V190SG2e BK
Contents
1. Installation The surface on which the appliance is to be placed must be level Do not use a frame or similar The appliance can be installed as a free standing unit against a wall built into a kitchen element or lined up with other ap pliances figs 2 3 600 600 fig 2 The appliance viewed from above If the appliance is placed beside a wall there must be sufficient room for its door to be opened wide enough to allow the shelves to be pulled out fig 4 fig 3 fig 4 Ventilation It is important that the appliance be well p ventilated and that air can circulate unhin dered above below and around it The figures below illustrate how the neces I sary air circulation around the appliance 1005 es can be ensured figs 5 100 min 30 min 30 fig 5 The distance pieces on the rear of the ap pliance ensure sufficient air circulation Fit the two caps supplied with the appliance as shown in fig 7 Setting up It is important that the appliance be abso lutely level It can be levelled by screwing the adjustable feet at the front of the appli ance up or down fig 8 PN S Use a spirit level to check that the appliance2. op og ned knapperne Temperaturen kan reguleres fra 5 til 22 C dog s ledes at temperaturen ikke kan stilles varmere end den aktuelle setpunkt for den verste temperaturf ler Alarmer Der er en underalarm for den kolde tempe raturf ler og en overalarm for den varme temperaturf ler Alarmen best r dels af en beeper og af en advarsel p displayet Alarm for h j temperatur beep lyd display skift mellem HtA og aktuel temperatur Alarm for lav temperatur beep lyd display skift mellem LtA og aktuel temperatur Alarmtemperaturen afh nger af setpunk terne Beep lyden kan annulleres ved et tryk p en tilf ldig termostatknap For at fjerne display alarmen skal on off knappen trykkes ind F rst for slukke alarmen Derefter igen for genopstart af kompressor D ralarm N r d ren har v ret bnet mere end 2 minutter aktiveres d ralarmen Lyset For at slukke lyset trykkes n gang p x 17 Permanent belysning For preesentation af Deres vin kan De v lge at have lyset t ndt permanent ved at trykke pa lyssymbolet 3 to gange For at slukke for lyset trykkes igen pa X Fler zone indstilling for serverings temperering Typisk indstilling for denne anvendelse er en top bund indstilling pa 16 6 Med denne indstilling vil temperaturerne fordele sig ned igennem skabet til opbevaring af forskellige vintyper efter f lgende fordeling fra top mod bund e tunge r dvine 16 til
3. V190SG2e BK GB Instructions for use DK Brugsanvisning Warning In case this appliance contains hydrocar bon refrigerant please refer to guidelines listed below As the appliance contains a flammable refrigerant it is essential to ensure that the refrigerant pipes are not damaged Standard EN378 specifies that the room in which you install your appliance must have a volume of 1m per 8 g of hydrocarbon refrigerant used in the appliances This is to avoid the formation of flammable gas air mixtures in the room where the appli ance is located in the event of a leak in the refrigerant circuit The quantity of the refrig erant used in your appliance is indicated on the rating plate WARNING Keep ventilation openings in the appliance s cabinet or in the built in structure clear of obstruction WARNING Do not use other mechanical devices or other means to ac celerate the defrosting process than those recommended by the manufacturer WARNING Do not damage the refrigerant system WARNING Do not use electrical appli ances inside the refrigerated storage compartment unless they are of a type recommend ed by the manufacturer WARNING Do not expose the appliance to rain WARNING This appliance is not intended for use by young children or infirm persons unless they have been adequately super vised by a responsible person to ensure that they can use the appliance safely Young children should be superv
4. C skal apparatet st op i minimum en time inden ibrugtag ning Ibrugtagning og installation Placering Af sikkerhedsm ssige og driftsm ssige grunde m apparatet ikke placeres uden d rs Stil skabet p et plant underlag i et t rt og godt ventileret rum max 75 relativ luftfugtighed Anbring ikke skabet t t p varmekilder s som komfur eller radiator og undg at det uds ttes for direkte sollys el ler varme fra anden varmkilde Omgivende temperatur Klimaklassen st r p typeskiltet se side 3 og 12 Den angiver indenfor hvilke omgivende temperaturer k lekabet k rer optimalt Vinskabene med vinterposition fungerer dog ned til 5 C Klimaklasse Tilladt rumtemperatur SN 10 C til 32 C N 16 C til 32 C ST 18 C til 38 C T 18 C til 43 C Installation Underlaget hvorpa skabet opstilles skal veere plant Brug ikke en ramme eller lignende Skabet kan sta frit op ad en v g bygges ind i et kokkenelement eller sta side om side med andre skabe fig 2 3 600 fig 2 Skabet set fra oven Nar skabet placeres ved siden af en veeg skal man sikre at der er tilstreekkeligt plads til at d ren kan bnes sa meget at hylderne kan tr kkes ud fig 4 600 600 fig 3 1075 fig 4 Ventil
