life reliability It is also advisable to mount the unit with s
18. user selected port module options installed 1 AC Power Cord U S and other 115 VAC only if AC version 1 Set of two metal vertical mounting brackets with screws to the case 1 Installation and User Guide this manual 1 Product Registration Card Remove the items from the shipping container Be sure to keep the shipping container should you need to re ship the unit at a later date To validate the product warranty please complete and return the enclosed Product Registration Card to GarrettCom Inc as soon as possible In the event there are items missing or damaged contact the party from whom you purchased the product If the unit needs to be returned please use the original shipping container if possible Refer to Section 6 Troubleshooting for specific return procedures Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 2 Product Description Magnum 6K16 Series 6K16 6K16V Magnum 6K16 Series Managed Switches available as Magnum 6K16 and 6K16V models and equipped with 16 modular ports is specially designed to focus on two different aspects of Ethernet markets to meet their needs and requirements 6K16 Series managed switches provide modularity of fiber and copper ports a mix and combination of 10Mb 100Mb and Gigabit speed ports with comprehensive management software in a compact industrial grade package Setting a new standard for Industrial and Carrier Class applications heavy duty Ethernet Switc
19. 00Mbps 15 us packet time 10 to 10 Mbps and 10 to 100Mbps Network Standards and Compliance hardware Ethernet V1 0 V2 0 IEEE 802 3 1OBASE T IEEE 802 3u 100Base TX 100BASE FX IEEE 802 3z 1000OBASE TX Ethernet Auto Negotiation IEEE 802 3ab 1OOOBASE TX Ethernet IEEE 802 1p Priority protocol IEEE 802 1d Spanning tree protocol IEEE 802 1q VLAN Tagging IEEE 802 3x Flow Control Maximum 10 Mbps Ethernet Segment Lengths Unshielded twisted pair 100 m 328 ft Shielded twisted pair 150 m 492 ft 10BASE FL multi mode fiber optic 2km 6 562 ft 10BASE FL single mode fiber optic 10 km 32 810 ft Maximum Standard Fast Ethernet Segment Lengths 10BASE T CAT 3 4 5 UTP 100 m 328 ft 100BASE TX CAT 5 UTP 100 m 328 ft Shielded twisted pair 150 m 492 ft 100BASE FX half duplex multi mode 412 m 1350 ft 100BASE FX full duplex multi mode 2 0 km 6 562 ft 100BASE FX half duplex single mode 412 m 1350 ft 100BASE FX full duplex single mode 20 0 km 66K 16 Series ft 100BASE FX full duplex Long Reach 40 0 km 122K ft Maximum Standard Gigabit Ethernet Segment Lengths 1000BASE T CATSe or higher is recommended 100 m 328 ft 1000BASE SX full duplex multi mode 62 5um cable 220m 1000BASE SX full duplex multi mode 50um cable 550m 1000BASE LX full duplex single mode 62 5um cable 5Km Fiber Multi mode connector types supported Fiber Port ST type twist lock Fiber multi mode 10Mb 10BASE
20. 5 below If the problem is corrected the Magnum 6K16 Series Switch and its associated cables are functioning properly 5 If the problem continues after completing Step 4 above contact your supplier of the Magnum 6K16 Series Switch unit or if unknown contact GarrettCom Inc by fax phone or email support garrettcom com for assistance 6 2 When Calling for Assistance Please be prepared to provide the following information l A complete description of the problem including the following points a The nature and duration of the problem b Situations when the problem occurs c The components involved in the problem d Any particular application that when used appears to create the problem 2 An accurate list of GarrettCom product model s involved with serial number s Include the date s that you purchased the products from your supplier 3 It is useful to include other network equipment models and related hardware including personal computers workstations terminals and printers plus the various network media types being used _www GarrettCom con sss 60 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 4 A record of changes that have been made to your network configuration prior to the occurrence of the problem Any changes to system administration procedures should all be noted in this record 6 3 Return Material Authorization RMA Procedure All returns for repair must be ac
21. 8 RJ45 Twisted Pair 10 100Mb 8 Port eeeeeeeneees 55 5 2 10 PoE Power Pass through PoKP8V RJ45 MDIX 008 56 5 2 11 6KP8 45 2MT Combo Module ceeesseseeseeeeceseeeeeeeeaeeneens 57 5 2 12a 6KP8 45 2LC Combo Module ce eeeeeseeeeseeeeceeeeeeeeenees 57 5 2 13 GBIC SXSC Gigabit fiber 1000Mb MM SC Connector 57 5 2 13a GBIC LXSC Gigabit fiber 1000Mb MM SC Connector 58 5 2 14 GBPM 2OTX Two Gigabit option 59 5 2 15 OK M BLNK erccrsitiperetisr rore ironi EEK EPEE EE EEEE EAE E TERR 59 6 0 TROUBLESHOOTING sessessssesesesceessoeseseseeceseroesesesorosseseeecoeeosoeseseseee 59 6 1 Before Calling for Assistance seeeseeeeseseeesrerrerererrsrrrrrrererrrsererens 60 6 2 When Calling for Assistance 0 cccccesceseesecseeeceeseeeeeseeeneeseeeseeees 60 6 3 Return Material Authorization RMA Procedure ceseeeeees 61 6 4 Shipping and Packaging Information ceeeeeeeeeeeeeeeneeeeeeeeneees 61 APPENDIX A WARRANTY INFORMATION cccccsssscscsscssscscssseeseee 62 APPENDIX B Internal DC Power Supply Options cssscssssesssees 62 APPENDIX C Internal DC Dual Source Power Option scssssee 65 Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 Revisions 03 09 Rev C added UL Safety statements see page iii 06 07 05 07 04 06 10 05 02 05 07 04 01 04 12 03 Minor updates to power supply ratings minor
22. GarrettCom within two weeks of your purchase APPENDIX B Internal DC Power Supply Options B1 0 SPECIFICATIONS FOR MAGNUM 6K16 SERIES SWITCHES DC POWER Magnum 6K16 Series models for 48V and 24V DC amp 125VDC and 5V Power input Each Magnum Model 6K16 Series Managed Switch DC option requires a DC power source for 24VDC 48VDC and 125VDC option or 5VDC input The wide range of power input qualifies this product for use in 24VDC 48VDC as well as 125VDC or SVDC environments The 24VDC 48VDC or 125VDC or SVDC power input provides an Ethernet networking product utilizing a special type of power supply with a proven high reliability record to fulfill the DC requirement DC Power Terminals internally floating GND Terminal for earth or ground wire connection to the 6K 16 Series chassis Input Voltage 18 to 36 VDC 24VDC Input current 1 2Amps max for all RJ 45 ports Input current 2 4Amps max for all Fiber ports Input Voltage 36 to 70 VDC 48VDC Input current 0 8Amps max for all RJ 45 ports Input current 1 2Amps max for all Fiber ports Input Voltage 115 to 150 VDC 125VDC Input current 0 3Amps max for all RJ 45 ports Input current 0 35Amps max for all Fiber ports Power Consumption 50 watts max for fully loaded fiber ports www GarrettCom com ss 62 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 24V 48V 125V DC 30 watts typical for al
23. INK must be strong enough to N provide power to the 6K switch and to all the 8 RJ 45 ACTIVITY FULL HALF _ www GarrettCom com ss 56 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 ports with PD devices connected up to 15 watts per PoE port e Inthe case where the 48VDC power in not internally connected and no power is coming to the PoE ports for some reason all the PoE port LEDs are ON simultaneously to indicate a trouble condition The ports will still operate properly for data traffic 5 2 11 6KP8 45 2MT 6 10 100Mbps RJ 45 and 2 100Mb multi mode FX MTRJ Small Form Factor The Magnum 6KP8 45 2MT eight port Module is a combo module with copper and fiber Small Form Factor MTRJ type ports The small sizes of MTRJ connectors give an advantage of placing more fiber ports on one module The 6KP8 45 2MT is equipped with six 10 100 RJ 45 ports and two 100Mb MTRJ fiber ports When installed in a Magnum 6K16 Series Switch it supports the standard distances as mentioned on 5 2 3 and the LEDs also act similarly 6KP8V 5 2 12a 6KP8 45 2LC 6 6 Port 10 100Mbps_ amp 2 port 100Mbps 10 100Mbps RJ 45 and 2 100Mb SingleMode Fib ort LC single mode FX LC Small Form Factor 6KP8 45 2SLC The Magnum 6KP8 45SLC eight port Module is a combo module with copper and fiber Small Form Factor LC type fiber ports The small size of LC connectors give an advantage of placing more ports on
24. K 16 Series provides switched connectivity at Ethernet wire speed among all of its ports The Magnum 6K16 Series supports10 100Mbs for copper media and 10 or 100Mb separate traffic domains for fiber ports to maximize bandwidth utilization and network performance All ports can communicate to all other ports in a Magnum 6K 16 Series but local traffic on a port will not consume any of the bandwidth on any other port Magnum 6K 16 Series units are plug and play devices There is no software configuring necessary to be done for basic operation at installation or for maintenance The only hardware configuration settings are user options for an UP LINK Switch resides inside the unit on the 6K P8 RJ45 Optional Half Full duplex mode and 10 or 100Mbps selection for the switched ports must be configured through MNS software per unit as per the requirement The internal functions of both are described below Filtering and Forwarding Each time a packet arrives on one of the switched ports the decision is taken to either filter or to forward the packet Packets whose source and destination addresses are on the same port segment will be filtered constraining them to that one port and relieving the rest of the network from having to process them A packet whose destination address is on another port segment will be forwarded to the appropriate port and will not be sent to the other ports where it is not needed Traffic needed for maintaining the un int
25. KP8 45LC Module is a combo module with a combination of copper and Fiber Small Form Factor LC type ports The small size of LC connectors allows an ACTIVITY Q FULL HALF advantage of having more ports on one module The Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 6KP8 45LC is equipped with 4 10 100 RJ 45 ports and 4 LC Small form factor multi mode fiber ports When installed in a Magnum 6K16 Series Switch it supports the standard distances as per mentioned on 5 2 8 and the LEDs also acts similarly as mentioned above 5 2 9 6KP8 RJ45 Twisted Pair 10 100Mb 8 Port The 6KP8 RJ45 module supports Ethernet twisted pair segments of any standard length It is equipped with an eight port RJ 45 connector and offers 10 100 full half duplex auto 6KP8 RJ45 negotiating capability on each port The RJ 45 connector is shielded to 8 Port 10 100Mb Copper ports minimize emissions and will allow both unshielded twisted pair UTP and shielded twisted pair STP cable connections The 6KP8 RJ45 module is equipped with a Media Dependent Auto Crossover MDI X switch which controls all ports for cascaded connection This feature eliminates the need for a special twisted pair crossover cable when connecting to a hub or another switch Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit a FD
26. L Industry standard serial cable DB 9 connectors for RS 232 null modem connection sometimes called an X modem cable used to connect a PC or a character terminal to the Management port CONSOLE USB Industry standard serial cable DB 9 connectors for RS 232 null modem connection sometimes called an X modem cable to connect to a managed switch and a USB port to connect to a PC Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Please see next page for PoE option and Modules 6K PoE Modules with 48VDC Pass Through Configuration options only one A B or C module slot of 6K Series switch with 48VDC power input may be configured with a PoK Modules P6KP8 RJ45 8 port PoE module for 6ks with 48vdc PS w eight PoE power source 10 100 auto negotiating auto cross RJ 45 ports P6KP8 45RJ 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 10 100 auto negotiating auto cross RJ 45 ports P6KP8 45MT 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX MTRJ connectors P6KP8 45MLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 2km mm FX LC connectors P6KP8 45SLC 4 4 port PoE module for 6ks with 48vdc PS w four PoE power source and four 100 Mb 15km sm FX LC connectors P6KP8 45 2MT 6 2 port PoE module for 6ks with 48vdc PS w four PoE power source and two normal RJ 45 10
27. MPERATURE UNCONTROLLED LOCATIONS 6 10 100 AND 2 100MB FIBER PORTS CAN BE CONNECTED IN STRINGS MIXED MEDIA FIBER HUB 16 PORT 10 100 AUTO SENSING DUAL SPEED 8 PORT AND 16 PORT 10 100 AUTO SENSING HUBS PERSONAL SWITCHES 10 100MB 8 PORT DUAL SPEED AUTO NEGOTIABLE WITH FIBER OPTION PERSONAL HUBS 100MB OR 10 100MB 8 PORT WITH 2 SWITCHED PORTS 1 FIBER BUILT IN PERSONAL HUBS 10MB SERIES 8 PORT AUI STACKABLE TO 5 HIGH OPTIONAL BNC OF FIBER PORT 8 OR 9 PORT AND 4 OR 5 PORT PERSONAL HUBS W MAN UP LINK SW MEDIA CONVERTERS 10MB AND 100MB SERIES ALL MEDIA COMBINATIONS INCL FIBER ST SC MM SINGLE MODE THE X LINE OF CONFIGURABLE MIXED MEDIA PRODUCTS STACKABLE CONCENTRATORS SNMP OPTIONAL 13 PORTS MINI CONCENTRATORS 7 PORTS REPEATERS 2 PORTS REPEATER PORT MODULES RPMS 6 TYPES FOR ETHERNET MEDIA COAX TRANSCEIVERS 10MB SERIES APR 07 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 1 0 SPECIFICATIONS 1 1 Technical Specifications Performance Filtering Forwarding Rate Ethernet 10Mb 14 880 pps Fast Ethernet 100Mb 148 800 pps Gigabit Ethernet 1000Mb 1 488 000 pps Switching Processing Type Store and Forward with IEEE 802 3x full duplex flow control non blocking Data Rate 10Mbps 100Mbps and 1000Mbps Address Table Capacity 4K node self learning with address aging Packet buffer size 240KB for 10 100 and 120KB for 1000Mb Latency 5 us packet time 100 to 1
28. P8 RJ45 TP Module w eight 10 100Mbps auto negotiating RJ 45 ports 6KP8 45MT 4 4 module w four RJ 45 ports and four 2km mm FX MT RJ s 6KP8 45MLC 4 4 module w four RJ 45 ports and four 2km mm LC connectors 6KP8 45SLC 4 4 module w four RJ 45 ports and four 2km sgl m LC connectors 6KP6 RJMST 4 2 module w four RJ 45 ports and two 2km mm FX ST s 6KP6 RJMSC 4 2 module w four RJ 45 ports and two 2km mm FX SC s 6KP6 RJSSC 4 2 module w four RJ 45 ports and two 20km Sgl m FX SC s 6KP6 RJSSCL 4 2 module w four RJ 45 ports and two 40km Sgl m FX SC s 6KP6 MT10ST 4 2 module w four MTRJ ports and two 10Mb 2km FL ST s 6KP6 RJ10ST 4 2 module w four RJ 45 ports and two 10Mb 2km FL ST s Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 6KM BLNK Blank cover for one 6K16 Series A B module slot opening in a 6K16 Series Gigabit 1000Mb module option for Magnum 6K16V 6KP5 G4RJ G 2 module w one GBIC transceiver and four 10 100 RJ 45 connectors 6KP3 G2SC G 2 module w one GBIC transceiver and two 100Mb 2km FX SC fiber ports connector GBPM 20TX Two port Gigabit 6K module for 6K16 Series Switches provides two GBIC open transceiver port for a user selectable GBIC transceiver module GBPM COTX One slot Gigabit 6K module for 6K16 Series Switches uses one 6K16 Series slot and provides one GBIC open transceiver port for a user selectable GBIC t
