NeTYS PR 3000 VA - Effekta Power Systems AB
Contents
1. OFF position during the connection procedure UPS EXT1 2 nv d Ver 2 iD HER Sl 2009000 paaaaa paaaaad Place the battery expansion unit beside the UPS on the side with no air vents Connect the battery expansion unit to the UPS using the special cable supplied Once connection has been completed configure the back up expansion unit using the special menu as described in chapter 4 SWITCHING THE UPS ON Switch the UPS on by pressing the ON button on the front panel The Normal mode LED will light up allow ten seconds for the self teach procedures to run When you are sure that the UPS is functioning properly the various loads may be switched on and work may commence in protected mode SWITCHING THE UPS OFF Warning This UPS has been designed to control and maintain the battery charge therefore only in exceptional circumstances are you advised to switch it off completely To shutdown the UPS completely press and hold down the OFF button and take out or disconnect the mains power supply The UPS switches off all the LEDs and is then fully deactivated If the mains cable is not disconnected the battery charger remains active 8 amp SECTION 1 EG 2DKOOROO doc FR Ja SICON UPS NeTYS 1000 3000 VA Product Manual CONFIGURATION AND START UP 4 CONFIGURATION AND START UP CONFIGURA2. RS232 USB NET VISION TCP IP amp SNMP optional card UPS Management software Windows amp Linux free download Optional UNI VISION PRO CD Windows AIX4 3 5 1 HP UX10 20 11 Solaris 8 9 GNU Linux Novell 5 6 NTP data line suppressor RJ45 10 Base T lt 45 dBA at 1 meter 0 40 C 10 25 C for optimum battery life Altitude 2000 mt humidity 95 non condensing EN IEC62040 1 1 safety EN50091 2 IEC 62040 2 EMC EN 61000 4 5 C62 41 1991 surge 87 x 385 x 235 2 87x 415 x 220 87 x 585 x 440 435 x 415 x 87 440 x 585 x 87 9 6 Kg 18 Kg 19 Kg 31 5 Kg SECTION 1 6 13 Socomec Sicon UPS worldwide INEUROPE BELGIUM Schaatsstraat 30 rue de Patinage B 1190 Bruxelles Tel 32 0 2 340 02 34 Fax 32 0 2 346 16 69 ups sales socomec com FRANCE 95 rue Pierre Grange 94132 Fontenay sous Bois Cedex Tel 33 0 1 45 14 63 90 Fax 33 0 1 48 77 31 12 ups paris dcm socomec com GERMANY Heppenheimerstrake 57 D 68309 Mannheim Tel 49 0 621 7168 40 Fax 49 0 621 7168 444 info sicon socomec de ITALY Viale Tolstoi 73 Zivido 20098 San Giuliano Milanese MI Tel 39 02 98 242 942 Fax 39 02 98 240 723 siconmi socomec com NETHERLANDS Bergveste 2F NL 3992De Houten Tel 31 0 30 63 71 504 Fax 31 0 30 63 72 166 info socomec nl SLOVENIA Savlje 89 SI 1000 Ljubljana Tel 386 1 5807 860 Fax 386 1 5611 173 info socomec sicon ups si SPAIN C Nord 22 Pol
3. Ind Buvisa 08329 Teia Barcelona Tel 34 93540 7575 Fax 34 93540 7576 info socomec aron com UNITED KINGDOM Units 401 402 Cirencester Business Park Love Lane Cirencester Gloucestershire GL7 1YG Tel 44 1285 644 444 Fax 44 1285 644 414 ups uk sales socomec com VALID FOR BR VALID FOR ITALY n 5 ME OCE VERSION 2000 IN ASIA INDIA Atma Ram Mansion 1 21 Asaf Ali Road IN New Dehli 110 002 Tel 91 11 23234411 Fax 91 1123232639 hpl hplindia com SINGAPORE 25 Tagore Lane 01 02 Singapore Godown SG 787 602 Singapore Tel 65 6 554 0900 Fax 65 6 458 7377 general socomecsicon com sg THAILAND 17 178 Prachachuen Road Tungsonghong Laksi TH 10210 Bangkok Tel 66 2 503 92 43 Fax 66 2 503 99 23 inquiry socomec unitrio co th HEAD OFFICE SOCOMEC GROUP SWITCHING PROTECTION AND UPS S A capital 10 923 800 R C Strasbourg 548500 149 B SOCOMEC SICON UPS Strasbourg 11 route de Strasbourg B P 50 F 67230 Huttenheim FRANCE Tel 33 0 3 88 57 45 45 Fax 33 0 3 88 74 07 90 ups benfeld admin socomec com SOCOMEC SICON UPS Vicenza Via della Tecnica 1 36030 Villaverla ITALIA Tel 39 0445 359 111 Fax 39 0445 359 222 info it ups socomec com SALESAND MARKETING MANAGEMENT SOCOMEC SICON UPS Paris 95 rue Pierre Grange F 94132 Fontenay sous Bois Cedex FRANCE Tel 33 0 1 45 14 63 90 Fax 33 0 1 48 77 31 12 ups paris dcm socomec com www
