User Manual - Graham Field
Contents
1. 19 19 GF6580BH 1 7 19 GF6590BH 1 HALF NO GAP HEAD dapidus tuta inu aretara arats 20 GF6570B 1 FULL LI a tondere uod ela a cedit 20 LUMEX UNIVERSAL BED RAILS 56 0 eo aaa UE 21 GF6570A 1 FULL LENGTH SIDE RAIL I ideae 21 7 SERVICE PARTS ALL MODELS uade ads da 22 MEME 22 BED END COMPONENTS qasaqa qahaq act et ext 23 BED SERVICE PARTS mM 24 8 MAINTENANCE AND SAFETY CHECKS 25 B LIMITED MAN naa aquqa oe 26 10 INDEX T aasan a 27 GF Health Products Inc is not responsible for typographical errors For the most updated and current information on packaging warranties products and specifications including the most current version of these instructions please visit our website at www grahamfield com Graham Field Lumex and Patriot Homecare Bed Series are registered trademarks and Patriot is a trademark of GF Health Products Inc US0208 INS LAB RevE13 Patriot Homecare Bed 1 The safety statements presented this chapter refer to basic safety information that the operator of the Patriot Homecare Bed shall pay attention to and abi2. 690 5004 025 End panel head foot full electric plastic panels 90 5001066 8002001902 8002001916 399 0955000 0020010 3010000 690 5004 015 End panel head foot full electric walnut panels 690 7604 902 Foot bed end full electric plastic panels o o US0208 INS LAB RevE13 Patriot Homecare Bed 23 BED SERVICE PARTS oe 1 690 201 913 690 2001 412 X Info US0208 and US0208PL are identified on the foot section component label as Patriot Semi Electric Bed Model H7920SE Info USO458 and US0458PL are identified on the foot section component label as Patriot Full Electric Bed Model H7920FE US0208 INS LAB RevE13 Patriot Homecare Bed 24 8 MAINTENANCE AND SAFETY CHECKS Perform the following as needed or between patient placements whichever happens sooner Electronics and Check all controls to ensure that all functions work pum Check all cables for damaged or frayed wires Inspect motor slide caps for excessive wear and deformation Bed frames and Visually check all welds Inspect frames sleeping surface for bending excessive wear The metal parts of the bed are covered with a powder coating Clean all coated parts with mild detergent and warm water Periodically raise head and foot sections of the bed and remove dust from frame Also periodically remove mattress and clean mattress deck Lubrication and Lubricate all caster roller and swivel bearings with light m
3. Bed 16 5 SPECIFICATIONS ALL MODELS High position Se US0208 050208 050458 US0458PL with US0458 US0458PL with 24 0 inches casters in low position casters in standard position 20 0 inches 23 5 inches TAZ xr i r Deck height Low Position 050208 050208 050458 US0458PL with US0458 US0458PL with 15 0 inches casters in low position casters in standard position 9 5 inches 13 inches Bed length Bed Length Info To extend grid length 80 in to 84 in install optional kit 690 0084 000 all beds Low position All models 87 0 inches Deck Width models 36 0 inches Normal operating conditions 450 Ib EVENLY DISTRIBUTED including mattress accessories rails etc Maximum patient weight 350 Ib EVENLY DISTRIBUTED 10 ga 135 high strength low alloy steel roll formed Sleeping surface 11 ga 120 cold rolled steel 5 stage bath 1 S21F acid bath cleans grease and oil from metal 2 Fresh water rinse 3 QuiliPhos 20 phosphate coat inhibits rust and helps maintain electrical charge during powder application All parts are then coated with a colored epoxy powder and baked 35 minutes at 375 degrees F The powder coating finish is approximately 2 5 mils thick The coating is smooth uniform finish without runs wrinkles or grit US0208 INS
4. LAB RevE13 Patriot Homecare Bed 17 6 ACCESSORIES BED RAILS Patriot Homecare Bed decks are equipped with patent pending slots specifically for bed rail installation providing a fixed place to mount GF bed rails Two styles of Lumex bed rails are described in Section 6 1 The Lumex Patriot Liberty bed rail system designed specifically for Patriot Beds and 2 The Lumex Universal bed rail system A WARNING Please read the following bed rail safety information before attaching and using your rails Bed Rail Safety A WARNING If bed rails are not properly installed and adjusted personal injury and or damage to the bed rail could result Please read and understand the following bed rail decal before use BEWARE OF SIDE RAIL ENTRAPMENT Patient Entrapment with side rails may result in serious injury death ALWAYS evaluate patients for and guard against bed rail entrapment in accordance with medical protocols Monitor patient frequently Mattress MUST fit bed frame and side rails snugly to prevent entrapment There may be an increased risk of entrapment when bed rails are used in conjunction with low air loss products Follow the Safety Warnings and Operating Instructions in the Service User s manual Contact your dealer or www grahamfield com For information on Bed safety please see the FDA s brochure concerning Bed Safety and Bed Rails on the website at www fda gov MedicalDevices ProductsandMedicalPro