5. spare parts and service 20 Disposal arestati reeks 21 Safety instructions s Back Before use On receipt check to ensure that the ap pliance has not been damaged during transport Transport damage should be reported to the local distributor before the wine cooler is put to use Remove the packaging Clean the inside of the cabinet using warm water with a mild detergent Rinse with clean water and dry thoroughly see cleaning instructions Use a soft cloth If during transport the appliance has been laid down or if it has been stored in cold surroundings colder than 5 C it must be allowed to stabilise in an upright position for at least an hour before being switched on Installation and start up Placement For safety and operational reasons the ap pliance must not be installed outdoors The appliance should be placed on a level surface in a dry well ventilated room max 75 relative air humidity Never place the appliance close to sources of heat such as cookers or radiators and avoid placing it in direct sunlight Ambient temperature The climate class is stated on the name plate see page 7 and page 13 This specifies the optimum ambient temperature Wine coolers with winter position however function at ambient temperatures as low as 5 C Climate class Optimum room tem perature SN 10 C to 32 C N 16 C to 32 C ST 18 C to 38 C T 18 C to 43 C
6. you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling EU For more information about collec tion and recycling of old products and batteries please contact your local municipality your waste disposal service or the point of sale where you purchased the items Penalties may be applicable for incor rect disposal of this waste in accord ance with national legislation 21 For business users in the Euro pean Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union These symbols are only valid in the European Union If you wish to dis card this product please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bot tom two symbol examples This symbol might be used in combi nation with a chemical symbol In this case it complies with the requirement set by the Directive for the chemical involved Advarsel S fremt apparatet indeholder kulbrintek le middel henvises til nedenst ende retnings linier Da k lemidlet som anvendes i apparatet er en br ndbar gasart er det vigtigt at sikre at k lekredsl b og r r ikke er beska digede Standard EN378 a
7. 12 Tr k LED ledningen forsigtigt op igen nem heengselstappen 13 Flyt heengselstappen over i den mod satte side OBS Bgsningen skal ogsa flyttes med 14 Vend d ren s glassiden er nedad Bem rk Anbring noget bl dt mellem glasset og skabet for at undg ridser T tningslisten tr kkes af i den neder ste ende af d ren 15 Tr k LED ledningen op og ud 11 16 L g ledningen ned i plastprofilet og for den over til den anden side Skub ledningerne gennem det aflange hul og gennem heengselshullet Dette kan v re en sv rt at g re Sa derfor montere kun n ledning ad gangen F rst f res den ene ledning igennem og derefter tapes den anden ledning fast p den f rste og de tr kkes igen nem p n gang Husk at fjerne tapen igen 12 19 Veer opm rksom pa at ledningen ligger p nt nede i profilet og monter derefter t tningslisten igen Det er vigtigt at kontrollere at t tningsli sten sidder t t til hele vejen rundt Hvis ikke kan du opvarme listen meget forsigtigt ved hj lp af en h rt rrer og derefter trykke den ned s den danner en t t forsegling mod kabinettet V r omhyg gelig med ikke at opvarme listen s meget at den smelter 20 Fjern d rh ngselsb sning fra den anden side 21 Tr k ledningerne igennem b sningen inden de monteres i hullet til d rtappen 4 22 Vend d ren igen og anbring den i en kort afstand fra og overfor d r
8. 19 C e Ros og lette radvine 12 til 16 C e hvidvin 10 til 12 C e champagne og mousserende vine 6 til 8 C Enkelt zone indstilling for langtidslagring For langtidsopbevaring af vine anbefales en top bund indstilling pa 12 12 C Med samme indstilling i top og bund vil kglesystemet skabe en j vn temperatur i hele skabet Dog vil omgivelsernes temperatur treenge langsomt ind gennem skabets d r og sider og forarsage en lille temperaturforskel mellem top og bund Skabet vil styre ind i bunden efter den indstillede temperatur og afvigelsen vil derfor v re i toppen Forskellen vil ligge mellem 0 3 C afh n gig af omgivelsestemperaturen Afrimning reng ring og vedligeholdelse Automatisk afrimning af k le skabet Afrimning af k leskabet sker automatisk smeltevandet l ber gennem et r r ned til t vandssk len der sidder oven p kom pressoren Vandet fordamper p grund af varmen fra kompressoren T vandssk len b r g res ren engang imellem Reng ring F r reng ring p begyndes skal stikproppen fjernes fra stikkontakten Skabet reng res bedst med en opl sning af lunkent vand tilsat lidt opvaskemiddel max 65 C Anvend ikke reng ringsmidler der kan ridse Brug en bl d klud Vask efter med rent vand og t r grundigt af T vandsren den hvor kondensvandet fra fordamperen l ber ned i sidder i bunden af bagv ggen inde i skabet S rg for at den er ren Brug et desinfekti
