NBL-MB410 User Manual
Contents
1. 250mm VUE ue 11 5kg Power Voltage 100V 240V 50 60HZ Power Corsumptlofi o 5 oerese see eeeeceeee tntan nenna 80W Lamp LED 10W RGBW 4in1 led Color temperature 6500K Illumination Degree 8 Range Dans 540 Tilt 2 2 2 2222 2 nn non nn nen nen nn 2 2 2 2 210 Heat Max temperature 40 C Control and program Data input 3 pin XLR anode Data output 3 pin XLR cathode DMX channels 2 22 16 45 Warranty one year 122. Lifetime 6000 hours Voltage AC 90 220V 50 60HZ Rated power 80 watt Channel 16 45 CH Strobe 1 25hz X Y 540 270 with pan tilt fine Lens 8 degree Dimmer 1 100 liner dimmer IP 20 Mode DMX 512 sound auto Mast slave Function 4 pieces mini led moving head with one 4 beam can be parallel Every mini led moving head can be sole controlled XY dimmer strobe XY speed NW 11 KGS GW 14 KGS Dimension 80 9 25 cm Controller choose function 16channels 16channel 4 head beam bar CH16 mode channel list BU function channel value description CH1 eA Ree 0 fixture sn agang lgpungaha stop macro function 1 255 when O light brightness ratio control 0Y6 100Y6 0 All 51 100 Light 1 CH2 choose light 101 150 Light 2 151 200 Light 3 201 255 Light 4 CH3 X 0 255 CH4 Y 0 255 CH5 XY speed 0 255 XY speed adjustment from fast to slow CH6 R 0 255 CH7 G 0 255 CH8 B 0 255 CH9 W 0 255 CH10 strobe ES 4 255 strobe from slow to fast 0 15 no 16 35 macro1 light flowing jump change XY controllable 36 55 macro2 light flowing gradual change XY controllable 56 75 macro3 light RGB gradual change XY controllable 76 95 macro4 light flowing strobe XY controllable 96 115 macro5 macro 1 macro 4 XY controllable CH11 macro function 116 135 macro 6 XY auto 1 light controllable 136 155 macro 7_XY auto 2 light controllable 156 175 macro 8 XYaut
3. 1 macro 4 XY controllable 116 135 macro 6_XY auto 1 light controllable 136 155 macro 7_XY auto 2 light controllable 156 175 macro 8 XY auto 1 light 176 195 macro 9 XY auto 2 light 196 215 random auto 216 235 macro9 sound 236 255 random sound control CH44 macro function speed 0 255 macro function adjustment from slow to fast 0 249 no effect CH45 reset 250 255 stay five second all motors reset Using construction first Menu second Menu value remark d 001 DMX address 1 512 P 000 Pan 0 255 T 000 Tilt 0 255 R 000 Red 0 255 MANU G 000 Green 0 255 overall B 000 Blue 0 255 W 000 White 0 255 S 000 Strobe 0 255 AL5O 0 99 built in program auto 0 99 speed fast to slow AUTO rd 5O 0 99 random auto 0 99 speed fast to slow AL built in program one sound SOUD beat one step mm random one sound beat one step CH 16 16 45 8 channel mode choice EC On offion _ coding wheel SET rP of offon Dan reverse rt of offlon tilt reverse P1 50 0 99 t1 50 0 99 P2 50 0 99 t2 50 0 99 CAL reset adjustment P3 50 0 99 50 means no fine t3 50 0 99 P4 50 0 99 t4 50 0 99 P1 00 99 99 show the 2 bit LSB of coding t1 00 99 99 wheel reading Measuring RAP Ga AN P2 00 99 99 range is 65535 65535 NEG t2 00 99 99 show value range is 99 monitoring HANS P3 00 99 999 99 99 means 99 if Y t3 00 99 99 decided by Hal
4. fog or smell when turn on power first that is a normal condition which not denote it has quality problem During use the light its housing will be heated and the part of light temperature is high that is a normal condition which should not touch it by hand to prevent injured Please choose the same type bulb amp protective tube when they needed to replace Please turn off the light then removal power cord joints when light fixture is nonuse or required maintenance At least use 2 safety ropes to install light height almost 100cm and ropes must be able to carry tenfold weight of light Child amp non professional do not touch light fixture Professional should watch over light when it using This light could not maintained by user except bulb amp protective tube repairing amp maintaining must follow authorized dealer If customer change light setting privately or operate light by non professional privately both may cause damage to light or injure yourself amp property Any damage caused by improper use will not be assumed by the manufacturer Operating provisions This LED moving head light is available for stage show discotheque and other amusement places It use 200 240 V 50Hz current and only for indoor use Please familiar with its specification before operate the light fixture Check the light appearance amp housing carefully to confirm whether it install stability or screws tight or not This light use Ga
