Home

Bosch SPS59L12GB dishwasher

image

Contents

1. mil v 27 E 4 a JE 1 amp 3 Remove the lower spray arm upwards 4 Clean spray arms under running water 5 Re engage or screw on spray arms Fault what to do Experience has shown that you can rectify most faults which occur in daily operation yourself This ensures that the machine is quickly available to you again In the following overview you can find possible causes of malfunctions and helpful information for rectifying them Note If the appliance stops during dishwashing or does not start for no obvious reason first run the Abort programme function Reset See chapter entitled Operating the appliance A Warning Don t forget Repairs may be carried out by technicians only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump The rinsing water will then be above the filter A Warning Risk of cuts When cleaning the waste water pump ensure that you do not injure yourself on pieces of broken glass or pointed implements Fault what to do en In
2. which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils Programme sequence indicator my m Your dishes are being ay cleaned IN gt Your dishes are being rinsed m SS f Your dishes are being dried Remaining running time display When the programme is selected the remaining running time of the programme is indicated on the digital display C111 The running time is determined during the programme by the water temperature the number of utensils as well as the degree of soiling and may vary depending on the selected programme Timer programming depending on model You can delay the start of the programme in 1 hour steps up to 24 hours 1 Close the door 2 Switch on ON OFF switch L1 3 Press button until the digital display jumps to A i 4 Press or button until the displayed time corresponds with your requirements 5 Press START button L9 timer programming is activated 6 To delete timer programming press the or button until IT 4 00 is indicated on the digital display You can change your programme selection at any time until the programme starts End of programme The programme has ended when the value Lu is indicated on the numerical display C111 Operating the appliance en Automatic switch off after end of programme or i
3. 3 7 mmol l only If the water hardness is over 21 dH rinse aid must be used 1 Open the dispenser by pressing and lifting the plate on the cover 2 Carefully pour rinse aid up to the max mark in the filler opening 3 Close cover until it clicks shut 4 To prevent excessive foam formation during the next rinse cycle remove any rinse aid which has run over with a cloth Setting amount of rinse aid The amount of rinse aid can be set from to 7 06 Please set rinse aid on r d4 to obtain very good drying results IL ru is already set in factory Do not change the amount of rinse aid unless streaks select lower setting or water stains select higher setting are left on the utensils 1 Close the door 2 Switch on ON OFF switch 1 3 Hold down programme button and press START button L9 until 4 7 is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting H U4 5 Press programme button until the factory set value r 04 is indicated on the digital display 1 To change the setting 1 Press programme button LC Each time the button is pressed the set value increases by one level when the value of U amp has been reached the display jumps back tor off 2 Press START button 9 The set value is saved Switching off rinse aid refill indicator If the rinse aid
4. Folding spikes depending on model The spikes can be folded down to improve arrangement of pans bowls and glasses Small accessories holder depending on model Light weight plastic accessories e g cups lids etc can be held securely in the small accessories holder Adjusting the height of the basket The height of the upper utensils basket can be adjusted in 3 stages to create more space either in the upper or lower basket Appliance height 81 5 cm Top basket Bottom basket Setting 1 max Betting 2 max 1 Pull out the top basket out 2 To lower the basket press in the left and then the right lever on the outside of the basket In doing so hold the sides of the basket along the upper edge to prevent it from suddenly dropping Detergent en To raise the basket hold the basket on the sides of the upper edge and lift it up Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit A Detergent You can use tablets as well as powder or liquid detergents for dishwashers but never use washing up liquid The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling Tablets contain an adequately large amount of active ingredients for all clean
5. installed above or below these appliances en Safety instructions If you cannot obtain any information from the manufacturer you must not install the dishwasher above or below these appliances If you install a microwave oven above the dishwasher the microwave oven may be damaged Install built under or integratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability Do not install the appliance near heat sources radiators heat storage tanks cookers or other appliances which generate heat and do not install under a hob After installing the appliance ensure that the plug is easily accessible See Electrical connection Some models The plastic housing on the water connection contains an electric valve the connecting cables are in the supply hose Do not cut through this hose do not immerse the plastic housing in water In daily use Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Childproof lock door lock The description of the childproof lock is at the back in the envelope depending on model Childproof lock button lock You can secure your appliance from being unintentionally the programme terminated e g improper operation by children Activating the button lock 1 Start the required programme 2 Hold down the button for approx 4 s
6. instructions They refer to normal conditions and the water hardness set value H 7 4 Different influencing factors such as e g water temperature or line pressure may result in deviations Aqua sensor depending on model The Aqua sensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme If the Aqua sensor is active clean rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3 6 litres If the turbidity is greater the water is drained and is replaced with fresh water In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling 20 Switching on the appliance 1 Turn on the tap fully 2 Switch on ON OFF switch L1 The Eco 50 programme display flashes This programme remains selected if no other programme button is pressed The expected programme duration flashes on the digital display O0 3 Press the START button L9 The programme starts running Note for environmentally friendly operation of the dishwasher For ecological reasons the Eco 50 programme is preset whenever the appliance starts This conserves environmental resources and not least saves you money The Eco 50 programme is a particularly environmentally friendly programme According to EU regulation 1016 2010 it is the Standard programme