5. THERMAL MOTOR PROTECTION This product is powered by a quiet efficient DC motor system When the bed is plugged into a power outlet the electrical transformer is always energized in a stand by condition The Okimat actuator casing may feel warm to the touch even when the bed is not being used this is a normal condition Thermal protection activation protection against overheating caused by excessive or extended periods of operation which causes the bed to shut down operation when overheated is a safety feature of this product Causes of thermal protection activation include multiple or repeated adjustment of long duration or the use of multiple functions at one time To ensure trouble free operation always allow a slight pause between multiple adjustments and avoid operating more than one function at a time If thermal protection activation occurs the bed pendant hand control will not function The thermal protection will reset after a period of time dependent on the severity of the overheating To shorten the reset time temporarily unplug the power cord from the power outlet GRAVITY DOWN FEATURE FOR HEAD AND KNEE ELEVATION Patriot beds are equipped with a gravity down safety feature The motors push the head and knee grid decks up but do not pull the knee and head down As the motor plunger retracts the head and knee lower freely minimizing bed damage and or personal injury from items caught under the grid deck Info When using
6. a etae 8 BED ENDASSEMBEY uuu dude M ee M ME 9 ALL BED MODELS ASSEMBLE BED HEAD END ennt tte tnter tette tonne 9 ALL MODELS ASSEMBLE BED FOOT END asss 9 ALL MODELS INSTALL BED END LOCKING 10 FULL ELECTRIC BED ONLY US0458 US0458PL ASSEMBLE HI LO MOTOR SHAFT TO FOOT END GEAR BOX12 HI LO ROD ASSEMBLY BED uci a 13 SEMI ELECTRIC BED ONLY 050208 US0208PL ASSEMBLE HI LO 13 FULL ELECTRIC BED ONLY US0458 US0458PL ASSEMBLE HI LO 13 ALL MODELS ATTACH HI LO ROD GEARBOX OR MOTOR SHAFT PINS tnt 14 BED OPERATION 15 PENDANT HAND CONTROL OPERATION usine is dde 15 SEMI ELECTRIC BED ONLY 050208 50208 1 15 FULL ELECTRIC BED ONLY 050458 50458 2 nino 15 CRANK OPERATION SEMI ELECTRIC BED ONLY US0208 US0208PL ennt 16 TRENDELENBURG POSITION ALL MODELS aasan 16 REVERSE TRENDELENBURG POSITION ALL MODELS 16 5 SBEDIFIGATHONS ALL 17 ACCESSORIES BEDRAILS 18 PATRIOT LIBERTY BED RAIL DESIGN tote rotated ote
7. an expiration date on the component in which case the warranty shall expire on the earlier of warranty period or the expiration date OBTAINING WARRANTY SERVICE GF Customer Service Representative must authorize warranty service Please contact the GF Customer Service department by calling 678 291 3207 sending a fax request to 770 368 2386 or by e mailing a request to cs grahamfield com Specific directions will be provided by the Customer Service Representative Failure to abide by the specific directions will result in denial of the warranty claim EXCLUSIONS The warranty does not cover and GF shall not be liable for the following 1 Defects damage or other conditions caused in whole or in part by misuse abuse negligence alteration accident freight damage tampering or failure to seek and obtain repair or replacement in a timely manner 2 Products which are not installed used or properly cleaned and maintained as required in the official manual for the applicable product 3 Products considered to be of a non durable nature including but not limited to casters filters fuses gaskets lubricants and charts 4 Accessories or parts not provided by GF 5 Charges by anyone for adjustments repairs replacement parts installation or other work performed upon or in connection with such products which are not expressly authorized in writing in advance by GF 6 Any labor or shipping charges incurred in the replacement part
