Home

manual

1. uincat Installation Operating and Servicing Instructions Opus 700 Electric Salamander Grill OE7304 Please make a note of your product details for future use Date Purchased Model Number Serial Number Dealer OPUS 700 IS 318 ECN 3607 Page 1 of 12 CONTENTS Important Information Warnings and Precautions Technical Data Checklist of Enclosures Installation and Commissioning Operating Instructions Cleaning servicing Maintenance and Component Replacement Fault Finding Spare Parts List Accessories service Information and Guarantee CO OC MWWMDWOONDURWW W PY A I h NO IMPORTANT INFORMATION Read these instructions carefully before using this product paying particular attention to all sections that carry warning symbols caution symbols and notices Ensure that these are understood at all times WARNING This symbol is used whenever there is a risk of personal injury NOTE This symbol is used to provide additional information hints and tips CAUTION This symbol is used whenever there is a risk of damaging your Lincat product KEEP THIS MANUAL FOR FUTURE REFERENCE IS 318 ECN 3607 Page 2 of 12 WARNINGS AND PRECAUTIONS in accordance with national and local regulations in force in the country of This appliance must be installed commissioned and serviced by a qualified person installation lf the supply cord is damaged it must be replaced by the
2. ailing rate IS 318 ECN 3607 Page 12 of 12
3. in reverse order Energy regulator Remove hood Remove knob from energy regulator IS 318 ECN 3607 Page 7 of 12 Remove 2 screws in the control panel to release the energy regulator The control panel may be removed if required by releasing the screw at the rear of the panel and drawing sideways at the back Transfer the cables to the new regulator and reassemble by reversing the above procedure Relay Remove hood and control panel see energy regulator Remove relay from mounting plate transfer the cables to the new relay and reassemble by reversing the above procedure FAULT FINDING Please refer to the Service Help Desk number on the final page of this manual SPARE PARTS LIST ISC Handle disc metal Control knob Relay o O SA165 Enamelled grill pan SH13 Grill shelf ACCESSORIES Part Number Floor stand OA7908 CSB A7907 A7908 IS 318 ECN 3607 Page 8 of 12 OA7909 Floor stand Position floor stand and level on adjustable feet Adjust height of stabilising brackets Fig 4 A Mark and drill floor for stabilising brackets B Fix into position Position Salamander on top of floor stand lining up holes in frame with pierce nuts in appliance base Fix appliance to stand using 4 M8 x 50mm screws Fig 4 OA7908 Bench stand screw M8 x 16mm screws into front 2 pierce nuts in the base of the appliance Attach mounting brackets to the rear of the base of the applia
4. istant sheathed flexible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord code 60245 IEC 57 Connection to the electrical supply is at the rear of the appliance Unclip the protective cover and fit a suitable cable into the strain relief and the inlet terminal block The block is suitable for 16mm lt solid single core cable or 2 sizes lower of stranded cable i e 10 and 6mm The appliance is supplied for connection to a single phase supply OPERATING INSTRUCTIONS Only qualified or trained personnel should use this appliance Turn on the power supply the green power on neon will illuminate Rotate the control knob to the desired setting To shutdown rotate the control knob to the Off position and switch off at the isolating switch Cooking on the Salamander Fig 2 To mount the branding plate A on the grill shelf C locate the holes to the rear of the branding plate over the pegs on the rear of the grill shelf Similarly the drip tray B mounts on the pegs at the front of the grill shelf Shelf supports within the cooking cavity allow a variety of height levels and angles to optimise the cooking process An enamelled grill pan sits in the base of the cooking cavity This must always be in place when the grill is in operation Toasting Use the grill shelf in the horizontal position for toasting or browning cheese melting Grilling The branding plate is ideal for cooking steaks fille
5. lease tell us Brief details of the problem Product code Type number All available on serial plate Serial number Lincat reserve the right to carry out any work under warranty given reasonable access to the appliance during normal working hours Monday to Friday 08 30 to 17 00 GUARANTEE This unit carries a comprehensive UK mainland 2 year warranty The guarantee is in addition to and does not diminish your statutory or legal rights The guarantee does not cover e Accidental damage misuse or use not in accordance with the manufacturer s instructions e Consumable items such as filters glass bulbs slot toaster elements and door seals e Damage due to incorrect installation modification unauthorised service work or damage due to scale food debris build up etc The manufacturer disclaims any liability for incidental or consequential damages Attendance is based on reasonable access to the appliance to allow the authorised technician to carry out the warranty work Service calls to equipment under warranty will be carried out in accordance with the conditions of sale Unless otherwise specified a maximum of 15 minutes of administrative time not spent directly carrying out servicing work is provided for within the warranty Any requirement for staff attending the call to spend greater time than 15 minutes due to administrative requirements such as on health and safety risk assessments will be chargeable at the prev