7. when switching on the appliance for the first time 3 Then add dishwasher salt not table salt or tablets The water is displaced and runs out Water softening system Special salt en As soon as the salt refill indicator on the fascia is lit top up the salt depending on model Using detergents with salt component If combined detergents with a salt component are used salt can usually be omitted up to a water hardness of 21 dH 87 fH 26 Clarke 3 7 mmol I If the water hardness is over 21 dH special salt must be used Switching off salt refill indicator water softening system If the salt refill indicator is impaired e g when using combined detergents containing salt component it can be switched off m Proceed as described under Adjusting the water softening system and set the value to HHD The water softening system and salt refill indicator are now switched off A Caution Never fill the salt dispenser with detergent You will destroy the water softening system 11 en Rinse aid Rinse aid As soon as the rinse aid refill indicator is lit on the fascia there is still a rinse aid reserve of 1 2 rinsing processes Refill with rinse aid The rinse aid is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Combined detergents with rinse aid component may be used up to a water hardness of 21 dH 37 fH 26 Clarke
8. Inthe case of free standing appliances ensure that the baskets are not overloaded a If the appliance is not in a cavity and a side panel is accessible the door hinge area must be covered at the side for reasons of safety risk of injury The covers are available as optional accessories from customer service or specialist outlets en Safety instructions A Warning Risk of explosion Do not add any solvents to the washing chamber Danger of explosion A Warning Risk of scalding Open the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance A Warning Risks to children If fitted use the childproof lock An exact description can be found in the back of the enve lope Do not allow children to play with or operate the appliance Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from open dishwasher The water in the rinsing compartment is not drinking water and could contain detergent residue Ensure that children do not place fingers in the tablet collecting tray 24 Small fingers could become caught in the slots When opening and closing the door on an eye level appliance ensure that children do not become jammed or crushed between the appliance door and the cupboard door below Children could become locked in the appliance danger
9. Spikes sons 4 04 2224244 14 Small accessories holder 15 Adjusting the height of the basket 15 AN Detergent 15 Adding detergent 16 Combination detergent 17 Overview of programmes 18 Programme selection 19 Information for test institutes 19 Additional options 19 Express Wash Speed Perfect VarioSpeed 0 000 eee 19 Half dad share ara 19 Hygiene ts tou una ee 19 Intensive ZONE nannaa aaan aana 19 Extra diyind naaa ann 19 Sy Operating the appliance 20 Programme data 20 Agua Sensor 4 warten 20 Switching on the appliance 20 Programme sequence indicator 20 Remaining running time display 21 Timer programming 4 21 End of programme 21 en Intended use Automatic switch off interior light 21 Switching off the appliance 22 Interrupting the programme 22 Terminating the programme 22 Changing the programme 22 Intensive drying 008 22 Cleaning and maintenance 23 Overall condition of the machine 23 Special salt and rinse aid 23 Fillers sce Wa a Blak ao ee ee ees BE ae 24 Spray arMS 2 eee es 24 Fault what todo 25 Waste water pump 25 Fault tablevcacc c a0 das cee heed on 26 Customer service 34 Installation and connection 34 Product package 34 Safety
10. as possible Use different combination detergent with better drying also increases the drying performance Activate inten appliance Wait until program ends or wait until 30 min after program utensils Use a proprie Q performance Use of rinse a sive drying see Operating the ends before removing ary rinse aid Eco products are much less effective Plastic has a Special properties of plastic Cutlery not dry Cutlery not arranged properly in and therefore ower heat storage capacity dries less well Separate cutlery if possible prevent contact the cutlery basket Cutlery not arranged properly in the cutlery drawer points Arrange cutle possible ry properly and separate if Appliance interior wet after No appliance fault On account of the Condensation drying principle water droplets are physically rinse cycle induced and r equired in the container The humidity in the air condenses on the inner walls of the di shwasher drains and is pumped out 28 Fault Food remnants on the utensils Detergent residue Cause Utensils placed together utensils overfilled oo closely basket Spray arm rotation obstructed Spray arm nozzles are blocked Filte n 27 dirty Filters L27 inserted incorrectly and or not engaged Rinse programme too weak Utensils precleaned too intensely sensors t
11. cutlery Initial or existing irreversible clouding of glass Cause Film forma ingredients ion consisting of from vegetables e g cabbage celery potatoes noodles componen aluminium or the tap water e g manganese Film formation caused by metallic s on silver or utensils Film forma ingredients from food remnants ion consisting of and substances from the tap water lime scale soapy Too low rinsing temperature Utensils precleaned too intensely sensors therefore decide on weak programme sequence Stubborn soiling cannot be completely removed Too much rinse aid No rinse aid added or setting too low Detergent residue in the final rinse programme section Detergent dispenser cover oO not open fu Hs completely only suitabl ocked by utensils cover does lly Utensils precleaned too intensely sensors therefore decide on eak programme sequence ubborn soiling cannot be removed Glasses not dishwasher proof e for dishwasher Fault what to do en Remedial action Can be partly removed with machine cleaner or by mechanical cleaning Coatings are harmless Can be partly removed with machin cleaner or by mechanical cleaning rap Check function of the water softening system refill with salt or if using combined detergents tablets activate water softening system see chapter Wa softe
12. indentations are at an angle thereby allowing water to drain they do not obstruct rotation of the spray arms and 25 Very small utensils should not be washed in the machine as they may fall out of the baskets Unloading the dishwasher To prevent water from dripping off the upper basket onto the utensils in the lower basket it is recommended to empty the appliance from the bottom up Hot utensils are sensitive to shock Therefore when the programme ends leave the utensils to cool down in the dishwasher until they can be handled Note When the programme ends water droplets can still be seen inside the appliance This does not affect the drying of the utensils 13 en Utensils Cups and glasses Top basket Pans Bottom basket Tip Heavily soiled utensils pans should be placed in the bottom basket The more powerful spray jet provides a better dishwashing result 14 Tip Other examples such as the best way of loading your dishwasher can be found on our homepage as a free download The corresponding Internet address can be found on the back page of these instructions for use Cutlery drawer Arrange the cutlery in the cutlery drawer as illustrated Separately arranged cutlery is easier to remove after washing The drawer can be taken out