5. USER MANUAL RGBW 4in1 LED Moving Head Beam CE X Please Read Over This Manual Before Operating The Light Fixture 1 Contents L FOP EWO EN 3 2 Security indication eee 3 3 Operating provisions 11er 4 4 Technical specification 5 5 Controller choose function 6 6 LCD Panel indication ENEE REN 6 7 Using construction enne nnne 7 8 Connect multiple fixtures 8 9 Cleaning and Maintenance 8 10 AppendbGsiussueerisix veda XE ENEE EF REV ANA Foreword Thanks for you using The LED moving head light of our Guangzhou Nebula Professional Stage Equipments Co Ltd Please read this product manual carefully before using Anyone undertake the installation operation and maintenance of light fixture should be as follow a Required professional qualification amp experience aiai Comply strictly with the instruction of this manual ROC Reserve this manual all the time when using light until it is no longer in use Pere Completely record in this manual when light fixture has occur any change or maintenance When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the
6. apparatus Security indications Every unit is tested completely before leave the factory and make sure it in good condition to performance In order to keep the light in best situation and safety using please read and comply with the Safe usage instruction amp notice of this manual Very important If who non compliance the safe indication of this manual may cause personal injuries amp property damage This loss no include in the range of quality assurance If the light fixture has suffered fierce expand with heat and contract with cold For example under insolate during transportation do not turn on the current immediately because the water arising therefrom will damage the light Should turn on light until it recover the ambient temperature This light belong to First grade protective product it must use First grade protective safe jack Light fixture must be grounded reliably Do not connect this light with Dimmer Before turn on light please check and make sure the supply power should not higher the power which marks on the bottom panel light power switch should turn to off and 3 check the power cord whether distorted or damaged by sharper Do not let power cord touch other cord directly and be careful when operate power cord amp all joints etc Only can hold its joints when move power cord Hold joints then draw carefully from jack when need to cut power and do not draw cord directly Light fixture may cause some
7. he following 1 the screws bolts of this projector should be locked and not corrupted Should not any deformation at the case Fixing or installation s joining including the ceiling lantern support and so on 3 The accessory of mechanical such as axle rocker must not allow to be wearing and also no unbalanced rotation 4 the power cable should not be damaged cracked and so on if so should change a new one The lens and fan should be cleaned one time each month to make sure its function Gobo flat gobo wheel should be cleaned one time each month by soft brush Soft cloth and typical glass cleaning products should be used for cleaning do not use any organic solvent e g alcohol To keep the rotation smoothly suggest putting some lubricating oil to gobo wheel each three months the quantity of lubricating oil should be less avoid spilling over Color wheel color flat and the inter lens of the projector should be cleaned one time each month There are not user serviceable parts inside the projector except the lamp and fuse Pls uses the same model and standards fuse when replace it Only the authorized distributor can maintain and service the projector If in need of any accessories pls get it from the original factory Please ask advice in case of doubts 11 Appendix Technical specification Weight and size Length 800mm VUE 200mm Height
8. l then shows P4 00 99 99 1 01 or t1 00 01 means detected magnetism OO means not detected t4 00 99 99 magnetism Connect multiple fixtures Note Avoid twisted cables especial the signal wire and power wire either close to each other Otherwise the projector may not work normally Connect multiple fixtures with 3 round pin XLR plug of shielded signal or directly connect to DMX512 controller XLR plug and socket this projector has a 3 round pin XLR socket 3 round pin XLR plug of shielded signal can be used when it connects If the controller has the same 3 round pin XLR socket you can connect the DMX signal output of controller to DMX signal input of projector with distributive signal cables If the controller have other output input sockets for example 5 round XLR socket you must need to buy or make adapter cable As follow Master slave synchronic chain DMX512 Chain connect the first fixture s DMX output cable to the second fixture s DMX input cable with a signal cable connect the second fixture s DMX output cable to the third fixture s DMX input cable eventually and connect the last fixture s output cable if connect the first DMX512 controller to the first projector s DMX input then will form a DMX512 chain if the first projector doesn t connect with any DMX controller then it will can be the master also all the projectors are the master then there will be a master slave synchronic chain N