29. Power Budget Calculations for Magnum 6K 16 Series PM s with Fiber Medias Misc iite n ee e E E 45 5 0 Introduction Magnum 6K16 6K16V Managed Fiber Switch Port Mdulle scssccsseesssescscscesscssscsssvsssnecsncssesssesesssssesnsesssesssessenesenesseseee 47 5 1 Inspecting the Package and Product cccccceesceseeseceteceeeeneeeneeenes 47 5 2 6KPM Module Description eceecceecceseceseceeecececeeeaeeeneeneeeseenes 47 5 2 1 6KP6 RJMST Combo Module eee ceeeccseesceseeeeseceeeereneees 48 5 2 la 6KP6 RJLOST Combo Module uu ceeccesceeceseceseeeteeseeeneeenes 48 5 2 1b OK P4 FLOST Module ccc eeeceeecsseeecesecseeeecneeeeceaeeeceaeeateneens 49 5 2 lc O6KP4 FLSTFX Module 0 0 eeceseeecsseseeeeeeseeeceeeaeeecneeaeereneeas 50 5 2 2 6KP6 RJIMSC Combo Module 0 cceeceeeeceeereeeeeeeeeeeeeneees 50 5 2 3 6KP6 RJSSC Combo Module ceeceeecseeeceseeeesecneeeeeneees 51 5 2 4 6KP6 RJSSCL Combo Module cc eececeeeeeeeeeeereesecereeeeneees 51 5 2 44 6KP6 RJ10ST Combo Module 00 ec ceeceeeeeseeeeeeeeeeeeneeereneees 52 5 2 5 OKP8 MTRJ Module ee eeeeceeceseeesseeseeeeeseceeeeeceaeeeceaeeaeeneeas 52 5 2 5a 6KP6 MTIOST Combo Module cee ceeeecseeeceeeeeeeseeeeeneens 53 5 2 6 OKP8 45MT Combo Module ce eececceseeseesceeeceseeeeeeeneeeeeneees 53 5 2 7 OKP8 MLC Module ceeeceeeeeceeeeeeecseeseceeverceaeeeeeaesaeeeeeneees 54 5 2 8 6KP8 45LC Combo Modul ee eeceecceseeceeseceeeeeceeeeeeeseeeeeaeens 54 5 2 9 6KP
30. Security Port Mirroring Port Settings Control Telnet TFTP FTP support Spanning Tree Protocol Link Loss Learn S Ring with license key multi level QoS Port and tag based VLANs GVRP IGMP Snooping SNMPc GUI support Event Log SNTP client for time of day BootP and DHCP client for IP configuring and password security Web management is in beta test MNS 6K software is factory installed supported and updated via Internet and GCI FTP Server www GarrettCom com 22 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 4 Applications Magnum 6K 16 Series Fiber Switches offer high performance modularity and availability They provide the flexibility of 100Mbps fiber and copper ports as well as single or dual Gigabit 1000Mb ports with industry standard LAN management software Magnum 6K16 Series Switches are easily used in a variety of applications including client server computing secure VLAN performance upgrades to departmental networks and stream traffic for VOIP and audio video applications or a very diversified combination of mixed media in Industrial floor applications The performance characteristic of the 6K16 Series Switches enables them to inter connect a series of subnets one subnet per 6K16 Series Switch port in a LAN traffic center The subnet connections may be via fiber or twisted pair cabling 100Mbps or 10 Mbps speed and full or half duplex The mixed media modular capability is ideal for In
31. Series Switch to connect to any 10Mb hub or media converter or almost any other device with a 10Mb fiber Ethernet port The default setting of 100Mb fiber module is full duplex User mode control per port through the MNS port settings software is the same as the other 6K 16 Series modules The fiber ports support fiber cabling distances according to the 1 OBASE FL and 100BASE FX standards i e 2km distance for multi mode fiber Single mode for up to greater distance may be available as a special order request quote 2 2 7 Gigabit 1000Mbps port modules The Magnum 6K 16 Series offered a wide option Gigabit speed with multiple choice for the modular slot While up to two Gigabit modules maxm can be configured in the modular slot The Gigabit port option for the modular slot comes in couple of different configuration The two Giga port has been offered as GBPM 20TX fiber or RJ 45 whereas the single Gigabit module comes in flavor of G 4 10 100 RJ 45 ports or G 2 100Mb fiber ports as shown below in the figure ae TX GLK RX pt 3 1 1000Mb Fiber SC 2 T00Mb SC 1 1000Mb Fiber SC 4 10 100Mb The 6K16 Series Modules provide a GBIC opening for insertion of industry standard GBICs to provide Gigabit Gb media flexibility GBIC models are available for both multi mode 550m and single mode 10 25 40 70 km fiber options and for Gigabit copper as well with new models appearing often www GarrettCom com 17 Mag
32. T 4 Port 10Mb ST Fiber Port The Magnum 6KP4 F10ST is a 1OMb multi mode fiber module with 4 ST Fiber ports All four fiber ports are ST connectors and configured as 1OMb Half duplex by default RRA The 10Mb ST fiber ports E allow the user to connect their legacy 10Mb network ZETA EK RX to the Magnum 6K16 Series switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as 6KP4 RJ10MST a special order 4 Port 10Mb ST Fiber Port Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper 3 1 TX BLK RX connectivity with the remote cT aq Sa HLS device when lit and 2 TX GLK RX FDX HDX LED indicating full duplex mode when lit or half duplex if off 49 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 5 2 1lc 6KP4 FLSTFX 2 10Mb amp 2 100Mb multi mode FX ST twist lock Module The Magnum 6KP4 FLSTFX is a combo fiber module with two 10Mb two 100Mb multi mode fiber module and in combine 4 ST Fiber ports All four fiber ports are ST connectors and configured as 10Mb Half duplex by default for 10Mb fiber and 100Mb Full duplex for the 100Mb fiber The 10Mb ST fiber ports allow the user to connect their legac
33. TRJ 6KP8 MLC 100Mb 13 2 2 3 8 Port Copper Module 6K P8 RI45 00 ee eccceeceseceteeeecseeeneeenes 14 2 2 4 PoE Power Pass through P6KP8 RJ45 10 100Mb 8 port 15 2 2 5 6 Port 4 2 Combo Modules sseeseeeeseseeereersrsseserereeese 16 2 2 6 4 Port 10 Mb and 100Mb mm Fiber ST Modules 00 17 2 2 1 Gigabit 1000Mbps port modules ee eeeeeeeeneeereeeeeeeeeeees 17 2 2 8 Packet Prioritization 802 1p QOS cecccccsseesseeeeeeeeeeeeseeeeeees 19 2 2 9 Frame Buffering and Flow Control 20 2 2 10 Managed Network Software MNS 6K cccccccesseeeseeteeeeeees 20 2 3 Features and Benefits 0 00 ecesesccssecseeeecneceeceseeeeesecaeeeeeaecaeeseenereees 22 DA Applications 55265 sesh sbease this eek EE Ea E EA EEE AE 23 3 0 Installation scscssssssessssesssssrsssessscsesesssssssessssssessessesssssssesssssnseseeees 27 3 1 Locating Magnum 6K 16 Series Switches cesesceseceteseeeseeeees 27 3 2 Connecting Ethernet Media cc eeccecceeeseceseceseceeecseeeneeeeeeneeeereees 27 3 2 1 Connecting Fiber Optic ST type twist lock 28 3 2 2 Connecting Fiber Optic SC type Snap In esseere 28 3 2 3 Connecting Single Mode Fiber Optic cecceceeseeseeeteeteeeeeees 29 3 2 4 Connecting Twisted Pair RJ 45 CAT3 CATS Unshielded or Shielded ocs nai eter nia Eae Ee es mene tents 29 3 2 5 Connecting Twisted Pair CATSE or better Unshielded or Shielded meee eters errr etnre
34. User Guide 03 09 2 2 1c Magnum 6K16 Series family 6K16 and 6K16V Comparison chart Horizontal Rack mount Vertical Din Rail Panel Temp Rating Office amp Factory Factory amp Outdoors Rest Only Vv suffice module Module Model s e g 6KP8 RJ45 e g 6KP8V RJ45 Front with ports Front and rear top Special Ratings NEBs and ETSI P1613 for substations MNS 6K Software Managed preloaded LLL STP RSTP S Ring me Controlled via Alarm Contact Hardware amp Software Same Copper amp Fiber Port Module can be 10 100 or 1000Mb Suitable for Application p Telco Office Industrial tility Industrial Outfloors p p Operation Note The Redundant S Ring feature for self healing ring sold separately 2 2 2 8 port SFF fiber modules 6KP8 MTRJ 6KP8 MLC 100Mb ug n Play a Fig 2 2 2 SFF Fiber Port 1 3 5 7 ae Fm Modules 3 Fe 6KP8 MTRJ to the left and bs 6KP8 MLC or SLC e r PA below Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 In an eight port SFF fiber port module all of the fiber ports are of the same speed 100Mb mode and connector type Models are available with Small Form Factor SFF are multi mode MT RJ or LC type connectors and single mode LC type connectors The 100Mb fiber eight port modules for the Magnum 6K16 Series s normally are set factory default to operate in full duplex mode for best fiber distance and performance Using the 6K MNS softw
35. X HDX LED to indicate full duplex mode when lit or half duplex when off and a 10 100 LED indicating 100Mb when lit or 10 Mbps when off Important Note The 10 100 RJ 45 ports are supported with Auto negotiation and Auto crossover MDIX which allow the RJ 45 ports to automatically Link with any RJ 45 device and eliminate the use of cross over cable NOTE for Power Substations In support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the RJ 45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity i e less than 2 meters or 6 5ft to the 6K16 V It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce kigh greater than 2500V levels of ground potential rise GPR during line to ground fault conditions The 6K16 V passes the 1613specifications for zero packet loss with fiber ports amp with RJ45 ports used as indicated here _ www GarrettCom com ss 55 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 5 2 10 PoE Power Pass through model P6KP8V RJ45 MDIX 10 100Mb 8 port The PoE RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices per the IEEE802 3af PoE capes sta
36. accomplished by using a family of different port Modules which can be individually selected and configured per port See Section 2 4 for a description of the PMs The various media types supported along with the corresponding IEEE 802 3 802 3D 802 3u 802 3AB and 802 3z standards and connector types are as follows _ www GarrettCom com ss 27 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 IEEE Standard Media Type Max Distance Port Module Fiber 100BASE FX mm Fiber 220m ft GBIC SXSC sgl m Fiber 5Km GBIC LXSC 100BASE FX mm Fiber 2 0km 6 562 ft 6K6 MSC MST sgl m Fiber 18 0km 95K ft SSC SSCL small form factor mm Fiber 2 0km 6 562 ft 6KP8 MTRJ MLC small form factor sgl m Fiber 15 km 6KP8V SLC Copper 10BASE T and 100BASE TX twisted pair 100m 328 ft 6KP8 RJ45 1 mm multi mode z sgl m single mode 3 2 1 Connecting Fiber Optic ST type twist lock The following procedure applies to installations using a PM with ST type fiber connectors This procedure applies to ports using a 6K 16 Series module MST type port 1 Before connecting the fiber optic cable remove the protective dust caps from the tips of the connectors on the PM Save these dust caps for future use 2 Wipe clean the ends of the dual connectors with a soft cloth or lint free lens tissue dampened in alcohol Make certain the connectors are clean before connecting Note One strand of the duplex fiber optic cable is coded
37. agnum 6K16 Magnum 6K16 Managed Carrier Class Switch base unit for Horizontal or rack mounting Worldwide AC power May be configured with a selection of 10 100 1000 fiber and copper port connector types 16 total ports max Wire speed filtering and forwarding across all ports 802 3x flow control 802 1p priority packet processing self learning 4K node address table large 240KB packet buffers for 10 100 and 120KB for 1000Mb For licensed managed networks software MNS 6K and S ring See separate data sheets Magnum 6K16 24VDC Same as 6K16 except the power input is 24VDC Magnum 6K16 48VDC Same as 6K 16 except the power input is 48 VDC Magnum 6K16 125VDC Same as 6K16 except the power input is 125VDC Configuration Options Each Magnum 6K16 base unit has TWO port module slots Magnum 6K16 Port Modules 6KP8 MTRJ SFF Fiber module w eight 100Mb mm FX MT RJ connectors 6KP8 MLC SFF Fiber module w eight 100Mbps mm FX LC connectors 6KP8 SLC SFF Fiber module w eight 100Mbps sgl m FX LC connectors 6KP4 FXSC 2 2 100Mb Fiber module w four 100Mb 2km FX SC connectors 6KP4 FXST 2 2 100Mb Fiber module w four 100Mb 2km FX ST connectors 6KP4 F10ST 2 2 10Mb Fiber module w four 1OMb 2km FL ST connectors 6KP4 FLSTFX 2 2 ST Fiber module w two 100Mb amp two 10Mb ports 2km 6KP8 45 2MT 6 2 module w six RJ 45 ports and two 100Mb 2km FX MTRJ s 6KP8 45 2LC 6 2 module w six RJ 45 ports and two 100Mb 2km FX LC s 6K
38. ain all connectors and this Installation Guide CAUTION Do not pack the unit in Styrofoam popcorn type packing material This material may cause electro static shock damage to the unit 2 Clearly mark the Return Material Authorization RMA number on the outside of the shipping container 3 GarrettCom is not responsible for your return shipping charges 4 Ship the package to GarrettCom Inc 47823 Westinghouse Dr Fremont CA 94539 7437 Attn Customer Service www GarrettCom com 61 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 APPENDIX A WARRANTY INFORMATION GarrettCom Inc warrants its products to be free from defects in materials and workmanship for a period of three 3 years from the date of shipment by GarrettCom During this warranty period GarrettCom will repair or at its option replace components in the products that prove to be defective at no charge other than shipping and handling provided that the product is returned pre paid to GarrettCom This warranty will not be effective if in the opinion of GarrettCom the product has been damaged by misuse misapplication or as a result of service or modification other than by GarrettCom GarrettCom reserves the right to make a charge for handling and inspecting any product returned for warranty repair which turns out not to be faulty Please complete the warranty card as this acts as a product registration and mail it to
39. allow the basic and advanced info about the Magnum MNS 6K management software and a useful tool for first time user or email support GarrettCom com for further information 21 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 3 Features and Benefits E Managed switching for high performance Ethernet LANs Magnum 6K16 Series Switches provide non blocking all ports can run at full speed at once performance with standard Managed Networks Software MNS 6K included They are typically used in LAN traffic centers with 16 100Mb or 8 2 Gigabit ports for backbone connections where managed network services are desired E Switching services includes 802 1p QoS packet prioritization The Magnum 6K 16 Series switching hardware supports QoS giving packet processing priority to priority tagged packets according to the IEEE 802 1p standard For port and application specific priorities of data the QoS software may be configured E Features Fiber Built In Magnum 6K16 Series Managed Fiber Switches are designed to naturally include fiber ports and support mixes of multi mode and single mode 10 Mb 100Mb and 1000Mb speed full and half duplex classic Small Form Factor SFF and GBIC fiber connectors RJ 45 10 100 ports can also be configured in the mix of port types E S Ring and Link Loss Learn for reliable high availability using ring topology S Ring along with the Link Loss Learn feature provides reliable fast recovery of
