RUSH Gobo Projector 1 - User Manual
Contents
1. 12 RUSH Gobo Projector 1 User Manual Key 1 Direction button 4 Lens carrier 2 Speed button 5 Projector body 3 AC power inlet 6 Mounting bracket Projecting a gobo To project a gobo and choose a rotation option 1 Connect the AC power cord to the AC power inlet 2 Loosen the mounting bracket screws Aim the projected image to the desired location Securely tighten the mounting bracket screws 3 Slide the lens carrier in or out of the projector body to the click stop that brings the image closest to correct focus then fine tune focus by turning the lens ring on the front of the lens carrier to obtain the sharpest image 4 Press the Direction button repeatedly to set the desired gobo rotation clockwise counterclockwise or none 5 Press the Speed button repeatedly to set the desired gobo rotation speed fast medium or slow Do not stare directly into the light output Ensure that persons are not looking directly into the LEDs when the product lights up suddenly This can happen when power is applied Note The selected rotation direction and speed settings are stored in memory and applied when the fixture is powered on RUSH Gobo Projector 1 User Manual 13 Replacing a gobo The Rush Gobo Projector 1 accepts size E glass or metal gobos See Gobo on page 17 for gobo requirements To replace a gobo 1 2 32. and particle buildup degrades performance causes overheating and will damage the fixture Damage caused by inadequate cleaning or maintenance is not covered by the product warranty The cleaning of external optical lenses must be carried out periodically to optimize light output Cleaning schedules for lighting fixtures vary greatly depending on the operating environment It is therefore impossible to specify precise cleaning intervals for the fixture Environmental factors that may result in a need for frequent cleaning include e Use of smoke or fog machines e High airflow rates near air conditioning vents for example e Presence of cigarette smoke e Airborne dust If one or more of these factors is present inspect fixtures within their first 100 hours of operation to see whether cleaning is necessary Check again at frequent intervals This procedure will allow you to assess cleaning requirements in your particular situation lf in doubt consult your RUSH by Martin dealer about a suitable maintenance schedule Use gentle pressure only when cleaning and work in a clean well lit area Do not use any product that contains solvents or abrasives as these can cause surface damage RUSH Gobo Projector 1 User Manual 15 To clean the fixture 1 4 16 Disconnect the fixture from power and allow it to cool for at least 15 minutes Vacuum or gently blow away dust and loose particles from the outside of the fixture wi
3. 14 Disconnect the fixture from AC power and allow it to cool for at least 15 minutes Slide the lens carrier out if necessary to access the magnetic goboholder Remove the magnetic gobo holder from the projector body Turn the gobo retaining ring 3 counterclockwise to remove it from the magnetic goboholder 1 Remove the old gobo 2 Magnetic gobo holder gobo and gobo retaining ring Insert the new gobo in the magnetic goboholder with the reversed side of the gobo facing the retaining ring Screw the gobo retaining ring securely back on to the magnetic goboholder Place the magnetic goboholder on the projector body RUSH Gobo Projector 1 User Manual Maintenance Warning Read Safety information on page 5 before servicing the fixture Refer any service operation not described in this user manual to an authorized Martin service technician Disconnect mains power before cleaning or servicing the fixture Service fixtures in an area where there is no risk of injury from failing parts tools or other materials Installation on site service and maintenance can be provided worldwide by the Martin Professional Global Service organization and its approved agents giving owners access to Martin s expertise and product knowledge in a partnership that will ensure the highest level of performance throughout the product s lifetime Please contact Martin for details Cleaning Excessive dust smoke fluid
4. Gobo Projector 1 Ee Gees 2 J i NS CC SC a Sy User Manual RUSA by Martin Professional Entertainment Technology 2013 2015 Martin Professional ApS Information subject to change without notice Martin Professional and all affiliated companies disclaim liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual The Martin logo the RUSH by Martin logo the RUSH by Martin name the Martin name and all other trademarks in this document pertaining to services or products by Martin Professional or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional or its affiliates or subsidiaries Martin Professional e Olof Palmes All 18 s 8200 Aarhus N Denmark www martin com Manual Revision B Table of contents SEENEN mm h 5 fy Wee el Lee IR E 9 Before using the prOdUC S001 S n1 HH TH ng nhu 9 PNYSICal Mstalla ON BEE 10 Fastening the fixture to a flat sur ace ccScS s o 10 AG DOW EE 11 DI e ME 12 FIXTUIFG OVE VI A o 12 Projecting 4 900 0 EE 13 Replacing ANG GODO errada 14 Malntenance ee e a EE 15 Cleaning 717 e Un O a a a a a 15 OPECHICAUOMS van ee N tai 17 Safety information WARNING Read the safety precautions in this manual be