8. consists of an inner and outer tube with a spring button lock to keep them together l Assemble outer and inner tubes Semi electric bed only 050208 USO208PL Assemble hi lo rod Hi lo rod assembly semi electric bed 050208 US0208PL spring button inner tube outer tube inserted S spring button position Depress spring button and insert inner tube into outer tube until third hole is reached as shown above Release spring button to lock it into hole Full electric bed only 950458 USO458PL Assemble hi lo rod Hi lo rod assembly full electric bed spring button 050458 US0458PL inner tube 1 outer tube inserted spring button position Depress spring button and insert inner tube into outer tube until first hole of second hole set is reached as shown above Release spring button to lock it into hole US0208 INS LAB RevE13 Patriot Homecare Bed 13 models Attach hi lo rod to gearbox or motor shaft pins Both ends of the hi lo rod assembly have a slot to mount on the foot end motor shaft pins and bed end gearbox shaft pins Follow steps 2 3 to mount the hi lo rod assembly on the gearboxes notch at end of hi lo rod rests over pin at end of motor shaft FOOT END end of hi lo 1 J lt l rod notch _ masa foot end gearbox end of hi lo motor shaft NN head end gearbox Fig 3 All Bed Models Attach hi lo rod assembly Fig 1 Semi Electric Bed Fig 2 Full Electric B
9. foot symbols shown at right Ensure that bed head and motor head and bed foot and motor foot are matched MOTOR ASSEMBLY pressure slide cap Install motor slide caps Remove motor slide caps P slide cap Remove motor slide caps 1 Remove the slide caps from both ends of the motor as shown above Plungers should be recessed in motor cavities if not plug the power cord into any grounded outlet and operate down function on the pendant hand control then unplug the power cord Info Motor comes from factory with pendant hand control plugged into motor 2 Install 9V backup battery not provided and slide into storage area Install Motors 3 Hold the bed securely positioned with motor cams up as shown above 4 Position the motor over both cams 5 Tap either end of the motor housing shown below with enough force to snap the motor assembly into position on the cam 6 Repeat step 5 for other end of motor US0208 INS LAB RevE13 Patriot Homecare Bed Install motor slide caps 7 Position the caps as shown at right so that the grooves in slide cap are aligned with the grooves in the motor 8 Apply straight downward pressure to each end of the cap while sliding into the closed position 9 Repeat step 8 for the other cap 10 Ensure that all four corners of each slide cap are engaged N WARNING Ensure that the motor is assembled on bed as instructed above before use Motor assembly trouble
10. injury and damage to the bed rails GF6570A 1 Full Length Side Rail Wii hk GF6570A 1 Full Length Side Rail HEADBOARD FOOTBOARD o Buttons Position spring loaded crossbraces into slots G1 and G4 on both sides of bed with spring buttons facing inward as shown above US0208 INS LAB RevE13 Patriot Homecare Bed 21 7 SERVICE PARTS ALL MODELS Service parts for all bed models are shown below and on the following two pages See pictures and tables for appropriate service parts BED COMPONENTS 690 7105 002 Foot section x o 5901106992 L x x 9704500 Endse 5901601900 End set 6007000 L L X L 690 7604 000 L x US0208 INS LAB RevE13 Patriot Homecare Bed 22 BED END COMPONENTS Part number Description Semi electric US0208 US0208PL US0458 US0458PL X 2 690 7001 902 Foot bed end semi electric walnut panels X 690 7601 902 Foot bed end semi electric plastic panels 690 7004 902 Foot bed end full electric walnut panels 3 100 6330 014 Caster non locking each 4 5 100 6330 015 Caster locking each 100 4200 012 554 2001 015 End panel head foot semi electric walnut panels 690 5001 025 End panel head foot semi electric plastic panels 999 0301 904 Caster set of 4 2 locking amp 2 non locking
11. telescoping deck mount bed rails the head and knee may not lower without weight on the bed US0208 INS LAB RevE13 Patriot Homecare Bed 5 3 ASSEMBLY INSTRUCTIONS S HEAD AND FOOT ASSEMBLY gt Foot Assembly head and foot sections Note Grid deck not shown for clarity 1 Place the head and foot sections their sides at approximately right angles to each other with motor cams up as shown above 2 Slide the head and foot sections together until the foot section s hook catches the head section s rivet on both sides Ensure both rivets are completely seated before continuing head wing 28 sections Note Grid deck not shown for clarity linkage plate 3 With the rivets fully seated in the hooks as described in step 2 rotate and straighten bed as shown above Position head wing as shown above A NOTICE While balancing the frame do not elevate the knee too far or the linkage may over extend and lock If the linkage locks manually push the large linkage plate toward the foot of the bed US0208 INS LAB RevE13 Patriot Homecare Bed N WARNING Assemble motor on bed as follows While it is possible to install the motor backwards avoid it Incorrect installation could cause the bed to move in unexpected ways Note that the motor ends are labeled and embossed with head and