40. are the user may select full or half duplex mode per port through set up of the software See Magnum 6K MNS Software Manual for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices There are three LED s per fiber port The Link LK LED indicates ready for operation on that port when lit the F H LED indicates operation in full duplex mode when ON half duplex when OFF and the blinking ACT LED indicates receiving Activity on the port A fiber cable must be connected into a SFF port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port 2 2 3 8 Port Copper Module 6KP8 RJ45 The 6KP8 Series s 8 port Copper port module model 6K P8 RJ45 provides eight 10 100Mb switched RJ 45 ports The 10 100Mb switched ports normally as a default setting are independently N way auto negotiating and auto crossover MDIX for operation at 10 or 100Mb speed in full or half duplex mode i e each independently selects a mode and speed to match the device at the other end of the twisted pair cable See Section 4 3 for auto negotiation and MDIX details The auto crossover feature will automatically determine the other side of connection to make the connection and eliminate the need of cross over cable 14 Magnum 6K16 Series Managed Fiber Switch Installatio
41. are key to the flexibility and adaptability 2 2 la Magnum 6K16V Managed Fiber Switch The Magnum 6K16V model of 6K16 Series family is primarily designed to use for vertical mount applications Equipped with the multi media fiber copper solutions GarrettCom multiple speed 10 100 1000Mb support rich MNS 6K management features hardware and software alarms and convection cooling no fans the Magnum 6K16V easily qualifies for use in transportation and traffic control systems power utilities and industrial factory floors For the fast growing demands of video surveillance systems with segments requiring Gigabit backbone interconnections the Magnum 6K16V managed switches are easy to install and operate The next generation of industrial applications will need advanced managed network software operation at extended temperatures fiber ports modularity support for self 10 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 healing ring structures redundancy security and gigabit backbone configurability The Magnum 6K16V has all of these in a very sleek and robust metal case with a wide choice of popular DC options or industry standard AC internal input The plug n play Magnum 6K16V managed fiber switch should be mounted vertically using the vertical mounting brackets which come with the unit or by using the DIN RAIL KIT optional for Din rail mounting Loaded with versatile management software
42. ble with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established NOTE for Power Substations In support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the RJ 45 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity i e less than 2 meters or 6 5ft to the 6K16 V It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce kigh greater than 2500V levels of ground potential rise GPR during line to ground fault conditions The 6K16 V passes the 1613specifications for zero packet loss with fiber ports amp with RJ45 ports used as indicated here _ www GarrettCom com ss 29 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 2 5 Connecting Twisted Pair CATS5E or better Unshielded or Shielded The RJ 45 Gigabit ports of the Magnum 6K16 Series can be connected to the media types 1 OOOBASE T or CAT 5E or better 100 ohm UTP or shielded twisted pai
43. ches apart with the first one located within 6 inches of the terminal block C6 0 ORDERING INFORMATION To order the optional Dual Source 48VDC power supply factory installed order Dual Src48V as a separate line item following the product model Example Magnum 6K16 SeriesR 48VDC Dual Sre 48V_ forthe regular DS model with no ON OFF switch or Dual Srce48V SWITCH with the ON OFF manual switch Pe m Similarly order the Dual source 24VDC or Dual source 125VDC as a separate line item following the product model Example Magnum 6K16 SeriesR 24VDC or Magnum 6K16 SeriesR 125VDC Dual Sre24V for regular models with no ON OFF switch Or Dual Sre125V Switch for models with the ON OFF switch C7 0 OPERATION Operation of the Dual Source Magnum 6Ks 48VDC 24VDC and 125VDC Switch models are identical to that of the standard models www GarrettCom com ss 67
44. companied by a Return Material Authorization RMA number To obtain an RMA number please use this URL https rma garrettcom com rma rma_request_noaccount php to fill out the form Please have the following information readily available Name and phone number of your contact person Name of your company institution Your shipping address Product name Serial Number or Invoice Number Packing List Number or Sales Order Number Date of installation Failure symptoms including a full description of the problem GarrettCom will carefully test and evaluate all returned products will repair products that are under warranty at no charge and will return the warranty repaired units to the sender with shipping charges prepaid see Warranty Information Appendix A for complete details However if the problem or condition causing the return cannot be duplicated by GarrettCom the unit will be returned as No Problem Found GarrettCom reserves the right to charge for the testing of non defective units under warranty Testing and repair of product that is not under warranty will result in a customer user charge 6 4 Shipping and Packaging Information Should you need to ship the unit back to GarrettCom please follow these instructions 1 Package the unit carefully It is recommended that you use the original container if available Units should be wrapped in a bubble wrap plastic sheet or bag for shipping protection You may ret
45. copper ports is to connect one of them using a fiber media converter to another Switch in the network backbone or to some other remote 100Mb device In this case it is desirable to operate the fiber link at 100Mb speed and at either half or full duplex mode depending on the capabilities of the remote device Standard commercially available Fast Ethernet media converters mostly do not support auto negotiation properly and require that the switched port to which they are connected be at 100Mb fixed speed Attachment to 10 100 auto negotiation ports typically will not work properly The 6K16 Series Switch s RJ 45 ports handle this situation by configuring the ports as per desire through MNS software port settings and can check the port status of each port after the change When Magnum 6K16 Series RJ 45 copper ports are set for auto negotiation and are connected to another auto negotiating device there are 4 different speed and F H modes possible depending on what the other device supports These are 1 100Mb full duplex 2 100Mb half duplex 3 10 Mb full duplex and 4 10 Mb half duplex The auto negotiation logic will attempt to operate in descending order and will normally arrive at the highest order mode that both devices can support at that time Since auto negotiation is potentially an externally controlled process the original highest order mode result can change at any time depending on network changes that may occur If th
46. dustrial applications where existing Ethernet LAN networks where existing cabling must be accommodated The fiber built in media capability is ideal for integrating future proof fiber cabling into the LAN structure Example 1 Magnum 6K16 Series Switch for a Industrial application Equipped with lots of useful features hardened enclosure wide spread of AC DC power supply option extended temperature rating qualifies the Magnum 6K16 Series Managed switch for any Industrial factory floors traffic control transportations systems and power utilities applications The bundles of MNS 6K software operated features diversified this managed switch to operate and perform securely and reliably in all critical applications The addition of S Ring and Link Loss Learn software feature allow this Managed switch to provide a very secure highly available redundant network capability in any ring topology network In an Industrial environment where the factory floors are networked with Ethernet based mixed media LANs equipped with PLCs computers for taking reading and data from M C Client Server databases and fetching these important datas to the central office data warehouses The Managed 6K16 Series s modularity along with MNS 6K management software features remarkably handle these kind of network very securely and reliably through out the Factory floors The DIN Rail Mounting options on the Magnum 6K 16 allow the Factory floor Industrial s user to mount
47. e Com DB 9 Port w RFE Fig 3 7 Enlarged view of Magnum 6K16 Series Console Port area Note For a detailed description of Managed Network Software MNS 6K and Magnum 6K16 Series Switch configuration for Network Management please refer to Magnum 6K16 Series Software Manual available on GarrettCom s FTP site Please refer Section 2 2 9 of this manual for download information 3 7 1 RS 232 DB 9 Console Com port Serial port pin assignments DB 9 Console port connector Pin Signal Description 1 CD Carrier detect not used 2 RXD Receive Data input 3 TXD Transmit Data output 4 open not used 5 GND Signal Ground 6 9 open not used The above information enables a management station a PC or Console terminal to connect directly to the Switch Console using a straight through serial cable _www GarrettCom con ss s s 41 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 NOTE for Power Substations Jn support of the IEEE 1613 Class 2 standard GCI advises that for substation applications the serial RJ 45console_ports are intended for temporary connectivity to other equipment such as PCs Since the console port connection is temporary it is excluded from IEEE 1613 packet loss testing per the 1613 standard defined test procedure 4 0 OPERATION This chapter describes the functions and operation of the Magnum 6K 16 Series Switch 4 1 Switching Functionality A Magnum 6
48. e chassis cover by loosening the 4 screws and bracket while holding it down firmly Figure 3 6 3a Top View 6 retaining s crews shown by arrows Step 3 Remove 6KPM Card Carefully and gently pull out the daughter board from the latching connectors using both hands gripping the board near the latch up connectors as shown in Fig 3 6 3b If the now empty slot is to remain unused be sure to install a 6KPM BLNK face plate cover Figure 3 6 3b Removing a 6KPM Card If another 6KPM card is replacing the one that has been removed follow the steps as described for installing a 6K PM card discussed in Section 3 7 1 40 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 7 Connecting a Management Console Terminal to Magnum 6K16 Series Use a DB 9 null modem cable use on any serial port or one DB 9 and one USB USB port on the laptop null modem cable to connect the Magnum6K 16 Series Console Port the RS 232 port on the 6K16 Series Switch to the your PC so that your PC becomes the 6K16 Series s Console Terminal For Hyper terminal configuration to communicate with 6K Series Switches please follow the Quick Step Guide come along with the Switch http garrettcom com techsupport software 6k25_quickstepsrel2 pdf Note A console cable either of the two types may be purchased as a separate item with the 6K16 Series unit They are not bundled with the unit Consol
49. e device at the other end is not an auto negotiating device the 6K16 Series s RJ 45 ports will try to detect its idle signal to determine 10 or 100 speed and will default to half duplex at that speed per the IEEE standard General information Auto negotiation per port for 802 3u compliant switches occurs when the devices at both ends of the cable are capable of operation at either 10Mb or 100Mb speed and or in full or half duplex mode and can send receive auto negotiation pulses and the second of the two connected devices is powered up i e when LINK is established for a port or the LINK is re established on a port after being lost temporarily 44 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 e NOTE Some NIC cards only auto negotiate when the computer system that they are in is powered up These are exceptions to the negotiate at LINK enabled rule above but may be occasionally encountered When operating in 100Mb half duplex mode cable distances and hop counts may be limited within that collision domain The Path Delay Value PDV bit times must account for all devices and cable lengths within that domain For Magnum 6K 16 Series Fast Ethernet switched ports operating at 100Mb half duplex the bit time delay is 50BT 4 5 Flow control IEEE 802 3x standard Magnum 6K 16 Series Switches incorporate a flow control mechanism for Full Duplex mode The purpose of
50. e unit and 6 screws each on the sides and 6 screws for the rear panel 2 each on top and bott0m and one each on the side Remove these screws Once these screws are removed the front panel is easily slid out to the front of the chassis base Figure 3 6 1a Removing the Front panel from the unit Caution Be careful not to disturb the power supply Once the front panel is removed the front cover may be slid out to the front of the unit Hold on the back part and then carefully and slowly slide out the top chassis cover towards the front side as shown in the picture Figure 3 6 1b Magnum 6K16 Series Top view without chassis cover _www GarettCom com ss 36 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 When the chassis top cover has been removed the interior of the unit is exposed Looking down into the Magnum 6K16 Series unit notice that there are individual PM installation spaces and female latch white connectors provided on the main board along with four stand off s for each 6KPM card position See Figure 3 6 1b above Step 3 Remove front panel face plate retaining screws There are two PM slots A B located on the front of the chassis cover Looking into the vertical placed Chassis cover of the unit there are three brackets with retaining screws 256 flat head which hold each PM Face plate card slot securely These six screws shown in the picture below are used to s
