XC-540MT Setup Guide
Contents
1. CHECK Make sure the drain bottle is installed DRAIN BOTTLE Press 4 When this screen appears filling with ink is finished ROLL 44 7 Installing the Blade CAUTION Be sure to perform operations as specified by these instructions and never touch any area not specified in the instructions Sudden movement of the machine may cause injury CAUTION Never touch the tip of the blade with your fingers Doing so may result in injury and the cutting performance of the blade will be impaired L Insert a blade into the blade holder Insert the pin Insert the blade Insert the pin to the position where its end sticks out about 3 to 5 millimeters Pin A 4 Blade holder Blade Sf Insert the blade 2 Enter the blade replacement mode menu Press Guy SUB MENU gt Press C Y gt several times SUB MENU 1 Press C gt D MAINTENANCE gt Press AD k MAINTENANCE 1 Press C gt D REPLACE KNIFE d Press CID twice NOW PROCESSING Press Center The cutting carriage moves to a location permitting blade replace ment and then the screen shown in the figure appears OPEN FRONT COVER FINISHED Open the front cover Preparations are complete when this screen appears 45 7 Installing the Blade 3 Install the blade holder Loosen the screw shown in the figure Support the screw from below and insert the blade holder2. Repeat and to set the gateway address numbers When you ve finished making the setting press C Press Cmeu y Press lt gt to go back to the original screen 8 Network Settings Step 3 Make the Port Settings for the Software RIP Make the settings for the software RIP For the output destination use the setting for the IP address made on the machine For information about how to make the settings refer to the documentation for the software RIP You can check whether the connection to the network has been made by using the printing test feature in the software RIP you re using For information about how to carry out a printing test refer to the documenta tion for the software RIP 51 52 Roland 1000006544
3. If installed without supporting the screw in this way cutting quality may become poor TE TE thy Si Insert until the collar is Screw flush with the surface Support it from below Ed Tighten the screw Tug the blade holder upward to make sure it does not come loose aan Screw Close the front cover then press Center Important Note on the Handling and Use of the Cutting Carriage Se C G CA A Ya S Leave the cutting carriage screw loose when no blade holder is installed Keeping the screw tightened causes the blade holder insertion hole to become gradually smaller making installation difficult 46 8 Network Settings Introduction This machine has a built in print server as a network interface When you use the print server you can send output data to the machine from anywhere on the network TCP IP is used as the protocol Make sure the machine is connected to the network by an Ethernet cable The network settings on the machine must be made manually using the operation panel For information about how to make the settings refer to Step 2 Make the Network Settings on the Printer later in this chapter Also to perform output from the machine the software raster image processor RIP packed with the machine must be installed and set up on the computer you re using For information about installation and setup refer to the documentation for the softw
4. INKJET PRINTER MAINTENANCE GUIDE 2 Included Items Replacement blades for separating knife Replacement wipers Tweezers 21 3 Assembling and Installing Step 1 Assemble the Stand WARNING Perform this task with all power switches left switched off Otherwise sudden movement of the machine may cause injury CAUTION Unpacking and installation must be carried out by six or more persons Otherwise the machine or the stand may fall resulting in injury T Attach the stand legs to the stay Place the stay on the accessories box Stay Accessories box Attach the left and right stand legs to the stay Loosely tighten the locations shown in the figure Hexagonal wrench Stand leg left oe Stand leg right 22 Tighten the remaining bolts 3 Assembling and Installing Fully tighten all bolts to secure the stay and stand legs completely After assembling lock all casters and remove the accessories box a 4 places Le D ea T Lock Caster 2 Attach the rail slider and the arm Attach the arm to the rail slider Attach the arm retaining screw to the arm Arm retaining screw Rail slider Dn 4 places d w d Fe Orient this side toward the rear 23 3 Assembling and Installing Attach the rail slider to the stand legs Working on the right side first line up each tab with the slot in the rail slid
5. Metallic Silver Mode SET INK MODE WHITE INK H White Mode This completes selection of the ink mode Go on to Installing the Ink Cartridges Installing the Ink Cartridges Be sure to follow the on screen in structions for insertion and removal PET SOL CL LIQUID gah 67 A j Slot number 7 ep iil SA mL i a H o Insert in the direction shown in the figure o Insert and remove slowly one at a time P o Insert firmly as far as it will go During cleaning you insert and remove cartridges several times The on screen messages indicate which to insert and remove and when to insert and remove them Insert each color ink cartridge into the slot labeled with the matching color The cleaning cartridges are not differentiated by color 41 6 XC 540MT Installing the Ink Cartridges 42 L 4 PA Switch on the power and make the initial settings MENU O Hold down Crau D and press the sub power switch O MENU LANGUAGE Use DCI D to select the language you want ENGLISH a Press Ge LENGTH UNIT Use DCI D to select the unit of measurement you mm gt mm d want for length Press Center TEMP UNIT Use CR CT to select the unit of measurement you gt C d want for temperature Press Center Clean the print heads with the SOL INK cleaning cartridges SELECT INK TYPE Make sure the selected ink mode is enabled E SOL Max LcLm 4H White Metal