6. manufacturer its service agent or similarly qualified person Ensure that the plug socket is accessible at all times Strip plastic coating and clean the appliance before use During operation parts may become hot avoid accidental contact Disconnect this appliance before servicing maintenance or cleaning TECHNICAL DATA E804 ight kg Weight Power rating Kw Be 55 Supply 1N E Current A CHECK LIST OF ENCLOSURES Warranty card Instructions manual Branding plate Grill shelf Grill pan IS 318 ECN 3607 Page 3 of 12 INSTALLATION AND COMMISSIONING This appliance must be earthed _ An equipotential bonding terminal is provided to allow cross bonding with other equipment lf replacing the plug connect the terminals as follows Green and Yellow wire Earth E Blue wire Neutral N Brown wire Live L Install this appliance on a level surface ensuring all vents are unobstructed Install this appliance on a level surface ensuring all vents are unobstructed Any partitions walls or furniture must be of non combustible material Minimum distances A 100mm B 1000mm see Fig 1 Fig 1 IS 318 ECN 3607 Page 4 of 12 Means of isolation with at least 3mm contact separation in all poles must be incorporated into the fixed wiring of this appliance The fixed wiring insulation must be protected by insulated sleeving having a temperature rating of at least 60 Deg C Supply cords shall be oil res
7. nce using 2 No 6 self tapping screws Fit appliance onto bench stand locating screw heads in the keyhole slots Fig 5 A IS 318 ECN 3607 Page 9 of 12 Slide the appliance back until the mounting brackets hit the back face of the stand arms Secure the brackets fixing through the hole in the back face using 2 No 6 self tapping screws Drill mounting surface hole diameter 5 0mm to dimensions shown in Fig 5 and fix into position using 4 M4 x 20mm screws into rivenuts in the underside of the stand feet Fig 5 OA7909 Wall shelf Fig 6 Ensure wall construction is substantial enough to support the weight of the Salamander grill Mark and drill wall for M10 Rawl bolts B Fix shelf to wall Position Salamander on top of wall shelf lining up the mounting holes A in the top of the shelf with the pierce nuts in the base of the appliance IS 318 ECN 3607 Page 10 of 12 Fix in position using 4 M8 x 16mm screws Fig 6 IS 318 ECN 3607 Page 11 of 12 SERVICE INFORMATION For help with the installation maintenance and use of your Lincat equipment please contact our service department UK 01522 875520 For non UK customers please contact your local Lincat dealer All service work other than routine cleaning should be carried out by one of our authorised service agents We cannot accept responsibility for work carried out by other persons To ensure your service enquiry is handled as efficiently as possible p
8. ts chops cutlets etc To achieve best results pre heat for 10 minutes before product is introduced IS 318 ECN 3607 Page 5 of 12 IS 318 CLEANING Do not use a water jet or steam cleaner and do not immerse this appliance Clean all panels with warm water and mild detergent do not use abrasive materials Dry with a soft cloth stubborn deposits on the branding plate can be removed by use of a cleaner such as Carbon Off available from Lincat Regularly empty and clean the drip tray SERVICING MAINTENANCE AND COMPONENT REPLACEMENT All servicing maintenance and component replacement on this appliance should be carried out by one of our recommended service engineers ECN 3607 Page 6 of 12 Access to components requires removal of the hood Remove the 2 screws on the underside of the front of the hood Fig 3 A This will release the 2 retaining clips which can be removed by pulling them into the cavity Hinge back the hood to clear the inner flue and slide 10mm to the right to enable it to be lifted clear Replace after servicing by reversing the procedure Figure shows top raised for clarity will not rise until clips are undone Fig 3 Element Remove hood and disconnect cables to element Remove the 3 element mounting plate screws and remove the element from inside grill by sliding out the mounting plate from the side Remove the defective element by unscrewing from the mounting plate Replace

manual

Contents

Download Pdf Manuals

Related Search

Related Contents