Home
HSK012HD MAN ENGL 090105 9/1/05 5:42 PM Page i
Contents
1. battery Vehicles that have on board computerized systems may be damaged if vehicle bat tery is jump started Before jump starting this type of vehicle read the vehicle owner s manual to confirm that external starting assistance is advised Excessive engine cranking can damage the vehicle s starter motor If the engine fails to start after the recommended number of attempts discontinue jump start pro cedure and look for other problems that may need to be corrected Check unit periodically for wear and tear Replace worn or defective parts immediately contact Husky Customer Service Department toll free 800 916 7004 Do not attempt to jump start a frozen battery NEVER submerge this unit in water Do not wear vinyl clothing when jump starting a vehicle friction can cause dangerous static electricity sparks Remove all jewelry or metal objects they can cause short circuits or react with battery acid to cause severe burns Remove or secure any loose clothing and restrain long hair before attempting jump start procedure Lead acid batteries generate hydrogen gas during normal operation More gas is generated when the battery is charging Hydrogen gas is explosive poison ous to breathe and highly flammable HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 7 WARNING Always use protective eyewear when using this product contact with battery acid may cause blindness and or severe burns Keep out of c
2. comes with a DC DC charging adapter for recharging the unit from a 12 voltDC accessory outlet in a vehicle or boat AC ADAPTER CHARGER WARNING Do not recharge for more than 4 5 hours maximum using 12 volt DC method HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 8 12 Vout DC CHARGING 1 Insert the plug that is marked TO VEHICLE ACCESSO RY OUTLET of the DC DC charging adapter into the 12 voltDC accessory receptacle on the vehicle or boat 2 Insert the plug at the other end of this charging adapter marked TO JUMP STARTER O UTLET into recharging port on the front panel of the unit 3 Charge the unit until the green FULL indicator lights when Charge Switch Indicator Button is pressed DO NOT EXCEED 4 5 HOURS MAXIMUM 4 W hen charging is completed remove the power cord and store in a safe place DC DC CHARGER ADAPTER 0 lt _ USE THIS PLUG ONLY FOR VEHICLE S ACCESSORY OUTLET OPERATION AS A 12 VOLT PORTABLE POWER SUPPLY 1 Lift up the cover of the units 12 volt DC accessory receptacle See Figure 1 2 Insert the 12 volt DC plug from the appliance into the receptacle on the unit 3 Switch on the appliance and operate as usual CAUTION DO NOT USE THIS UNIT TO OPERATE APPLIANCES THAT DRAW MORE THAN 5 AMPS DC EMERGENCY WORKLIGHT The area light is controlled by an O n O ff switch Make sure the area light is turned O FF when the unit is being recharged or stored REPLACEMENT PARTS For re
3. direct sunlight direct heat and or moisture 10 Check unit periodically for wear and tear Replace worn or defective parts imme diately Contact Husky s Customer Service department toll free 800 916 7004 11 Do not attempt to jump start a frozen battery 12 Never submerge this unit in water FIRST AID SKIN If battery acid comes in contact with skin rinse immediately with running water then wash thoroughly with soap and water If redness pain or irritation occurs seek immediate medical attention EYES If battery acid comes in contact with eyes flush eyes immediately for minimum of 15 minutes seek immediate medical attention IMPORTANT Although this unit is delivered in a partially charged state you must fully charge it with the supplied 120 voltAC charger for a full 48 hours before using it for the first time You cannot overcharge the unit using the AC charger method CAUTIONS Do not expose to rain Replace defective cords or wires immediately SAVE THESE INSTRUCTIONS HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 3 INTRODUCTION Congratulations on selecting the Husky STARTIT Jump Start System This com pact jump starter is unique in the amount of energy supply for its size The inter nal battery is a high density sealed lead acid battery that stores and delivers ener gy comparable to full sized ordinary jump starters Please read this guide carefully before use to ensure opt