6. Settings for the Computer ss 46 Step 2 Make the Network Settings on the Printer ss 48 Step 3 Make the Port Settings for the Software RIP ses 50 Company names and product names are trademarks or registered trademarks of their respective holders Copyright 2009 Roland DG Corporation http www rolanddg com To Ensure Safe Use Improper handling or operation of this machine may result in injury or damage to property Points which must be observed to prevent such injury or damage are described as follows About WARNING and N CAUTION Notices Used for instructions intended to alert the user to the risk of death or severe N WARNING nee injury should the unit be used improperly Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly Note Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings as well to domestic animals or pets About the Symbols The symbol alerts the user to important instructions or warnings The specific meaning of the symbol is determined by the design contained within the triangle The symbol at left means danger of electrocution The symbol alerts the user to items that must never be carried out are forbidden The specific thing that must not be done is indicated by the design contained within the circle The symbol at left means the unit must ne
7. ink cartridges for the first time These are required only once when installing ink cartridges for the first time after shipment from the factory Firstly clean the print heads with the cleaning cartridges and then fill with the inks of each color This operation requires eight UNUSED SOL INK cleaning cartridges Never under any circumstances use anything other than the specified type of ink or cleaning fluid Installing the Ink Cartridges Be sure to follow the on screen instruc tions for insertion and removal SET SOL CL LIQUID o Insert in the direction shown in the figure o Insert and remove slowly one at a time o Insert firmly as far as it will go PA During cleaning you insert and remove cartridges several times The on screen messages indicate which to insert and remove and when to insert and remove them Insert each color ink cartridge into the slot labeled with the matching color The cleaning cartridges are not differentiated by color CAUTION Never insert your hand or fingers into the opening of the front cover The print heads move at high speed inside the cover Contact may cause injury 35 5 XC 540 Installing the Ink Cartridges I switch on the power and make the initial settings Close the front cover Front cover 2 Switch on the main power switch Main power switch MENU O Hold down
8. insufficient current may cause fire or electrical shock Never use out of doors or in any location where exposure to water or high humidity may occur Never touch with wet hands Doing so may result in fire or electrical shock Never allow any foreign object to get in side Never expose to liquid spills Inserting objects such as coins or matches or allowing beverages to be spilled into the ventilation ports may result in fire or electrical shock If anything gets inside immediately disconnect the power cord and contact your authorized Roland DG Corp dealer Never place any flammable object nearby Never use a combustible aerosol spray nearby Never use in any location where gases can accumulate Combustion or explosion may be a danger Handle the power cord plug and electri cal outlet correctly and with care Never use any article that is damaged Using a damaged article may result in fire or electrical shock When using an extension cord or power strip use one that adequately satisfies the machine s ratings for voltage frequency and current Use of multiple electrical loads on a single electrical outlet or of a lengthy extension cord may cause fire Connect to ground This can prevent fire or electrical shock due to current leakage in the event of malfunc tion Position so that the power plug is within immediate reach at
9. or may result in fire or the release of toxic gases A To Ensure Safe Use AN Warning Labels Warning labels are affixed to make areas of danger immediately clear The meanings of these labels are as follows Be sure to heed their warnings Also never remove the labels or allow them to become obscured Flammable Ink and discharged fluid are flam mable Keep away from open flame x Ink Is Toxic Ink and discharged fluid are toxic Avoid contact with the body Use only in a well ventilated area Caution Moving Print Heads The print heads inside the cover move at high speed and pose a hazard Never insert the hand or fingers into the gap Flammable Ink and discharged fluid are flammable Keep away from open flame Ink Is Toxic Ink and discharged fluid are toxic Avoid contact with the body Use only in a well ventilated area Caution High Temperature The platen and dryer become hot Ex ercise caution to avoid fire or burns Caution Pinching Hazard Be careful not to allow the fingers to become pinched when loading media or closing covers Caution High Temperature The platen and dryer become hot Exercise caution to avoid fire or burns AN Pour utiliser en toute s curit La manipulation ou l utilisation inad quates de cet appareil peuvent causer des blessures ou des dommages
10. utiliser en toute s curit PRUDENCE Attention outil de coupe Cet appareil contient un outil interne Pour viter les blessures manipuler l outil avec soin AN Risque de d charge ou de choc lectrique d lectrocution ou d incendie ATTENTION Brancher une prise lectrique conforme aux caract ristiques de cet appareil ten sion fr quence et courant Une tension incorrecte ou un courant insuf fisant peuvent causer un incendie ou un choc lectrique Caract ristiques I a TT mch LINHA o Kw lop 1 o g z 0 x Ne jamais utiliser l ext rieur ni un endroit ou l appareil risque d tre expos de l eau ou une humidit lev e Ne jamais toucher l appareil avec des mains mouill es Le non respect de cette consigne risque de provoquer un incendie ou un choc lec trique ATTENTION O Ne jamais ins rer d objet tranger dans l appareil Ne jamais exposer l appareil aux d versements de liquides L insertion d objets comme des pi ces de monnaie ou des allumettes ou le d verse ment de liquides dans les orifices de ventila tion peuvent causer un incendie ou un choc lectrique Si un objet ou du liquide s infiltre dans l appareil d brancher imm diatement le c ble d alimentation et communiquer avec le repr sentant Roland DG C