5. able materials well away from the fixture Keep all combustible materials e g fabric wood paper at least 100 mm 4 in away from the fixture Ensure that there is free and unobstructed airflow around the fixture Provide a minimum clearance of 100 mm 4 in Do not attempt to bypass thermostatic switches or fuses Do not stick filters masks or other materials onto any optical component Use only glass or metal gobos Do not insert film plastic paper or any other flammable material in the gobo holder RUSH Gobo Projector 1 User Manual 7 Protection from eye injury Do not stare directly into the light output Ensure that persons are not looking directly into the LEDs when the product lights up suddenly This can happen when power is applied Do not look at the light output with magnifiers telescopes binoculars or similar optical instruments that may concentrate the light output To minimize the risk of eye irritation or injury disconnect the fixture from power at all times when the fixture is not in use and provide well lit conditions to reduce the pupil diameter of anyone working on or near the fixture Protection from injury Fasten the fixture securely to a fixed surface or structure with a minimum of two permanent fasteners Do not fasten with clamps The fixture is not portable when installed Ensure that any supporting structure and or hardware used can hold at least 10 times the weight of all the devices
6. e product warranty The fixture can be hard wired to a building electrical installation or a power plug not supplied with the EU model that is suitable for the local power outlets can be installed on the power cable If you install a power plug on the power cable install a grounding type earthed plug with integral cable grip that is rated minimum 250 V 6 A Follow the plug manufacturer s instructions and connect the wires in the power cable as shown in this table Live or L Neutral or N Earth Ground or US system Black White Green EU system Brown Blue Yellow green The fixture has an auto ranging power supply that accepts AC mains power at 100V 240V 50 60Hz Do not apply AC mains power at any other voltage or frequency to the fixture RUSH Gobo Projector 1 User Manual 11 Operation Read Before using the product on page 9 before operating the fixture Fixture overview
7. ere is no transportation damage before using the fixture Do not attempt to operate a damaged fixture If the fixture is not going to be hard wired to a mains supply install as directed in this manual a local power plug not supplied with EU model on the supplied power cable Before operating ensure that the voltage and frequency of the power supply match the power requirements of the fixture Check the RUSH support pages on the Martin website at www martin com for the most recent user documentation and technical information about the fixture RUSH by Martin user manual revisions are identified by the revision letter at the bottom of the inside cover Note that when the fixture is powered on for the first time it may smoke slightly as it warms up but this will only last a few minutes and is no cause for concern RUSH Gobo Projector 1 User Manual 9 Physical installation Read Safety information on page 5 before installing the fixture The fixture is designed for indoor use only and must be used in a dry location with adequate ventilation The fixture presents risks of severe injury or death due to fire hazards electric shock and falls and is not intended for truss mounting or installation with rigging clamps The fixture must be installed by a qualified technician The safety of the installation is the responsibility of the installer Locate the fixture at least 10 cm 4 in from adjacent surfaces Fasten the f