4. failure UPS in back up mode do not disconnect the input cable from the mains so as to ensure earth connection to the powered loads e Al subsequent maintenance operations must be carried out solely and exclusively by authorized personnel Inside the system high electric voltages are generated which may endanger maintenance personnel who are not sufficiently prepared and trained for such tasks e f at any time a hazard condition is created during use disconnect the mains power supply if possible through the control panel upstream of the unit and shutdown the UPS completely following the appropriate procedure e When assembling and replacing the battery the UPS should always be switched off and disconnected from the mains power supply Do not dispose of batteries in a fire the battery may explode e CAUTION a battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries remove watches rings or other metal objects and use tools with insulated handles e The batteries constitute an internal power source for the UPS and mean that the system output may be powered even when the UPS is not connected to the mains power supply e Do not force break or try to open the batteries They are sealed and do not require any maintenance They contain substances that are toxic to health and that pollute the atmosphere Do not switch the UPS on if any leakage of liquid or
5. of any kind at any stage of their working life Block diagram The block diagram provides a useful aid to understanding how the machine operates Legend Mains input Battery charger Automatic Voltage stabilizer AVR models only Inverter DC AC Automatic transfer switch Batteries for back up extensions optional Output to power consumers NO oc WD Out 7 SECTION 1 9 2DKOOROO doc ER SIC N UPS NeTYS 1000 3000 VA Product Manual GENERAL DESCRIPTION 2 1 LED BASED CONTROL AND DISPLAY PANEL Visual indication of operating mode LED green 1 lit Z NORMAL MODE mains ok flashing NORMAL MODE AVR active LED yellow 2 flashing BATTERY MODE mains absent or abnormal flashing fast battery low LED red flashing alarm present lit fault LED 2 yellow flashing overload LED yellow flashing wide range input mode LED red flashing battery disconnected lit battery needs replacing E Battery LED bar capacity 96 25 steps m Load LED bar power 96 2596 steps Detailed alarm indication LED flashing 25 battery LED bar flashing Fan fault Detailed failure indication LED lit 25 of battery LED bar flashing Fan failure 50 of battery bar LED flashing Overtemperature stop All LEDs on battery bar flashing Shortcircuit 75 of battery bar LED flashing Output voltage abnormal 100 of battery LED bar flashing abnormal battery recharge
6. socomec sicon com
7. 0 doc dyd OPERATING MODES S ICON ups NeTYS 1000 3000 VA Product Manual 5 OPERATING MODES NORMAL MODE When mains power is available and the voltage falls within the acceptable range the NORMAL MODE LED on the front panel remains on permanently In this mode the loads are powered from the mains power supply either directly or through the AVR stabiliser which intervenes in cases of voltage peaks The batteries are constantly recharged BATTERY MODE The UPS switches automatically to this operating mode when mains power fails spikes or lengthy black outs or if the mains is at a value considered to be dangerous the consumers are powered using the energy stored in the batteries converted to AC voltage through the inverter In this mode a slow intermittent acoustic alarm sounds while the BATTERY MODE LED on the front panel flashes In cases of prolonged mains failure the UPS powers the consumers until it shuts down when the batteries are fully depleted see the chapter on COMMUNICATION for orderly shutdown via software Just before shutdown when the battery charge runs out fully low battery charge is signalled via a rapid intermittent acoustic alarm The UPS automatically returns to normal operating mode about two seconds after the mains power is restored The time taken to transfer from normal to battery mode and vice versa is imperceptible to the load OVERLOAD The UPS can power loads up to the power rating declared on the m