51. ecure a PM face plate in position but unscrew only four of the screws as shown in Fig below These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables See Figure 3 6 1c Figure 3 6 1c Top View 6KPM retaining screws hold Face Plate 3 6 2 Installing 6KPM Ca dsi in the Mapai 6K16 Series Up to two front mounted 6KPM cards may be installed in one Magnum 6K16 Series Managed Fiber Switch unit Follow these steps to install a 6KPM Step 1 Remove top chassis cover See procedure in Section 3 6 1 above Step 2 Placed Granddaughter board as shown in fig 3 6 2a and 3 6 2b on the chassis built in 800 IDK yoooorhHd stand off female provided at the front of the 6K 16 Series Main Board and Fig 3 6 2b Granddaughter Board placed in slot A amp secured with three 5 16 stand off s Fig 3 6 2a Granddaughter Board shown separately screw down tightly with the three 5 16 stand off male on the top of the Granddaughter board The 5 16 stand off has been used to place the daughter 37 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 board on the top of the granddaughter board and latch it securely Step 3 The figure here illustrates the basic layout of an individual PM card Each 6KPM card fits into the space provided on the main board Fig 3 6 2c Daughter Board top view of 4 copper 10 100 por
52. eft front of the unit and is equipped with three 3 screw down lead posts The power terminals are identified as positive and negative and they are floating inside the unit so that either may be grounded by the user if desired The chassis is earth or ground GND The connection procedure is straightforward Simply insert the DC leads to the Switch s power terminals positive and negative screws The use of Ground GND is optional it connects to the Switch chassis Ensure that each lead is securely tightened NOTE Always use a voltmeter to measure the voltage of the incoming power supply and figure out the ve potential lead or ve potential lead The more ve potential lead will connect to the post labeled ve and the rest to the ve The GND can be hooked up at the last When power is applied the green PWR LED will illuminate Note The GND should be hooked up first The 6K16 Series unit has a floating ground so the user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the output voltage of the power supply and determine the lead which is more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled An ON OFF manual switch is optional for DC power This can be used to cut off power connections and
53. elecommunication industry where it is common for facilities to operate on 48 VDC power Such companies include regular and wireless telephone service providers Internet Service Providers ISPs and other communication companies In addition many high availability equipment services such as broadcasters publishers newspaper operations brokerage firms and other facilities often use a battery backup system to maintain operations in the event of a power failure It is also frequently used for computer system backup management and operations monitoring equipment The 24V and 125VDC options are particularly useful in the Industrial environment where it is common for facilities to operate on 24VDC or 125VDC power The 125VDC options are mainly used in power utilities such as electrical substations electrical generating plants etc The 24VDC applications are mainly in the Industrial environment such as factory floor HVAC equipment military equipment etc The 5VDC options are mainly used for military or Industrial factory floor applications _ www GarrettCom com ss 63 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 B4 0 6K16 SERIES 48V 24 125 OR 5VDC INSTALLATION This section describes the proper connection of the 48VDC leads or 24VDC 125VDC SVDC leads to the DC power terminal block on the Magnum 6K16 Series Switch The DC terminal block on the Magnum 6K16 Series Managed Switch is located on the l
54. eo GarrettCom Industrial Networking at Its Best Magnum 6K16 Series Managed Fiber Switch Magnum 6K16V mounted vertically Hardware Installation and User Guide www GarrettCom com 5 00 USD Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 Magnum 6K16 Series Managed Fiber Switch Hardware Installation and User Guide Part 84 00136Z Rev C Trademarks GarrettCom is a registered trademark and Magnum Dymec DynaStar Personal Switch Link Loss Learn S Ring Convenient Switch and Converter Switch are trademarks of GarrettCom Inc Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories Important The Magnum 6K16 Series Managed Fiber Switch contains no user serviceable parts Attempted service by unauthorized personnel shall render all warranties null and void If problems are experienced with Magnum 6K16 Series Switch products consult Section 6 Troubleshooting of this User Guide Copyright 2006 GarrettCom Inc All rights reserved No part of this publication may be reproduced without prior written permission from GarrettCom Inc Printed in the United States of America i Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 Contacting GarrettCom Inc Please use the mailing address phone and fax numbers and email address listed below
55. ernal 48 VDC 24VDC and 125VDC Dual Source power supply are designed for installations where a battery plant is the power source and where two separate power sources are utilized in order to increase operational uptime and to simplify maintenance The functionality of the Magnum 6K16 Series Switch 48VDC 24VDC and 125VDC Dual Source Option units is identical to the standard AC powered models Refer to the main sections of this Installation and User Guide for a detailed description of the Magnum 6K 16 Series Switches C3 0 DUAL SOURCE OPTION THEORY OF OPERATION The Dual Source DC power option is designed using diodes inside of the chassis on each DC power input line A diode is placed in each of the four input lines behind the four external power connection terminals ai CHASSIS so that power from an external source can only flow into the unit This allows the unit to operate whenever DC power is correctly applied to either or both of the two inputs C4 0 FEATURES AND BENEFITS OF THE DUAL SOURCE DESIGN a The Switch unit can receive power from either input A or B The hub will normally draw its power from the DC source with the highest voltage at a given time b The Switch unit will not allow power to flow from a higher voltage input to a lower voltage input i e the two DC power sources are not mixed together by the hub c When one correct DC input is present the Switch will receive power if the other DC input
56. errupted operation of the network such as occasional multi cast packets are forwarded to all ports The Magnum 6K16 Series Switches operate in the store and forward switching mode which eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the network 42 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Address Learning All Magnum 6K 16 Series units have address table capacities of 4K node addresses suitable for use in larger networks They are self learning so as nodes are added removed or moved from one segment to another the 6K16 Series Switch automatically keeps up with node locations An address aging algorithm causes least used addresses to fall out in favor of frequently used addresses To reset the address buffer cycle power down and up 4 2 Status LEDs For Magnum 6K16 Series models 6K16 6K16V PWR Power LED ON when external power is applied to the unit LK Steady ON Link status for 10 Mbps and 100Mbps operation ACT ON with port activity for 10 Mbps and 100Mbps operation F H Full Half duplex LED ON when the port is running full duplex OFF for half duplex 100 10 Speed LED ON when the speed is 100Mbps OFF when the speed is 10 Mbps 4 3 Up link Manual Switches set as for RJ 45 port only The module has a manual Up link switch located on the inside of the board next to the 10 100Mb 6KP8 RJ45 port 1 which it control
57. for use in a factory floor industrial environment It is available with optional DIN Rail brackets to mount it securely in a metal factory floor enclosure maintained vertically for proper convection cooling of the unit The Magnum 6K16V requires two DIN Rail mounting clips or latches for secure mounting and these may be ordered as Model DIN RAIL VRM is j lt i See a 6K16V viewed from the rear at right with model DIN RAIL VRM in places on ihe unit 30 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The Din Rail Latching clips are mounted on the upper rear corners of the 6K16V unit Two threaded holes are provided on the sides of 6K16V for DIN Rail mounting purposes See side view at the left with the top of the unit pointed to the right The required two screws are included with the DIN Rail brackets and are no 10 32 X 3 8 PHIL PAN w star washer The two heavy duty Din Rail latches are designed as if that they can be manually accessed from the top when the 6K16V is installed on a DIN Rail To install the 6K16V with the DIN Rail brackets and latches attached to it hold the 6K16V in the vertical position with the bottom out and with the top moved in toward the DIN Rail Position the latches over the top of the DIN Rail Then snap the latches into holding position by moving the bottom of the 6K16V inwards to a vertical position The DIN Rail latches and brackets are heavy duty and will hold
58. gh performance features include non blocking speed on all ports and 802 1p QoS Traffic Prioritization Magnum 6K16 Series switches are plug and play ready for use as backbone switches where a mix of bursty data traffic and priority streaming traffic for VoIP and audio video Triple Play applications are present Magnum 6K 16 Series Fiber Switches are provided with LAN management _www GarrettCom con ss lt lt s ss 9 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 software including SNMP Tag and Port based VLANs IGMP Snooping and Port Security with control via Web and command line interface CLI For high availability LANs using ring topologies Spanning Tree Protocol Link Loss Learn and S Ring are available See the Managed Networks Software MNS 6K and S Ring datasheets for additional details on the comprehensive set of software programs and options Magnum 6K16 Series Managed Fiber Switches have heavy duty metal cases and auto ranging power supplies for operation with standard AC power worldwide Internal DC power supplies are optional All DC power input types 5V 24V 48V 125V are supported and dual source input is optional on all except SVDC Alarm Relay contacts provided on each Magnum 6K16 Series Switch monitor the hardware and software providing a loss of power signal and user defined software events through traps See Section 3 5 for details The wide selections of port modules
59. h jobs are readily accommodated with an extended temperature rating of 40 C to 60 C by the UL Component Parts method or 50 C to 95 C by the IEC 60068 Type Test method With options such as all popular DC power input types worldwide AC power and DIN Rail mounting the hardened Magnum 6K 16 Series is a multi purpose Industrial Ethernet Switch The large family of port modules offer the choice of all fiber media all connector types multi and single mode and 10 100 Mb auto negotiating RJ 45 ports Standard GBIC ports can be configured for a variety of Gigabit cabling types and distances The 6K16 Series managed switches also provides PoE option via power inside PoE modules on one of A or B slot and allows the users to select a wide option of combo PoE modules to support 802 3af pd devices See details for PoE modules in sec 5 2 10 The Power Sourcing Equipment PSE and are fully compatible with Powered Devices PD e g wireless access points IP phones that comply with the IEEE 802 3af PoE standard The PoE switch ports have an auto sensing algorithm so that they provide power only to 802 3af PoE end devices PoE is managed by a multi stage handshake to protect equipment from damage and to manage power budgets The PoE ports will discontinue supplying power when the PoE powered devices are disconnected and support the 802 3af PoE PSE standard for over current protection under current detection and fault protection Hi
60. ion Note The GND should be hooked up first The 6K16 Series unit has a floating ground so the user may elect to Ground either or terminal to suit the customer s use Before connecting hot lines to the Terminal Block of 48VDC 24VDC or 125VDC always use a digital voltmeter to measure the output voltage of the power supply and determine the lead whichis more ve potential The more ve voltage lead from 48V or 48V supply must be connected to the post labeled The connection procedure is straightforward Simply connect the DC leads to the Switch s power terminals positive and negative screws The use of Ground GND is optional it connects to the Switch chassis Ensure that each lead is securely tightened The 24VDC amp 125VDC terminal block on Magnum 6K 16 Series s is similar to that described in the 48VDC information above C5 1 UL Requirements The following must be adhered to in order to conform to UL requirements Minimum 18 AWG cable for connection to a Centralized DC power source Minimum 14 AWG cable for connection to earthing wiring Use only with Listed 10 A circuit breaker provided in building installation Complies with FDA radiation performance standards 21 CFR subchapter J or equivalent Fastening torque of the lugs on the terminal block 9 inch pound max 6 Centralized DC Power Source cable securement use at least four cable ties to secure the cable to the rack at least 4 in
61. ions The Multi media copper and fiber support loaded with rich management feature of MNS 6K easily qualified this carrier class switch to meet any demands and requirement of this space Magnum 6K management features not only allow the easy monitoring of the switch through SNMP but also protect the network through its security features of port security SNMP3 VLAN etc The redundant feature through STP RSTP and S ring LLL also allow to configure and control the switch as a fault tolerant device or self healing in a ring topology applications The NEBS and ETSI compliant Magnum 6K 16 rack mountable and specially designed to support the popular DC options of 24VDC 48VDC AND 125VDC as well as AC input easily qualify and make a popular and reliable contender for the carrier class Telco and factory floor applications The rich choice of modules in various flavors of all fiber connectors multi or single mode combo of copper and fiber and a diversification option to select 10Mb fiber or 100Mb copper or 1000Mb copper Fiber are some of the primary benefits which allow the Magnum 6K 16 to fulfill all the demands and requirements of carrier class office and factory floor applications The Relay contacts for external ALARM is another additional feature which allow the Magnum 6K 16 to monitor the internal power failure and controlled via hardware or software traps 12 Magnum 6K16 Series Managed Fiber Switch Installation and