8. ernal power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixture can easily be disconnected from power Isolate the fixture from power immediately if the power plug or any seal cover cable or other component is damaged defective deformed wet or showing signs of overheating Do not reapply power until repairs have been completed RUSH Gobo Projector 1 User Manual Before using the fixture check that all power distribution equipment and cables are in perfect condition and rated for the electrical requirements of all connected devices The supplied power input cable is rated 6 A If you replace this cable the replacement cable must also be rated 6 A minimum have three conductors 18 AWG or 0 75 mm minimum conductor size have an outer cable diameter of 6 15 mm 0 2 0 6 in and be temperature rated to suit the application In the USA and Canada the cable must be UL listed type SJT or equivalent In the EU the cable must be type HO5VV F or equivalent Protection from burns and fire Do not use the fixture to illuminate surfaces within 200 mm 7 9 in of the fixture Do not operate the fixture if the ambient temperature T exceeds 40 C 104 F The surface of the product casing can reach up to 60 C 140 F during operation Avoid contact by persons and materials Allow the fixture to cool for at least 15 minutes before handling Keep flamm
9. fications see www martin com Disposing of this product RUSH by Martin products are supplied in compliance with Directive 2012 19 EC of the European Parliament and of the Council of the European Union on WEEE Waste Electrical and Electronic Equipment where applicable Help preserve the environment Ensure that this product is recycled at the end of its life Your supplier can give details of local arrangements for the disposal of RUSH by Martin products Photobiological Safety Warning The label shown below is displayed on this product If it becomes difficult or impossible to read it must be replaced using the illustration below to reproduce a new label sized 45 x 18 mm in black on a yellow background RISK GROUP 2 CAUTION Possibly hazardous optical radiation emitted from this product Do not stare at operating lamp May be harmful to the eyes RUSH Gobo Projector 1 User Manual 19 RUSA by Martin Innovation Quality Performance
10. fore installing operating or servicing this product The following symbols are used to identify important safety information on the product and in this manual AAA A A Warning Warning Warning Warning Warning Safety hazard Powerful light See user Hazardous Hot surfaces Risk of severe emission Risk manual for voltage Risk and fire injury or of eye injury important of lethal or hazard death safety severe electric information shock Warning Risk Group 2 product according to EN 62471 Do not stare directly into the beam Do not view the light output with optical instruments or any device that may concentrate the beam This lighting fixture is for professional use only it is not for household use The fixture must be installed by a qualified technician The safety of the installation is the responsibility of the installer The fixture presents risks of Severe injury or death due to fire hazards electric shock and falls It produces a powerful concentrated beam of light that can create a fire hazard or a risk of eye injury if the safety precautions below are not followed If you have any questions about how to install operate or service the fixture safely please contact your Martin distributor see www martin com distributors for details or call the Martin 24 hour service hotline on 45 8740 0000 or in the USA on 1 888 tech 180 RUSH Gobo Projector 1 User Manual 5 Respect all locally a
11. ixture to a secure structure or surface Do not stand it or leave it unfastened where it can be moved or fall over Fastening the fixture to a flat surface The fixture can be fastened to a hard fixed flat surface that is oriented at any angle Ensure that the surface and all fasteners used can support at least 10 times the weight of all fixtures and equipment to be installed on it Fasten the fixture securely with at least two fasteners not supplied inserted through the 7 mm 1 4 in curved mounting slots in the mounting bracket as shown The bracket s 13 mm 1 2 in hole may also be used for fastening Use at least two fasteners for installation 10 RUSH Gobo Projector 1 User Manual AC power Read Safety information on page 5 before connecting the fixture to AC mains power Warning For protection from electric shock the fixture must be grounded earthed The power distribution circuit must be equipped with a fuse or circuit breaker and ground fault earth fault protection Socket outlets or external power switches used to supply the fixture with power must be located near the fixture and easily accessible so that the fixture can easily be disconnected from power Connecting the fixture to a switched AC mains circuit provides a convenient way to power the fixture on and off Do not use an external dimming system to supply power to the fixture as this may cause damage to the fixture that is not covered by th