8. Acoustic alarms 9 Intermittent alarm every 4 seconds BATTERY MODE Intermittent alarm every second battery low Intermittent alarm every second overload if X LED is flashing Continuous alarm UPS failure see detailed failure indication 6 SECTION 1 Pa SICON ups NeTYS 1000 3000 VA Product Manual 2 UNPACKING AND INSTALLATION 3 UNPACKING AND INSTALLATION 3 1 UNPACKING Remove the UPS and all the accessories that come with it cables CD ROMs etc from its packing case It is always advisable to keep the original packaging that has been specially designed for safe transport in case the unit has to be moved again 3 2 ENVIRONMENTAL REQUIREMENTS FOR INSTALLATION Install the UPS after first checking the following NeTYS has been designed for use in closed environments Place the UPS on a flat and stable surface in a ventilated environment away from heat sources and exposure to direct sunlight Keep ambient temperature between 0 C and 40 C and humidity less than 90 non condensing the best temperature to guarantee longest possible battery life is 15 20 C Ensure that the environment where the UPS will be installed is not dusty and leave a space of at least 20 cm around it to allow for adequate ventilation and access to the rear panel Make sure not to place the UPS or any other heavy object on the cables Check that the voltage and frequency preset for operation is right for your electrical pow
9. Mode Frequency Wave form Transfer time Normal Mode protections Battery Mode protections Load connection socket IEC 320 BATTERY Typical back up time Battery recharge COMMUNICATION Communication interface Ethernet adapter Local communication software Local and remote communication software Data line protection ENVIRONMENT Noise level normal mode Temperature Environment Reference standards WEIGHT AND DIMENSIONS Dimensions WxDxH mm Dimensions WxDxH mm 2U RM Net weight selecting wide mode 1500 2000 3000 models 2DKOOROO doc NeTYS 1000 3000 VA Product Manual TECHNICAL DATA 1500 MT 2000 MT 3000 RT 1500VA 1000W 2000VA 1340W 3000VA 2100W 1000 MT 1000VA 700W 160 276 V 230V nominal 50 60 Hz with automatic selection IEC320 10A IEC320 16A 300V 230 6500 A 300V 460j 6500 A The AVR increases boost 1 the output voltage by 15 when the input voltage drops below 90 of the nominal value The AVR decreases bucks the output voltage by 1296 when the input voltage rises above 11096 of the nominal value 230V 5 10 after battery low 50 60 Hz Sinusoidal 2 4 milliseconds typical overload 110 for 3 minutes shortcircuit protected overload 110 for 30 seconds shortcircuit protected 8 10 6 10A 1 16 8 min 8 min 8 min 8 min 4 hours 80 Cn after full discharge Under permanent charge even when the UPS is off mains present
10. PRODUCT MANUAL MANUEL DU PRODUIT MANUALE DI PRODOTTO PRODUKT HANDBUCH MANUAL DE PRODUCTO NEI YS UNINTERRUPTIBLE POWER SUPPLY UPS ALIMENTATION SANS tj rued yen SISTEMA DI CONTINUIT UPS UNTERBRECHUNGSFREIE STROMVERSORGUNG USV SISTEMA DE ALIMENTACI N ININTERRUMPIDA SAI Ze 4 5 6 7 2 2DKOOROO doc NeTYS 1000 3000 VA OMEC ups SIE Product Manual NeTYS PR 1000 3000 VA PRODUCT MANUAL SAFETY STANDARDS GENERAL DESCRIPTION 2 1 UNPACKING AND INSTALLATION 3 1 UNPACKING S 3 3 CONFIGURATION AND START UP OPERATING MODES COMMUNICATION MAINTENANCE 7 1 TECHNICAL DATA LED BASED CONTROL AND DISPLAY PANEL ENVIRONMENTAL REQUIREMENTS FOR INSTALLATION CONNECTION TO THE MAINS POWER SUPPLY AND CONNECTING THE LOAD REMEDIES FOR MINOR PROBLEMS CONTENTS OC 2DKOOROO d SOCOMEC x SAFETY STANDARDS Pa SICON ups NeTYS 1000 3000 VA Product Manual CERTIFICATE AND CONDITIONS OF WARRANTY This SOCOMEC SICON UPS uninterruptible power system is guaranteed against manufacturing and material defects for a period of 24 months from the date of purchase and not however more than 27 months from the date of shipment by SOCOMEC SICON UPS The warranty is of the carry in type free supply of parts and labour for repairs with return of a product to be replaced to SOCOMEC SICON UPS or authorized centres at the customer s cost and risk In order to use the warranty service the user m