12. LUMEX TRIST MODEL 050208 USO208PL SEMI ELECTRIC BED MODEL 050458 US0458PL FULL ELECTRIC LOW EY J ff 2 A ZZ J 4 7 27 USER MANUAL READ THIS MANUAL BEFORE OPERATING THE PATRIOT HOMECARE BED SAVE THIS MANUAL FOR FUTURE USE INFO THE MOST CURRENT VERSION OF THIS MANUAL CAN BE FOUND ONLINE AT www grahamfield com US0208 INS LAB RevE13 CONTENTS 1 SAFETY c 3 WARNING CAUTION NOTICE Mm UN EE 3 2 INTRODUCTION PATRIOT HOMECARE BED USER MANUAL 5 THERMAL MOTOR PROTECTION a edited 5 GRAVITY DOWN FEATURE FOR HEAD AND KNEE ELEVATION aaa 5 3 ASSEMBLY INSTRUCTIONS 6 HEAD AND FOOT ASSENBLY 6 MOTOR ASSEMBLY uu ot eM du qM 7 REMOVE MOTOR SLIDE 2 U U U uuu 7 INSTAEE MOTORS cM EC Mc MM 7 INSTALE MOTOR SLIDE CAPS cca bu dba 8 MOTOR ASSEMBLY TROUBLESHOOTING dude uit tear te ical ue EE TR n IR 8 FULL ELECTRIC BED ONLY 050458 US0458PL CASTER POSITION 8 STANDARD CONVENTIONAL BED HEIGHT trei otra iip 8 LOW BED HEIGHT cada qnd de Ma qasqa qan Q a uite
13. achine oil mechanical Check all bolts and tighten as needed N WARNING bed s electronic system contains serviceable parts Do not open the motors cables or pendant hand control Only a Graham Field authorized distributor or factory trained personnel may perform service or adjustments on these components US0208 INS LAB RevE13 Patriot Homecare Bed 25 9 LIMITED GF Health Products Inc warrants to original purchaser only that it will replace or repair components at GF s sole discretion that are defective in material or workmanship under normal use and service All warranties are conditioned upon the proper use of the products strictly in accordance with good commercial practice and applicable GF instructions and manuals including proper use and maintenance To the extent that a component is warranted by a third party GF conveys all of its rights under that warranty to the original purchaser to the extent permitted This limited warranty shall only apply to defects that are reported to GF s customer service team within the applicable warranty period and which upon examination by GF or its authorized representative prove to be a warranty item This limited warranty is not transferable The warranted components and time period are set forth below The applicable warranty period shall commence from date of shipment to the original customer unless there is
14. as a maximum weight capacity of 450 Ib EVENLY DISTRIBUTED including mattress accessories rails etc This product has a maximum patient weight capacity of 350 Ib EVENLY DISTRIBUTED Ensure that body weight is evenly distributed over the surface of the bed Do not lie sit or lean in such a way that your entire body weight is placed only on the raised head or foot sections of the bed This includes when assisting the user in repositioning or transferring in or out of bed N WARNING In order not to invalidate the warranty or create a hazardous condition resulting in serious personal injury GF Health Products Inc recommends the use of only Lumex replacement parts N WARNING Before operating ensure that the bed frame rivets are properly seated in the bed end hooks otherwise personal injury or damage could result N WARNING Keep all moving parts free of obstructions i e blankets sheets heating blankets pads tubing wiring and other types of products N WARNING Ensure that Bed End Locking Hardware is installed in order to prevent personal injury when moving the bed or using a bed mount trapeze N WARNING WARNING CAUTION labels applied to the bed outline hazards or unsafe practices that could result in personal injury and or property damage do not remove them N WARNING Ensure that the power cord DOES NOT get tangled around the bed bed rails or legs during normal operation of the bed Z WARNING Do not leave the bed unattend