9. another location and delivered to a recycling plant R600a Sikkerhedsanvisninger Se ogs side 2 1 2 Typeskiltet som er placeret inde i apparatet indeholder forskellige tekniske oplysninger bl a en sikkerheds advarsel med en gul trekant navn og det kemiske symbol for kglemidlet K leskabet indeholder et br ndbart k lemiddel R600a Iso butan Krav til gassikkerheden og sikker brug af k leskabet K lesystemet bag og inde i k leskabet indeholder k lemiddel Lad ikke skarpe genstande komme i kontakt med k lesystemet Brug ikke elektriske apparater inde i k leskabet B rn b r v re under opsyn for at sikre at k leskabet anvendes korrekt Brug ikke mekaniske anordninger eller andre midler til at fremskynde afrim ningsprocessen medmindre de er af en type der anbefales af producenten Bloker ikke ventilations bninger i k leskabet I tilf lde af beskadelelse af k lesystemet m du ikke bruge elektriske ap perater i n rheden ben alle vinduer for at yde en god ventilation og kontakt din lokale serviceagent eller anden fagmand De overn vnte advarselsmzerkaterne b r holde hele k leskabet levetid Brugermanualen skal altid f lge k leskabet f eks n r k leskabet blive flyttet til en anden placering eller leveres til et genbrugscenter R600a Ret til ndringer forbeholdes Reserving the right to alter specifications without prior notice 9193 226 rev 01
10. al derfor afrimes i forbindelse med almindelig reng ring eller vedligeholdelse e S frem der findes en lyskilde i appara tet fremg r udskiftning af belysningen i brugsanvisningen e V r opm rksom p at ndringer i ap paratets konstruktion vil medf re at al garanti og produktansvar bortfalder e Apparatet er udelukkende beregnet til opbevaring af vin CLASS 1 LED PRODUCT L r vinskabet at kende Belysning Kontrolpanel Kulfilter Treehylde Teetningsliste Typeskilt Pa nogle modeller er den placeret bagpa Fodspark Las Justerbare fodder Indhold AVAS El iross ee iie aeeai eienen 2 L r vinskabet at kende s 3 Inden brug 243 soerg ra herberger erne 4 Ibrugtagning og installation 4 Tekniske data 222 ran se 7 Vendbar d roman ser 8 Betjening og fUNKtION eee 16 Afrimning reng ring og vedligeholdelse18 Fejlfindingsliste nsn 19 Reklamation reservedele og service 20 Bortskaffelse isiru 21 Advaselsinstruktion ceee Bagerst Inden brug Kontroller at skabet ikke er beskadiget ved modtagelsen Transportskader skal anmel des til forhandleren inden k leskabet tages i brug Fjern emballagen Renggr skabet indven digt med lunken vand tilsat et mildt opva skemiddel Afvask med rent vand og t r grundigt af se reng ring Brug en bl d klud Hvis skabet har ligget ned under transport eller det er blevet opbevaret i kolde omgi velser koldere end 5
11. ation 127 A Det er vigtigt at skabet f r tilstr kkelig 100 mS ventilation og at der er uhindret luftcirkulation over under og omkring det l i Figurene nedenfor viser hvordan du sikrer js eee den n dvendige cirkulation omkring skabet fig 5 6 min 30 min 30 fig 5 fig 6 Afstandsstykkerne p skabets bagside sik rer den n dvendige luftcirkulation Monter de to afd kninger som f lger med skabet se fig 7 Opstilling Det er vigtigt at skabet star helt lige Man kan justere skabet ved at dreje de stil bare f dder i front op eller ned se figur 8 Kontroller med et vaterpas at skabet star lige sideveerts Tekniske data Dette apparat overholder bestemmelserne i relevante EU Direktiver herunder Lavspeen dings Direktivet 2006 95 E F og Elektro magnetisk kompatibilitet 2004 108 EF Typeskiltet som er placeret inde i apparatet indeholder forskellige tekniske oplysninger samt type og serienummer D lt fig 8 Max 85 kg Vendbar d r F lg anvisningen omhyggelig OBS F r du begynder skal du sikre dig at skabet ikke er tilsluttet str m Vi anbefaler at man er to personer til opgaven Hj lpemateriale 4 mm 6kant n gle Fladhovedet skruetr kker Torx 20 TX20 skruetr kker 1 bn d ren og afmonter de to skruer som fastholder fodsparket TX20 Vent med at afmont
12. d on rating plate will also be invalidated Transport damage discovered by the buyer is primarily a matter to be settled between the buyer and the distributor i e the dis tributor must ensure that such complaints are resolved to the buyer s satisfaction Before calling for technical assistance please check whether you are able to rectify the fault yourself If your request for assist ance is unwarranted e g if the appliance has failed as a result of a blown fuse or incorrect operation you will be charged the costs incurred by your call for technical assistance Spare parts When ordering spare parts please state the type serial and product numbers of your appliance This information is given on the rating plate The rating plate contains various technical information including type and serial numbers pa t Product numbers Disposal Information for Users on Collection EU and Disposal of Old Equipment and used Batteries These symbols on the products packaging and or accompanying mm documents mean that used electri cal and electronic products and batteries should not be mixed with general household waste For proper treatment recovery and recycling of old products and used batteries please take them to applicable collec tion points in accordance with your national legislation and the Directives 2002 96 EC and 2006 66 EC By disposing of these products and batteries correctly