9. o 1 light 176 195 macro 9_ XY auto 2 light 196 215 random auto 216 235 macro9 sound 236 255 random sound control CH12 macro speed 0 255 macro function adjustment from slow to fast 6 CH13 X fine 0 255 CH14 Y fine 0 255 CH15 dimmer speed 0 255 from slow to fast 0 249 no effect CH16 reset 250 255 stay five second all motors reset 45channels 4 head beam bar CH45 mode channel list channel function channel value description CH9 X2 0 255 CH10 Y2 0 255 CH11 XY2 speed 0 255 XY speed from fast to slow 0 3 no Ss SEH 4 255 strobe from slow to fast CH13 R2 0 255 CH14 G2 0 255 CH15 B2 0 255 CH16 W2 0 255 CH25 X4 0 255 CH26 Y4 0 255 CH27 XY4 speed 0 255 XY speed from fast to slow CH28 strobe 4 sas pa 4 255 strobe from slow to fast CH29 R4 0 255 CH30 G4 0 255 CH31 B4 0 255 CH32 W4 0 255 fixture stop closing lighting and stop macro 0 CH41 total dimmer ee 1 255 when O light brightness ratio control 096 10096 CH42 dimmer speed 0 255 from slow to fast 0 15 no macro1 light flowing jump change XY 16 35 controllable macro2 light flowing gradual change XY 36 55 controllable macro3 light RGB gradual change XY 56 75 controllable 76 95 macro4 light flowing strobe XY controllable CH43 macro function 96 115 macro5 macro
10. ote The last fixture DMX output should connect with a signal plug there is a 12000M resistor between the second and the third pin of 3 round pin XLR socket and it will form a signal plug 1 DMX initial address settings Control panel which on the base of the projector is used for operating this projector including DMX 512 initial address setting and so on this address is the first channel of the DMX512 controller There are 16 channels if the initial address is the first channel then the projector should use the 1st channel to 16 channel and the first channel of the second projector should be 17 channel Avoid repeatedly make sure each projector independently and accurately control With the same initial address of projectors keep in synchronism Initial address settings as follow press ESC until there is A001 or AXXX on the display press ENTER A will be disappear press on or down choose what initial address you want press ENTER to save what your choose if not press ESC 10 Cleaning and Maintenance Note should cut off the power before to clean and maintaining of the projector Do not use the projector if the lens is damaged such as crack or scratch and so on make sure to keep its normal functions Users should keep taking a full testing for the light security amp installation every year by an empirical person and each four years by the specialist When make the testing should consider t
11. s Discharge bulb and do not turn on the current before install suitable bulb Please do not shake the light fiercely when install or operate which should avoid force When move the light should raise its handle beside bottom to avoid strike other part Especially do not raise its head or rocker because improper operate will damage light The light should prevent to be exposing under too heat wet or dust environment during install and do not lay too many cord around light otherwise it may endanger 4 yourself or others Keep the distance at least 1 m between light and receiving surface Whatever install uninstall or repair please insure enclose the light bottom properly At lease use 2 safe cords and safe cord can not use the same lifting hole with light hook Environment temperature can not higher 45 C otherwise bulb will turn off and light also stop work 5 minutes Not allow non professional operate light because most of damage to light due to this non professional operate If light need shipment transport please use original packing include box and polystyrene Forbid to change any light setting with no authorization for security consideration Operate light in other way which different to this manual declaration light may suffer damage and cause its quality invalidation Even this may induce short circuit burning or shut down etc Technical specification Feature Lamp 10w RGBW 4in1 4pcs led high brightness lamp
Download Pdf Manuals
Related Search