15. be moved or rolled US0208 INS LAB RevE13 Patriot Homecare Bed 8 END ASSEMBLY All bed models Assemble bed head end 1 Insert one locking and one non locking caster into bed end Locking casters must be installed diagonally from each other See previous page for full electric caster position options 2 Standing directly in front of the bed end position it as close to the bed as possible 3 With one hand reach over end and lift up the bed bed head end T Attach bed head end 4 Tilt the bed end slightly back toward you as shown above Engage lower rivet Lower bed onto lock 5 Engage lower rivet slightly with corner lock and tilt end toward bed as shown at above left 6 Lower bed onto corner lock as shown at above right models Assemble bed foot end After bed head end has been attached perform steps 1 6 in All models Assemble bed head end above to install the foot end US0208 INS LAB RevE13 Patriot Homecare Bed models Install end locking hardware 1 After head end has been attached install nylon Bed End Locking Hardware to act as a latch for each corner fender washer Bed End Locking Hardware part number 690 1000 100 includes four lanyards each clove pin ee assembled from a clevis pin hairpin clip fender washer and nylon cord as shown at Lanyard right Bed end locking hardware while not necessary for normal bed operation will prevent the bed end
16. bove opposite slots are directly across bed US0208 INS LAB RevE13 Patriot Homecare Bed 19 GF6590BH 1 No Gap Head Rail head end slot pivot point slot foot end head deck GF6590BH 1 p angle Half No Gap Head Rail mounting slots The Half No Gap Head Rail shown above provides full head coverage of 31 5 inches and extends to eliminate the gap between the head board and the end of the rail The GF6590BH 1 mounted on the bed s head and the GF6580BH 1 mounted on the bed s foot combine to create the Patriot split rail system Half No Gap Head Rail mounting slot locations are shown in mounting slots above opposite slots are directly across bed GF6570B 1 Full Length Rail head end slot GF6570B 1 Full Length Rail The Full Length rail shown above is a nominal telescoping full length rail that provides maximum length rail perimeter coverage Full Length Rail mounting slot locations are shown in mounting slots above opposite side slots are directly across bed US0208 INS LAB RevE13 Patriot Homecare Bed 20 LUMEX UNIVERSAL BED RAILS If you install Lumex universal bed rails follow the installation instructions that accompany them the following instructions are provided to describe the differences between the installation of bed rail crossbraces on Patriot grid beds and spring beds N WARNING Do not use the bed rails as handles for getting into or out of bed this could result in personal
17. cedures GeneralHospitalDevicesandSupplies HospitalBeds A WARNING Patient entrapment with bed side rails may result in serious injury or death Use only with coherent patients capable of avoiding entrapment Patients at risk of entrapment include those who have problems with memory sleeping incontinence pain uncontrolled body movement or who get out of bed and walk unsafely without assistance For at risk patients use only with proper bed side rail protective barriers There is also an increased risk of entrapment when bed rails are used in conjunction with a low air loss product N WARNING Bed side rails are not restraining devices If restraint is required use only proper protective restraints Follow the manufacturer s instructions and applicable regulations Monitor patient frequently A WARNING DO NOT push or pull the bed by the bed rails A WARNING GF Health Products Inc assumes no responsibility for any damage or injury caused by improper installation of bed rails or unauthorized bed rail use Only Lumex bed rails are recommended for use with Patriot beds Please consult the instructions that accompany your Lumex bed rails for complete rail assembly and installation instructions US0208 INS LAB RevE13 Patriot Homecare Bed 18 PATRIOT LIBERTY BED RAIL DESIGN Lumex Patriot Liberty Bed Rails designed specifically for use with Lumex Patriot Beds were developed using the FDA Hospital Bed System Dimensional Guidance to Reduce Ent
18. de by There are additional safety statements in other chapters or sections which may be the same as or similar to the following or specific to the operations Please note the following special statements used throughout this manual and their significance N WARNING Indicates a potential hazard situation or unsafe practice that if not avoided could result in death or serious personal injury N CAUTION Indicates a potential hazard situation or unsafe practice that if not avoided could result in moderate or minor personal injury A NOTICE Indicates a potential hazard or unsafe practice that if not avoided could result in product or property damage Info Provides application recommendations or other useful information to ensure that you get the most from your product WARNING CAUTION NOTICE SUMMARY WARNING To Reduce the Risk of Burns Fire Electric Shock or Personal Injury N WARNING Keep hands and feet clear of all moving parts N WARNING Do not allow small children on or near bed during operation Z WARNING Do not allow this device to be operated by small children N WARNING When operating the hi lo knee or back function of the bed ALWAYS ensure that the individual confined to the bed is positioned properly within the confines of the bed DO NOT let any extremities protrude over the side or between the bed rails when performing any functions N WARNING Under normal operating conditions this product h