11. 60 kg 574 Ib or more Installation in an un suitable location may cause a major accident including tip over fall or collapse Unloading and emplacement are opera tions that must be performed by 6 persons or more Tasks that require undue effort when per formed by a small number of persons may result in physical injury Also if dropped such items may cause injury Be sure to lock the stand s casters If the machine should begin to topple a major accident may result including crushing of the appendages or the body When storing roll media implement ad equate safety measures to ensure that the stored media will not roll fall or topple over Danger exists of becoming pinned under the media and suffering serious injury Handling roll media is an operation that must be performed by two persons or more and care must be taken to prevent falls Attempting to lift heavy media in a manner that taxes your strength may cause physical injury AN Danger of fire burns or toxic gas emissions WARNING A D Caution high temperatures Areas such as the dryer become hot Exer cise caution to avoid fire or burns When printing is not being performed remove any loaded media or switch off the power The continued application of heat at a single location may cause the release of toxic gases from the media or pose a fire hazard Never use media that cannot withstand heat Doint so may degrade the media
12. CD and press the sub power switch ada C MENU LANGUAGE Use DCI D to select the language you want ENGLISH a Press Ge LENGTH UNIT Use C4 gt CY D to select the unit of measurement you mm gt mm d want for length Press Center TEMP UNIT Use C4 gt CY D to select the unit of measurement you C pC d want for temperature Press 36 5 XC 540 Installing the Ink Cartridges 2 Clean the print heads with the SOL INK cleaning cartridges SELECT INK TYPE Use CAD CT D to select the ink type E SOL Max LcLm e Press INSTALL Make sure the drain bottle is installed DRAIN BOTTLE amp Press Cater SET SOL CL LIQUID Insert cleaning cartridges into slots 2 3 8 and 9 23 89 FILLING INK gt gt REMOVE SOL CL Pull out the cleaning cartridges 23 89 Insert the cleaning cartridges YOU PULLED OUT into SET SOL CL LIQUID 1 67 12 FILLING INK slots 1 6 7 and 12 gt gt gt gt slots 4 5 10 and 11 O Pull out the cleaning cartridges 1 67 12 Insert the cleaning cartridges YOU PULLED OUT into SET SOL CL LIQUID 45 10 11 37 5 XC 540 Installing the Ink Cartridges REMOVE SOL CL Pull out the cleaning cartridges 45 10 11 qo 7 oe gt ceo FILLING INK PT gt gt gt gt gt gt gt gt D When this screen appears cleaning is finished DRAIN BOTTLE Make sure the drain bottle is installed an
13. NTION 10 S assurer de suivre les proc dures d utilisation d crites dans la documenta tion Ne jamais permettre quiconque ne conna t pas le fonctionnement ou la manutention de l appareil de le toucher L utilisation ou la manutention incorrectes peuvent causer un accident Garder les enfants loin de l appareil L appareil comporte des zones et des com posants qui pr sentent un danger pour les enfants et qui pourraient causer des bles sures la c cit la suffocation ou d autres accidents graves Ne jamais faire fonctionner l appareil apr s avoir consomm de l alcool ou des m dicaments ou dans un tat de fatigue L utilisation de l appareil exige un jugement sans faille L utilisation avec les facult s af faiblies pourrait entra ner un accident Ne jamais utiliser l appareil des fins autres que celles pour lesquelles il est con u Ne jamais l utiliser de mani re abusive ou d une mani re qui d passe sa capacit Le non respect de cette consigne peut causer des blessures ou un incendie Utiliser uniquement des accessoires d origine accessoires en option articles consommables c ble d alimentation et autres articles semblables compatibles avec l appareil Les articles incompatibles risquent de causer des accidents D brancher le cable d alimentation avant de proc der au nettoyage ou a l entretien de l appareil et avant d y fixer ou d en retirer des accessoires e
14. Roland SOL JE Trroim XC 540 XC 540MT Setup Guide Read this first This describes the setup tasks and important conditions about the installation location that must be met in order to enable use of this machine Roland DG Corporation Thank you very much for purchasing this product O To ensure correct and safe usage with a full understanding of this product s performance please be sure to read through this manual completely and store it in a safe location O Unauthorized copying or transferal of this manual in whole or in part is prohibited O The contents of this document and the specifications of this product are subject to change without notice O The documentation and the product have been prepared and tested as much as possible If you find any misprint or error please inform us O Roland DG Corp assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product regardless of any failure to perform on the part of this product O Roland DG Corp assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any article made using this product Contents A TO Ensure Safe USG ee ee REETA EE 2 AN Pourutiliser n TOUTE SECUIING sisusse oNN EEREN EEEN 9 STe CLIS A E E E ee A O E EE 17 1 Installation Environment 18 Deciding On an Installation Site nn 18 Temperature and Humidity sesesssessssesssesssseesseessses
15. all times This is to enable quick disconnection of the power plug in the event of an emergency Install the machine next to an electrical outlet Also provide enough empty space to allow immediate access to the electrical outlet If sparking smoke burning odor unusual sound or abnormal operation occurs im mediately unplug the power cord Never use if any component is damaged Continuing to use the machine may result in fire electrical shock or injury Contact your authorized Roland DG Corp dealer A To Ensure Safe Use AN Important notes about the power cord plug and electrical outlet Never place any object on top or subject to Never allow to get wet damage lt gt Zil Never bend or twist with undue force Never make hot Dust may cause fire Never bundle bind or roll up A To Ensure Safe Use AN Ink cleaning fluid and discharged fluid are flammable and toxic WARNING H D O In the event of ingestion or physical distress Keep open flame away from the work area Ink and discharged fluid are flammable Never store ink cleaning fluid or dis charged fluid in any of the following locations O Any location exposed to open flame O Any location where high temperature may occur O Near bleach or any other such oxidizing agent or explosive material O Any location within the reach of chil dren Fire may be a danger Accidental ingestion by children may po