62. is absent or even if it is connected with reverse polarity or shorted or grounded d Reverse polarity connections if they should accidentally occur on either input will not damage the Switch or power supply internally nor will it blow the fuse in the internal power supply because of the blocking action of the diodes This is true even if one input connection is reversed while the Switch is operating from the other source e The Switch will not receive power and will not work when both inputs are simultaneously absent or are both incorrectly connected DC terminal block C5 0 INSTALLATION This section describes the proper connection of the 48VDC 24VDC and 125VDC dual source leads to the 48VDC 24VDC amp 125VDC power terminal block on the Magnum 6Ks Switch shown in Figure 66 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The 48VDC terminal block on the Magnum 6K16 Series Switch as shown in Fig C5 0 is located on the left front of the unit and is equipped with five 5 screw down lead posts The primary terminals are identified as positive A negative A and the secondary power terminals as negative B positive B The chassis earth or ground GND is a threaded post with a 6 nut The Dual Source terminal block for the 24VDC and 125VDC are similar Figure C5 0 48VDC Dual Source wiring connections to the External Terminal Block on a Magnum 48VDC with Dual Source opt
63. l RJ 45 Ports Input Voltage SVDC or 5 SVDC Input current 3 5Amps max for all RJ 45 ports Input current 8 0Amps max for all Fiber ports Power Consumption 20 watts max for fully loaded fiber ports 17 watts typical for all RJ 45 Ports B2 0 48VDC 24VDC and 125VDC POWER THEORY OF OPERATION The 48VDC 24VDC and 125VDC power options are designed using diodes inside on each DC power input line POWER SWITCH aor behind the two external power connection SUPPLY terminals so that the power from an ae external source can only flow into the ia hub This allows the Switch to operate en GND only whenever DC power is correctly applied to the two inputs It protects the Switch from incorrect DC input connections An incorrect polarity connection for example will neither affect the Switch its internal power supply nor will it blow the fuse in the internal power supply The manual power On Off Switch optional is used for powering the unit on and off when it is placed into or taken out of service B3 0 APPLICATIONS FOR DC POWERED ETHERNET SWITCHES Magnum 6K 16 Series Switches are easily installed in a variety of applications where 48VDC 24 or 125VDC or 5VDC power is used as the primary power source The DC power configuration capability provides an Ethernet networking solution utilizing a special power supply in switches with a proven track record The 48 VDC solution is particularly useful in the t
64. l mounting brackets to the case Can add Model K16 EXTN KIT to extend to ETSI and 23 rack width K16 2TRAY Rack mount tray fro holding two side by side 6K16 s in a 19 1 5U rack space each 6K16 unit individually removable for service Can add Model K16 EXTN KIT to extend to ETSI and 23 rack width K16 EXTN KIT Kit of extender brackets for converting one K16 RMB or one K16 2TRAY to ETSI and or to 23 Telco rack The above mentioned rack mount kits is being designed for Magnum 6K 16 only to provide the rack mount support to the carrier class switch and filled the 19 RETMA 1U rack space The K16 EXTN KIT is specially designed to meet the European Telco Standard ETSI 23 Telco rack requirement Fig 3 3 2a One Magnum 6K16 deployed over a K16 2Tray The pro carrier class Switch Magnum 6K16 can be installed single as it is being shown on the above Fig 3 4a on the K16 2Tray The empty slot on K16 2Tray can be filled as per the requirement Easy to install the K16 2Tray comes along with all the accessories to install securely and quickly The 6K16 Switches are being installed side by side to provide a larger port density is shown below in Fig 3 4b tnt oT TO uma o Fig 3 3 2b Two Magnum 6K16s deployed over a K16 2Tray side by side to provide larger port density of 32 ports 33 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 4 Powering the Magnum 6K16 Series Managed Fiber
65. le loss LED aging loss Insertion loss safety factor 5 0 Introduction Magnum 6K16 6K16V Managed Fiber Switch Port Modules This chapter describes each Port Module PM including appearance functionality and status displays 5 1 Inspecting the Package and Product This section applies only to PMs shipped as separate items i e 6K 16 6K16V PMs not factory installed in a Magnum 6K16 6K16V PM slot Examine the shipping container for obvious damage prior to installing a 6K16 6K16V PM notify the carrier of any damage you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included This package should contain 1 or more 6K16 Series 6K16 or 6K16V PMs Installation instructions with illustrations Remove the 6K16 Series PM s from the shipping container Be sure to keep the shipping container should you need to ship any of the PMs separately at a later date In the event there are items missing or damaged contact your supplier If you need to return the unit use the original shipping container if possible Refer to Chapter 5 for specific return procedures 5 2 6KPM Module Description An important feature of the Magnum 6K 16 Series is the use of Port Modules for flexible mixed media connectivity to RJ 45 and fiber media Since the Magnum 6K16 Series Switches have dual speed capability for copper ports the 2 4 6 or 8 port interfaces
66. lex and 412m at half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed if the LED is ON 100Mbps if it is OFF 10Mbps 5 2 la 6KP6 RJ10ST 4 10 100Mbps RJ 45 and 2 10Mb multi mode FX ST twist lock Combo Module The 6KP6 RJ1OST is a six port combo module that looks similar to the 100Mb combo module with the exception of 10Mb speed at the ST fiber module The ST connector functions as a fiber optic transceiver to support 1 OBASE FX network segments When installed in a Magnum 6K16 Series Managed Switch the copper port supports the standard distance 100m on each port and the fiber port supports fiber optic _www GarrettCom com ge 48 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 cable distances up the IEEE standard 10Mbps distance limits i e typically 2km at full duplex and half duplex Each port has an Activity ACT LED indicating packets being received a Link LK LED that indicates proper connectivity with the remote device when lit and FDX HDX LED to indicate full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed if the LED is ON 100Mbps if it is OFF 1OMbps 5 2 1b 6KP4 F10ST 4 10Mb multi mode FX ST twist lock Module 6KP4 RJLOMS
67. llow the suggestions listed below prior to contacting your supplier However if you are unsure of the procedures described in this section or if the Magnum 6K16 Series Switch is not performing as expected do not attempt to repair the unit instead contact your supplier for assistance or contact GarrettCom Customer Support _ www GarrettCom com ss s amp s se 59 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 6 1 Before Calling for Assistance l If difficulty is encountered when installing or operating the unit refer back to the Installation Section of the applicable chapter of this manual Also check to make sure that the various components of the network are interoperable 2 Check the cables and connectors to ensure that they have been properly connected and the cables wires have not been crimped or in some way impaired during installation About 90 of network downtime can be attributed to wiring and connector problems 3 Make sure that an AC power cord is properly attached to each Magnum 6K16 Series Switch unit Be certain that each AC power cord is plugged into a functioning electrical outlet Use the PWR LEDs to verify each unit is receiving power 4 If the problem is isolated to a network device other than the Magnum 6K16 Series Switch product it is recommended that the problem device be replaced with a known good device Verify whether or not the problem is corrected If not go to Step
68. n and User Guide 03 09 On the model 6KP8 RJ45 module there are four LEDs for each port two in the connector and two separate The LK Link LED indicates ready for operation on that port when lit The blinking ACT Activity LED indicates receiving Activity on that port when lit The 10 100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF when auto negotiation is not disabled The FDX HDX LED is ON to indicate full duplex operation and OFF to indicate half duplex mode A twisted pair cable must be connected into an RJ 45 port and the Link LK indicator for that port must be ON indicating there is a powered up device at the other end of the cable in order for a LK LED to provide valid indications of operating conditions on that port Using the 6K 16 Series MNS 6K management software the user may disable auto negotiation and fix the desired operation of each RJ 45 port User may select 1OMb or LOOMb speed and full or half duplex mode per port as per user requirement See Magnum MNS 6K Software Manual for details info 2 2 4 PoE Power Pass through P6KP8 RJ45 10 100Mb 8 port The PoE Power pass through RJ 45 ports act similar to regular RJ 45 ports except they have capability of providing power on each port to power up the PD devices 6KP8 45RJ per the IEEE802 3af PoE standard The Power Pass through PoE modules are totally dependent upon the powerful 48VDC input power supply to su
69. ndard The Power 8 Port 10 100Mb Copper ports Pass through PoE modules are totally dependent upon the powerful 48VDC input power supply to support more RJ 45 10 100 ports Each port require atleast 15watts to power up the PoE PD devices In this Fig the top 8 RJ45 ports are enhanced with POE option The 8 RJ45 POE module are also available with mix n match with fiber modules Please check the ordering information Sec 1 2 for all the various P6K PoE modules option The LEDs on 6KP8 RJ45 PoE module are slightly different compared to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram PoE LEDs Summary e For PoE devices each RJ 45 PoE port supports only 802 3af complaint devices The PoE LED is ON when the attached PD is drawing power from the port 6KP8 45 2MT e For non PoE devices 6 Port 10 10Mbps amp 2 port 100Mb connected the PoE port will Multi Mode F CoS act as a normal RJ 45 port and the PoE LED is OFF No power is being sent out from the port e The PoE ports in Magnum 6K s with 48VDC power input act as a pass through so the 48VDC power source 10 100 L
70. ng 6K16V Horizontal Rack mount 2 units side by side on 19 or 21 rack 6K16 Agency Approvals and Standard Compliance Magnum 6K16V UL listed UL60950 cUL CE Emissions meet FCC Part 15 Class A NEBS Level 3 and ETSI Compliant IEEE 1613 Environmental Standard for Electric Power Substations See also Note for Power Substations in Section 3 2 4 3 7 and 5 2 9 IEC 61850 EMC and Operating Conditions Class C for Power Substations NEMA TS 2 and TEES for traffic control equipment Magnum 6K16 UL listed UL60950 cUL CE Emissions meet FCC Part 15 Class B IEEE 1613 Class 2 Environmental Standard for Electric Power Substations See also Note for Power Substations in Section 3 2 4 3 7 and 5 2 9 IEC 61850 EMC and Operating Conditions Class C for Power Substations NEBS Level 3 and ETSI Compliant NEMA TS 2 and TEES for traffic control equipment Warranty Three years per UL 60950 temperature rating Made in USA Email sales GarrettCom com for details Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 1 2 Ordering Information Magnum Managed Fiber Switch 16 ports max MODEL DESCRIPTION Magnum 6K16V Magnum 6K16V Managed Fiber Switch base unit for vertical mounting Worldwide AC power May be configured with a selection of 10 100 1000 fiber and copper port connector types 16 total ports max Two metal brackets for vertical wall or panel mounting Wire speed filtering and forwarding across all ports 802 3x fl
71. ng received a Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 10Mbps when the LED is ON and 10 Mb when the LED is OFF 5 2 5 6KP8 MTRJ 8 100Mb multi mode FX MTRJ Small Form factor Magnum 6KP8 MTRJ is a multi mode fiber optic 8 port module equipped with a small form factor MTRJ type 6KP8 MTRJ cmall form factor 8 Port 100Mbps Multi Mode Fiber port connector It looks almost like an RJ 45 port but it is black in color The MT RJ s small size and ease of connection make it 1 3 s 7 a good choice for 100Mbps L L Cl CJ Al fiber to the desktop Ethernet A FIC RIE L E 1k D xl AC connectivity When installed in a Magnum 6K16 Series Switch activity 2 it supports fiber optic cable O FULL HALF distances up the IEEE standard LINK 100Mbps distance limits i e 52 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 typically 2km at full duplex and 412m at half duplex The functionality of this 1OOBASE FX multi mode 8 Port module is essentially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 5a 6KP6 MTIOST 4 100Mb multi mode FX MTRJ Small Form Factor and 2 10Mb Multi mode ST Fiber
72. nput panel in the Magnum 6K16 s case The AC or DC power input connection is in the same panel A manual On Off Switch for power to the unit is not available on 6K16 units with the Alarm Contacts option as these two features occupy the same space in the case The first NC Alarm Contact top position is a Software Alarm operated by user settings in the MNS 6K software The user can disable the Software Alarm feature with a software configuration command if desired When the Software Alarm is enabled the Form C Normally Closed NC contact is held close during normal software operation A user defined software malfunction such as an SNMP Trap or a Software Security violation or an S Ring Fault causes the contact to open and thus trigger an alarm in the user s monitoring system The second bottom position NC Alarm Contact is held close when there is power on the main board inside of the 6K16 This provides a Hardware Alarm because 34 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 the NC contacts will open when internal power is lost either from an external power down condition or by the failure of the power supply inside of the Magnum 6K16 Switch Useful info about Alarm contacts 1 There is four terminal block 1 2 3 4 provided next to AC DC power supply 2 The top two pins 1 2 are software operated 3 The bottom two pins 3 4 are hardware operated 4 By default it is NC no