19. ed to head end gearbox Attach hi lo rod assembly Attach hi lo rod assembly to foot end gearbox to foot end hi lo motor shaft 2 Connect the hi lo rod assembly to the bed Semi electric bed Attach either end of hi lo rod assembly to the foot end gearbox as shown in Fig 1 above Full electric bed Attach either end of hi lo rod assembly to the foot end hi lo motor shaft as shown in Fig 2 above 3 Attach other end of hi lo rod assembly to head end gearbox as shown in Fig 3 above US0208 INS LAB RevE13 Patriot Homecare Bed 14 4 BED OPERATION N WARNING Ensure that bed is secure and assembled as instructed on previous pages before operating Plug the power cord into any grounded outlet Z WARNING Do not leave the bed unattended when plugged in Info In the event of a power failure use a standard 9V battery to lower the bed s head and foot sections the 9V battery connection is attached to the motor When used with the battery the motor will only lower not lift the head and or foot sections PENDANT HAND CONTROL OPERATION Semi electric bed only US0208 USO208PL The semi electric pendant hand i i to lower head control is shown at right Use the and foot at the pendant hand control to raise and same time lower bed head and foot Each button has a different function as noted in the picture to raise foot to raise head to raise head and foot at the same time to lower foot to lower head Semi
20. ed when plugged in N WARNING Notice for California Customers California Proposition 65 WARNING This product contains a chemical known to the State of California to cause cancer and reproductive or developmental harm US0208 INS LAB RevE13 Patriot Homecare Bed 3 N WARNING Health Products Inc assumes responsibility for any damage or injury caused by improper assembly or use of this product A WARNING GF Health Products Inc specifically disclaims responsibility for any bodily injury or property damage which may occur during any use which does not comply with federal state or local laws or ordinances NOTICE To Reduce the Risk of Product or Property Damage A NOTICE The pendant hand control cord must be routed and secured properly to ensure that the cord does NOT become entangled and eventually severed during use A NOTICE When using nasal or masked type administering equipment oxygen or air tubing MUST be routed and secured properly to ensure that tubing does NOT become entangled and eventually severed during normal operation of bed US0208 INS LAB RevE13 Patriot Homecare Bed 2 INTRODUCTION USER MANUAL This manual contains assembly and maintenance instructions for your Model 050208 US0208PL Semi Electric and US0458 US0458PL Full Electric Low Patriot bed Read the entire manual carefully before using your bed and refer to it during use if you have questions
21. electric pendant hand control to raise head to lower head Full electric bed only US0458 US0458PL The full electric pendant hand control to raise bed is shown at right Use the pendant hand control to raise and lower bed head and foot Each button has a different function as noted in the picture to raise foot to lower foot to lower bed Full electric pendant hand control US0208 INS LAB RevE13 Patriot Homecare Bed 15 CRANK OPERATION SEMI ELECTRIC BED ONLY 950208 USO208PL Use crank at center foot of the semi electric bed shown at right to change bed height raise or lower entire deck Crank operation TRENDELENBURG POSITION ALL MODELS HEAD END AT LOWER ELEVATION THAN FOOT END l Lower bed to its lowest height Disengage the hi lo rod by compressing the spring button and removing the hi lo rod from the motor or bed end 2 Raise the foot bed end using the pendant hand control or crank semi electric bed only The head end will remain in the low position REVERSE TRENDELENBURG POSITION ALL MODELS HEAD END AT HIGHER ELEVATION THAN FOOT END 1 Raise bed to its highest height Disengage the hi lo rod by compressing the spring button and removing the hi lo rod from the motor or bed end 2 Lower the foot bed end using the pendant hand control or crank semi electric bed only The head end will remain in the high position US0208 INS LAB RevE13 Patriot Homecare
