TS1000 Series Vertical Tripod Turnstile User Manual
Contents
1. Electromagnet g Timer a ABDr HH gt Passing Indicator eu L2R L2COM ga Direction Indicator Direction Indicator COW er e A FUMA Optocoupler Board SanGunLun V1 4 130905 a e Emergency Switch GND Emergency Switch S J HE db GND a Su CP 24VIN E LLO O O LLO O OIL OOOO OTL O LLO OTL LLO O LLO O O Ink 485 Reader x E 5 J pe y pueboiy A S HL 102. fire or other emergencies Direction Indicator Output to connect a LED screen and indicate whether this passage is allowed to pass Passing Indicator Output to connect a LED screen and indicate if user verification is successful and whether it is able to pass Counter Output to connect a LED screen and display the number of people passed that is generated by the push of tripod arms each completed push means pass one time Drop Arm Electromagnet Output to control the tripod arms manually rise up and automatically drop down 4 2 Connection Diagram of the Access Control Panel or Standalone Access Control Device Turnstile Control Board O O or MD s O E a Notes 2 1 The Counter is an optional accessory 2 The lock driving duration of the access control panel or standalone O access control device needs to be set to 1s or Os and the door sensor D H H 5 needs to be set to None Q A Q 3 3 O U O A Figure 4 2 4 3 Parameter Configuration Function description of the DIP switch Figure 5 5 function Setting Opening Duration 4 3 1 Setting the Turnstile Opening Duration Opening duration refers to the period of time from opening to closing once the turnstile receives an open signal In the DIP switch number 1 2 and 3 are used for duration setting It can be set to different values from 5s to 60s according to the following chart Duration Bit
3. than 80 mm see figure 3 1 Setting a warning line for card swiping see figure 3 2 A warning line is suggested to prompt users to swipe cards in a distance which would greatly reduce the probability of equipment failure caused by improper operations Figure 3 2 3 2 Cabling There are inlets in the bottom plate for cabling as shown in figure 3 3 Power supply and communication wire should go through the inlet Cable protection covers are suggested to use if it is surface mounted Warning The tripod turnstile must be connected to Ground earth there is wiring interface in the power switch A y 00 OO amp WIWQO CS 320 00mm Es Figure 3 3 3 3 Installation 1 Drilling holes Drill holes based on the locations of the holes shown in figure 3 3 2 Fix the mounting plate to its original position Placing the mounting plate properly and apply screw securing glue on the surface and the threads of the expansion bolts install four 3 expansion bolts to secure the mounting plate and use a horizontal ruler to test the levelness of the mounting plate If the mounting plate is not level adjust it by the gaskets provided Note that all the four expansion bolts must be installed properly as shown in figure 3 4 o soo Nan A NA_ GRAN 4 Screw securing glue shall A aa iw be applied on the threads i i Sd 3 Figure 3 4 3 Put the turnstile on the mounting plate and tighten
4. the screws Apply screw securing glue before use and put gaskets on the screws to adjust the direction of the turnstile If the tripod turnstile is not level you can place gaskets to adjust as shown in figure 3 5 Installation levelness A Installation levelness Figure 3 5 4 Cable Diagram 4 1 Function Description of the Turnstile Control Board If you are using TS1011 or TS1022 all the connections between access control and turnstile control board are done in factory Just plug in communication cable to access controller and do the setting If you are using TS1000 you need to connect access control system to the turnstile control board please check the content in this chapter carefully Warning The third party access control system lock relay trigger time should be 1 second or less than 1 second Ne of So ait es i gael see Nine a ins E ait in a y a Q T SO PO 59 5U 50 QO 85 g5 3 O 353 CJ 2 E 8 gt SQ 2333 BF DR ef 30 39 T co 36 658 ZR cu 55 ns un 5 O A so E H aS E Pe ze Wn D O O o O oO 0 oo O G JI Q 2 Cc Oc 5 5 0 OD OD O D v Q cCOo h ES 5 2550 02 a O lt D So 5 5 o a 059 Do lt D gt UN co o o a a O 3 gt On ae D Nn a A 9 2s Do 2 5 E a wm 3 Q5 5 O E 5 Q 5 o gos 52 ES E v s OOo ct Figure 4 1 Interface description Opening Signal Input to receive relay signal and open the turnstile Emergency Switch to keep the turnstile open in case there are