12. pplicable laws codes and regulations when installing operating or servicing the fixture There are no user serviceable parts inside the fixture Do not open it Refer any service or repair operation not described in this manual to an authorized Martin service technician Do not try to carry out any such operation yourself as doing so may present a health or safety risk It may also cause damage or malfunction and it may void your product warranty Install operate and service RUSH by Martin products only as directed in their user manuals or you may create a safety hazard or cause damage that is not covered by product warranties Follow the safety precautions listed below and observe all warnings in this manual and printed on the product Keep this user manual for future use If you sell the product give this manual to the new owner For the latest user documentation and other information for this and all Martin products please visit the Martin website at http www martin com Protection from electric shock Do not expose the fixture to rain or moisture Disconnect the fixture from AC power before carrying out any installation or maintenance work and when the fixture is not in use Ensure that the fixture is electrically connected to ground earth Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault earth fault protection Socket outlets or ext
13. stallation Mounting Adjustable bracket surface or floor mount Location Indoor use only must be fastened to surface or structure Orientation PP P e Any Connections PAG PONOT A DE IEC Electrical AO DOWD ee 100 240 V 50 60 Hz Power consumption pp 20W Typical power and current 17 6 W 0 285 A 20N S0 H a e e 17 6 W 0 163 A Measurements made at nominal voltage Allow for a deviation of 10 Thermal Oerein EE Convection Maximum ambient temperature Ta Max 40 C 104 F Minimum ambient temperature Ta min 0 C 32 F Total heat dissipation 4 65 BTU hr Calculated 10 Approvals EU safety EN 60598 2 17 EN 60598 1 EN 62471 EN 62493 EULEMO deenens EN 55015 EN c n EN 55103 2 EN 61000 3 2 EN 61000 3 3 EN 61547 BEE E UL 122 Be e FCC Part 15 Class A Canadian Sally osas dal CSA C22 2 No 118 1959 canadian GE ICES 003 Class A EE KEE C Tick N4241 18 RUSH Gobo Projector 1 User Manual Included items Demo Welcome gobo in gobo holder Spare gobo holder Mounting bracket Power cable 1 9 m without mains plug on EU model Ordering Information RUSH Gobo Projector 1 in cardboard box EU model P N 90480060 RUSH Gobo Projector 1 in cardboard box US model P N 90480065 Specifications are subject to change without notice For latest product speci
14. th low pressure compressed air Clean the surfaces by wiping gently with a soft clean lint free cloth moistened with a weak detergent solution Do not rub glass surfaces hard lift particles off with a soft repeated press Dry with a soft clean lint free cloth or low pressure compressed air Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water Check that the fixture is dry before reapplying power RUSH Gobo Projector 1 User Manual Specifications Physical Bet EE 215 mm 8 5 in QI 135 mm 5 4 in ville EEN 152 mm 6 0 in MV SIGNI E 2 kg 11 0 lbs 215 lt gt Fa NX 3 Effects Gobo projection Static rotating replaceable gobo FOCUS EE Manual Optics and Photometric Data HVOF S 0181 CC t PP 20 W LED array ES AN sm 17 Minimum LED lifetime 30 000 hours to gt 70 luminous output Figure obtained under manufacturer s test conditions Control Gobo rotation Direction speed static slow medium fast Control input pp Two onboard control buttons Construction ele EE Silver Protector AIAG EEN IP20 Gobo 2 E24 Size E max image diameter 24 mm Recommended matenal c5 Ss nennen Steel or glass Outside diameter pp 37 5 mm 0 0 2 mm Maximum image diameter pp 24 mm RUSH Gobo Projector 1 User Manual 17 Maximum MICKES S een 3 0 mm In
15. they support Check that all external covers and rigging hardware are securely fastened Do not operate the fixture with missing or damaged covers shields or any optical component If shields lenses or ultraviolet screens have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches send the fixture to an authorized Martin service agent for replacement Block access below the work area and work from a stable platform whenever installing servicing or moving the fixture In the event of an operating problem stop using the fixture immediately and disconnect it from power Do not attempt to use a fixture that is obviously damaged Do not modify the fixture in any way not described in this manual or install other than genuine RUSH by Martin parts RUSH Gobo Projector 1 User Manual Introduction The Rush Gobo Projector 1 isa dynamic effect lamp that projects sharp images from user supplied glass or metal size E gobos It has a 20W LED engine with long life white LEDs The fixture is supplied with this user manual a 1 9 m 6 ft power cable power plug not included with EU model an adjustable mounting bracket floor stand a Welcome gobo mounted in the gobo holder and a spare gobo holder Before using the product 1 2 Read Safety information on page 5 before installing operating or servicing the fixture Unpack and ensure that th
Download Pdf Manuals
Related Search