22. installation or repair 7 Costs and expenses of regular maintenance and cleaning and 8 Representations and warranties made by any person or entity other than GF ENTIRE WARRANTY EXCLUSIVE REMEDY AND CONSEQUENTIAL DAMAGES DISCLAIMER THIS WARRANTY IS GF S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED GF MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IF ANY MODEL OR SAMPLE WAS SHOWN TO THE CUSTOMER SUCH MODEL OR SAMPLE WAS USED MERELY TO ILLUSTRATE THE GENERAL TYPE AND QUALITY OF THE PRODUCT AND NOT TO REPRESENT THAT THE PRODUCT WOULD NECESSARILY CONFORM TO THE MODEL OR SAMPLE IN ALL RESPECTS THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PARTS GF SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR INCOME LOSS OF USE DOWNTIME COVER OR EMPLOYEE OR INDEPENDENT CONTRACTOR WAGES PAYMENTS AND BENEFITS The warranties contained herein contain all the representations and warranties with respect to the subject matter of this document and supersede all prior negotiations agreements and understandings with respect thereto The recipient of this document hereby acknowledges and represents that it has not relied on any representation assertion guarantee warranty collateral con
23. oot assembly instructions 6 Hi lo rod assembly 13 Info statement significance 3 Introduction 3 L Lumex universal bed rails 21 M Maintenance bed frame and sleeping surface 25 Maintenance cleaning 25 Maintenance electronics 25 Maintenance lubrication and mechanical 25 Maintenance and safety checks 25 Motor assembly 7 Motor assembly troubleshooting 8 Motor slide caps install 8 Motor slide caps remove 7 US0208 INS LAB RevE13 Patriot Homecare Bed N NOTICE statement significance 3 P Patriot Liberty bed rail design 19 Pendant hand control operation full electric 15 Pendant hand control operation semi electric 15 Power failure battery operation 15 s Service parts all models 22 Service parts bed components 22 Service parts bed end components 23 Specification construction 17 Specification weight 17 Specifications dimensions 17 T Thermal motor protection 5 Trendelenburg position 16 Trendelenburg position reverse 16 WARNING statement significance 3 Warranty 26 Weight capacity maximum 3 27 GRAHAM FIELD Manufactured by GF Health Products Inc Fond du Lac WI 54937 Proudly made in the U S A www grahamfield com
24. rapment and tested to the Hospital Bed Safety Workgroup and FDA Dimensional Test Methods for Bed System Zones 1 4 and International Standard IEC60601 2 38 Requirements for the Safety of Electrically Operated Hospital Beds For installation of these FDA compliant bed rails follow the installation instructions that accompany them Patriot Liberty Bed Rail descriptions follow GF6500B 1 Assist Bar The Assist Bar shown at right is a secure handhold and support for active patients who need assistance getting in and out of bed on their own This bar is bolted directly to either side of the bed frame to support the split frame when a patient enters or exits the bed It can also assist patients capable of grasping the bar maneuvering themselves with rotating and GF6500B 1 turning in bed Assist Bar GF6580BH 1 Quarter Rail head end slot foot end pivot point pivot point ARK s foot end pivot point slot foot end slot slotted head deck GF6580BH 1 ic Quarter Rail head end slots foot end slots The Quarter Rail shown above is approximately 18 inches in length when mounted on the Patriot bed It can be used as a head assist head rail or foot rail Mounting slot locations utilized when the Quarter Rail is used as a head rail are shown in head end slots above opposite slots are directly across bed Mounting slot locations utilized when the Quarter Rail is used as a foot rail are shown in foot end slots a
25. s are securely fastened and locked in place US0208 INS LAB RevE13 Patriot Homecare Bed 11 Full electric bed only 050458 USO458PL Assemble hi lo motor shaft to foot end gear box hi l FOOT illo motor END notches in hi lo motor shaft coupler slide over gear box shaft pin gear box hi lo motor shaft Attach hi lo motor shaft to foot end gear box You must first attach the coupler end of the motor shaft to the foot end gear box see above 1 Note the position of the hi lo motor plug on the Okimat actuator next to the pendant hand control plug plug the hi lo motor into the actuator routing the hi lo motor cord under the fixed base frame cross angle as shown below to ensure clearance with the hi lo drive shaft 2 Plug the power cord into any grounded outlet 3 Pull the motor shaft toward the foot end Using the hi lo function on your pendant hand control slowly turn the hi lo motor shaft until the coupler matches up with the gear box shaft pin as shown above 4 Slide the coupler until it rests completely on the pin You may need to manipulate the foot end slightly from side to side and or lift the hi lo motor itself for proper alignment 5 Unplug the power cord N WARNING Ensure power cord is unplugged before performing further bed assembly Route cord under cross angle US0208 INS LAB RevE13 Patriot Homecare Bed 12 HI LO ROD ASSEMBLY BED LENGTH The hi lo rod assembly