73. num 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The 1000Mb Gigabit fiber port modules on the Magnum 6K 16 Series are normally set factory default to operate at AUTO mode for best fiber distance and performance The 1000Mbps SC fiber optic module on the Gigabit SX and Gigabit LX transceivers are compatible with the IEEE 802 3z Gigabit standards There are two LEDs mounted on each Gigabit port module The Gigabit fiber has LEDs that indicate LK Link status and ACT receiving activity on that port when lit 2 2 7a GBPM 20TX Two Gigabit module option The Magnum 6K16 Series offered a wide selection of Gigabit speed with multiple choice of copper or Fiber or mix for the modular slot via GBPM 20TX module While up to two Gigabit modules maxm can be configured in the modular slot for GBPM 2OTX The Dual Gigabit port option for the modular slot come in couple of different configuration to provide a wide option of choice of various Gigabit transceivers covering a long range of distance The GBPM 20TX also meets the requirement for those applications where a managed Gigabit media converter is required The two Gigabit slot can be filled with copper Fiber or mix as per the application 18 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Model GBIC Description One 1000BASE SX GBIC SXSC port with multi mode SC fiber connector One 1000BASE LX LH GBIC LXSC10 port 1310nm
74. oe oree terra otc te reer tyr creeserr rear tre care 30 3 2 6 Connecting Gigabit Media Using GBICs eeceeeesseeteeeees 30 3 3 DIN Rail Mounting Magnum 6K 16V ccceecceeceseceteceeeseeeeeeaes 30 3 3 1 Mounting Dimensions for 6K16Vwith metal brackets 32 3 3 2 Rack mounting Magnum 6K16 for Telco and ETSI Standard 33 3 4 Powering the Magnum 6K16 Series Managed Fiber Switch 34 3 5 Alarm Contacts for monitoring internal power Software Traps 34 3 6 6K16 Series Port Module 6KPM Installation ccc eeeeeeeteeeees 35 3 6 1 Preparation for Installing and Removing 6KPMS ceeee 35 3 6 2 Installing 6KPM Cards in the Magnum 6K 16 Series 37 3 6 3 Removing 6KPM Cards c ccccesseessceseceseceeeceeeeeeeseeseeeseeeereees 40 3 7 Connecting a Management Console Terminal to 6K 16 Series 41 iv Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 3 7 1 RS 232 DB 9 Console port Serial port pin assignments 41 4 0 OPERATION sareen aiin E EN 42 4 1 Switching Functionality s seseeseneeeseeeesseeesseeessstsresseserseseesesseeeesse 42 AD SAMS LEEDS cosets cass e N aE E a 43 4 3 Up link Manual Switches set as for RJ 45 port only 43 4 4 Auto Cross MDIX and Auto negotiation for RJ 45 ports 43 4 5 Flow control IEEE 802 3x standard cccccccsscesscessseceeeeecseceeeeees 45 4 6
75. oid the warranty Caution Avoid Static Discharge The port modules like most electronic equipment are sensitive to static discharge Use proper ESD measures when handling port modules 35 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Step 1 Make sure the 6KPM Card package has all necessary accessories to install it properly Each 6KPM Card package except the Gigabit for field installation contains Daughterboard Bigger and Granddaughter board smaller three 5 8 stand offs for Granddaughter board 6 standoff for daughter Board nine 4 40 Pan Head screws along with Front panel face plate package The Front panel faceplate package includes 2 retainer brackets and four 2 56 flat head screws NOTE Every 6KPM Card package comes with their matching Daughter and Granddaughter board The copper 6KPM card should not work properly if mixed with other Fiber combo 6KPM card packages Always install the PM module separately one by one to avoid the mixing Do not change the Blue color DIP Switch setting ever and leave it at factory default Step 2 Remove Chassis Cover The Magnum 6K16 Series chassis consists of top bottom front and rear parts and assembled together with the help of 18 Philips head screws There are 6 screws located on the front panel of the A PEA unit 2 each on top and the bottom and a one each at the side 12 for top bottom fe A Wily cover of the unit 6 each on the bottom side of th
76. one OQ LINK 10 100 module The 6K P8 45 2SLC is equipped ACTIVITY Oua HALF with 6 10 100 RJ 45 ports and 2 Single mode fiber ports When installed in a Magnum 6K16 Series Switch it supports the standard distances as mentioned on 5 2 4 and the LEDs also act similarly 5 2 13 GBIC SXSC Gigabit fiber 1000Mb multi mode SC Connector The Magnum GBIC SXSC is a multi mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the IEEE 802 3z standard 1000Mbps distance limits i e 550m at full duplex 1 1000Mb Fiber SC 4 10 100Mb 57 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The GBIC transceiver has been offered in the modular slot with multiple options as per the user requirement The two Giga port has been offered as GBPM 2OTX fiber or RJ 45 whereas the single Gigabit module comes in two different flavor of G 2 100Mb fiber ports or G 4 10 100 RJ 45 ports as shown in the above figure The GBIC transceiver is fastened using snap in clips Insert the transceiver take care to insert it the right way up arrows on top until it clicks in space While removing the transceiver press the clips on either side of the transceiver at the same time and pull the transceiver out Each port has an Activity ACT LED indicating
77. ons for single mode 50 125 or 62 5 125 microns for multi mode where xx xx are the diameters of the core and the core plus the cladding respectively Single mode fiber allows full bandwidth at longer distances and may be used to connect 10 Mb nodes up to 10 Km apart or 18Km with the 6K SSC The same procedures as for multi mode fiber applies to single mode fiber connectors Follow the steps listed in Section 3 2 2 above 3 2 4 Connecting Twisted Pair RJ 45 CAT3 CATS Unshielded or Shielded The RJ 45 ports of the Magnum 6K16 Series can be connected to the following two media types 1 OOBASE TX and 1OBASE T CAT 5 cables should be used when making 100BASE TX connections When the ports are used as 1OBASE T ports CAT 3 may be used In either case the maximum distance for unshielded twisted pair cabling is 100 meters 328 ft Media IEEE Standard Connector Twisted Pair CAT 3 4 5 10BASE T RJ 45 Twisted Pair CAT 5 100BASE TX RJ 45 NOTE Jt is recommended that high quality CAT 5 cables which work for both 10 Mb and 100Mb be used whenever possible in order to provide flexibility in a mixed speed network since dual speed ports are auto sensing for either 10 and 100Mb s The following procedure describes how to connect a 10BASE T or 100BASE TX twisted pair segment to the RJ 45 port The procedure is the same for both unshielded and shielded twisted pair cables 1 Using standard twisted pair media insert either end of the ca
78. ow control sequence occurs in a small fraction of a second and is transparent to an observer Another feature implemented in Magnum 6K16 Series Switches is a collision based flow control mechanism when operating at half duplex only When the Switch detects that its free buffer queue space is low the Switch prevents more frames from entering by forcing a collision signal on all receiving half duplex ports in order to stop incoming traffic 2 2 10 Managed Network Software MNS 6K Magnum 6K16 Series s come with licensed MNS 6K Firmware Rel 3 2 which allows to configure the Magnum 6Ks as a Managed Switch and other Software enabled features For additional information about MNS 6K see the Magnum 6K16 Series MNS Software User guide in pdf format a separate document normally accessed via your web browser at ftp ftp garrettcom com or FTP client program by ftp GarrettCom com using user m6kuser password m6kuser _www GarettCom con i as 20 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 All MNS 6K software information including new releases and upgrades related to MNS 6K software can be accessed and download from GarrettCom s FTP site Alternatively for documentation and latest information or needed GarrettCom proprietary MIBs for SNMP www GarrettCom com techsupport index htm software and look for Magnum MNS 6K info Magnum MNS 6K Operator Training This interactive training software
79. ow control 802 1p priority packet processing self learning 4K node address table large 240KB packet buffers for 10 100 and 120KB for 1000Mb For licensed managed networks software MNS 6K and S ring See separate data sheets Magnum 6K16V 24VDC Same as 6K16V except the power input is 24VDC Magnum 6K16V 5VDC Same as 6K16V except the power input is SVDC reg amp fused Magnum 6K16V 48VDC Same as 6K16V except the power input is 48VDC Magnum 6K16V 125VDC Same as 6K16V except the power input is 125VDC Configuration Options Each Magnum 6K16V base unit has TWO port module slots Magnum 6K16V Port Modules 6KP8V MTRJ SFF Fiber module w eight 100Mb mm FX MT RJ connectors 6KP8V MLC SFF Fiber module w eight 100Mbps mm FX LC connectors 6KP8V SLC SFF Fiber module w eight 100Mbps sgl m FX LC connectors 6KP4V FXSC 2 2 100Mb Fiber module w four 100Mb 2km FX SC connectors 6KP4V FXST 2 2 100Mb Fiber module w four 100Mb 2km FX ST connectors 6KP4V FIOST 2 2 10Mb Fiber module w four 10Mb 2km FL ST connectors 6KP4V FLSTFX 2 2 ST Fiber module w two 100Mb amp two 10Mb ports 2km 6KP8V 45 2MT 6 2 module w six RJ 45 ports and two 100Mb 2km FX MTRJ s 6KP8V 45 2LC 6 2 module w six RJ 45 ports and two 100Mb 2km FX LC 6KP8V RJ45 TP Module w eight 10 100Mbps auto negotiating RJ 45 ports 6KP8V 45MT 4 4 module w four RJ 45 ports and four 2km mm FX MT RJ s 6KP8V 45MLC 4 4 module w four RJ 45 po
80. p with the traffic flow 4 6 Power Budget Calculations for Magnum 6K16 Series PM s with Fiber Media Receiver Sensitivity and Transmitter Power are the parameters necessary to compute the power budget To calculate the power budget of different fiber media installations using Magnum products the following equations should be used OPB Optical Power Budget P min Pr min _ www GarrettCom com ss 45 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 where P Transmitter Output Power and Pg Receiver Sensitivity Worst case OPB OPB 1dB for LED aging 1dB for insertion loss Worst case distance Worst case OPB in dB Cable Loss in dB Km where the Cable Loss for 62 5 125 and 50 125um M m is 2 8 dB km and the Cable Loss for 100 140 Multi mode is 3 3 dB km and the Cable Loss for 9 125 Single mode is 0 5 dB km and the Cable Loss for 9 125 Single mode is 0 4 dB km LXSC25 and the Cable Loss for 9 125 Single mode is 0 25 dB km LXSC40 and the Cable Loss for 9 125 Single mode is 0 2 dB km LXSC70 The following data has been collected from component manufacturer s Agilent s and Lucent web sites and es to provide guidance to network designers and installers Fiber Speed Port Module Std Mode nas 6KP4V 10Mb Multi 850 162 F10ST FL Mode a 19 5 5 9 23 5 19 5 3 4 13 5 6KPV 100Mb Multi 62 5 125 20 31 9 0
81. pace for air movement around the top and the sides typically a minimum of 1 inch Note that the back of the 6K16V unit is held out from the panel or wall behind it creating a rear space of about inch or 1cm This allows air circulation and cooling of the rear part of the case Since the 6K16V uses special internal thermal techniques patent pending to move the heat generated by the electronic components inside into the case the case may be quite warm to the touch during normal operation G ONLY USE SCREW IDED WITH THE UNIT TI T BRACKET T CT The unit can be mounted using the brackets turned outside normal or inside if space is tight Attach the mounting bracket either outside or inside as shown in the illustration above dotted line shown for the brackets inside The spacing for the mounting screws into the supporting wall or panel is a rectangle 11 89 x 7 85 center to center www GarrettCom com 32 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 3 2 Rack mounting Magnum 6K16 for Telco and ETSI Standard Magnum 6K 16 a carrier class focused managed switch can be mounted as rack mount using the following kit options offered for this product K16 RMB Set of two rack mount brackets for one 6K16 unit in a 19 RETMA 1U rack space with screws to attach the meta
82. packets being received and a Link LK LED indicating proper connectivity with the remote device when lit 5 2 13a GBIC LXSC Gigabit fiber 1000Mb multi mode SC Connector The Magnum GBIC LXSC is a single mode Gigabit fiber connector equipped with SC type connectors and can be easily snapped in and out The Gigabit fiber ports are most popular as server to switch and switch to switch applications It supports cable distances up to the IEEE 802 3z standard 1000Mbps distance limits i e 10 25 40 or 70Km at full duplex and depend upon the Gigabit modules used 1 1000Mb Fiber SC 2 100Mb SC The two Giga port has been offered as GBPM 2O0TX fiber or RJ 45 whereas the single Gigabit module comes in flavors of G 4 10 100 RJ 45 ports or G 2 100Mb fiber ports as shown below in the above figure Each port has an Activity ACT LED indicating packets being received and a link LK LED indicating proper connectivity with the remote device when lit Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 5 2 14 GBPM 20TX Two Gigabit option The Magnum 6K16 Series offered a wide selection of Gigabit speed with multiple choice of copper or Fiber or mix for the modular slot via GBPM 2OTX 2 x Giga module While up to two Gigabit modules maxm can be configured in the modular slot for GBPM 2OTX The Dual Gigabit port option for the modular slot provides a wide variety of choices for various Gigabit
83. port The 6KP6 RJ10ST is a combo module with two different kinds of fiber flavor with two different speeds The top four ports of MTRJ Small form factor fiber support at 100Mb full duplex whereas the bottom two ports multi mode ST Fiber support 1OMb half duplex This combo module provides more flexibility to the user to connect their legacy 10Mb fiber as well as 100Mb to the Magnum 6K16 Series Switch When installed in a Magnum 6K16 Series Switch the 100Mb MTRJ connector supports fiber optic cable distances up to the IEEE standard 100Mbps distance limits i e typically 2km at full duplex and 412m at half duplex The 10Mb Multi mode ST Fiber connector supports the standard fiber optic distance limit of 2Km at Full and Half duplex both The functionality of this 1OOBASE FX multi mode 4 port module is essentially the same as the ST and SC types It has the same LEDs per port indicating port activity ACT Link LK and FDX or HDX operation 5 2 6 6KP8 45MT 4 10 100Mbps RJ 45 and 4 100Mb multi mode FX MTRJ Small Form Factor The Magnum 6KP8 45MT 6KP8 45MT 4 Port 10 100Mbps amp 4 port 100Mbps Multi Mode yOu Module is a combo module with copper and fiber Small Form Factor MTRJ type ports The small size of MTRJ connectors provides an advantage of placing more ports on one module The 6KP8 45MT is equipped with 4 10 100 RJ 45 ports and 4 MTRJ fiber ports O LINK D 10 100 When installed in a Magnum 6K16 ACTIVITY Q