16. are RIP Important The examples used in the procedures for making the settings described in this section assume you are using One computer and one machine The procedures and setting values described here may not be suitable for all operating environments If the computer you re using is connected to a number of networked devices or to the Internet incorrect settings may adversely affect the entire network For detailed information about the settings consult your network administrator Also the addresses used in this section are merely example settings Step 1 Make the Network Settings for the Computer The screen images used for explanation here are for Windows Vista Procedure Log on to Windows as a member of the Administrators group Display the Local Area Connection Status dialog box For Windows Vista From the Start menu click Control Panel Click Network and Internet then click Network and Sharing Center Click View status For Windows XP From the Start menu click Control Panel Click Network and Internet Connec tions then click Network Connections For Windows 2000 From the Start menu click Settings then click Network and Dial up Connec tions 47 8 Network Settings Click Properties If you re using Windows Vista and the User Account Control dialog box appears click Allow The Local Area Connection Properties dialog box appears Select Internet Proto
17. ay result in spinning without traction or other problems that impede media take up 26 3 Assembling and Installing Step 2 Mount the Machine WARNING Perform this task with all power switches left switched off Otherwise sudden movement of the machine may cause injury CAUTION Unpacking and installation must be carried out by six or more persons Otherwise the machine or the stand may fall resulting in injury Procedure Place the machine on the stand Main unit gt Bottom surface of the main unit Align with the fittings on the stand Secure the machine to the stand LEE LLUUMEUULIA o o 4 places 27 3 Assembling and Installing Step 3 Install the Drain Bottle WARNING Perform this task with all power switches left switched off Otherwise sudden movement of the machine may cause injury Procedure Remove the drain tube cover and attach the bottle stand Attach the drain tube cover to the underside of the machine for storage Remove the drain tube cover Secure the bottle stand in place Using the bolts that held the drain tube cover in place secure the bottle stand in place Drain tube cover Bottle stand 28 3 Assembling and Installing Remove the lid from the drain bottle Store the lid and inner cap for later use G Inner cap Drain bottle At the location shown in the fi
18. col Version 4 TCP IPv4 Windows Vista or Internet Protocol TCP IP NVIDIA nForce Networtang Cortroler Windows XP 2000 then click Properties Canigo If the check box for Internet Protocol is not selected then This conmection uses the folowing tems i e eae a click the check box to select it vi ces Packet Scheduler v Rie and Pnrter Shanng for Microsoft Networks M internet Protocol Version 6 TCP 1PvE CR mena Protocol Verson 4 v4 M Link Layer Topology Discovery Mapper L O Driver M Link Layer Topology Discovery Responder Transmission Control Protocol Intemet Protocol The default wide area network peotocol that provides communication across diverse interconnected networks Select Use the following IP address Enter the ce L information as shown below then click OK You can get IP set assigned automatically if network ts Pa DA ers yau need to ask yor ro Sat IP Address 192 168 0 XXX SRE TE Subnet Mask 255 255 255 0 Use the folowing P adress XXX may be any number you want from 1 to 254 How IP address 192 168 0 101 A oe ever be sure to specify a number that does not duplicate Default gateway nn a number used for another computer or device Here by way of example 192 168 0 101 is entered for the IP ad dress and 255 255 255 0 for the subnet mask Use the following DNS server addresses Preferred DNS server Alternate DNS server In
19. d press CENTER 3 Insert the ink cartridges for the respective colors Before you insert the ink cartridge for each color gently shake the cartridge SETSOLCRT Insert the ink cartridge for each color 1234567891011 12 FILLING INK gt gt gt gt gt gt gt gt gt gt Insert into the slot of the matching color CHECK Make sure the drain bottle is installed DRAIN BOTTLE Press 4 When this screen appears filling with ink is finished ROLL 38 6 XC 540MT Installing the Ink Cartridges For XC 540 refer to XC 540 Installing the Ink Cartridge on page 35 Ink Mode For XC 540MT the ink mode must be selected based on the types of ink to be used P 40 Selecting the Ink Mode OWhite Metallic Silver mode In addition to the respective ink cartridges of Cyan Magenta Yellow and Black each one of White and Metal lic Silver are used OWhite mode In addition to the respective ink cartridges of Cyan Magenta Yellow and Black two of White are used Metallic Silver ink cannot be used Filling with Ink for the First Time Special procedures are required when installing ink cartridges for the first time These are required only once when installing ink cartridges for the first time after shipment from the factory Firstly clean the print heads with the cleaning cartridges and then fill with the inks of each color This operation requires four UNUSED SOL INK cleaning cart
20. er imm diatement le c ble d alimentation Ne jamais utiliser si un composant est endommag Continuer utiliser l appareil peut causer un incendie un choc lectrique ou des bles sures Communiquer avec le repr sentant Roland DG Corp Autoris A Pour utiliser en toute s curit AN Remarques importantes propos du c ble d alimentation de la fiche et de la prise lectrique Ne jamais d poser aucun objet sur le c ble Ne jamais laisser l eau toucher le c ble la fiche sur la fiche ou sur la prise car cela risque de ou la prise les endommager NS J excessive Ne jamais tirer sur le c ble ou la fiche avec une La poussi re peut causer un incendie force excessive Ne jamais plier ni enrouler le c ble 13 A Pour utiliser en toute s curit AN L encre les liquides nettoyants et les liquides us es sont inflammables et toxiques ATTENTION O O 9S Ne pas approcher une flamme nue de l espace de travail L encre et les liquides us s sont inflam mables Ne jamais entreposer d encre de liquide de nettoyage ou des liquides us s dans les endroits suivants O un endroit expos une flamme nue O un endroit o il y a risque de temp ra ture lev e O pr s d eau de Javel d un autre agent d oxydation ou de mat riel explosif tout endroit la port e d enfants Il y a risque d incendie L ingestion acciden telle par un enfant peut pr