13. e actual temperature in the bottles Consequently the indicator does not react on short term fluctuations of the air temperature Temperature setting The thermostat is equipped with a child lock device This device is activated by pushing the up and down buttons simultaneously After approx 3 seconds Pof flashes in the display Then the actual temperatures are shown as usual In addition the set tem peratures can be shown by pushing SET1 and SET2 respectively The child lock device is cancelled by push ing the up and down buttons simultane ously After approx 3 seconds Pon flashes in the display and the temperature can be set Temperature setting at the top of the appliance Push SET1 Then the temperature at the top of the appliance can be adjusted up and down by means of the up and down but tons The temperature can be adjusted from 8 to 22 C however so that the temperature cannot be set at a lower temperature than the actual set point for the bottom tempera ture sensor Temperature setting at the bot tom of the appliance Push SET2 Then the temperature at the bottom of the appliance can be adjusted up and down by means of the up and down buttons The temperature can be adjusted from 5 to 22 C however so that the tem perature cannot be set at a higher tempera ture than the actual set point for the upper temperature sensor Alarm devices There is a sub alarm for the lo
14. e which is a couple of degrees lower than the desired drinking temperature as the wine will be warmed slightly when it is poured into the glass Single zone setting for long term storage For long term wine storage the top and bot tom sections should both be set at 12 C With identical settings for the top and bot tom sections the controls will maintain an even temperature throughout the cabinet However the temperature in the room will gradually affect the temperature in the cabinet through its door and sides creating a slight temperature gradient from top to bottom The controls will maintain the set temperature at the bottom of the cabinet and any deviation from the setting will therefore occur at the top The difference will vary from 0 to 3 C de pending on the ambient temperature Defrosting cleaning and maintenance Automatic defrosting The wine cooler is defrosted automatically Defrost water runs through a pipe and is collected in a tray above the compressor where the heat generated by the compres sor causes it to evaporate The defrost water tray should be cleaned at intervals Cleaning Before cleaning the appliance unplug it from the main supply The cabinet is best cleaned using warm water max 65 C with a little mild detergent Never use cleaning agents that scour Use a soft cloth Rinse with clean water and dry thoroughly The defrost water channel in which condensa tion from the
15. er fodsparket 2 L g skabet ned p ryggen p et bl dt underlag for at undg skader 3 verste d rh ngsel fjernes 4 mm n gle 4 Afmonter fodsparket den indbyggede snap funktion i hver side kan l snes ved hj lp af den fladhovedede skruetraek ker 5 Leeg fodsparket med glasfronten nedad pa et bl dt underlag OBS Der ma ikke tr kkes i ledningerne 6 D rens LED ledninger afmonteres fra stikket pa fodsparket sort amp sort hvid stribet ledninger Tryk den verste las ned for at frig re ledningsenderne Bem rk sort ledning er og svarer til den r de ledning p den modsatte side Den sort hvid stribede ledning er 0 neutral og svarer til sorte ledning p den modsatte side dette er vigtigt n r ledningerne skal monteres senere 7 For at vende glasset p fodsparket skal beslagene fjernes Skruen l snes og beslaget incl skrue og bolt fjernes fra beslaget OBS Glasset er nu l st 8 L ft fodsparket og drej glasset sa lasehulllet passer med hullet i den anden side Placer fodsparket pa glasset igen og monter beslagene pa plastprofilet i begge ender igen Skruerne ma ikke overspzendes Bem rk Matrikken skal passe ind i den midterste rille 9 Tr k d ren lidt op fra h ngslet 10 Fjern l sepinden ved hj lp af den flad hovede skruetr kker 11 Tr k l secylinderen op og monter den og l sepinden igen i den modsatte side 10
16. evaporator runs is located at the bottom of the rear inside wall of the cabinet and must be kept clean Add a few drops of disinfectant e g Rodalon to the defrost water drain a couple of times a year and clean the drain using a pipe cleaner or similar Never use sharp or pointed imple ments The sealing strip around the door must be cleaned regularly to prevent discolouration and prolong service life Use clean water After cleaning the sealing strip check that it continues to provide a tight seal Dust collecting on the condenser on the rear of the cabinet the compressor and in the compressor compartment is best removed using a vacuum cleaner Fault finding Fault Possible cause Remedy The appliance is not working The appliance is switched off Power failure the fuse is blown the appliance is not plugged in correctly Press the on off switch Check that power is connected Reset the fuse Water collects in the bottom of the cabinet The defrost water pipe is blocked Clean the defrost water channel and the drain hole on the rear wall of the cabinet Vibration or bothersome noise The appliance is not level The appliance is resting against other kitchen elements Containers or bottles inside the cabinet are rattling against one another Level the appliance using a spirit level Move the appliance away from the kitchen elements or appli ances it is in contact