13. not closed properly Do not place utensils or fragrance dispenser in the tablet collecting tray Top basket presses against the door and prevents door from being closed securely Power and or water supply interrupted Depends on domestic installation as appliance is not defective No effect on appliance function Spray arm strikes the utensils utensils not positioned correctly If there is a low load the water jets strike the washing tank directly Light utensils move during the wash cycle Handwash liquid in the rinse aid dispenser Rinse aid spilled Fault what to do en Remedial action Close the door Check whether rear panel is being pressed in e g by socket or by hose holder which has not been removed Restore power and or water supply No remedial action possible Position utensils so that the spray arms do not strike the utensils Load the appliance with more utensils or distribute the utensils more evenly in the dishwasher Arrange light utensils securely Immediately refill rinse aid dispenser with rinse aid Remove rinse aid with a cloth 33 en Customer service Customer service If you are unable to rectify the fault please contact your customer service We always find a suitable solution even to avoid unnecessary visits by technicians Contact information for your nearest customer service can be found on the back of these instruc
14. not fas ened firmly or salt was spilled while being refilled The mains fuse has tripped Power cord not inserted The appliance door has not been shut properly You did ended Child Door Door ca installa not wait until programme ock is activated ock has been activated nnot be closed due to ion Detergent dispenser or cover guide b residue Spray a ocked by sticky detergent rms blocked by utensils therefore detergent is not rinsed out The de ergent dispenser was damp when filled Remedial action Use corrosion resistant cutlery Do not wash rusting parts Fasten salt dispenser lock firmly or remove Spilled salt Check mains fuse Ensure that the power cord is plugged all the way into the back of the appliance and into the socket Check that the socket functions Close the door Perform reset See Terminating the programme Deactivate child lock See instructions for use at the back Close door with increased force Check appliance installation Door or attached parts must close without obstruction Remove detergent residu D Ensure that the spray arms can rotate freely Pour detergent into the dry detergent dispenser only Fault Appliance stops in the programme or programme is interrupted Filling valves making striking noises Knocking or rattling noise Unusual foam formation Cause Door
15. of suffocation or get into another dangerous situation Redundant appliances Pull out the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed Protection of the environment Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials Please dispose of the individual parts separated according to type Please ask your dealer or inquire at your local authority about current means of disposal Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations e g gt PS lt polystyrene Therefore plastic waste can be sorted out when the appliance is being disposed of Please follow the safety instructions under Delivery Old appliances Please follow the safety instructions under Disposal of your appliance This appliance is labelled in R accordance with European mae Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Protection of the environment en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in th
16. refill indicator is impaired e g when using combined detergents containing rinse aid component it can be switched off m Proceed as described under Setting amount of rinse aid and set the value to r ad The rinse aid refill indicator is now switched off Utensils Not suitable Cutlery and utensils made of wood Delicate decorative glasses craft and antique utensils These decors are not dishwasher proof Plastic parts not resistant to heat Copper and tin utensils m Utensils which are soiled with ash wax lubricating grease or ink Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass e g crystal glass objects may turn cloudy after many wash cycles Glass and utensil damage Causes Glass type and glass production process Chemical composition of the detergent Water temperature of the wash programme Recommendation m Use only glasses and porcelain which the manufacturer designates as dishwasher proof Use a detergent which protects utensils Take glass and cutlery out of the dishwasher as soon as possible after the programme ends Utensils en Loading the dishwasher 1 Remove large food remnants It is not necessary to prerinse utensils under running water 2 Place the utensils so that they are secure and cannot tip over all utensils with their openings face down parts with curves or
17. Notes You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately f programmes are short tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue It is recommended to use washing powder for these programmes The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning agent to the inside of the appliance s door Even if the rinse aid and or salt refill indicator is lit the rinse programme will run correctly with combined detergents If using detergents in a water soluble protective cover Take hold of the cover with dry hands only and put the detergent into an absolutely dry detergent dispenser only otherwise the detergent may stick f you switch from combined detergents to solo detergents ensure that the water softening system and amount of rinse aid have been set to the correct value 17 en Overview of programmes Overview of programmes The max possible number of programmes is illustrated in this overview The corresponding programmes and their arrangement can be found on the fascia Type of utensils Type of soiling Programme Possible Programme sequence additional options Prerinse a 5 Hiean TO pots and pans very adhesive burned o TTA Al Intermediate rinse non sensi
