Manual
Contents
1. associated with any particular installation the device manufacturer cannot assume responsibility or liability for actual use based on the examples and diagrams Before making any decision or taking any action that might affect your equipment you should consult a qualified professional advisor ORO SIM IPE DER Product of USA2. device memory e Turn device power Off e Press and hold OK key then press hems w de Attempt r Characeae SUCCeSSTU ir e c Dynamic a RN N T Lr eres ho Wed 1 UNKNOWN is arget IP ce oh and release Cancel key a Ooo ta Vee T limea Out 7 Ea e y e yp a Py ae Ror m Network Setup neply ms e Hold OK during countdown e Release OK when prompted 7 Selecting Target device address from the previously used list 1 Ayes g rr A Pn pe New Target Addi 8 Assign an IP address using BOOTP or DHCP requests Tat r an tic Dynamic 9 Replacing IP address for Target that already has a Static IP address Assigned The device will attempt to connect to the Target Device using Ethernet IP protocol by ODVA Please note that not all target devices support Ethernet IP protocol DISCLAIMER This device is intended to provide general assistance with Industrial Ethernet setup troubleshooting testing and application development It should not be permanently used in live production systems Accordingly production system must be tested and commissioned with real instruments to ensure safe and reliable operation IN NO EVENT SHALL THE DEVICE MANUFACTURER BE LIABLE FOR ANY DAMAGES OF ANY KIND INCLUDING DIRECT INDIRECT INCIDENTAL CONSEQUENTIAL LOSS OF PROFIT OR DAMAGE The examples and diagrams in this manual are included for illustrative purposes only Because of the many variables and requirements
3. IP explorer Professional Professional MAC Address 001D9C 398CBF IP Address 192 168 100 137 1756 ENBT A Ver 6 006 SN 00118E46 Quick Start Guide Revision 2014 02 WWW PLCTOOLS COM 10 Setting Target device to Static Disable BOOTP DHCP After the IP address is assigned to the Target Device using BOOTP DHCP it s important to disable BOOTP DHCP or make the IP static If this is not done the target device will not have an IP address after its power is cycled eee IEA Connecting to larget Device anth ID AddAracc with IP Address 1090 1202 1n te 192 168 100 43 Ci icrrac SUCCeSS 1 Ethernet Connection Standard straight through or Crossover Ethernet cables can be used for a direct connection to the Target Device Ethernet connection supports 10 100 Mbps Full Half Duplex Auto Negotiation with automatic crossover detection Connection indicator shows connection state and speed information 5 Assign Network Parameters Mask and Gateway settings will be used for target device as well Fai Important Mask and Gateway settings will be also used for the target device 6 Entering a target device IP address 2 Batteries The device uses two AA size Ni MH rechargeable batteries Alkaline batteries can be used with reduced battery life Battery indicator provides estimated remaining battery Capacity 3 Navigation keys The universal set of keys allows easy menu en
4. a o navigation and address change 4 Turn Device On Off To turn device ON press Cancel key once To turn Device OFF press and hold Cancel key until shutdown message shown then release Cancel key Device will automatically turn power OFF after 3 minutes of inactivity or if batteries are low Last used IP address will be offered as a template for the new selection Important Own IP Address Gateway Address and Target device IP addresses must be on the same subnet for this device to function correctly An error message will be displayed if the addresses are not on the same subnet Important Target Device IP Own IP Address and Gateway Address must be on the same subnet or this feature will not be active An error message will be displayed if the addresses are not on the same subnet 13 Detecting an Unknown IP Address This device will attempt to detect unknown IP address of your target rs ry 7 J Fafa ia 5 f IU j f A e i amic i i 1 Vy E DAE rget IP Important It may take up to a few minutes to display the IP address Not every IP address can be detected 11 Setting to Dynamic Enable BOOTP DHCP This feature allows you to set target device to use BOOTP DHCP if device is currently set to Static 15 Device information fessional CIA IDC IM P L 14 Reset IP Explorer to Factory Defaults This will clear all Network Setting and saved IP addresses from the
Download Pdf Manuals
Related Search
Manual manual manualslib manual car manuale digitale manually meaning manual timesheet manual transmission manual wheelchair manually update your device drivers windows manual arts high school manual for courts martial manual definition manual labor manual lawn mower manual muscle testing manually register devices with autopilot manual muscle testing grades manualidades manual transfer switch manual therapy cpt code manual blood pressure cuff manual transmission cars for sale manual handling manual digital manual autopilot enrollment