4. maximum portability and utility when the Jump Start System is used in remote locations The Jump Start System can be recharged from any standard 120 volt AC power source using the supplied AC Recharge Adapter The adapter barrel connector attaches to the Recharge Port on the top panel of the jump starter A builtin 12 volt appliance socket and the appropriate DC DC charging adapter cord is used to recharge the battery from another 12 volt DC source W hen pressed the CHARGE STATUS button will show the battery power level status from Low to Full The green LED full indicator illuminates when the unit is fully recharged and charging can be discontinued An ON OFF switch operates the builtin work emergency light HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 4 FIGURE 1 Front Panel View FIGURE 1B Rear View 12 Volt DC Accessory Socket for DC appliances with overload protection Battery Level Status Pushbutton LED Charging Battery Level Indicators ON OFF Power Switch Recharging Port Area Light Area Light ON OFF Switch Negative Black Jumper Cable Positive Red Jumper Cable Clamp Holder Tabs ADDITIONAL FEATURES Includes non spillable maintenance free heavy duty new high energy density 17 Amp hour sealed battery Safe to use transport and store Requires no maintenance other than recharging for optimum operation Automatic taper charge for AC recharge Molded high impact case is tough and durable Builtin emergen
5. proximity to the vehicle s battery and engine stand the unit on a flat stable surface and be sure to keep all clamps cords clothing and body parts away from moving vehicle components 9 Do notwear vinyl clothing when jump starting a vehicle friction can cause dan gerous static electricity sparks Remove all jewelry or metal objects that could cause short circuits or react with battery acid 10 Always disconnect the negative Black jumper cable first followed by the pos itive Red jumper cable except for positive ground systems 11 Never allow red and black clamps to touch each other or another common metal conductor this could cause damage to the unit and or create sparking explo sion hazard Always store battery clamps on clamp holder tabs when not in use 12 Do not expose battery to fire or intense heat as it may explode Before disposing of the battery protect exposed terminals with heavy duty electrical tape to prevent shorting shorting can result in injury or fire 13 Do notsmoke or use inflammable items matches cigarette lighters etc while work ing on a vehicle s battery system 14 Keep unit out of reach of children whether stored or in use CAUTIONS 1 Use only the supplied cords adapters for recharging this unit Do notrecharge for more than 4 5 hours maximum using 12 volt DC method Recharge unit after each use 2 All On Off switches should be in the OFF position when the unit is charging or no
6. AINS IM PO RTAN T INFORMATION REGARDING THE AND WARRANTY OF THIS PRO DUCT PLEASE RETAIN FOR FUTURE REFERENCE 4140 SW 30th Ave Ft Lauderdale FL 33312 US Toll Free 866 584 5504 m HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 1 SAFETY INFORMATION WARNINGS 1 W hen working with lead acid batteries always make sure immediate assistance is available in case of accident or emergency 2 Always use protective eyewear when using this product contact with battery acid may cause blindness and or severe burns be aware of first aid procedures in case of accidental contact with battery acid 3 There is a risk of explosive gases being released when lead acid batteries are being charged or discharged Failure to follow instructions may cause property damage explosive hazard and or personal injury 4 When charging unit from a 120 volt AC electrical outlet any wet or damp area make sure that the outlet used is protected by a ground fault interrupt G Fl switch 5 When charging the unit near water do not allow the electrical cords and outlets to get wet or come near water electrical shock could result 6 Jump start procedures should only be performed in a safe dry well ventilated area 7 Always store battery clamps on clamp holder tab on back of unit when notin use Never touch battery clamps together this can cause dangerous sparks power arcing and or explosion 8 When using this unit in
7. HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page i HUSKY 3 YEAR LIMITED WARRANTY PROGRAM This Husky Power Product is warranted by Home Depot to the original purchaser only to be free of defects n materi als and workmanship for three years from the date of purchase without additional charge If you believe that this unit is defective during its original two year warranty period return the unit with proper proof of purchase to the Home Depot store or you may send the product to Husky Power Products at the address below The warranty does not extend to subsequent purchasers or users Husky Power Products will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances Incidental and con sequential damages are specifically excluded from coverage under this warranty This product is not intended for commercial use This warranty does not apply to accessories or damage to units from misuse or incorrect installation connection Misuse includes wiring or connecting to improper polarity power sources RETURN REPAIR POLICY Defective products other than accessories may be returned to Husky Power Products Any defective product other than accessories that is returned to Husky Power Products within 30 days of the date of pur chase will be replaced free of charge If such a product is returned more than 30 days but less than three years after the purchase date Husky Power Products will repair