18. Register your new Bosch now www bosch home com welcome Dishwasher SP BOSCH en Instruction manual El DO FPO Po E No gt N co SE 25 m en 7 i al N hr 4 Pa Sanus nc M a i z N NANN g Table of contents Intended use Safety instructions Before you switch ON the appliance Delivery un state nal Installation 2 aa eee ndail USE ser ee Door lock Button lock 0 cee eee Damage Disposal Protection of the environment Packaging crre Hac 8 ete ren Old appliances 205 Getting to know your appliance Control panel Appliance interior Overview of menu 06 Water softening system Special salt Setting Water hardness table Using special salt Detergents with salt component Switching off water softening system Ea Rinse aid Setting amount of rinse aid Switching off rinse aid refill indicator Utensils en AREENA RARESA 13 Not suitable naana anaa aaa aaa 13 Glass and utensil damage 13 Loading the dishwasher 13 Unloading the dishwasher 13 Cups and glasses 14 Panse aan ate tod Aiea Oe yale o 14 Cutlery drawer 0005 14 Folding
19. Turn off the tap not applicable if Aqua Stop fitted 3 Remove the utensils when they have cooled down Note When the programme ends leave the appliance to cool down a while before opening it This will prevent steam from escaping and causing long term damage to your built in furniture Interrupting the programme 1 Switch off ON OFF switch 1 The LEDs go out The programme is saved If the door was opened on an appliance which has a warm water connection or is heated first leave the door ajar for several minutes and then close Otherwise expansion pressure may cause the appliance door to spring open or water to run out of the appliance 2 To continue the programme switch on the ON OFF switch again 22 Terminating the programme Reset 1 Press START button L9 for approx 3 sec The numerical display indicates 2 0 i 2 The programme sequence lasts approx 1 min On the digital display is indicated 2 37 3 Switch off ON OFF switch 1 Changing the programme When the START button L9 has been pressed the programme cannot be changed The only way a programme can be changed is by Cancel programme Reset Intensive drying The final rinse uses a higher temperature which improves the drying result The running time may increase slightly Caution if utensils are delicate 1 Close the door 2 Switch on ON OFF switch L1 3 Hold down programme button and press START button 9 unti
20. ckaging and its parts There is a risk of suffocation from collapsible boxes and film Installation Following installation ensure that the back of the dishwasher is not freely accessible protection against contact due to hot surface Install and connect the appliance according to the installation and assembly instructions Prior to installation disconnect the dishwasher from the power supply Ensure that the protective conductor system of the domestic supply has been correctly installed Safety instructions en The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 32 If the power cord of this appliance is damaged it must be replaced with a particular power cord To prevent injury the power cord may be purchased from customer service only lf the dishwasher is installed in a high sided unit the unit must be secured properly If the dishwasher is installed below or above other domestic appliances follow the information for installation in combination with a dishwasher in the installation instructions for the particular appliances Also follow the installation instructions for the dishwasher to ensure that all appliances are operated safely If there is no information or if the installation instructions do not include the appropriate information contact the manufacturer of these appliances to ensure that the dishwasher can be
21. e text Control panel ON OFF switch Programme buttons Display Check water supply Salt refill indicator Rinse aid refill indicator Door opener Timer programming Additional options L9 START button 10 Programme sequence indicator C1 Digital display depending on model Number depending on model SEAR ARE en Water softening system Special salt Appliance interior L20 Interior light L21 Cutlery drawer 22 Top basket 23 Upper spray arms 24 Tablet collecting tray 125 126 L27 Bottom spray arm Dispenser for special salt Filters 28 Bottom basket 29 Dispenser for rinse aid 30 Detergent dispenser 1 Lock for detergent dispenser 32 Rating plate depending on model Overview of menu The settings can be found in the individual chapters H Water Hardness 4 00 4 07 g Intensive drying 00 Be ul r Rinse aid riu OG iE A Hot water HH u Ap i a3 P Automatic disconnection F 00 P le Water softening system Special salt To ensure good washing results the dishwasher requires soft water i e containing low amounts of lime otherwise white limescale will be deposited on the utensils and inner container Tap water above 1 2 mmol l must be softened The water is softened with special salt regeneration salt in the water softening system of the dishwasher The setting and th
22. ec until this L is indicated on the digital display If any button is pressed while the programme is running this LL is indicated on the digital display It is not possible to end Reset the programme Deactivating the button lock Hold down the button LB for approx a sec until the display Li goes out When the programme ends 4 0 on the digital display the button lock is cancelled If there is a power failure the button lock is retained Whenever a programme is restarted the button lock must be reactivated Damage The appliance may be repaired and opened up bya technician only To do this disconnect the appliance from the power supply Pull out the mains plug or switch off the fuse Turn off the tap a lf the appliance is damaged especially the fascia cracks holes broken buttons or the door function is impaired stop operating the appliance Pull out mains plug or switch off fuse Turn off tap call customer service Safety instructions en Disposal 1 Make redundant appliances unusable to prevent subsequent accidents 2 Dispose of the appliance in a n environmentally friendly manner A Warning Risk of injury To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Knives and other utensils with sharp points must be placed horizontally in the cutlery drawer Do not lean or sit on the open door
23. ensure that it is in working order This may cause small water stains These will disappear after the first wash cycle Technical specifications Weight max 45 kg Voltage 220 240 V 50 Hz or 60 Hz Connected load 2 0 2 4 kW Fuse 10 16 A UK 13A Power input switched off 0 10 W not switched off 0 10 W Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature cold water hot water max temperature 60 C Capacity 9 10 place settings depending on model Installation and connection en Installation The required installation dimensions can be found in the installation instructions Level the appliance with the aid of the height adjustable feet Ensure that the appliance is situated securely on the floor A built under or integrated appliance which is installed subsequently as a free standing appliance must be secured to prevent it from overturning e g by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards The appliance can easily be installed in a fitted kitchen between wooden and plastic walls Waste water connection 1 The required work sequence can be found in the installation instructions If required fit a siphon with an drainage connection 2 Connect the waste water hose to the draina