5. In case of emergencies This equipment is designed to drop down arms automatically if there is power failure thus make the passage being open to the public And there is interface in the turnstile board to connect an emergency switch which would make the tripod turnstile keep open in case of emergencies Note after power restoration wait for more than 6s and then lift the arms manually 5 2 Maintenance Forming maintenance consciousness The tripod turnstile needs to be maintained regularly and repaired once it is damaged It is recommended that warning signs being placed at conspicuous positions for prompting passers by to pass in a proper way and in good order Reasonable maintenance consciousness helps to guarantee long term usage of the tripod turnstile Regular maintenance Cleaning and protection liquid dedicated for stainless steel are recommended to wipe the outer shell of the equipment regularly The tripod turnstile used outdoors or in an environment with lots of dust must be maintained once a year at least Note regular maintenance should be performed after power off the equipment The damping accumulator is used to adjust the tripod turnstile s elasticity and return speed You can rotate it in clockwise direction to enhance and in anticlockwise direction to weaken the elasticity and return speed of the tripod turnstile See figure 5 2 Figure 5 3 shows the mechanical and electrical structure of this equipment Drop arm Optical coupli
6. PTU Toco TS1000 Series Vertical Tripod Turnstile User Manual Security and Time Management Solutions Version 1 0 Time 2014 3 TS1000 Tripod Turnstile TS1011 Tripod Turnstile with Controller and RFID Reader TS1022 Tripod Turnstile with Controller and Fingerprint Reader with RFID function Please read this document carefully before installation and using the device 1 Technical Specifications 280 500 tn 086 120 Figure 1 2 Unpacking and Testing the Tripod 2 1 Unpacking The vertical type tripod turnstile is top heavy and unsteady do not remove the foam at the bottom before installation as shown in figure 2 1 Do not remove the foam lining at the bottom before installation Figure 2 1 2 2 Arm Installation Method Installation procedure 1 Open the glue and apply in the square openings of the arms as well as the four countersunk screws as shown in figure 2 2 This is to prevent screws from getting loose due to vibration after being used for a long time 2 Insert the arms to the connection points and use the Hex key to fasten the four countersunk screws on each arm as shown in figure 2 5 nn i s _ nn A e e Tighten the four screws on each B lt A EE arm in clockwise direction Y HF a gt a E 3 ay je This Opening shall be S applied with glue evenly IN Figure 2 2 Figure 2 3 2 3 Power on Test Before
7. Setting Duration Bit Setting 10s 100 40s 15s 010 50s 20s 110 60s Note The turnstile opening duration is set to 5s by default 4 3 2 Direction Indicator It is to indicate whether the passage allows people to pass The green arrow means passing is allowed while the red X means passing is prohibited The indicator status can be set through number 4 and 5 in the DIP switch The description of the bit settings are as follows 00 One way traffic Green indicator indicates that passing is allowed while red indicator indicates that passing is prohibited 10 One way traffic Green indicator indicates that passing is allowed while red indicator indicates that passing is prohibited 01 Passing is allowed in both directions 4 3 3 Memory Function With the memory function the turnstile could remember at most 20 swipes of one card at one time and allows up to 20 visitors to pass so they don t have to swipe card each time this function can be enabled or disabled through number 6 in the DIP switch The description of the bit settings are as follows ON up indicates that the memory function is enabled OFF down indicates that the memory function is disabled 5 Equipment Precautions and Maintet 5 1 Precaution 1 It is recommended to purchase optional accessories to use in outdoor environment 1 It shall install optional cooling fans for the equipment if the working temperature is often above 50 C 2 It is equivalent
8. ng Damping blanking disc accumulator electromagnet NOE Figure 5 2 6 Troubleshooting The indicator is not lighted when the equipment is powered on The arms of the tripod turnstile cannot be lifted manually after the equipment is powered on The tripod turnstile does not open after authentication The passing is not smooth after the turnstile is opened it encounters resistance when pushing the arms and the arms cannot return to the home position after they rotate The arms drop during the use Turnstile opening Trilobed wheel Lock rod electromagnet Turnstile opening electromagnet Lock rod E 6 Sy NS Figure 5 3 hime It may be caused by the power supply or circuit Check whether the connection cable and power cable between are damaged or the wiring is loose It may be caused by the problem of relative components or drop arm electromagnet Check whether the stop base and turn plate withstands each other as shown in figure 6 1 Check whether the drop arm electromagnet is operating Remove the upper cover of the framework use a hex key to remove the cover of the control module as shown in figure 6 2 and check the work s