21. er and secure in place Head unit tool TT L a TS 8 Line up the tab with the slot 3 Attach the dancer roller Working from the right side first secure in place et 5 amp Ds Line up with the bolt hole Line up with the bolt hole and secure in place and secure in place 24 3 Assembling and Installing 4 Attach the shafts and engage the brake Fit the stoppers onto the shafts Fit two stoppers onto each shaft Orient so that this side faces outward OSL WHY Stopper TZ Tu A Stopper Place the shafts on the stand and engage the brake Peel off the tape Place the shafts on the stand is A EY lt x Engage the brake 25 3 Assembling and Installing 5 Attach the paper tube Pull the dancer roller back toward you Dancer roller Mount the paper tube and secure the arm in place First fit the paper tube securely onto the end cap on the same side as the right stand leg Next press the end cap on the same side as the arm into the paper tube and securely fit the end cap into the paper tube Finally secure the arm in place using the arm retaining screw pressing down from above oor OK OO Q 1m TR OF Le Fit onto this securely Tighten the screw while Ze U Pape For the paper tube use the included item Using something other than the included item m
22. gure secure in place the part you removed in step Fasten using the bolt provided which is attached to the underside of the machine Miles NII JA 02 o O ic Zo Gill Bottom surface of the main unit 29 3 Assembling and Installing Step 4 Attach the Ink cartridge Tray Procedure Loosen the upper bolts Remove the lower bolts Mount the ink cartridge tray on the upper bolts Hang on the upper bolts ey o call 7 7 hl aa o LL i E MW Paull e MULL A miil e PA pM 30 3 Assembling and Installing Step 5 Remove the Packing Materials Packing materials are attached to the machine to protect it from vibration during transportation When instal lation is complete remove them WARNING Perform this task with all power switches left switched off Otherwise sudden movement of the machine may cause injury O Remove all packing materials Any that remain may cause faulty operation or breakdown when the power is switched on O Store the packing materials carefully because they are needed again when transporting the machine for relocation or the like Packing material Peel off the tape Y Remove 31 3 Assembling and Installing You can attach the removed packing materials a
23. lic Silver Mode SELECT INK TYPE If an incorrect ink mode is enabled switch off the sub White Mode Again carry out the procedure on page 40 Selecting the Ink Mode If the selected ink mode is enabled press Center INSTALL Make sure the drain bottle is installed DRAIN BOTTLE 4 Press Canter SET SOL CL LIQUID Insert cleaning cartridges into slots 2 3 8 and 9 23 89 Tm ML gy P Y S d FILLING INK FL rOy 6 XC 540MT Installing the Ink Cartridges REMOVE SOL CL Pull out the cleaning cartridges 23 89 Insert the cleaning cartridges YOU PULLED OUT into slots 1 6 7 and 10 SET SOL CL LIQUID 1 67 10 FILLING INK 5 Pull out the cleaning cartridges 1 67 10 Insert TWO OF THE CLEANING CARTRIGES YOU PULLED OUT into slots 4 and 5 SET SOL CL LIQUID 45 FILLING INK gt gt gt gt gt gt REMOVE SOL CL 45 FILLING INK gt gt gt gt gt gt gt gt CHECK When this screen appears cleaning is finished DRAIN BOTTLE Make sure the drain bottle is installed and press Center 3 Insert the ink cartridges for the respective colors Before you insert the ink cartridge for each color gently shake the cartridge 43 6 XC 540MT Installing the Ink Cartridges SET SOL CRT Insert the ink cartridge for each color 12345678910 FILLING INK gt gt gt gt gt gt gt gt gt gt Insert into the slot of the matching color
24. mat riels Les pr cautions a prendre pour pr venir les blessures ou les dommages sont d crites ci dessous Avis sur les avertissements A ATTENTION Utilis pour avertir l utilisateur d un risque de d c s ou de blessure grave en cas de mauvaise utilisation de l appareil Utilis pour avertir l utilisateur d un risque de blessure ou de dommage mat riel en cas de mauvaise utilisation de l appareil Par dommage mat riel il est entendu dommage ou tout autre effet ind sirable sur la maison tous les meubles et m me les animaux domestiques A A propos des symboles Le symbole A attire l attention de l utilisateur sur les instructions importantes ou les avertissements Le sens pr cis du symbole est d termin par le dessin l int rieur du triangle Le symbole gauche signifie danger d lectrocution Le symbole avertit l utilisateur de ce qu il ne doit pas faire ce qui est interdit La chose sp cifique ne pas faire est indiqu e par le dessin l int rieur du cercle Le symbole gauche signifie que l appareil ne doit jamais tre d mont Le symbole B pr vient l utilisateur sur ce qu il doit faire La chose sp cifique faire est indiqu e par le dessin l int rieur du cercle Le symbole gauche signifie que le fil lectrique doit tre d branch de la prise AS Pour utiliser en toute s curit AN L utilisation incorrecte peut causer des blessures ATTENTION N ATTE
25. n option Tenter ces op rations pendant que l appareil est branch une source d alimentation peut causer des blessures ou un choc lectrique Ne jamais tenter de d monter de r parer ou de modifier l appareil Le non respect de cette consigne risque de provoquer un incendie un choc lectrique ou des blessures Confier les r parations un technicien ayant la formation requise PRUDENCE A 9 Faire preuve de prudence pour viter l crasement ou le coincement La main ou les doigts peuvent tre cras s ou coinc s s ils entrent en contact avec certaines surfaces par inadvertance Faire preuve de prudence pendant l utilisation de l appareil Ne jamais faire fonctionner l appareil si on porte une cravate un collier ou des v tements amples Bien attacher les ch eveux longs Ces v tements ou ces objets peuvent tre coinc s dans l appareil ce qui causerait des blessures Utiliser l appareil dans un endroit propre et bien clair Travailler dans un endroit sombre ou en combr peut causer un accident l utilisateur risque par exemple de tr bucher malencon treusement et d tre coinc par une partie de l appareil PRUDENCE Ne jamais grimper ni s appuyer sur la S machine La machine n est pas con ue pour sup porter le poids d une personne Grimper ou s appuyer sur la machine peut d placer des l ments et causer un faux pas ou une chute ce qui causerait des blessures A Pour