24. er damage protection system Please note the system will not function unless the power supply is connected Installation and connection en Removing the appliance Also observe the sequence of worksteps here 1 2 3 Disconnect the appliance from the power supply Turn off the water supply Undo the waste water and drinking water connection Loosen fastening screws for the furniture parts If fitted remove the base panel Pull out the appliance carefully pulling the hose behind 37 en Installation and connection Transportation Empty the dishwasher and secure loose parts Drain the appliance according to the following steps 1 Turn on the tap 2 Close the door 3 Switch on ON OFF switch 1 4 Select programme with the highest temperature The expected programme duration is indicated on the numerical display Ci 5 Press START button LQ Programme sequence starts 6 After approx 4 minutes press the START button 9 until 7 7 is indicated on the digital display After approx 1 min 0 05 is indicated on the digital display 7 Switch off ON OFF switch L1 8 Turn off the tap disconnect supply hose and drain water Transport appliance upright only This prevents residual water from running into the machine control and damaging the programme sequence 38 Protection against frost If the appliance is in a room where there is a risk of frost e g hol
25. erefore the required amount of salt depends on the degree of hardness of your tap water see table Setting The amount of salt dispensed can be set from Hgg to HT u I Salt S not required at the set value HD go 1 Find out about the hardness value of your tap water Your water utility company will help you with this 2 Set value can be found in the water hardness table 3 Close the door 4 Switch on ON OFF switch L1 5 Hold down programme button and press START button 9 until H O is indicated on the digital display 6 Release both buttons The LED for button flashes and the digital display displays the factory setting 4 2 To change the setting 1 Press programme button LC Each time the button is pressed the set value increases by one level when the value of 4 07 has been reached the display jumps back to WH off 2 Press START button 9 The chosen setting has now been stored Water hardness table Set value on the machine Hardness I range I 3 15 ium 1 9 2 1 j medium 2220 Eeo 30 37 27 38 hard 3 8 5 4 5 5 8 9 Ta m 39 62 hard Using special salt Always refill with special salt immediately before switching on the appliance This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank 1 Open the screw type cap of the compartment 26 2 Fill the tank with water only required
26. ge connection of the siphon with the enclosed parts Ensure that the drainage hose is not kinked crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out 35 en Installation and connection Drinking water connection 1 Fasten the drinking water connection to the tap according to the installation instructions using the enclosed parts Ensure that the drinking water connection is not kinked crushed or twisted 2 When replacing the appliance always use a new water supply hose Water pressure At least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate Minimum 10 litres minute Water temperature Cold water preferred hot water max temperature 60 C 36 Warm water connection depending on model The dishwasher can be connected to cold or hot water up to max 60 C Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a Suitable installation e g solar heating system with circulation line This will save energy and time The hot water setting 4 2 allows you to adjust your appliance optimally to operation with hot water It is recommended to have a water temperature temperature of the incoming water of at least 40 C and no more than 60 C It is not recommended to connect the appliance to h
27. herefore decide on wea programme sequence Stubborn soiling cannot be completely removed Tall narrow receptacles in corner areas are not rinsed adequately Top basket 22 on right and left not set to same height Detergent dispenser cover bloc ed by utensils and therefore does not open fully Detergent dispenser cover blocked by the tablet Tablets used in th programme Dissolving time o is not reached in short programme e quick or short the detergent he selected Washing effect and dissolving performance are educed after a prolonged storage time or detergent is very umpy Fault what to do en Remedial action Arrange utensils with adequate clearance between them ensuring hat the spray jets can reach the surface of the utensils Prevent contact points Arrange utensils so that rotate without obstruction Clean the spray arm nozzles see Clean he spray arm can ing and maintenance Clean filters see Cleaning and maintenan Inse ce t and engage filters correctly Select a more intensive rinse programme Do not prerinse utensils Remove only large food remnants Recommended programme Eco 50 or Intensive Do not p ace hollow receptacles too obliquely and do not place in the corner area Set leve op bas rs et to same height using side Detergent dispenser cover must no
28. iday home empty the appliance completely see Transportation Subject to changes Childproof lock door lock AWarning 40 Activate the childproof lock Always close the appliance door completely 41 Open the door with activated when you leave the appliance childproof lock This is the only way you can protect your 42 Deactivate childproof lock children from potential dangers Baking sheet spray head 7 Large sheets or grilles and plates which have a diameter greater than 30 cm gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the diagram To ensure that the spray jet can reach all parts arrange the baking sheets as illustrated max 2 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models AquaStop guarantee does not apply to appliances without AquaStop In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions 1 If our AquaStop system is defective and causes water damage we will make good the damage for private users To ensure water damage
29. ing tasks Modern powerful detergents predominantly use a low alkaline formulation with phosphate and enzymes Phosphates bond the lime in the water Enzymes break down starch and remove protein Phosphate free detergents are less frequent These have a slightly weaker lime bonding capacity and require a higher dosage To remove coloured stains e g tea tomato sauce oxygen based bleaching agents are usually used 15 en Detergent Note To ensure a good washing result always follow the instructions on the detergent packaging If you have further questions we recommend that you contact the detergent manufacturers helpline A Warning Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Adding detergent 1 If the detergent dispenser is still closed press the lock to open the detergent dispenser Pour detergent into the dry detergent dispenser only insert tablet flat not on its edge Dosage see manufacturer s instructions on the packaging The graduated detergent dispenser helps you add the correct amount of powder or liquid detergent Usually 20 ml 25 ml are adequate for normal soiling If using tablets one tablet is adequate 2 Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty The detergent dispenser opens automatically at the optimum time depending on the progra