17. gned with the cabinet before mounting the top hinge 30 Remount the bottom front cover Place the unit vertically again and mount the tow screws see under 1 Note Important Wait approx hour before connecting the unit to the main grid Note If the door LEDs don t give out light but the top LED in the cabinet is shin aene sN aS ing its most likely that the wires are not mounted correctly into the connector See under 6 amp 25 eecoees sy a 15 Operation and function Electronic control The electronic control ensures that the temperatures set at the top and at the bot tom of the appliance are maintained This is achieved by means of an advanced control of the refrigeration system the heating ele ment and the fan The set temperature will be stored in the event of power failure The electronic control has the following functions e On off switch Light switch Temperature setting Temperature indication Alarm for too high and too low tempera tures e Door alarm The light may either be turned on constantly or only when the door is open Temperature indication The display shows the actual temperature The upper digits of the display indicate the temperature at the top of the appliance and the lower digits of the display indicate the temperature at the bottom of the appliance The temperature indicator is equipped with 16 fig 9 a built in filter which simulates th
18. illing Temperatur angivelse Automatisk afrimning e D ralarm e Alarm ved for h j og for lav temperatur Lyset kan enten v re t ndt hele tiden eller kun n r d ren er ben Temperatur udl sning Displayet viser den aktuelle temperatur Tal let verst i displayet angiver temperaturen i toppen af skabet og tallet nederst i displayet angiver temperaturen nederst i skabet 16 Temperaturvisningen har et indbygget filter som simulerer den aktuelle temperatur i flaskerne Derfor reagerer udvisningen ikke p kortvarige variationer i lufttemperaturen Temperatur indstilling Termostaten har b rnesikring Denne aktiveres ved at trykke op og ned knap perne samtidig Efter ca 3 sek blinker Pof i diplayet Herefter vises de aktuelle tempe raturer som normalt Desuden kan man se de indstillede temperaturer ved at trykke hhv SET1 og SET2 B rnesikringen annulleres ved at trykke op og ned knapperne samtidig Efter ca 3 sek blinker Pon i diplayet og temperaturen kan indstilles Temperaturindstilling i top Tryk p SET1 Herefter kan temperaturen i toppen af skabet reguleres op og ned med op og ned knapperne Temperaturen kan reguleres fra 8 til 22 C dog s ledes at temperaturen ikke kan stilles koldere end den aktuelle setpunkt for den nederste temperaturfoler Temperaturindstilling nederst i skabet Tryk pa SET2 Herefter kan temperaturen nederst i skabet reguleres op og ned med
19. ised to ensure that they do not play with the appliance Always keep the keys in a separate placeand out of reach of children Before servicing or cleaning the appli ance unplug the appliance from the mains or disconnect the electrical power supply If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Relevant for Australia Supply cord fitted with a plug complies with AS NZS 3112 Frost formation on the interior evaporator wall and upper parts is a natural phenom enon Therefore the appliance should be defrosted during normal cleaning or maintenance Please note that changes to the appli ance construction will cancel all warranty and product liability This appliance is intended to be used exclusively for the storage of wine CLASS 1 LED PRODUCT Get to know your wine cooler Lighting Control panel Charcoal filter Wooden shelf Sealing strip Nameplate On some models it is placed on the back side Kick plate Lock Adjustable feet Contents WANTING ass ssc ai vis ide iee aaea 2 Get to know your wine cooler 3 Before USC y sirenerne ennen 4 Installation and start up ssscce 4 Technical datas 42242 sleek 7 Reversible dogi enian 8 Operation and function eee 10 Defrosting cleaning and MAINTENANCE sessen ai 18 Fault finding soccci ceestetee ste cptes iissa 19 Warranty
20. l O is absolutely level sideways l e fig 8 Technical data This device complies with relevant EU directives including Low Voltage Directive 2006 95 EEC and Electromagnetic Compa Max 85 kg tibility Directive 2004 108 EC The rating name plate provides various technical information as well as type and serial number Type XXXX Serial D lt Reversible door Follow the instructions carefully NOTE Before you start the unit needs to be disconnected from the main grid We recommend that the change of door is done by a technician we recommend two persons Helping material 4 mm Allen key Flat headed screwdriver Torx 20 TX20 screwdriver 1 Open the door unscrew the two screws fixing the bottom cover Torx20 Do not remove the cover yet 2 Place the appliance on its back prefera bly on a soft foundation 3 Loosen the upper hinge and remove it 4 mm Allen key 4 Dismount the bottom cover the build in snap function in each side can be unsnapped with the flat headed screw driver 5 Place the bottom cover with glass front down on an additional support so the wires are not stretched 6 The door LED wires have to be dis mounted from the connector on the bottom cover pure black amp black white stripe wires Push the top release down to free the wire ends Note the pure black wire is and corresponds to the red wire on oppo