26. ng such operations while the ma chine is connected to a power source may result in injury or electrical shock Never attempt to disassemble repair or modify the machine Doing so may result in fire electrical shock or injury Entrust repairs to a trained service technician CAUTION A gt O Exercise caution to avoid being pinched or becoming caught Inadvertent contact with certain areas may cause the hand or fingers to be pinched or become caught Use care when performing operations Never attempt operation while wearing a necktie necklace or loose clothing Bind long hair securely Such items may become caught in the ma chine resulting in injury Conduct operations in a clean brightly lit location Working in a location that is dark or cluttered may lead to an accident such as becoming caught in the machine as the result of an inadvertent stumble Never climb or lean on the machine The machine is not made to support a per son Climbing or leaning on the machine may dislodge components and cause a slip or fall resulting in injury Caution cutting tool This machine has an internal tool To avoid injury handle the tool with care A To Ensure Safe Use AN Danger of electrical short shock electrocution or fire WARNING WARNING Connect to an electrical outlet that com plies with this machine s ratings for volt age frequency and current Incorrect voltage or
27. orp autoris Ne jamais placer d objet inflammable proximit de l appareil Ne jamais util iser de produit inflammable en a rosol proximit de l appareil Ne jamais utiliser l appareil dans un endroit o des gaz peuvent s accumuler Une combustion ou une explosion pourraient se produire 11 A Pour utiliser en toute s curit N ATTENTION 12 Manipuler le c ble d alimentation la fiche et la prise lectrique correctement et avec soin Ne jamais utiliser un article endommag car cela pourrait causer un incendie ou un choc lectrique Si une rallonge ou une bande d alimentation lectrique sont utilis es s assurer qu elles correspondent aux caract ristiques de l appareil tension fr quence et courant L utilisation de plusieurs charges lectriques sur une prise unique ou une longue rallonge peut causer un incendie Mise la terre La mise la terre peut pr venir un incendie ou un choc lectrique dus une fuite de courant en cas de d faillance Placer l appareil de fa on ce que la fiche soit facile d acc s en tout temps Ainsi l appareil pourra tre d branch rapi dement en cas d urgence Installer l appareil pr s d une prise lectrique En outre pr voir suffisamment d espace pour que la prise lectrique soit facile d acc s S il se produit des tincelles de la fum e une odeur de br l un bruit inhabituel ou un fonctionnement anormal d branch
28. que d incendie de br lures ou d missions de gaz toxiq ATTENTION A Attention temp ratures lev es Les zones comme le s choir chauffent Faire preuve de prudence pour viter un incendie ou des br lures Quand aucun travail d impression n est en cours retirer tout support de l appareil ou couper l alimentation lectrique L application continue de chaleur un point unique peut causer l mission de gaz tox iques ou cr er un risque d incendie A ATTENTION 9S Ne jamais utiliser un support qui ne peut pas supporter la chaleur L utilisation d un support qui ne supporte pas la chaleur peut d t riorer le support cr er un risque d incendie ou causer l mission de gaz toxiques 15 A Pour utiliser en toute s curit AN Vignettes d avertissement Des vignettes d avertissement sont appos es pour qu il soit facile de rep rer les zones dangere uses La signification des vignettes est donn e ci dessous Respecter les avertissements Ne jamais retirer les vignettes et ne pas les laisser s encrasser x 16 Inflammable L encre et les liquides us s sont in flammables Les garder loin de toute flamme nue L encre est toxique L encre et les liquides us s sont toxiques Eviter tout contact avec le corps Utiliser uniquement dans un endroit bien a r Attention T tes d impres
29. ridges Never under any circumstances use anything other than the specified type of ink or cleaning fluid Applying the Labels White Mode Only In selecting the White mode affix the cartridge slot labels on the locations shown in the figure below Back of the printer 39 6 XC 540MT Installing the Ink Cartridges Selecting the Ink Mode Be sure to make the selection of the ink mode when switching on the power for the first time CD IMPORTANT Selection of the ink mode can be made only once when installing ink cartridges for the first time after the unit has shipped from the factory Once ink filling has been started the ink mode cannot be changed Select it with care Procedure Close the front cover lf the main power switch is on then switch it off White Metallic Silver Mode Hold down C gt D and Cx switch on the main power switch White Mode Hold down C4 and Cx switch on the main power switch When a message appears on the display screen release the operation panel buttons Main power switch Display screen Press at the same time hra puse gt Press at BASEPOINT SHEET CUT TEST CUT E pose CUT the same time White Metallic Silver Mode White Mode 40 6 XC 540MT Installing the Ink Cartridges SET INK MODE When this screen appears press WH MT INK d The sub power switches off automatically White
30. rk Settings SUBNET MASK 255 000 000 000 H SUBNET MASK 255 000 000 000 H SUBNET MASK 255 255 255 000 H K SETUP SHEET 4 gt ROLL Use C 4 D CYO to select the address number SUBNET MASK 255 255 255 000 Note For the subnet mask make the setting the same value as the one used by the computer Here 255 255 255 000 is entered by way of example Press C gt gt Repeat and to set the subnet mask When you ve finished making the setting press CENTER Press Cvenu Press lt gt to go back to the original screen If you re using one computer and one machine this completes the settings to make on the printer Go on to Step 3 If setting the gateway address is required then go on to the procedure following this one 3 Set the gateway address NETWORK GATEWAY ADDR gt GATEWAYADDR 4 000 000 000 000 e GATEWAY ADDR 44 gt 255 000 000 000 e GATEWAYADDR 44 gt 255 255 000 000 e GATEWAYADDR 44 gt 255 255 255 255 e K SETUP SHEET 4 gt ROLL 50 From the screen displayed in press CY gt twice Press C gt gt twice Use C 4 gt CY to select the address number GATEWAY ADDR 255 255 255 255 Note For information about the value to enter for the gateway ad dress consult your network administrator Here 255 255 255 255 is entered by way of example Press C gt gt