11. TION OF THE OUTPUT VOLTAGE BATTERY EXPANSION UNITS WARNING The factory default configuration for the NeTYS PR model is for operation with an output voltage of 230V without any additional battery expansion units No configuration is required for normal use with standard back up Parameter settings Input mode normal 184 276 wide range 160 276V Output voltage 220 230 240 V Battery expansion units 0 1 2 are configured using free UPS communication software that can be downloaded from www socomec sicon com If wide range has been configured the yellow LED D will come flashing Configuration from mimic panel Output voltage and Battery expansion parameters are also settable by mimic panel following the below procedure Output voltage configuration ga push 240 V 3 seconds to start the procedure 230 V First is current setting 230 V led flashing 220 V 2 push again second is 240 V flashing push again third is 220 V flashing ENTER push 3 seconds to confirm at the same time change to Battery extentions configuration menu After Output voltage configuration Battery expansion configuration menu A ech First is 0 expansion only UPS led flashi A i d is 1 expansion led flashing push third is 2 expansion led flashing 2 battery expansion 1 battery expansion 0 no battery expansion ENTER push 3 seconds to confirm configuration and exit SECTION 1 9 2PK00R0
12. achine s data plate once this limit is exceeded the machine goes into overload condition Overloads are signalled by a rapid sounding acoustic alarm 2 Warning Significant overloads could cause permanent damage to the UPS Avoid connecting laser printers that generate absorption peaks liable to cause overloads on the UPS SELF TEST In NORMAL MODE when the button is pressed for more than five seconds a procedure is run to check battery and inverter operation If everything is working properly the UPS automatically returns to NORMAL MODE if not the test is suspended and the battery failure is reported through the Battery failure LED If the test fails however it is recommended that you leave the battery to charge overnight and repeat the test the next day It is advisable to perform the test with the batteries fully charged LED bar fully lit up 10 SECTION 1 OC 2DKOOROO d SOCOMEC COMMUNICATION Pa SICON ups NeTYS 1000 3000 VA Product Manual 6 COMMUNICATION The UPS provides excellent protection against interruptions or imperfections in the mains power supply In these cases the computer load is powered by the UPS using battery power until this runs out Various software applications and communication options are available to optimise operation of the UPS and to correctly manage shutdown when back up power ends The status of the UPS can be monitored keeping track of all the mains failures and battery dis
13. charges so as to activate an automatic and orderly procedure to close the programs and shutdown the system When mains power returns the system will restart automatically All NeTYS models are equipped with RS232 and USB communication interface USB not available on the NeTYS PR 1000 model COMMUNICATION SOLUTIONS Depending on the model there are different types of connections and software compatibility as shown in the table below Uni Vision local management software for local shutdown of Windows amp Linux systems RS232 Free on http www socomec fr page uk lien prod ups htm Uni Vision Pro network management software for local and remote shutdown supports RS232 the major operating systems through Java Shutdown Client technology HID UPS management based on Windows embedded service ENTM NetVision Web SNMP manager for UPS control over LAN with TCP IP protocol Allows Web SNMP remote shutdown through Java Shutdown Client technology card BMS possibility to integrate the UPS with BMS Building Management Systems oris RS232 INTERFACE Communication with the server can take place directly via the RS232 interface In addition to local or networked shutdown it is possible to perform full monitoring of the electrical parameters regarding battery status and the automatic programming of the UPS start up and shutdown procedures For a complete description of the software features refer to the Uni Vision and Uni Vision Pro docu