30. instructions 34 DEINEN aaa aan 35 Technical specifications 35 Installation 0 0 0 000005 35 Waste water connection 35 Drinking water connection 36 Warm water connection 36 Electrical connection 37 Removing the appliance 37 Transportation 005 38 Protection against frost Emptying the appliance 38 Intended use This appliance is intended for use in the home and the home environment Use the dishwasher only in the household and only for its designed purpose for washing domestic dishes Safety instructions Children from 8 years of age or people whose physical sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person Before you switch ON the appliance Please read the operating and installation instructions carefully They contain important information on how to install use and maintain the appliance Retain all documents for subsequent use or for the next owner Delivery 1 Check the packaging and dishwasher immediately for damage caused in transit Do not switch on a damaged appliance but contact your supplier Please dispose of the packaging material in an environmentally friendly manner Do not let children play with pa
31. l the digital display HD is indicated 4 Release both buttons The LED for button flashes and the digital display displays the factory setting H H 5 Press programme button until the factory set value 0 07 is indicated on the digital display IT To change the setting 1 Press the button to switch the Intensive drying on 0 i or off hl 2 Press START button 9 The set value is saved Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems Overall condition of the machine m Check spray arm for grease and limescale deposits If you find such deposits Fill detergent dispenser with detergent Start the appliance without utensils in the programme with the highest rinsing temperature Clean the appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers To ensure that the door seal always remains clean and hygienic regularly clean it with a damp cloth and a little washing up liquid lf the appliance is switched off for a prolonged period leave the door ajar to prevent the formation of an unpleasant odour Cleaning and maintenance en Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and fascia with a damp cloth water and a little washing up liq
32. mme The powder or liquid detergent is distributed in the appliance and is dissolved the tablet falls into the tablet collecting tray where it dissolves in doses Tip If the utensils are only lightly soiled slightly less than the indicated amount of detergent is usually adequate Suitable detergents and care products can be purchased online via our website or via customer service see back page Combination detergent Apart from conventional detergents Solo a number of products are offered with additional functions These products contain not only the detergent but also rinse aid and salt replacement substances 3in1 and depending on the combination 4in1 5in1 etc additional components such as glass protection or stainless steel cleaner Combination detergents function only up to a specific degree of hardness usually 21 dH Over this limit salt and rinse aid must be added As soon as combined detergents are used the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result A Warning Do not place small parts for washing in the tablet collecting tray 24 this prevents the tablet from dissolving evenly A Warning If you want to add more utensils after the programme has started do not use the tablet collecting tray as a handle for the upper basket The tablet could already be there and you will touch the partially dissolved tablet Detergent en
33. ning system Special salt Select programme with higher washing temperature Do not prerinse utensils Remove only large food remnants Recommended programme Eco 50 cD r Set rinse aid amount to lower setting Add rinse aid and check dosage recommended setting 4 5 Detergent dispenser cover must not be obstructed by utensils Do not place utensils or fragrance dispenser in the tablet collecting tray Do not prerinse utensils Remove only large food remnants Recommended programme Eco 50 Use dishwasher proof glasses Avoid long steam phase standing time after wash cycle ends Use wash cycle at lower temperature Set water softening system according to the water hardness if required one setting lower Use detergent with glass protection component 31 en Fault Rust spots on the cutlery Appliance does not start Programme starts automatically The door is difficult to open Door cannot be closed Cover on the detergent dispenser cannot be closed Detergent residue in the detergent dispenser or in the tablet collecting tray 32 Fault what to do Cause Cutlery not adequately rust resistant Knife blades are frequen affected Cutlery parts a tly more severely will also rust if rusting e rinsed at the same time pan handles damaged utensil baskets etc Sa content in the rinsing water too high as salt dispenser lock
34. ns can be set with the buttons 8 G Express Wash Speed Perfect VarioSpeed This function can reduce the running time by approx 20 to 50 depending on the selected rinse programme The change in the running time is indicated on the digital display LIT To obtain optimum cleaning results at a reduced running time water and energy consumption are increased Additional options en Half load If you have only a few items to wash e g glasses cups plates you can switch to half load This will save water energy and time It is recommended to put a little less detergent in the detergent dispenser than for a full load Hygiene The temperature is increased during the cleaning process This increases the hygiene status This additional option is ideal for cleaning e g chopping boards and baby bottles Intensive zone Perfect for a mixed load You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket The spray pressure in the lower basket is intensified the rinsing temperature is increased slightly Extra drying An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better There is a slight increase in the energy consumption 19 en Operating the appliance Operating the appliance Programme data The programme data consumption values can be found in the summary of