8. ations stated herein may not apply TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT Contact Husky Power Products Technical Support by tele phone fax or mail We suggest that you keep the original packaging in case you need to ship the unit When return ing a product include your name address phone number dated sales receipt or copy and a description of the rea son for return and product serial number After repairing or replacing the unit we will make every effort to return it to you within four weeks WARRANTY ACTIVATION Please complete Warranty Activation Card and mail to Husky Power Products Enter HSKO12HD as Model and Jump Start System as Product Type Al Husky Power Product products must be regs tered within 30 days of purchase to activate this warranty Mail the completed registration form along with a copy of the original sales receipt to ATTN CUSTOMER SERVICE HUSKY POWER PRODUCTS 4140 SW 30th Ave Ft Lauderdale FL 33312 TOLL FREE 866 584 5504 WARRANTY IS NON TRANSFERABLE AND NON REFUNDABLE lt lt HUSKY The Toughest Name In Tools HSK012HD MAN ENGL 090105 9 1 05 5 42 es Page ii HSKO12HD gt HUSKY The Toughest Name In Tools Jump Start System 12 Volt DC Power Supply lt a IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS TO REDUCE THE RISK OF INJURY USER MUST READ AND UN DERSTAN D THIS INSTRUCTIONALMANUAL THIS MANUAL CONT
9. cy worklight with for roadside repairs and use in remote loca tions without utility power OND gt CAUTION Use only adapters supplied with this unit N ever insert any other adapters into the charging or power receptacles on this unit HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 5 STARTING INSTRUCTIONS 1 Connect Red clamp first then black clamp Disconnect Black clamp first then red clamp Turn OFF vehicle ignition and all accessories radio A C lights cell phone etc Place vehicle in Park and set the emergency brake Make sure jump start system s ON OFF power switch is turned to OFF Remove jumper cables from clamp holder Procedure for jump starting a NEGATIVE GROUNDED SYSTEM NEGATIVE BAT TERY TERMINAL Is CONNECTED TO CHASSIS MOST COMMON Connect positive J red clamp to vehicle battery s positive terminal Ab Connect negative black clamp to chassis or a solid non moving metal vehicle component or body part Never clamp directly to negative battery ter minal or moving part Procedure for jump starting POSITIVE GROUND SYSTEMS NOTE In the rare event that the vehicle to be started has a Positive Grounded System positive bat tery terminal is connected to chassis replace steps 4a and 4b above with steps 5a and 5b then proceed to steps through 8 below 5 Connect negative black clamp to vehicle battery s nega
10. e vehicle s battery and engine stand the unitona flat stable surface and be sure to keep all cords and cables away from any moving parts HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 6 10 11 Always disconnect the engine or frame jumper clamp first followed by the battery jumper clamp Never allow red and black clamps to touch each other or another common metal conductor this could cause damage to the unit and or create sparking explosion hazard There is a risk of explosive gases being released when batteries are charged or discharged failure to follow instructions may cause property damage explosive hazard and or personal injury Always use protective when using this product contact with battery acid may cause blindness and or severe burns Keep out of children s reach ALWAYS store battery clamps in buil in holsters when not in use and never touch battery clamps together this can cause dangerous sparks power arcing and or explosion RECOMMENDATIONS FOR OPTIMUM PERFORMANCE OF THE HUSKY STARF IT ELITE J UMP START SYSTEM CAUTION 1 10 To avoid possible damage that may shorten the unit s working life protect this unit from direct sunlight direct heat and moisture This system is to be used ONLY on vehicles boats garden tractors and gasoline powered generators with 12 volt DC battery systems This system is NOT designed to be installed as a replacement for a vehicle