84. pport more RJ 45 10 100 ports Each port requires atleast 15watts to power up the PoE PD devices Maxm one PoE modules can be configured in the A B slot of any 6K16 s with 48vdc power input The PoE modules are also available with mix n match with fiber modules Please check the ordering information Sec 1 2 for all the various P6K PoE modules option 8 Port 10 100Mb Copper ports 15 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 The LEDs on 6KP8 RJ45 PoE module are slightly different compared to regular non PoE RJ 45 modules as shown in Fig 2 When the PoE port is in use the PoE LED is ON when connected properly to a 803 af compliant PD device on that port When non PoE devices are connected the PoE LED is OFF Operation of Ethernet data traffic is not affected by PoE LINK and ACTIVITY LEDS are combined on the PoE modules into one LED that is marked as LINK ACT as shown in the diagram 2 2 5 6 Port 4 2 Combo Modules 4 10 100 RJ 45 and 2 100Mb fiber The combo six port modules are combinations of copper and fiber media available as four 10 100 switched RJ 45 copper ports and two 100Mb switched multi mode fiber ST 5 T Pr cr SC or single mode SC or Long Reach SC ports For ports numbering ports 1 3 5 7 are copper ports 2 and 6 are fiber ports 4 and 8 are not present The four RJ 45 ports operate just like the 8 port copper module with auto cross MDIX fea
85. r STP balanced cable The CAT 5E or better 100 ohm UTP or shielded twisted pair STP balanced cable is recommended to use when making 1000BASE TX connections In either case the max distance for unshielded twisted pair cabling is 100 meters 328 ft Media IEEE Standard Connector Twisted Pair CAT 5E 1000BASE T RJ 45 NOTE It is recommended that high quality CAT 5E cables which work for both 100 Mb and 1000Mb be used whenever possible in order to provide flexibility in a mixed speed network The following procedure describes how to connect a 1000BASE T twisted pair segment to the RJ 45 port The procedure is the same for both unshielded and shielded twisted pair cables 1 1000Base T connections require that all four pairs or wires be connected Insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the port Note that even though the connector is shielded either unshielded or shielded cables and wiring may be used 2 Connect the other end of the cable to the corresponding device 3 Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established 3 2 6 Connecting Gigabit Media Using GBICs The Gigabit ports accept industry standard GBICs for user selection of the gigabit media type desired A selection of fiber and copper GBICs are available 3 3 DIN Rail Mounting Magnum 6K16V The Magnum 6K16V is designed
86. ransceiver module K16 RMB Set of two rack mount brackets for one 6K16 unit in a 19 RETMA 1U rack space with screws to attach the metal mounting brackets to the case Can add Model K16 EXTN KIT to extend to ETSI and 23 rack width K16 2TRAY Rack mount tray fro holding two side by side 6K16 s in a 19 1 5U rack space each 6K16 unit individually removable for service Can add Model K16 EXTN KIT to extend to ETSI and 23 rack width K16 EXTN KIT Kit of extender brackets for converting one K16 RMB or one K16 2TRAY to ETSI and or to 23 Telco rack Gigabit 1000Mb Transceivers option for Mangum 6K16 Series 6K16V 6K16 GBIC SXSC GBIC transceiver module for use in GBPM xOTX one 1000BASE SX port with mm SC fiber connector GBIC LXSC10_ GBIC transceiver module for use in GBPM xOTX one 1000BASE LX LH port with 1310nm sgl mode SC 10km fiber connector GBIC LXSC25_ GBIC transceiver module for use in GBPM xOTX one 1000BASE LX LH port with 1310nm sgl mode SC 25km fiber connector GBIC ZXSC40_ GBIC transceiver module for use in GBPM xOTX one 1000BASE ZX port with 1550nm sgl mode SC 40km fiber connector GBIC transceiver module for use in GBPM COTX one LX port with mm SC fiber connector GBIC ZXSC70_ GBIC transceiver module for use in GBPM xOTX one 1000BASE ZX port with 1550nm sgl mode SC 70km fiber connector GBIC TP GBIC transceiver module for use in GBPM xOTX one 802 3ab 1000BASE T port RJ 45 connector CONSOLE CB
87. rity features e g port security vlan Snmpv3 secure telnet etc also boost the Magnum 6K16 managed switches to provide a very effective ad reliable solution The modularity feature to support both copper and fiber at either 10 100 1000Mb speed easily meet the variation speed of legacy and future broadband requirement In a carrier class Telco environment the expected reliable and secure solution can be met easily by Magnum 6K 16s managed switches He modular design of Magnum 6K 16 provide a wide range of options of copper fiber and both configuration to meet heir requirement The Gigabit uplink for the storage or broadband uplink allows the telecom users a very effective solution to store their sensitive users data securely Fig 2 4c Magnum 6K16s deployed in a Telco environment for storing the carriers data 26 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 0 Installation Before installing the equipment it is necessary to take the following precautions L f the equipment is mounted in an enclosed or multiple rack assembly the environmental temperature around the equipment must be less than or equal to 50 c 2a f the equipment is mounted in an enclosed or multiple rack assembly adequate air flow must be maintained for proper and safe operation 32 f the equipment is mounted in an enclosed or multiple rack system placement of the equipment must not overload or load unevenly the rack system 4
88. rmally closed 5 The software operation need to be enable and set to get the Alarm traps For detail information about the Software Alarm and software control of SNMP alarm traps please reference the Magnum MNS 6K Software User Manual Chapter 19th The Alarm Contacts are on the front left area next to the DC power source of the Magnum 6K16 Series unit and is green in color as shown in the picture 3 6 6K16 Series Port Module 6KPM Installation Note the modules used in the 6K16 Series vertical mount unit are similar to those used in rack mount 6K units except that the top LEDs are positioned for front viewing for the vertical mount 6K16 Series model The modules have the letter V in the model numbers but otherwise are the same In the Port Module materials below all modules are referred to as 6K PM for convenience in describing port module installation Magnum 6K 16 Series Switches are normally received from the factory with all required 6KPM modules installed There may be situations where 6KPM cards need to be added or replaced In cases where additional 6KPM cards are needed the faceplate for an available front mounted slot must be removed The following procedure describes this operation 3 6 1 Preparation for Installing and Removing 6KPMs STOP Be sure the power cord is unplugged from the chassis before attempting to remove and or replace any PM cards Failure to do so may result in damage to the unit and will v
89. rnal DC Dual Source Power Option C1 0 SPECIFICATIONS FOR MAGNUM 6K16 SERIES FIBER SWITCH Power Supply Internal 48VDC Dual Source model Dual Sre 48V DC Power Connector First Source A A 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 36 70 VDC Power Supply Internal 24VDC Dual Source model Dual Sre 24V DC Power Connector First Source A A 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 20 36 VDC Power Supply Internal 125VDC Dual Source model Dual Sre 125V DC Power Connector First Source A A 2nd Source B B GND Terminal for earth or ground wire connection to the hub chassis Input Two separate sources each at 115 150 VDC With the exception of the dual DC input power connections and the power supply all specifications and configuration options for the Magnum 6K16 Series 48 VDC 24VDC and 125VDC models with this Dual Source option are identical to those listed in the Magnum 6K16 Series Fiber Switches Installation and User Guide including Appendix B Internal DC Power Supply Option 65 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 C2 0 MAGNUM 6K16 SERIES with 48VDC 24VDC and 125VDC Dual Source option The 6K16 Series Switch models with the int
90. rts and four 2km mm LC connectors 6KP8V 45SLC 4 4 module w four RJ 45 ports and four 2km sgl m LC connectors 6KP6V RJMST 4 2 module w four RJ 45 ports and two 2km mm FX ST s 6KP6V RJMSC 4 2 module w four RJ 45 ports and two 2km mm FX SC s 6KP6V RJSSC 4 2 module w four RJ 45 ports and two 20km Sgl m FX SC s 6KP6V RJSSCL 4 2 module w four RJ 45 ports and two 40km Sgl m FX SC s 6KP6V MT10ST 4 2 module w four MTRJ ports and two 10Mb 2km FL ST s 6KP6V RJ10ST 4 2 module w four RJ 45 ports and two 10Mb 2km FL ST s 6KM BLNK Blank cover for one 6K16V A B module slot opening in a 6K16V Gigabit 1000Mb module option for Magnum 6K16V 6KP5V G4RJ G 2 module w one GBIC transceiver amp four 10 100 RJ 45 connectors 6KP3V G2SC G 2 module w one GBIC transceiver and two 100Mb 2km FX SC Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 fiber ports connector GBPMV 20TX Two port Gigabit 6K module for 6K16 Series Switches provides two GBIC open transceiver port for a user selectable GBIC transceiver module GBPMV COTX One slot Gigabit 6K module for 6K16 Series Switches uses one 6K16 Series slot and provides one GBIC open transceiver port for a user selectable GBIC transceiver module DIN RAIL VRM _ Set of two DIN Rail holders for a secure vertical mount of a 6K 16 Series unit with screws to attach to metal mounting brackets and to the 6K 16 Series case M
91. s Fig 3 6 2g Top View 6KPM Module installed inside a 6K16 Series Step 7 Once the installation of granddaughter and i g t 4 R g ii aS vor fo daughter modules is done the front panel screen plates need to be placed on the front of the chassis cover to complete the installation process for that port module The front panel screen plate comes along with the package of port module separately along with 3 brackets and 6 256 flat head screws The brackets and screws have been installed inside of the top cover www GarrettCom com ss ss 39 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Step 8 Once all 6KPM cards have been installed including faceplates for empty slots the chassis cover should be replaced Make sure the chassis cover is aligned properly before securing the enclosure 3 6 3 Removing 6KPM Cards To properly remove a 6KPM card from the 6K16 Series Managed Fiber Switch follow the 3 steps below Step 1 Remove chassis cover See procedures in Section 3 6 1 above Caution Be sure the power cord is unplugged Step 2 Remove retaining screws placed on top for the 6KPM and Face Plate On the top of the daughter module there are six retaining screws for each 6KPM card These screws are used to secure a 6KPM card in position see Figure 3 6 3a Remove the three standoffs holding the Granddaughter board with the chassis The screen faceplate screws out from the inside front of th
92. s Dedicated Equipment Rooms Electrical Closets or the like 2 48VDC products shall be installed with a readily accessible disconnect device in the building installation supply circuit to the product 3 This product shall be provided with a maximum 10A DC Listed fuse or circuit breaker in the supply circuit when connected to a 48V centralized source 4 The external power supply for DC units shall be Listed Direct Plug In power unit marked Class 2 or listed ITE Power Supply marked LPS which has suitably rated output voltage i e 24VDC or 48VDC and suitable rated output current 5 Product does not contain user replaceable fuses Any internal fuses can ONLY be replaced by GarrettCom personnel through the RMA process Installation requirements See pg 27 Sec 3 0 for additional information 1 Elevated Operating Ambient Temperature If installed in a closed or multi unit rack assembly the operation ambient temperature of the rack environment may be greater than room ambient Therefore consideration should be given to installing the equipment in an environment compatible with the manufacturer s maximum rated ambient temperature Tmra 2 Reduced Air Flow Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised 3 Mechanical Loading Mounting of the equipment in the rack should be such that a hazardous condition is not achie
93. s It enables the port s cable to be cascaded X to a 10 100Mb repeater or switching hub in the network The Up link Switch position is configured as straight position by default from the factory settings on all the RJ 45 ports either used for all copper module or combo module 4 4 Auto Cross MDIX and Auto negotiation for RJ 45 ports The RJ 45 ports independently support auto cross MDI or MDIX in auto negotiation mode and will work properly with all the other connected devices with RJ 45 port whether it supports Auto negotiation or not e g 10Mb Hub media converter or fixed mode at 10Mb or 100Mb Half Full Duplex managed switch No cross over cable is required while using the 6KP8 s copper port to other devices Operation is according to the IEEE 802 3u standard The Managed 6K 16 Series Fast Ethernet copper ports can be set for either fixed 100Mb speed or for 10 100 F H N way auto negotiation per the IEEE802 3u standard The selection is made via MNS software The factory default setting is for auto negotiation At 10Mb or 100Mb fixed speed the user may select half or full duplex mode by MNS Software for each RJ 45 port separately For detail information See Section 10 1 at page no 52 of this manual to access the 6K MNS Rel 3 Software user guide www GarrettCom com 43 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 One frequently used application for the Managed Magnum 6K16 Series Switch