31. romagnetic energy 1 Installation Environment Temperature and Humidity Maintain the specified temperature and humidity even when the machine is not in use Temperatures that are too high may degrade the ink and cause malfunction Temperatures that are too low may cause the ink to freeze and damage the heads During operation Temperature 20 to 32 C 68 to 90 F relative humidity 35 to 80 no condensa tion During non operation Temperature 5 to 40 C 41 to 104 F relative humidity 20 to 80 no condensa tion Installation Space The space shown in the figure is required in order to use this machine 3 700 mm 145 7 in 2 700 mm 106 3 in 1 200 mm 47 3 in 2 500 mm 98 5 in Unit space Work space 19 Chapter 2 Getting Ready 2 Included Items The following items are included with the machine Make sure they are all present and accounted for Dancer roller Stand leg left Stand leg right Rail slider Paper tube Shafts Arm Arm retaining Screw Drain bottle SOL INK cleaning cartridges Drain bottle stand Media clamps The media clamps are installed on the machine 20 VGSV BYS SISSS Washers Hexagonal wrench Setup guide this document Cleaning fluid Head unit tool SPECIAL COLOR INK GUIDE XC 540MT only Cleaning stick Cleaning kit r Blade holder Pin Software RIP Cartridge slot label XC 540MT only
32. se a health hazard Never place an ink cartridge in fire Ink may flow out catch fire and spread fire to other nearby objects Never drink or sniff ink cleaning fluid or discharged fluid or allow them to come in contact with the eyes or skin Doing so may be hazardous to the health CAUTION Ensure adequate ventilation for the work area Failing to perform ventilation may result in a health hazard or danger of combustion due to ink fumes Never allow an ink cartridge to be sub jected to impact and never attempt to disassemble Ink may leak O In the event of contact with the eyes immediately flush with water for at least 15 minutes If eye ir ritation continues seek treatment by a physician O In the event of contact with skin immediately wash with soap If irritation or inflammation occurs seek treatment by a physician O In the event of ingestion do not induce vomiting and immediately seek treatment by a physician Forcibly inducing vomiting may lead to danger of choking O If odor leads to physical distress move to a well ventilated location and rest quietly If dizziness or nausea persists seek treatment by a physician A To Ensure Safe Use This machine weighs 260 kg 574 Ib Media weighs 30 kg 67 Ib WARNING WARNING Install the machine in a location that is level stable and able to bear the weight of the machine The total weight of the machine may reach 2
33. senter un risque pour la sant Ne jamais incin rer une cartouche d encre De l encre pourrait couler s enflammer et le feu se r pandre des objets proches Ne jamais boire l encre le liquide de net toyage ni les liquides us s ne pas en respirer les vapeurs et ne pas laisser les produits entrer en contact avec les yeux ou la peau Cela est dangereux pour la sant PRUDENCE O En cas d ingestion ou de trouble physique S assurer que le lieu de travail est bien a r L absence d a ration ad quate peut cr er une situation dangereuse pour la sant ou un risque de combustion cause des vapeurs qui emanent de l encre Ne jamais soumettre une cartouche d encre des chocs Ne jamais tenter d ouvrir une cartouche d encre De l encre pourrait s chapper O En cas de contact avec les yeux rincer imm diatement et abondamment a l eau courante pendant au moins 15 minutes Si les yeux sont toujours irrit s consulter un m decin O En cas de contact avec la peau laver imm diatement l eau et au savon En cas d irritation ou d inflammation de la peau consulter un m decin En cas d ingestion ne pas provoquer le vomissement et demander imm diatement l aide d un m decin Provoquer le vomissement peut cr er un risque de suffocation O Si l odeur cause un trouble physique amener la personne dans un endroit bien a r et la faire se reposer Si l tourdissement ou la naus e per
34. sion mobiles Les t tes d impression sous le couvercle se d placent haute vitesse et repr sen tent un danger Ne jamais ins rer la main ou les doigts dans l ouverture L encre est toxique L encre et les liquides us s sont toxiques Eviter tout contact avec le corps Utiliser uniquement dans un endroit bien a r Inflammable L encre et les liquides us s sont inflamma bles Les garder loin de toute flamme nue Attention Temp rature el v e La platine et la surface de s chage chauffent Etre prudent pour viter un incendie ou des br lures Attention Risque de pincement Faire attention de ne pas coincer les doi gts pendant le chargement du support ou lors de la fermeture du couvercle Attention Temp rature el v e La platine et la surface de s chage chauffent Etre prudent pour viter un incendie ou des br lures Setup Guide 1 Installation Environment 18 Deciding On an Installation Site Install in a quiet stable location offering good operating conditions An unsuitable location can cause accident fire faulty operation or breakdown WARNING WARNING WARNING WARNING WARNING CAUTION Install the machine in a location that is level stable and able to bear the weight of the machine The total weight of the machine may reach 260 kg 574 Ib or more Installa tion in an unsuitable location may cause a major accident including tipo
35. sistent consulter un m decin 14 A Pour utiliser en toute s curit AN Le poids de cet appareil est de 260 kg 574 Ib Le poids du support est de 30 kg 67 Ib ATTENTION Installer l appareil un endroit stable et plat et capable de supporter son poids Le poids total de l appareil peut tre d au moins 260 kg 574 Ib Installer l appareil un endroit inappropri peut provoquer un accident grave comme le renversement la chute ou l crasement Le dechargement et la mise en place doivent tre faits par au moins six per sonnes Les taches qui exigent un effort trop grand si elles sont ex cut es par un petit nombre de personnes peuvent tre cause de blessures La chute d articles tr s lourds peut aussi causer des blessures ATTENTION S assurer de verrouiller les roulettes de la base Si l appareil devait commencer basculer il s ensuivrait un accident grave par exemple l crasement de membres ou du corps Prendre les mesures de s curit ad quates pour l entreposage des rouleaux de support pour s assurer qu ils ne rouleront pas ne tomberont pas et ne se renverseront pas Il y a risque d tre cras par le support et de subir des blessures graves La manutention du support en rouleau doit tre faite par deux personnes ou plus et il faut prendre des pr cautions pour viter les chutes Tenter de soulever des objets trop lourds peut causer des blessures AN Ris