11. hildren s reach FIRST AID SKIN If battery acid comes in contact with skin rinse immediately with running water then wash thoroughly with soap and water If redness pain or irritation occurs seek immediate medical attention EYES If battery acid comes in contact with eyes flush eyes immediately for minimum of 15 minutes seek immediate medical attention CHARGING RECHARGING For maximum battery life we recommend the Husky STARTIT ELITE JumpStart System be kept fully charged atall times If the battery is allowed to remain ina dis charged state battery life will be shortened NOTE Recharging battery after each use will prolong battery life frequent discharges between recharges will reduce battery life Charge up to 48 hours to reach full charge IMPORTANT MAKE SURE ALL SW ITCHES ARE TURN ED OFF DURING RECHARGING 120 Volt AC Charging Charge unit for full 48 hours using AC method prior to first use Recharge unit fully after each use 1 Simply plug the AC plug of the AC DC adapter charger into any standard 120 volt AC wall outlet 2 Plug the barrel connector attached to the AC adapter charger into the small bar rel receptacle on the jump starter that is marked recharge port 3 When charging is completed and the FULLlightis on remove the AC DC charg er plug and store in a safe place NOTE The unit cannot be overcharged using the AC method The Husky STARTIT ELITE JumpStart System also
12. imum performance and avoid damage to the unit or items that you are using it with The Husky STARTIT EUTE Jump Start System is a compact durable and portable jump start system for vehicles and boats that have a standard 12 volt battery sys tem This self contained rechargeable system will start most vehicles and boats without the need for a host vehicle or 120 voltAC power supply It can also be used as a safe portable source of 12 volt DC electric power in remote locations and or emergency situations Itis ideal for use with Husky 12 volt DC cordless portable rechargeable products Use the Husky STARFIT ELITE J ump Start System to Jump start any engine system with a standard 12 volt DC battery boat truck car air plane RV personal watercraft snowmobile garden tractor gasoline engine generator etc Operate 12 volt DC fans inflators fluorescent worklights cellular phones can quick charge a cellular phone by using the phone s 12 volt DC adapter cord spotlights TVs portable radios cassette or CD players and more The JumpStart System has an easy o ead series of LED Light Emitting Diode charge indicators that show when the unit is fully charged or the level of charge in the bat tery Charge level can be viewed when the charge status push button is pressed A 12 voltDC power accessory socketis provided for use with appliances that can oper ate from a vehicle 12 voltDC accessory outlet This allows
13. place fuse with same type and size fuse 8 amp 4 Replace center pin and spring inside plug 5 Replace gold cap by turning clockwise onto plug SPECIFICATIONS Model sasea meni pa wa Rae Q ata bunga HSK012HD Boost Ampere 400 Instantaneous Cranking Amps Battery Type 12 Volt 17AH Sealed Rechargeable Non Spillable Lead A cid Jumper Cables Heavy Duty W elding Cable Area HORE i s casa aiiin a i a aiaa cha ene Qala qa ed W hite LEDs DC Charging Adapter 12 Volt DC AC Charging Adapter 120 Volt AC 700mA 12 Volt DC O utput 12 Volt O utlet O utput aaa O verload Protection HSK012HD MAN ENGL 090105 9 1 05 5 42 Page 10 lt 2 HUSKY The Toughest Name In Tools
14. placement parts bulbs batteries fuses etc contact Husky Customer Service toll free 800 916 7004 Battery Replacement It is recommended that the unit be returned to Husky Customer Service for battery replacement Contact or toll free 800 916 7004 WARNING Do not dispose of the battery in fire as this may result in an explosion Before disposing of the battery protect exposed terminals with heavy duty electrical tape to prevent shorting shorting can result in injury or fire Do not expose battery to fire or intense heat as it may explode HSK012HD MAN ENGL 090105 9 1 05 5 42 es Page 9 Battery Disposal This unit contains a maintenance free non spillable sealed lead acid battery This battery is fully recyclable and should be accept ed at any location that accepts common automotive starter batter ies Examples of places that accept these batteries are County or municipal recycling drop off centers scrap metal dealers and retail ers who sell automotive replacement lead acid starter batteries For more information on recycling this battery call toll free 877 288 7722 CAUTION THIS PLUG USES AN 8 AMP FUSE FOR CONTINUED PRO TECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE AND RATING TO REPLACE FUSE 1 Remove plug from accessory receptacle Remove the gold cap by turnng coun terclockwise and lifting off 2 Remove center pin and spring Remove fuse 3 Re