14. d rear brakets for Rack assembling mode 6 VIEW SECTION SOCOMEC 8DK00R00 doc z ZSICON ups NeTYS PR 3000 VA migration from Tower to Rack 19 Optionals rails Rack fixing accesories VIEW SECTION Q 7 OMEC 2DKOOROO0 doc Je DE ICON UPS NeTYS 1000 3000 VA Product Manual SAFETY STANDARDS 1 SAFETY STANDARDS This manual must be kept next to the UPS so that the operator may consult it at any time for clarification on the correct use of the UPS Read the manual carefully before connecting the unit to the mains power supply and to the devices to be powered Before switching on the UPS Uninterruptible Power Supply the operator must be fully aware of the functions and positions of all the controls and of the technical and functional characteristics of the system in order to avoid any risk to persons and to the equipment e Before starting the unit must have an equipotential connection as established by the safety standards in force The earth cable of the UPS must be connected to an efficient earth point e f the unit is not earthed all devices connected to the UPS will not have an equipotential connection In this case the manufacturer declines all responsibility for damage or accidents caused by non observance of the aforementioned standards e This is pluggable type A equipment with battery already installed by the supplier it s operator installable and may be operated by layman e n case of power
15. er supply looking the data can be found on the data plate Use only the manufacturer supplied or recommended cables and accessories for connections to the RS232 USB serial interface The lateral brackets supplied must be mounted on models designed for installation in standard 19 cabinets It is recommended that the batteries be left to charge for 8 hours the first time the unit is used SECTION 1 9 OCOMEC 2PK00R00 doc UNPACKING AND Je La SIC N UPS NeTYS 1000 3000 VA Product Manual INSTALLATION 3 3 CONNECTION TO THE MAINS POWER SUPPLY AND CONNECTING THE LOAD Cables with the appropriate cross section and conforming to the safety standards in force should be used for connection to the mains and connection of the loads 1500 2000VA model only connect the UPS power cord to the mains power supply Connect the UPS power cord to the mains power supply The mains input may be connected using the cable that previously powered the server Connect the loads to the outlet sockets on the rear of the UPS Use the two IEC320 cables supplied for the output connections Use of the battery expansions optional on models 1500 2000 3000 PR Back up extension units are available on some models when long life battery operation is required By combining the UPS with one or maximum two battery expansion units back up times of up to 60 minutes may be obtained A Danger Make sure that the safety switch on the battery expansion unit is in the
16. he model number and the manufacturing serial number that can be found on the conformance and inspection certificate or on the data plate on the bottom of the UPS PROBLEM CAUSE SOLUTION The UPS works in battery mode even if Poor connection to the input Check the connection of the cable mains power is available mains to the UPS and to the mains outlet The mains voltage is No solution because mode of out of range operation is correct Input protection triggered Replace the input fuse with another blown fuse or automatic of the same type or reset the switch automatic switch Back up time shorter than expected Batteries not fully charged Leave the batteries to charge for 8 hours consecutively Batteries not working Have the batteries replaced by properly authorised personnel Overload on the load line Check that the load applied is not The UPS stalls goes into overload greater than the maximum permitted or reduce the load power alarm requirement IF THE EQUIPMENT IS TO BE LEFT IDLE FOR A LONG PERIOD WAIT FOR THE BATTERIES TO CHARGE FULLY BEFORE SWITCHING OFF WHILE THE UPS IS LEFT IDLE MAKE SURE THAT THE BATTERIES ARE RECHARGED FOR 24 HOURS AT LEAST ONCE EVERY 4 WEEKS 12 SECTION 1 SOCOMEC SICON urs 8 TECHNICAL DATA NeTYS PR Power INPUT Voltage Frequency Mains connection Spike protection IEC 61000 4 5 OUTPUT Voltage in Normal Mode with AVR Voltage in Battery