9. tatus of the electromagnet as shown in figure 6 3 It may be caused by lack of permission or a circuit problem Check whether the user has the permission to open the turnstile Use a multimeter to check whether the NO and COM ports of the access control system has a relay signal output 3 Short circuit the ports K1 GND and K2 GND if the turnstile is successfully opened it would be the controller problem In this case please refer to Attachment 2 to check the cable connection of the controller It is caused by the damper Adjust the damper as shown in figure 5 2 It may be caused by the problem of relative components or drop arm electromagnet Check whether there is any gap at the position shown in figure 6 1 Check whether the drop arm electromagnet is totally closed If not power off the equipment and power on it again 2 minutes later Control module cover Screw for securing the control module cover Figure 6 1 Figure 6 2 NN N Normal status of the drop arm Normal status closed of the drop arm electromagnet after being powered off electromagnet after being powered on Figure 6 3 Attachment 1 Default Factory Settings 6 Passing Direction Indicator Passing is allowed Green Arrow Note The Lock Driving Duration is default 5 seconds please set to 1 second Attachment 2 Connection Diagram Overvi ES Opening Electromagnet P Opening Electromagnet cS Drop arm
10. the Installation of Device 1 Please make sure that the power requirements are strictly met to avoid permanent damage to the unit You could change the input voltage 110V or 220V through the DIP switch as shown in figure 2 4 Note The tripod turnstile must be connected to ground earth 2 Power on and wait 30s for the tripod turnstile to finish the self check program 3 Lift the arms manually as shown in figure 2 5 4 Check whether the tripod turnstile and the LED indicators work properly If there is any problem please refer to section 4 2 or kindly contact the supplier There is a voltage AS J E DIP switch in the Z side direction of a 220 E this power supply i A O ma 110V S HE 3 D gt Figure 2 4 Figure 2 5 g g 3 Equipment Installation 3 1 Installation Conditions The equipment must be installed on concrete ground ensuring that expansion bolts can be secured firmly You are suggested to install an assistant framework or fence to form a passageway as shown in figure 3 1 Spuemdn 47 100 lt 80 J M WLI JUB SISSY a A E A a NS a e 4 4 4 Figure 3 1 Note L When installing the tripod turnstile against the wall please reserve at least 100 mm space in order to open the cover for adjustment and maintenance The space at the end of the arm shall not be greater
11. to IP54 waterproof under proper installation However it cannot work in the region that may suffer typhoon 3 If the temperature is 30 C a heating plate is suggested to install It might need multiple times to power on while getting hot automatically through the self check program 4 The service life of this equipment may be shortened if it works outdoors in coastal areas or a region prone to acid rain 2 If the power and signal cables are connected properly this equipment can be immersed in water of 250 mm deep but it must not be powered on for operating when it is immersed in water 3 Itis highly recommended that a card swiping warning line to set for prompting passers by to swipe cards properly and a reasonable passage width shall be set to prevent passers by from squeezing in illegally 4 It is recommended that a warning sign is placed at a conspicuous position and prompt Please swipe your card outside the warning line and pass in order Thank you The maximum tolerance of the tripod turnstile s arms Please note that the maximum stress tolerance at the center of the arm is 80kg and at the ends of the arm is 40kg See figure 5 1 When the impact force on the tripod turnstile reaches the designed limit the arms break down first to ensure that the whole equipment is not damaged and the passer by is not injured e y sz 8 l o 2 Osx X mo 23 2g a an D3 D3 COW KW o on A 5 o E o G ME Figure 5 1
Download Pdf Manuals
Related Search