21. ngiver at rummet hvor apparatet installeres skal have en volumen p 1 m pr 8 g kulbrinte k lemiddel der er brugt i apparatet Dette er for at undg dannelse af brandfarlige gas luftblandinger irummet hvis der skulle opst en ut thed i k lekredsl bet M ngden af k lemiddel i apparatet er angivet p typeskiltet ADVARSEL Lad ventilations bninger i ap paratets kabinet og i eventuelt indbygningsmodul v re utild kkede ADVARSEL Anvend ikke mekaniske appa rater eller andre hj lpemidler til at fremskynde afrimnings processen udover dem som er anbefalet af fabrikanten ADVARSEL Anvend ikke elektriske appa rater inden i apparatet med mindre de er af en type som er anbefalet af fabrikanten ADVARSEL Apparatet m ikke uds ttes for regn ADVARSEL Dette apparat er ikke bereg net til at blive anvendt af sm b rn medmindre det er blevet tilstr kkeligt kontrolleret af en ansvarlig person s dan at apparatet kan anvendes for svarligt Sm b rn skal v re under opsyn for at sikre at de ikke leger med apparatet e Opbevar altid n gler et separat sted utilg ngeligt for b rn e Tr k stikket ud af stikkontakten f r repa ration eller reng ring af apparatet e Hvis netledningen er beskadiget skal den udskiftes af producenten producentens serviceagent eller anden fagmand for at undg fare e Dannelse af rim p den indvendige fordamperplade og de verste dele er normalt Apparatet sk
22. oblong hole and through the new hinge hole This can be a bit tricky so try to mount only one wire first 18 Then tape the second wire end to the first wire and pull them both fully through remove tape subsequently 12 I 19 Make sure the wires are fitted into the BED plastic groove and mount the gasket It s important to check that the sealing strip provides a tight seal all the way round If it does not carefully heat the strip all the way round using a hair dryer Then ease the strip slightly outwards so that it forms a tight seal against the cabinet Be careful not to heat the strip so much that it melts 20 Dismount the door hinge bushing and mount it on opposide side 21 Pull the wire through the bushing before mounting it into the door hinge hole 4 22 Reverse the door again and displace it a little on the cabinet proportion to the z botton hinge 4 F pem 13 23 Pull the two wires through the bottom hinge pin 24 and through the wire hole in the pla stic column 25 Remount the wires se under 6 and make sure that they are firmly secured 26 Pusch the door back in place over the hinge pin and pull the wires simultane ously so the wire do not get stuck 14 27 Dismount the top door bushing and mount it on opposite side 28 Dismount the plastic caps on the top of the cabinet and mount them on opposite side 29 Make sure that the door is ali
23. onsmiddel som f eks rodalon der skal dryppes i t vandsafl bet et par gange om ret Rens med en piberenser eller lignende Brug aldrig skarpe eller spidse genstande T tningslisten rundt ved d ren kr ver j vnlig reng ring for at undg misfarvning og sikre lang holdbarhed Brug rent vand Efter reng ring af d rens t tningsliste b r du kontrollere om den fortsat slutter t t P rygkondensator kompressoren og i kompressorrummet fjernes st vet bedst med en st vsuger 18 Fejlfindningsliste Fejl Mulig rsag Afhj lpning Skabet virker ikke Skabet er slukket Str msvigt sikringen er sl et fra netstikket er ikke sat rigtigt i Tryk p t nd sluk knappen Kontroll r om str mmen er tilsluttet Sikringen skal v re sl et til Der l ber vand i bunden af k leska bet T vandsafl bsr ret er tilstoppet Rens t vandsrenden og afl bs hullet i bagv ggen Vibrationer eller generende st j Skabet st r sk vt Skabet hviler op mod andre k k kenelementer Beholdere eller flasker ber re hinanden i skabet Indstil skabet med et vaterpas Ryk skabet v k fra k kkenel ementerne eller apparater som st r umiddelbart op ad skabet S rg for afstand mellem flasker og eller beholdere Kompressor k rer konstant H j rumtemperatur S rg for god ventilation Styringen viser P1 Topf leren er afbrudt eller kort sluttet Tilkald