35. nterior light depending on model To save energy the dishwasher can be automatically switched off 1 min or 120 min after the programme ends The setting can be selected from 7 37 to F De PF Appliance does not switch off automatically The interior light comes on when the door is opened irrespective of whether the ON OFF switch is switched on or off When the door is closed the light is off If the door is open for longer than 60 min the light switches off automatically The interior light 20 is lit only when the set value 7 07 is selected PF Appliance switches off after 1 min P ui Appliance switches off after 120 min 1 Close the door Switch on ON OFF switch L1 3 Hold down programme button and press START button L9 until 4 7 is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting H U1Y 5 Keep pressing programme button LA until the value 7 77 is indicated on the numerical display 17 N 21 en Operating the appliance To change the setting 1 Press programme button LC Each time the button is pressed the set value increases by one level when the value of F 02 has been reached the display jumps back to Pod 2 Press START button 9 The set value is saved Switching off the appliance Short time after the end of the programme 1 Switch off ON OFF switch 1 2
36. om closing Refill indicator for salt 4 No rinse aid Refill rinse aid and or rinse aid LS Tis lit No salt Refill with special salt Sensor does not detect salt Use different special salt tablets Refill indicator for salt 4_ Refill indicator switched off Activation deactivation see chapter Water and or rinse aid isnot softening system Special salt or Rinse aid lit There is still enough special salt Check refill indicator levels rinse aid available Water is left in the Filter system or area under the Clean filters and area underneath see appliance at the end ofthe filters L27 is blocked Waste water pump programme Program has not ended yet Wait until programme ends or reset see Terminating the programme 27 en Fault Fault what to do Cause Remedial action Refill rinse aid Utensils not dry Plastic utensils not dry No or too little rinse aid in the dispenser Programme selected without drying Water collecting in depressions on the utensils and cutlery The combined detergent used has a poor drying performance Intensive drying to increase drying not activated Utensils were removed too early or drying process had not ended yet The eco rinse aid used has a poor drying performance Select progra mme with drying see Overview of programmes Programme sequence Arrange utensils in a sloping position arrange affected utensils as sloping
37. ot water if the water is supplied from an electric boiler Setting hot water 1 Close the door 2 Switch on ON OFF switch L1 3 Hold down programme button and press START button L9 until 4 7 is indicated on the digital display 4 Release both buttons The LED for button flashes and the digital display displays the factory setting H H 5 Press programme button until the factory set value A is indicated on the digital display 11 To change the setting 1 By pressing the LC button you can switch the hot water setting off 7 02 or on Ad 2 Press START button 9 The set value is saved Electrical connection Connect the appliance to an alternating current only ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor See rating plate for required fusing 32 The socket must be near the appliance and freely accessible following installation If the plug is not freely accessible an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions The connection may be modified by technicians only A power cord extension may be purchased from customer service only Use only a residual current operated circuit oreaker which features the symbol Gx Only this extension guarantees compliance with the currently valid regulations The appliance features a wat
38. ply is open Switch off the appliance and pull out the mains plug Turn off the tap Unscrew water connection Clean filter in the supply hose Screw water connection on again Check for leaks Reconnect power supply Switch on the appliance Arrange utensils so that the intake opening is not obstructed Clean appliance with dishwasher cleaning agent or descaler Operate the dishwasher with water softening system and check the setting see chapter Water softening system Special salt Clean filters see Cleaning and maintenance nstall hose without kinks remove any esidue Check connection to siphon and open if equired Lock cover correctly See Waste water pump Clean pump and lock cover correctly See Waste water pump Not an appliance fault have the mains voltage and electrical installation checked Fault what to do en Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON OFF indicated on the digital occurred switch 1_ After a short time restart the display appliance 6 0 itoE 30 If the problem recurs turn off the tap and pull out the mains plug Call customer service and mention the error code Display flashes Door not closed properly Close the door Ensure that no objects utensil fragrance dispenser are protruding over the basket and preventing the door fr
39. protection the appliance must be connected to the power supply 2 This liability guarantee is valid for the service life of the appliance 3 A prerequisite for the warranty claim is that the appliance has been correctly installed and connected with AquaStop according to our instructions This also includes the correct installation of the AquaStop extension original accessory Our warranty does not extend to defective feed lines or fittings up to the AquaStop connection on the tap 4 If your appliance is fitted with AquaStop you can leave your appliance unattended during operation and leave the tap turned on afterwards The tap should only be turned off if you are absent from home for a prolonged period e g several weeks holiday Z Repair order and advice on faults GB 0844 892 8979 Calls from a BT landline will be charged at up to 3 pence per minute A call set up fee of up to 6 pence may apply IE 01450 2655 0 03 per minute at peak Off peak 0 0088 per minute US 800 944 2904 toll free Contact information for all countries can be found on the enclosed customer service list Robert Bosch Hausger te GmbH Carl Wery Stra e 34 81739 M nchen Germany www bosch home com 9000869802 en 9405 440MG
40. t be obs ructed by utensils Do not place utensils or fragrance dispenser in th Tab et mus e tablet collecting tray be inserted flat and not upright Dissolving time of tablets too long for a quick or short programme Use a detergent powder or select a more intensive programme Change detergent 29 en Fault what to do Fault Water stains on plastic parts Washable or water soluble coatings in the container or on the door White stubborn coatings limescale on the utensils container or door Tea or lipstick residue on the utensils 30 Cause Droplet formation on plastic surface is physically unavoidable After drying water stains are visible Detergent substances are deposited These coatings cannot usually be removed with chemicals appliance cleaner If there is a white coating on the container floor the water softening system has been set marginally Salt dispenser cover not closed Only for glasses Initial glass corrosion can only apparently be wiped off Detergent substances are deposited These coatings cannot usually be removed with chemicals appliance cleaner Hardness range incorrectly set or water hardness greater than 8 9 mmol l 3in 1 detergent or bio eco detergent not effective enough Underdosing of detergent Too weak rinse programme selected Too low rinsing temperature Too little or unsuitable de