36. sseesseesseeossseosseonseessseesseesseessseesseessseesseeessess 19 ISAAC SPACE sssini a dt E Eit 19 2 MNCS OO a Raa SEE n EN 20 3 Assembling and INSTANAOL an aan 21 Step 1 Assemble the Stand sn 21 Step 2 Mount the Machine sscsisssssosserstonstscosstaedventiocsasesbindassntneasdsiasuneivopeansdit aansbalenieestassbanebeaveens 26 Step 3 Install the Drain Bottle shine 27 Step 4 Attach the Ink cartridge Tray nn 29 Step 5 Remove the Packing Materials nn 30 4 Connecting the Cables entorse 32 Connecting the Cable of the Take up Unit ss 32 Connecting the Power Cable and the Network Cable ss 33 5 XC 540 Installing the Ink Cartridges cccceccccseeeeeeeeeeeeeeeeeeaeeeeeaeeees 34 Filling with Ink for the First TiMeE ses essssesssseessseessseesssseesssseesnssesnsseessseeosseesoseeoosseeosssersssseesss 34 Installing the Ink Cartridges annees 34 6 XC 540MT Installing the Ink Cartridges cccccccccseeeeeeeeeeeeaeeeeeaeeees 38 E MOC ogien cece EEAS EEEE O AEE EEEE AEE 38 Filling with Ink for the First TIME 38 Applying the Labels White Mode Only 38 Selecting the Ink Mode rennes 39 Installing the Ink Cartridges sseessseessessseessseesseessseesseesseesnseessseesseosseeosseesseesuseosseesseessseessseessess 40 7 Installing the Blade diese deci latente ete apn eee 44 8 Network Settings names enntes dense cdd en ente Donc 46 OO tere yr eee nett a ieee e renee Ce T 46 Step 1 Make the Network
37. t the location shown in the figure for storage g HIII LME ML AUIII 2r O1 Packing material Align with the two tabs and secure in place 32 4 Connecting the Cables Connecting the Cable of the Take up Unit Peel off the tape Pass the take up unit cable through at the locations shown in the figure and con nect it Cable clamp Take up unit cable Take up unit 33 4 Connecting the Cables Connecting the Power Cable and the Network Cable WARNING Connect to electrical outlet that complies with this machine s ratings for voltage frequency and current Incorrect voltage or insufficient current may cause fire or electrical shock WARNING Connect to ground This can prevent fire or electrical shock due to current leakage in the event of malfunction WARNING Perform this task with all power switches left switched off Otherwise sudden movement of the machine may cause injury Electrical outlet dy Ethernet 100Base TX recommended aA p Power cord o I TT G TS e o amp HN o Pass the cables through here 34 5 XC 540 Installing the Ink Cartridges For XC 540MT refer to XC 540MT Installing the Ink Cartridge on page 39 Filling with Ink for the First Time Special procedures are required when installing
38. the Local Area Connection Properties dialog box click OK then in the Local Area Connection Status dialog box click Close 48 8 Network Settings Step 2 Make the Network Settings on the Printer Important The addresses used in this section are merely example settings For detailed information about the settings consult your network administrator L Set the IP address MENU Press Cue SYSTEM INFO gt Press C Y D several times SYSTEM INFO Press C gt gt NETWORK gt Press AD P ADDRESS TI Press C gt gt three times 000 000 000 000 e IP ADDRESS 192 168 000 XXX Note Here XXX may be any number you want from 2 to 254 How ever be sure to specify a number that does not duplicate the setting you made in Step 1 Here 192 168 000 003 is entered by way of example Make the portion that corresponds to 192 168 000 the same as the setting on the computer IP ADDRESS Use Ca gt gt to select the address number 192 000 000 000 d P ADDRESS Press C gt gt 192 000 000 000 d P ADDRESS Repeat and to set all the address numbers 192 168 000 003 d When you ve finished making the setting press C NETWORK Press C lt IP ADDRESS gt The screen shown in the figure appears 2 Set the subnet mask NETWORK Press CV gt SUBNET MASK gt SUBNET MASK TI Press C gt D twice 000 000 000 000 H 49 8 Netwo
39. ver fall or collapse Never install out of doors or in any location where exposure to water or high humidity may occur Current leakage may cause electrical shock electrocution or combustion and fire Never install close to any flammable object or in a gas filled location Combustion or explosion may be a danger Install in a clean brightly lit location Conduct operations in a clean brightly lit location Working in a location that is dark or cluttered may lead to an accident such as becoming caught in the machine as the result of an inadvertent stumble Position so that the power plug is within immediate reach at all times This is to enable quick disconnection of the power plug in the event of an emer gency Install the machine next to an electrical outlet Also provide enough empty space to allow immediate access to the electrical outlet Ensure adequate ventilation for the work area Failing to perform ventilation may result in a health hazard or danger of com bustion due to ink fumes Unsuitable Installation Sites O Locations subject to large fluctuations in temperature or humidity O Locations subject to shaking or vibration O Locations where the floor is tilted not level or unstable O Dusty locations O Locations exposed to direct sunlight or near air conditioning or heating equipment O Locations exposed to water or moving air O Locations exposed to considerable electrical or magnetic noise or other forms of elect
40. ver be disassembled The symbol alerts the user to things that must be carried out The specific thing that must be done is indicated by the design contained within the circle The symbol at left means the power cord plug must be unplugged from the outlet A To Ensure Safe Use AN Incorrect operation may cause injury WARNING gt D O O 6 6 WARNING Be sure to follow the operation proce dures described in this documentation Never allow anyone unfamiliar with the usage or handling of the machine to touch it Incorrect usage or handling may lead to an accident Keep children away from the machine The machine includes areas and compo nents that pose a hazard to children and may result in injury blindness choking or other serious accident Never operate the machine while tired or after ingesting alcohol or any medica tion Operation requires unimpaired judgment Im paired judgment may result in an accident Never use the machine for any purpose for which it is not intended or use the machine in an undue manner that exceeds its capacity Doing so may result in injury or fire For accessories optional and consum able items power cord and the like use only genuine articles compatible with this machine Incompatible items may lead to an acci dent Before attempting cleaning maintenance or attachment or detachment of optional items disconnect the power cord Attempti
Download Pdf Manuals
Related Search