24. ravene for det direktiv som er blevet fastlagt for det p g ldende kemikalie Safety instructions See also Warning page 2 1 There is a name plate inside the cabinet The name plate provides various technical information and a safety notice with a yellow flame triangle label name and chemical symbol of the refrigerant The refrigerator contains flammable refrigerant R600a iso butane Re quirements to ensure gas safety and safe use of refrigerators The refrigeration system behind and inside the refrigerator contains refrigerant Do not allow any sharp objects to come into contact with the refrigeration system Do not use other electric appliances inside the refrigerator Children should be supervised to ensure that the refrigerator should be used properly Do not use the mechanical devices or other means to accelerate the defro sting process unless they are of the type recommended by the manufactu rer Do not block the openings on the circumstances of the refrigerator In case of having damaged the refrigerant circuit do not use electric items or fire equipments nearby and open all windows to provide good ventila tion Please also contact your local maintenance agent to follow up The warning labels mentioned above should be kept throughout the life of the refrigerator The user manual should be handed over to any person who would use or handle the refrigerator whenever the refrigerator would be transferred to
25. retten V r opm rksom p at ved indgreb i apparatets opbygning og ved ndring af apparatets komponentbestykning bortfalder garanti og produktansvar og apparatet kan ikke lovligt anvendes Godkendelse anf rt p meerkeskilt er ligeledes ugyldig Transportskader der konstateres hos for brugeren er prim rt en sag mellem forbru ger og forhandler dvs forhandler m drage omsorg for at forbrugeren stilles tilfreds inden du tilkalder serviceassistance bedes du kontrollere de fejlmuligheder du selv kan afhj lpe Se brugsanvisningen S fremt dit krav om afhj lpning er ube rettiget eksempelvis hvis apparatets svigt skyldes en sprunget sikring eller en fejlbetjening m du selv betale de omkost ninger der er forbundet med at have tilkaldt serviceassistance Reservedele Angiv venligst type og serienummer samt produkt nummer n r du bestiller reserve dele Disse oplysninger finder du p typeskiltet Typeskiltet indeholder forskellige tekniske oplysninger samt type og serienummer Husk altid at bruge autoriserede handveer kere hvis der er noget der skal repareres eller udskiftes x Produkt nr Bortskaffelse Brugerinformation om indsamling og bortskaffelse af elktronikskrot og brugte batterier A Disse symboler p produkter embal lage og eller ledsagedokumenter betyder at brugte elektriske og elektroniske produkter og batterier ikke m smides ud som almindelig
26. service Hele skabet styrer efter varmeste setpunkt indtil fejlen er udbedret Styringen viser P2 Bundf leren er afbrudt eller kortsluttet Tilkald service Hele skabet styrer efter varmeste setpunkt indtil fejlen er udbedret 19 Reklamation reservedele og service Reklamationsretten S fremt der konstateres fejl ved produktet kan De over for leverand ren g re brug af reklamationsretten if lge g ldende lovgiv ning Producenten skal for egen regning afhj lpe fabrikations og materialefejl der konstateres ved apparatets normale brug under foruds tning af at apparatet er k bt som fabriksnyt i Danmark For Gr nland og F r erne g lder s rlige bestemmelser S fremt det sk nnes n dvendigt at appara tet indsendes til v rksted sker indsendelse og returnering for producentens regning og risiko Der er ikke d kning for fejl eller skader direkte eller indirekte opst et ved fejlbetje ning misbrug mangelfuld vedligeholdelse forkert indbygning opstilling eller tilslutning Det samme g lder for brand ulykke lyn nedslag speendingsvariationer eller andre elektriske forstyrrelser som f eks defekte sikringer eller fejl i forsyningsnettets elektri ske installationer Reparationer udf rt af andre end de anviste reparat rer og i det hele taget fejl og skader som leverand ren kan godtg re skyldes andre rsager end fabrikations og materialefejl er ikke omfattet af reklamati ons
27. site side The black white stripe wire is 0 neutral and corre sponds to the black wire on the opposite side this is important when the wires are to be mounted later 7 To reverse the bottom glass the brackets need to be removed Loosen the screw and the bracket incl screw and bolt slides of the plastic profile NOTE Now the glass is loose 8 Lift the bottom sheet metal part and turn the glass so the lock hole fits the other ends round hole concentric Place the sheet metal part on the glass again and mount the brackets onto the plastic pro file in each end again Don t over tighten the screws Note The nut has to fit into the centre groove 9 The door has to be moved up from the hinge 10 Unscrew the lock pin using the flat hea ded screwdriver and remove it 11 Pull up the lock cylinder and refit both lock cylinder and lock pin in opposite side 10 12 Pull the LED wires gently out of the bot tom hinge pin 13 Dismount the bottom hinge pin and fit it on the opposite side Note The bush must also be moved 14 Turn the door so the glass side is down Note Place something between the glass and the other surface cabinet so scratch are minimized Then loosen the gasket on the low end of the door by pulling 15 Pull the LED wires up and out 11 16 Replace the wires into the plastic groove and lead them to the other side 17 Push the wires through the
