2100 SERIES/GEMINI USER`S MANUAL VER. 2.0 Module
Contents
1. 134 101 102 103 Signal Modules PARTS TOOLS REQUIRED 5 64 Allen Hex Wrench Extraction Tool Signal P N 910 110 110 INSTRUCTIONS Contact Insertion INSERTION 1 To insert Contact into Module first terminate contact i by crimping soldering wire wrapping see termination instructions in Section 7 U 2 Insert terminal into module until front of contact is flush with l module I 3 When installing Wiring Contacts in the Receiver Wiring Module P N 510 133 109 510 133 110 510 133 111 insert the contacts in from the screened side of the module 4 When installing Wiring Contacts in the ITA Wiring Module P N 510 134 101 510 134 102 510 134 103 insert the contacts from the screened side of the module as well Contact Removal 1 To remove the Wiring Contacts place the appropriate Extraction Tool Signal P N 910 110 110 over the contact into the counter bore on the mating side of the module 2 Press into the contact until the retaining ring is released and contact begins to emerge from the rear of the module 3 Remove the contact by hand NOTE In order to maintain contact float wires should be restrained a minimum of 2 inches from the back face of the Module by using a strain relief plate recommended for both Receiver and ITA Modules 910110110 910112112 CAUTION e Twist Power Coaxial and Signal Extraction Tools slightly to ensure that retaining clip ears have fully collapsed before applying pres2. 2100 SERIES GEMINI USER S MANUAL VER 2 0 Module Installation n Removal Instructions ion 1 Twin Access Contact TAC Receiver Twin Access Contacts TAC Module Contact Removal Insructions P N 510 133 101 102 103 104 105 106 Receiver Signal TAC P N 510 133 103 104 107 108 Receiver Coaxial TAC 50 OHM P N 510 133 105 106 Receiver Coaxial TAC 75 OHM P N 510 133 103 104 107 108 Receiver Power TAC PARTS TOOLS REQUIRED CAUTION 5 64 Allen Hex Wrench DONOTd meii ea Phillips Head Screwdriver O NOT depress contacte with fingers INSTRUCTIONS 510133103 Receiver 1 To insert Contact into Module remove the contact retaining plate from the bottom of the module by unfastening the 2 Flat Head Phillips Screws 2 Insert contacts into the rear of the module with the stop ring of the contact facing the back of STOP RING OF the module The contacts will automatically PIN ALWAYS TOWARD drop into alignment RETAINING PEATE 3 Replace the contact retaining plate and secure with two 2 Flat Head Phillips Screws pee soisi piaizidl NOTE The contact retaining plate must be removed prior to the extraction of the contacts To remove the contact retaining plate unfasten L PETAMING BEATE f the 2 Flat Head Phillips Screws and remove the contact retaining plate The contacts are then easily extracted by hand TAC Receiver Module Installation Removal 1 To install a module into the Receiver place the supplie
3. d hardware 4 socket head cap screws in the TAC Re ceiver Module 2 Place the Module in the front of the Receiver aligning the locating pins on the module with the appropriate holes in the Receiver Frame so that the upper and lower module screws touch the mating holes on the Receiver Frame install modules such that the numbers can be read from top to bottom making them right side up 3 Using a 5 64 Allen Hex Wrench tighten the top screw 1 to 2 full revolutions while lightly applying pressure against the face of the module Maintain this pressure while tightening the bottom screw 1 to 2 full revolutions Repeat this sequence in order until the module is seated As the module is being seated watch to ensure that it does not become cocked at any time as a result of the guide pins not being properly aligned with the receiver or binding of the pins due to one screw being advanced ahead of the other more than 1 to 2 turns If this should occur back the screws off until the module is level and repeat the tightening process Torque the screw until it is 4 to 5 inch pounds 7 To remove unfasten using a 5 64 Allen Hex Wrench on the top and bottom screws our 10 VM2100_V2 0 indd www vpc com Virginia Panel Corporation VER 2 0 2100 SERIES GEMINI USER S MANUAL Modul n Installation Removal ion 1 Twin Access Contact TAC Signal Module Contact Insertion Removal Instructions P N 510 133 109 110 111 Signal Modules P N 510
4. sure to handle e To avoid damage to contacts always ensure that tool is perpendicular to Module face Virginia Panel Corporation www vpc com VM2100_V2 0 indd 11
Download Pdf Manuals
Related Search