26. s from accidentally rolling off when moving or pushing the bed or while installing or using bed mount trapezes Z WARNING GF Health Products Inc recommends the use of Bed End Locking Hardware at all times bracket lanyard hairpin clip bed end removed bracket a b A corner lock Refer to accompanying illustrations while installing Bed End Locking Hardware Remove hairpin clip from the end of the lanyard assembly as shown in a and set it aside Align the cord end with the frame bracket top hole closest to the bed end Insert the cord end through the hole so that an equal amount of cord extends outside either side of the frame bracket hole as shown in b The lanyard assembly will now hang loosely with the clevis pin and fender washer end on the outside as shown in US0208 INS LAB RevE13 Patriot Homecare Bed 10 5 From inside reattach hairpin clip to cord s looped end as shown d This prevents the cord from slipping back through the frame bracket hole 6 From the outside insert lanyard clevis pin with washer into the small hole directly below the bed end bracket top hook so that the washer rests against the bracket as shown in e 7 From the inside insert the hairpin clip now attached to the cord into the clevis pin hole to secure as shown in f 8 Follow previous steps 1 7 for other bed end corners ensuring that all four corner
27. shooting Problems associated with improper motor installation are listed below with appropriate fix Probable cause Head operates with knee control button and Motor is installed backwards Remove motor and reverse it see knee operates with head control button previous page Knee lifting linkages bind against grid Motor is installed backwards enabling Remove motor and reverse it see deck preventing knee deck from elevating knee to elevate too high and bind linkage previous page FULL ELECTRIC BED ONLY 050458 USO458PL CASTER POSITION Any full electric Patriot bed can be used as either a standard height or low height bed by moving the casters fig 1 casters mounted fig 2 casters mounted at low fig 3 casters mounted at low standard height height bed in lowest position height bed in elevated position Standard conventional bed height To achieve standard bed height insert casters into outside legs as shown in fig 1 above Low bed height To achieve low bed height insert casters into inner short legs as shown in figs 2 and 3 above When in the lowest position the casters are engaged for bed movement as shown in fig 2 above When elevated the bed is off the casters and cannot be moved as shown in fig 3 above Due to the clearances involved only minor travel and movement are recommended in the low position The casters can be moved to the outer legs to provide clearance if the bed must
28. tract or other assurance except those set out in this document For additional information on this product or this warranty please contact a GF Customer Service Representative NOTES 1 Additional terms and conditions may apply 2 Freight claims must be notated on the Bill of Lading and must be made with immediacy The ICC regulations govern specific requirements for freight claims Failure to abide by those regulations may result in a denial of the freight claim GF will assist you in filing the freight claim 3 Claims for any short shipment must be made within thirty 30 days of the invoice date GF Health Products Inc 2935 Northeast Parkway Atlanta GA 30360 Tel 770 368 4700 Fax 770 368 2386 www grahamfield com US0208 INS LAB RevE13 Patriot Homecare Bed 26 10 INDEX Assembly instructions 6 B Bed end assembly 9 Bed end locking hardware install 10 Bed extension kit 84 17 Bed height low full electric 8 Bed height standard full electric 8 Bed length adjustment 13 Bed operation 15 Bed rails 18 Bed rail safety 18 C Caster position full electric bed only 8 CAUTION statement significance 3 4 Crank operation semi electric bed only 16 D Deck height high position 17 Deck height low position 17 F Full electric 13 G GF6500B 1 Assist Bar 19 GF6570A 1 Full Length Side Rail 21 GF6570B 1 Full Length Rail 20 GF6580BH 1 Quarter Rail 19 GF6590BH 1 Half No Gap Head Rail 20 H Head and f
Download Pdf Manuals
Related Search