28. t husholdningsaffald S danne gamle produkter og batterier skal indleveres til behandling genvinding resp recy cling i henhold til g ldende nationale bestemmelser samt direktiverne 2002 96 EF og 2006 66 EF Ved at bortskaffe s danne produkter og batterier p korrekt vis hj lper du med til at beskytte v rdifulde ressourcer og im deg de negative p virkninger af det menneskelige helbred og milj et som vil kunne v re f lgen af usagkyndig affaldsbe handling nsker du mere udf rlig information om indsamling og recycling af gamle produkter og batterier kan du hen vende dig til din kommune depone ringsselskabet eller stedet hvor du har k bt produkterne Usagkyndig bortskaffelse af elektro nikskrot og batterier kan eventuelt udl se b deforl g 21 EU Pb z For kommercielle brugere i Den Europ iske Union Nar du nsker at kassere elektriske eller elektroniske apparater bedes du henvende dig til din forhandler eller leverand r for n rmere information Information om bortskaffelse i lande uden for Den Europ iske Union Disse symboler g lder kun inden for Den Europ iske Union Hvis du nsker at afh nde dette produkt skal du rette henvendelse til de lokale myndigheder eller din forhandler Her kan du f oplysninger om hvordan du bedst kommer af med produktet Information om batterisymbol Dette symbol kan optr de sammen med et kemisk symbol I s fald opfyl der det k
29. tappen lt _ r a _ a 13 14 23 Traek ledningen igennem derheengslet 24 og igennem ledningshullet i plastemnet 25 Monter ledningen igen i stikket se under pkt 6 og tjek at de er fastgjort korrekt 26 Skub d ren ned pa plads over b snin gen samtidig med at der treekkes for sigtig i ledningerne sa de ikke kommer i klemme 27 Flyt basningen i toppen af d ren over pa den modsatte side der sidder maske n i forvejen 28 Flyt afdeekningspropperne i toppen af skabet over pa den modsatte side 29 Veer opm rksom pa at d ren ligger lige pa kabinettet for topheengslet monteres igen 30 Monter fodsparket igen Rejs skabet op og skrue de to skruer i igen se under pkt 1 OBS VIGTIGT Vent ca 1 2 time inden skabet tilsluttes stram OBS Hvis LED dgrlyset ikke lyser men den verste LED lys i skabet lyser er det mest sandsynlige at ledningerne ea 88383830 S su ikke er monteret korrekt i stikket N Tjek pkt 6 amp 25 15 Betjening og funktion Elektronisk styring Den elektroniske styring s rger for at skabet holder de indstillede temperaturer i top og i bund af skabet Dette opn s ved en avanceret styring af k lesystem varmele geme og ventilator Efter en evt str mafbrydelse huskes den indstillede temperatur Den elektroniske styring har f lgende funktioner T nd sluk knap Lyskontakt Temperaturindst
30. w temper ature sensor and an excess alarm for the high temperature sensor The alarm consists of a beeper and a warn ing on the display 9 Alarm for high temperature beep sound alternating display of HtA and actual temperature Alarm for low temperature beep sound alternating display of LtA and actual temperature The alarm temperature depends on the set points The beep sound can be cancelled by push ing a random thermostat button Push the on off button to erase the display alarm first for cancelling the alarm then again for restarting the compressor Door alarm When the door has been open for more than 2 minutes the door alarm is activated 17 Light To turn off the lights press once e Permanent lighting For presentation purposes of your wine you can turn the lights permanently Please press the light switch image XE twice To switch off the lights press on 3 again Two zone setting for serving temperature Typical serving temperature settings for the top and bottom sections are 16 C and 6 C respectively With these settings a suitable temperature gradient will be achieved in the cabinet for the storage of various types of wine distributed from top to bottom as follows e heavy red wines 16 to 19 C e ros and light red wines 12 to 16 C e white wines 10 to 12 C e champagne and sparkling wines 6 to 8 C It is recommended that wine be served at a temperatur
31. with Move containers and or bottles apart Compressor runs continuously High room temperature Ensure adequate ventilation P1 is shown on the display The upper sensor is disconnect ed or short circuited Call for service The temperature within the entire cabinet is main tained at the higher of the two setpoints until the fault has been corrected P2 is shown on the display The lower sensor is disconnected or short circuited Call for service The temperature within the entire cabinet is main tained at the higher of the two setpoints until the fault has been corrected 19 Warranty spare parts and service Warranty disclaimer Faults and damage caused directly or indirectly by incorrect operation misuse insufficient maintenance incorrect building installation or mains connection Fire ac cident lightening voltage variation or other electrical interference including defective fuses or faults in mains installations Repairs performed by others than approved service centres and any other faults and damage that the manufacturer can sub stantiate are caused by reasons other than manufacturing or material faults are not covered by the warranty Please note that changes to the construc tion of the appliance or changes to the component equipment of the appliance will invalidate warranty and product liability and the appliance cannot be used lawfully The approval state
Download Pdf Manuals
Related Search