94. s by providing copper fiber media along with the higher bandwidth support of 10 100 and 1000Mb The user can utilize the SNMP feature equipped with VLAN RMON STP and other standard managed LAN features to provide a secure and stable network The 6K16 Series Managed Fiber with S ring and Link Loss Learn feature easily fulfilled the redundant requirement in a secured and faster reconfiguration time for cable breakup by setting up in a ring topology The Gigabit port option boosts the bandwidth for high speed to support the peak traffic and minimize congestion Magnum 6K25 IBER Connection lagnum 6K16 Series Fig 2 4b Magnum 6K16V equipped with S Ring in redundant ring solution 25 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Example 3 In another application in a Telco environment 12 port Nebs compliant 48 VDC operated managed switch is required to meet the fiber and copper connection to store the sensitive data The switch must be snmp enabled and managed to easily manage the whole setup Magnum 6K 16 managed carrier class switch easily qualifies for this requirement with all the features and modularity Loaded with management MNS 6K the 6K16 provides a very effective and economical solution for the carrier class space environment Equipped with a rack mount solution to deploy side by side the carrier class managed switches also provide the port density in a rack mounting space The secu
95. the 6K16 Series Switches supporting four Copper and two single mode Long Reach fiber network segments The 6KP6 RJSSC when installed in a Magnum 6K 16 Series Switch has copper supporting the 100m distance and Fiber supporting single mode fiber cable lengths of as much as 40 Km see Power Budget Section 4 5 Each port has an Activity ACT LED indicating packets being received a www GarrettCom com ss 51 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Link LK LED indicating proper connectivity with the remote device when lit and a FDX HDX LED indicating full duplex mode when lit or half duplex when off The 10 100 LED indicates the speed for the copper port which is 100Mbps when the LED is ON and 10 Mb when the LED is OFF 5 2 4a 6KP6 RJ10ST 4 10 100 Mb copper port and 2 10Mbps multi mode FL ST type twist lock connector The Magnum 6KP6 RJ10ST is also a Combo module equipped with 4 dual speed copper ports and 2 multi mode 10 Mb fiber ST type connectors It provides a combination of copper and Fiber functions in one module to the 6K16 Series Switches supporting four Copper and two 10Mb of ST fiber network segments The 6KP6 RJ1OST when installed in a Magnum 6K16 Series Switch has copper supporting the 100m distance and Fiber supporting multi mode fiber cable allow to connect the legacy network of 10Mb requirement in the network Each port has an Activity ACT LED indicating packets bei
96. thod Convection designed for vertical mounting no fans 6K16V Cooling method fan cooling three rear fans 6K16 Weight 4 21 Ibs 1 9 kg Management Console connector DB 9 for RS 232 null modem cable sometimes called an X modem cable Power Supply Internal AC Power Connector IEC type male recessed at rear of chassis Input Voltage 100 to 240 VAC auto ranging Input Frequency 47 to 63 Hz auto ranging Power Consumption 50 watts typical for a fully loaded fiber model 30 watts typical for a fully loaded copper only model DC Power Supply Options 48VDC Power Input Voltage 36 to 70 VDC 24VDC Power Input Voltage 18 to 36 VDC 125VDC Power Input Voltage 88 to 300VDC Std Terminal Block GND Power Consumption same as for AC models see above ww GarrettCom com ss 2 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 For DC internal power supplies at 48 VDC 24VDC and 125VDC including Dual Source options for continuity of operation when either of the DC input sources are interrupted see Appendices B and C Per port MDI or MDIX on RJ 45 The copper daughter board has MDI MDIX Auto crossover on all the RJ 45 ports and eliminate the use of cross over cable between the devices Also port specific user settings such as FDX or HDX copper 10 100 speed can be fixed using software commands Mountings Vertical mounting only Suitable for wall or DIN Rail mounti
97. transceivers covering a long range of distance The GBPM 2O0TX also meets the requirement for those applications where a managed Gigabit media converter is required The two Gigabit slot can be filled with copper Fiber or mix as per the application The 6K16 Series Modules provide a GBIC opening for insertion of industry standard GBICs to provide Gigabit Gb transceivers media flexibility GBIC models are available for both multi mode 550m and single mode 10 25 40 70 km fiber options and Gigabit copper as well with new models appearing often Each port has an Full and Half Duplex F H Activity ACT LED indicating packets being received and a Link LK LED indicating proper connectivity with the remote device when lit 5 2 15 6KM BLNK The 6KM BLNK is a blank face plate or cover plate that must be installed in any empty 6K16 Series PM slot to maintain proper cooling air flow safety etc Two screws underneath the front panel hold the 6 M BLNK in place 6 0 TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments The installation of a Magnum 6K 16 Series Switch is a straightforward procedure see INSTALLATION Section 2 6 the operation is also straightforward and is discussed in Section 4 Should problems develop during installation or operation this section is intended to help locate identify and correct these types of problems Please fo
98. ts Fig 3 6 2d Daughter Board shown upside down with two male latch connectors Step 4 Hold the daughter board with both hands at the end and align the two cream color latching connectors male placed at the bottom of the daughter board with the other female connector placed on the Granddaughter and main board As shown below in Fig 3 6 2e Fig 3 6 2e Magnum 6KPM daughter board aligned with the bottom female connector for the installation 38 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 Step 5 Once the latching connectors are aligned properly and the mounting holes are aligned with stand offs then press slowly and firmly with two fingers as shown below in Fig 3 6 2f on the top of the latching connectors until the connectors latched up securely Figure 3 6 2f Securely latching up 6KPM Cards into a Magnum 6K16 Series NOTE All 6KPM slots need not be filled in order for the Magnum 6K16 Series unit to be operational When leaving 6KPM slots empty always use a face plate Magnum 6KM BLNK to cover the slot opening in the front panel This will maintain proper cooling air flow safety and operation as required by FCC CE and other regulations Step 6 Now screw down the daughter board with 6 440 screws so that it holds the daughter board securely The figure below shows the top view of 6KPM card after successfully installing the 6KPM cards inside the Magnum 6K 16 Serie
99. ture to eliminate the use of cross over cable and the two fiber ports operate at 100Mbps full duplex default User mode control per port through the MNS software is also the same On Magnum 4 2 Combo modules there are four LED s for each RJ 45 port which indicate status the same as described for the 6K P8 RJ45 in Section 2 2 3 above The fiber port s LEDs indicate status the same way as described for the SFF fiber modules in Section 2 2 2 above Color coding on the panel of the module shows which LEDs belong to which port The Magnum Combo six port modules are also available with 4 MTRJ 100Mb mm SFF fiber and 2 10Mb fiber mm ST ports and with 4 RJ45 10 100 copper and 2 10Mb fiber mm ST ports The 4 RJ 45 2 10 Mb ST operation of the SFF fiber and the RJ 45 half of the module is as described for those port types above For detailed information about 10Mb mm ST fiber half of the module see Section 2 2 5 16 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 2 2 6 4 Port 10 Mb and 100Mb mm Fiber ST Modules OQ a Ge pa TX ELK RX TX BLK EX n OQ E TX ELK RX The 4 port 10Mb ST fiber modules behave the same as the 4 100Mb ST fiber modules except for the 10Mb speed For ports numbering ports 1 2 5 6 are present ports 3 4 7 8 are not present There is also a similar 100Mb fiber SC module The default setup on 10Mb fiber module is half duplex which allows the Magnum 6K16
100. update to notes for power substations minor updates as PoE modules option added on Sec 5 2 10 11 minor updates as MDIX support added on all RJ 45 port modules minor updates and tweaks on LC port module 6K16 carrier class managed switch has been added with 6K16V Added Section 3 5 Alarm Contacts and 3 7 1 Console Port pins Updated Section 3 3 DIN Rail and Appendix B DC Power 10 03 Initial Release with Rev A vi Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 THE MAGNUM LINE Industrial networking products Designed and Manufactured in the USA Overview GARRETTCOM INC OFFERS THE PREMIUM QUALITY MAGNUM LINE OF INDUSTRIAL CONECTIVITY PRODUCTS WITH INDUSTRY STANDARD FUNCTIONALITY AND BUILT IN FIBER CONFIGURABILITY MAGNUM PRODUCTS ARE DESIGNED FOR USE IN DEMANDING INDUSTRIAL GRADE CARRIER CLASS POWER UTILITY AND OEM APPLICATIONS WHERE RELIABILITY IS A PRIMARY CONSIDERATION 6K SERIES MANAGED FIELD SWITCHES GIGABIT 100 AND 10 MBPS FIBER AND COPPER PORTS MIX AND MATCH FEATURES SFF FIBER AND DC POWER IN 1U UNITS DX SERIES SERIAL DEVICE ROUTERS ETHERNET AND SERIAL 4K SERIES SWITCHES 100 AND 10 MBPS COPPER PORTS WITH OPTIONAL FIBER PORT WITH AUTO NEGOTIATING FULL SWITCHING PERFORMANCE QUAD SERIES FIBER SWITCHES 100 amp 10MBPS FIBER AND COPPER PORTS MIXED SPEED AND MIXED MEDIA TYPES FULL SWITCHING PERFORMANCE MP62 AND P62F OUTDOOR ETHERNET SWITCHES FOR TE
101. using color bands at regular intervals you must use the color coded strand on the associated ports at each end of the fiber optic segment 3 Connect the Transmit TX port light colored post on the Magnum PM to the Receive RX port of the remote device Begin with the color coded strand of the cable for this first TX to RX connection 4 Connect the Receive RX port dark colored post on the PM to the Transmit TX port of the remote device Use the non color coded fiber strand for this 5 The LINK LED on the front of the PM will illuminate when a proper connection has been established at both ends and when power is ON in the unit If LINK is not lit after cable connection the normal cause is improper cable polarity Swap the fiber cables at the PM connector to remedy this situation 3 2 2 Connecting Fiber Optic SC type Snap In The following procedure applies to installations using a PM with SC type fiber connectors i e using 6K MSC 6K SSC single mode When connecting fiber media to SC connectors simply snap on the two square male connectors into the SC female jacks of the 6KPM until it clicks and secures www GarrettCom com ss 28 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 3 2 3 Connecting Single Mode Fiber Optic When using single mode fiber cable be sure to use single mode fiber port connectors Single mode fiber cable has a smaller diameter than multi mode fiber cable 9 125 micr
102. ved due to uneven mechanical loading 4 Circuit Overloading consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits might have on over current protection and supply wiring Appropriate consideration of equipment nameplate ratings should be used when addressing this concern Reliable Farthing Reliable earthing of rack mounted equipment should be maintained Particular attention should be given to supply connection other than direction connections to the branch circuit i e use of power strip etc iii Magnum 6K16 Series Managed Fiber Switch Installation amp User Guide 03 09 Table of Contents Page 1 0 SPECIFICATIONS sesessesesesecsesosoesesesoecosososseseuocsososoesesecoososossesessecssesse 1 1 1 Technical Specifications sseneseseeseessseseseeseeesersesesesresesseseseseeressrenes 1 1 2 Ordering Informati n sciiicet ikiss ri 4 2 0 Int rod uction scssssscssessscscnsscescsseessssenessscnecessscssscssssssessssenessessenses 8 2 1 Inspecting the Package and Product c cecccsseceseeeteeseeeseeeseeseeeseenes 8 2 2 Product Description Magnum 6K16 Series 6K 16 6K16V 9 2 2 la Magnum 6K16V Managed Fiber Switch eeeeeeeeeeeeeees 10 2 2 1b Magnum 6K16 Managed Carrier Class Switch cece 11 2 2 1 Magnum 6K 16 Series family 6K16 and 6K16V cee 13 22 2 8 port SFF fiber modules 6KP8 M
103. y 10Mb network to the Magnum 6K 16 Series switch They also provide a convenient way for the half duplex hub to connect to the switch through 10Mb fiber ports Whereas the 100Mb ST fiber module allow to connect the 100Mb demand of Switch devices It supports distances according to the 10Base FL standard i e 2Km distance for multi mode fiber Single mode for 10Km distance may be available as a special order Each port has an Activity ACT LED indicating packets being received a Link LK LED indicating proper connectivity with the remote device when lit and FDX HDX LED indicating full duplex mode when lit or half duplex if off 5 2 2 6KP6 RJMSC 4 10 100Mbps RJ 45 and 2 100Mb multi mode FX SC snap in Fiber connector The Magnum 6KP6 RJMSC 6KP6 RJMSC is also a 4 Port 10 100Mbps and 2 100 Mb SC Fiber Port Combo 6 Port module equipped with 4 10 100Mb RJ 45 ports along with 2 multi mode 100Mbps fiber optic transceivers all in one module This is similar to a LINK 10 100 the 6K6 RJMST It has the B 4 ACTIVITY FULL HALF same LEDs indicating port activity ACT Link LK and FDX HDX and 10 100 operation and the same face plate lettering While the functionality of these two modules is essentially the same the 6K P6 RJMSC is equipped with an SC type snap in connector instead of an ST type 50 Magnum 6K16 Series Managed Fiber Switch Installation and User Guide 03 09 5 2 3 6KP6 RJSSC 4 10 100Mbps RJ
104. y and inspected before forwarding can occur This technique ensures that all forwarded frames are of a valid length and have the correct CRC i e are good packets This eliminates the propagation of bad packets enabling all of the available bandwidth to be used for valid information While other switching technologies such as cut through or express impose minimal frame latency they will also permit bad frames to propagate out to the Ethernet segments connected The cut through technique permits collision fragment frames which are a result of late collisions to be forwarded which add to the network traffic Since there is no way to filter frames with a bad CRC the entire frame must be present in order for CRC to be calculated the result of indiscriminate cut through forwarding is greater traffic congestion especially at peak activity Since collisions and bad packets are more likely when traffic is heavy the result of store and forward operation is that more bandwidth is available for good packets when the traffic load is greatest When the Magnum 6K16 Series Switch detects that its free buffer queue space is low the Switch sends industry standard full duplex only PAUSE packets out to the devices sending packets to cause flow control This tells the sending devices to temporarily stop sending traffic which allows a traffic catch up to occur without dropping packets Then normal packet buffering and processing resumes This fl

User Guide - GarrettCom

Contents

Download Pdf Manuals

Related Search

Related Contents