15. the unit or at its option replace it free of charge the unit is repaired new or reconditioned replacement parts may be used at Husky Power Products option A unit may be replaced with a new or reconditioned unit of the same or comparable design The repaired or replaced unit wil then be warranted under these terms for the remainder of the warranty period The customer is responsible for the shipping charges on all returned items after 30 days During the warranty period Husky Power Products will be respon sible for the return shipping charges LIMITATIONS This warranty does not cover accessories bubs fuses and batteries defects resulting from normal wear and tear including chips scratches abrasions discoloration or fading due to usage or exposure to sunlight accidents damage during shipping to our service facility alterations unauthorized use or repair neglect misuse abuse failure to follow instructions for care and maintenance fire flood and Acts of God IF your problem not covered by this warranty call our Technical Support Department toll free at 866 584 5504 for general repair information and charges if applicable STATE LAW RIGHTS This warranty gives the purchaser specific legal rights other rights which vary from state fo state may apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the exclusions or limit
16. tin use Make sure all switches are in the OFF position before connection to a power source or load HSK012HD MAN ENGL 090105 9 1 05 5 42 eh Page 2 3 Never insert anything other than the supplied power recharging cords or recommended appliance power recharging cords into the 12 volt DC charging power socket on this unit Do not use any accessory that is not recommended or provided by the manufacturer 4 not use this unit to operate appliances that draw more than 5 amps 5 This system is designed to be used only on vehicles with 12 volt DC battery sys tems Do not connect to a 6 volt or 24 volt battery system 6 This system is not designed to be used as a replacement for a vehicular battery Do not attempt to operate a vehicle that does not have a battery installed 7 Vehicles that have onboard computerized systems may be damaged if vehicle battery is jump started Before jump starting read the vehicle s owners manual to confirm that external starting assistance is advised 8 Excessive engine cranking can damage a vehicle s starter motor If the engine fails to start after the recommended number of attempts discontinue jump start procedures and look for other problems that may need to be corrected 9 Although this unit contains a non spillable battery itis recommended that unit be kept upright during storage use and recharging To avoid possible damage that may shorten the unit s working life protect it from
17. tive terminal 5b Connect positive red clamp to vehicle chassis a solid non moving metal vehicle component or body part DO NOT CLAMP DIRECTLY TO POS ITIVE BATTERY TERMINAL OR MOVING PART Double check the polarity is correct then turn jump start power switch to ON posi tion Start vehicle do not turn key for longer than 5 6 seconds After vehicle starts turn jump start s power switch to OFF position Remove clamps disconnect the negative black jumper cable first followed by the positive red jumper cable and replace them in the clamp holders CAUTION If engine fails to start leave ignition key turned off and disconnect the negative clamp first then the positive clamp Try again later the engine may be flooded Recharge jump start system after each use WARNINGS 1 Before using this system to jump start any vehicle or boat read and understand all instructions safety tips warnings cautions and first aid information provid ed in this manual and on the product labeling Additional important informa tion may also be provided by the vehicle s battery system manufacturer Be aware of first aid procedures before attempting jump start procedure Always wear protective eyewear when working with a lead acid type battery Do not smoke or use inflammable items matches cigarette lighters etc while working on a vehicle s battery system W hen using this jump starter in proximity to th
Download Pdf Manuals
Related Search
Related Contents
User Guide - Manuals, Specs & Warranty ICC IC107FRWAL MAIN BOARD User`s Guide VED® User Manual Arquivo 1 términos de referencia invitación publica 010-2015 Fujitsu LIFEBOOK E743 RX-V1300 - HiFi im Hinterhof Knape & Vogt SDS-FR-28-FNW Instructions / Assembly Copyright © All rights reserved.
Failed to retrieve file