17. l 2 GENERAL DESGRIPTION NeTYS sure power supply for PC servers graphics stations and network devices The main purpose of the UPS is to protect sensitive and critical equipment from electrical disturbances that can compromise operation Black outs brown outs variations in voltage and frequency lightning electrostatic discharges and rapid over voltages are phenomena found in all office and industrial environments and which cause damage to the hardware and loss of data NeTYS is an Uninterruptible Power Supply designed to power computers and connected peripherals with the exception of any other electrical device such as household appliances television sets stereo systems and video recorders INTRODUCTION The characteristic feature of these UPS is the constant monitoring of the power supply which duly filtered and stabilised on models with AVR and if considered suitable is used to supply consumers In cases of a mains failure or if the mains is considered to be outside limits accepted by the load the inverter the heart of the UPS is activated immediately Drawing on the power stored in the batteries the inverter generates a voltage that instantly takes over from the mains without any disruption to the equipment connected During operation under emergency conditions the internal batteries discharge but are recharged again automatically when mains power returns Being hermetically sealed the batteries do not require maintenance
18. mentation USB INTERFACE In addition to the RS232 serial link it is also possible to establish communication directly through USB with the HID protocol when this is available in the operating system In this case no SW needs to be installed A standard USB cable is used and once this is connected it is recognised just as any normal peripheral The control parameters of the unit can be set directly via the operating system service menu Net Vision card x slot Net Vision permits direct connection of the UPS to a LAN RJ45 Ethernet and remote control of the UPS through TCP IP using a WEB browser For a complete description refer to the Net Vision documentation SECTION 1 9 11 2DKOOROO d er MAINTENANCE FER ISICON ups NeTYS 1000 3000 VA Product Manual 7 MAINTENANCE 7 1 REMEDIES FOR MINOR PROBLEMS This section examines some of most likely problems that can compromise correct operation of the UPS attempting to solve them and identifying the possible causes and remedies THE UPS INTERNALLY GENERATES HAZARDOUS ELECTRICAL VOLTAGES ALL MAINTENANCE MUST BE PERFORMED SOLELY AND EXCLUSIVELY BY AUTHORIZED PERSONNEL If you have difficulty in getting the UPS to work the reason may be among those listed below For any other problem you are advised to get in touch with your dealer or service organisation directly For quick and effective action when you call it is important to give precise details of the defect t
19. ordance with the terms indicated on the packaging and in the manual in cases of extended storage or UPS inactivity SOCOMEC SICON UPS may at its own discretion opt for the repair of the product or for the replacement of the faulty or defective parts with new parts or with used parts that are equivalent to new parts with regard to functions and performance Defective or faulty parts replaced free of charge are to be put at the disposal of SOCOMEC SICON UPS that becomes the sole owner Replacements or repairs of parts and any modifications to the product during the warranty period shall not extend the duration of the warranty In no case will SOCOMEC SICON UPS be responsible for damages including without limitations damage for loss of earnings interruption of activity loss of information or other economic losses deriving from the use of the product The present conditions are subject to Italian law Any dispute falls under the province of the Court of Vicenza For further information www socomec sicon com SECTION 1 9 FESICON UPS NeTYS PR 1000 VA NeTYS PR 1500 2000 VA NeTYS PR 3000 VA Rear view 77 ng 4 VIEW SECTION SOCOMEC 8DK00R00 doc