41. tergent Utensils precleaned too intensely sensors therefore decide on weak programme sequence Stubborn soiling cannot be completely removed Remedial action Use a more intensive programme more water changes Arrange utensils in a sloping position Use rinse aid If required increase softening setting Change detergent brand Clean appliance mechanically Increase softening setting and change detergent if required Close salt dispenser cover correctly See Glass and utensil damage Change detergent brand Clean appliance mechanically Set water softening system according to instructions for use or top up salt Set water softening system according to instructions for use or use separate detergents proprietary detergent salt rinse aid ncrease detergent dosage or change detergent Select a more intensive rinse programme Select programme with higher washing temperature Use suitable detergent at correct dosage Do not prerinse utensils Remove only large food remnants Recommended programme Eco 50 Fault Coloured blue yellow brown difficult to remove to non removable coatings in the appliance or on Stainless steel utensils Coloured yellow orange brown easily removable deposits inside the appliance mainly in the floor area Plastic parts discoloured Removable streaks on glasses glasses with metallic appearance and
42. this case 1 First always disconnect the appliance from the power supply 2 Take out top basket and bottom basket 28 3 Remove the filters 27 4 Scoop out water use a sponge if required 5 Prise out the white pump cover as illustrated using a spoon Grip the cover on the crosspiece and lift diagonally inwards Remove cover completely 6 Check impeller wheel and remove any foreign objects 7 Place cover in the original position and press down until it engages click 8 Install filters 9 Re insert baskets 25 en Fault what to do Fault table Fault Check water supply display lights up Error code 7 is lit Error code te is lit Error code Eid is lit Error code 24 is lit Error code 75 is lit Error code E 2 7 is lit 26 Cause Supply hose kinked Tap turned off Filter in the water supply blocked Intake opening on right inside of appliance covered by utensils Heating element calcified or soiled Filters are soiled or blocked Waste water hose kinked or blocked Siphon connection still sealed Cover on the waste water pump loose Waste water pump blocked or cover on the waste water pump is not locked in position Mains voltage too low Tap jammed or calcified Remedial action nstall supply hose without kinks Turn the tap on Turn the tap on Flow rate must be min 10 I min when water sup
43. tions for use or on the enclosed customer service list When calling please state the appliance number E Nr 1 and the production number FD 2 which can be found on the rating plate 32 on the appliance door Rely on the competence of the manufa cturer Contact us You can therefore be sure that the repair is carried out by trained service technicians who carry original spare parts for your domestic appliances 34 Installation and connection The dishwasher must be connected correctly otherwise it will not function properly The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions Install the appliance in the correct sequence 1 Checking appliance on delivery Installing the appliance Waste water connection Drinking water connection Electrical connection of ND Product package If you have any complaints contact the dealer where you purchased the appliance or our customer service m Dishwasher Instructions for use Installation instructions Warranty Installation materials Steam guard plate Rubber apron Power cord depending on model E EENEN ENE Safety instructions Please follow the safety instructions under Installation Delivery Your dishwasher has been checked thoroughly in the factory to
44. tive in or dried on food Intensive 70 Final rinse 65 utensils remnants containing Drying and cutlery starch or protein Auto a wi s optimised according all o the soiling with the aid Auto 45 65 of sensors auto oe ir J s optimised according e all o the soiling with the aid Auto 45 65 of sensors part dried common Prerinse ae aT Olean 50 all Intermediate rinse Eco 50 Final rinse 65 Drying IntensivZone Prerinse Express Wash j Yu Y Speed Perfect a a sensitive utensils le VarioSpeed Intermediate rinse N ur Slghty adhesive em Half load Finaline pp sensitive plastic fresh food remnants Extra drying Drying and glasses Uo Clean 45 m Io R Extra drying Intermediate rinse Quick 45 Final rinse 55 IN UN alltypes cold rinsing un IN iy ane Bretiise of utensils intermediate cleaning Prerinse Programme selection You can select a suitable programme according to the type of utensils and degree of soiling Information for test institutes Test institutes receive the information for comparability tests e g according to EN604386 These are the conditions for conducting the tests however these are not the results or consumption values Request by e mail to dishwasher test appliances com The product number E no and the production number FD are required which you can find on the rating plate on the appliance door G Additional options depending on model Additional optio
45. uid are adequate Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces Stainless steel appliances To prevent corrosion avoid using sponge cloths or wash them out thoroughly several times before using for the first time A Warning Health hazard Never use other domestic detergents e g containing chlorine Special salt and rinse aid Check the refill indicators and C5 If required refill salt and or rinse aid 23 en Cleaning and maintenance Filters The filters keep large foreign objects in the rinsing water away from the pump These foreign objects may occasionally block the filters The filter system consists of a coarse filter a flat fine filter and a microfilter 1 After each washing cycle check the filters for residue 2 Unscrew filter cylinder as illustrated and take out filter system 3 Remove any residue and clean filters under running water 4 Re install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system 24 Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms and 25 1 Check outlet nozzles on the spray arms for blockages 2 Unscrew the upper spray arms 1 4 revolution

Download Pdf Manuals

image

Related Search

Related Contents

Planet Technology VIP-110 User's Manual  Clique aqui para baixar o MANUAL DO ALUNO da FATEC Tatuí.  RISETTAGGIO: CURA E MANUTENZIONE: SPECIFICHE  Instrukcja montażu i obsługi Installation and Operating Instructions  Modulo di limite EZ-ZONE RM Manuale dell`utente  Ewent EW1604  Manual del usuario HeartSine samaritan® PAD SAM 300P  Dataflex ViewMate Style Monitor Arm 532  Oral-B PROFESSIONAL CARE 600  fiche technique a 890 insecticide pour insectes rampants  

Copyright © All rights reserved.
Failed to retrieve file