20. ust respect the following rules e the product must be returned exclusively in its original packaging Any damage caused during shipping in packaging other than the original is not covered by the warranty e the product must be accompanied by proof of purchase a document bill invoice receipt showing the date of purchase and the information necessary to identify the product model serial number The number of the authorization for return for repairs must also be attached with a detailed description of the defect found in the product If any of these elements is missing the warranty is invalid The return authorization number is issued by the service centres by telephone on receiving notification of the malfunction The warranty is recognised within Italian territory If the UPS is exported outside Italian territory the warranty shall be limited to the cover of the parts used to repair the fault The warranty shall not apply in the following cases e Failures due to fortuitous circumstances or force majeure lightning floods etc e Failures due to negligence or improper use use outside tolerance limits temperature humidity ventilation electric power supply applied load batteries e Insufficient or inadequate maintenance e Attempted maintenance repairs or modifications not carried out by SOCOMEC SICON UPS personnel or personnel from a support centre authorised by SOCOMEC SICON UPS e Ifthe battery has not been recharged in acc
21. white powder residue is noted e Replace batteries with the same number and type of batteries as originally installed in the equipment e Replace the fuses ONLY with other fuses of the same type e As the mains cable of the UPS is considered a disconnecting device the mains socket to which the UPS is connected and or the rear of the UPS must be accessible and easy to disconnect e Avoid contact of the UPS unit with water or liquids in general Do not introduce foreign bodies e f the unit needs to be scrapped it must be handed over solely and exclusively to specialist disposal companies These companies are obliged to break up and dispose of the various components in accordance with the national legal provisions in force e The UPS generates a leakage current of about 1 5 To guarantee the maximum limit leakage current of 3 5mA make sure that the maximum leakage current of the load is 2 mA If the load current exceeds this value have qualified personnel connect the UPS to an industrial type IEC 309 compliant power supply mains with a current of correct dimensions for the UPS power rating e NeTYS UPS is intended for commercial and industrial use it is not recommended for use in medical applications that are essential to the survival of the patient e Use the UPS in accordance with the technical specifications given in the User Manual 4 SECTION 1 OCOMEC 96 GENERAL DESCRIPTION Pa SICON ups NeTYS 1000 3000 VA Product Manua
22. z ZSICON urs 1 Fan air vents 2 Slot for optional communication boards 3 NTP protections RJ45 4 RS232 USB serial port 5 Battery connection for extension 6 UPS output sockets 7 Input socket and fuse 8 EPO emergency Power Off 1 Ventilatore griglia di ventilazione 2 Slot per schede di comunicazione opzionali 3 Protezione NTP RJ45 4 Connettore seriale RS232 USB 5 Connettore batteria per espansione esterna 6 Presa di uscita UPS 7 Presa ingresso rete e fusibile 8 EPO emergency Power Off 1 Ventilador tomas de aire 2 Slot para tarjetas de comunicaci n opcionales 3 Protecci n NTP RJ45 4 Conector serie RS232 USB 5 Conector de bater a para expansi n externa 6 Toma de salida SAI 7 Toma de entrada red y fusible 8 EPO emergency Power Off 1 Ventilateur prises d air 2 Cache pour cartes de communication optionnelles 3 Protection NTP RJ45 4 Connecteur s rie RS232 USB 5 Connecteur batterie pour extension externe 6 Prise de sortie ASI 7 Prise arrivee r amp seau et fusible 8 EPO emergency Power Off 1 L fter Bel ftungsanlage 2 Abdeckung f r Kommunikationskarten Option 3 Sicherung NTP RJ45 4 Serieller Anschlu RS232 USB 5 Batterieanschlu f r eine externe Erweiterung 6 Ausgang zur Last USV 7 Netzeingang und Sicherung 8 EPO emergency Power Off VIEW SECTION 5 SOCOMEC 8DK00R00 doc z ZSICON ups NeTYS PR 1500 2000 VA migration from Tower to Rack 19 Front an
Download Pdf Manuals
Related Search