ICMT-4000 - Athens Technical Specialists Inc.
Contents
1. lt 15 Vrms Load Switch Coils LSC Active gt 105 of threshold Inactive lt 95 of threshold An inactive state of the RED YEL and GRN inputs OR the LSC input on any channel for 1000 ms or more shall cause a Lack of Signal Fault and produce a Failed State Action FSA YEL or GRN inputs that are active on conflicting channels for 500 ms or more shall cause a Conflict Fault and produce a FSA Note The CMU must use a Serial Memory Key programmed as described in Section 4 1 5 2 AMU Tests When testing an AMU the Tester sets all of the AMU voltage inputs to known values The Tester then simulates a CMU and sends a valid Type 2 status request command frame to the AMU The Tester then waits for Page 8 of 12 Rev 1 3 ICMT 4000 User s Manual 5 Test Descriptions a Type 130 status response frame The Tester checks for the appropriate address and the correct checksum If the frame is valid the voltage reported by the AMU is then compared to the known value suppled by the Tester If the value reported is within 2 Vrms of the known value the test passes ICMT 4000 User s Manual Page 9 of 12 6 Service and Calibration 6 Service and Calibration The ICMT 4000 has no user serviceable parts Under no circumstances should the user attempt to open the enclosure If the tester appears to be malfunctioning contact ATSI to make arrangements for repair See the Limited Warranty and Liability section of this manual2. 174 0 AMU Position 3 byte 175 14 AMU Position 4 byte 176 0 All other parameters bytes should be set to their default values To test a CMU Slide it into the appropriate slot on the tester From the ICMT 4000 Interface software click on the Test Setup tab and fill in the data Make sure the 212 CMU option is selected Click on the Run Tests tab To run a complete certification test make sure the Certification button is selected If you would like to select the individual tests that should be ran select the Diagnostics button and then click the Select Tests button to select the tests Click the Start button When the test is done click Save button to save the test report 4 2 Testing AMU The AMU does need any special configuration To test an AMU Slide the device into the appropriate slot on the tester From the ICMT 4000 Interface software click on the Test Setup tab and Page 6 of 12 Rev 1 3 ICMT 4000 User s Manual 4 Running Tests fill in the data Make sure the 214 AMU option is selected on the Run Tests tab To run a complete certification test make sure the Certification button is selected If you would like to select the individual tests that should be ran select the Diagnostics button and then click the Select Tests button to select the tests Click the Start button When the test is done click Save button to save the test report ICMT 4000 Use
3. for details ATSI strongly recommends that each Tester be calibrated yearly yearly calibration will verify that your Tester is operating within the original manufacturers specifications and provide you with a detailed calibration report for documentation Please visit www atsi tester com for the latest pricing of calibration services and extended maintenance plans Page 10 of 12 Rev 1 3 ICMT 4000 User s Manual 7 Limited Warranty and Liability 7 Limited Warranty and Liability The ICMT 4000 ITS Cabinet Monitoring System Tester Product distributed by Athens Technical Specialists Inc ATSI is warranted to the original purchaser Purchaser to be free of defects in materials and workmanship for a period of one year from the purchase date stated on the invoice Within this period in the event of a defect malfunction or other failure of the Product while the custody of the Purchaser ATSI will remedy the defect or cause of failure without charge to the Purchaser The Purchaser s sole remedy is restoration of product operation ATSI accepts no liability for incidental or related expenses Under no circumstances will ATSI s liability exceed the purchase price for items claimed to be defective This Limited Warranty does not extend to any Product that has been damaged or rendered defective as a result of accident misuse abuse modification of the product or service by anyone other than ATSI EXCEPT AS EXPRESSLY S
4. wizard Note Do not forget to install the ATSI Tester USB device driver for ICMT 4000 3 3 ICMT 4000 USB Driver Installation To communicate with the ICMT 4000 an ATS Tester USB driver needs to be installed The same driver is used with several ATSI products and is included on the software installation CD The latest version of the driver can also be downloaded from our website www atsi tester com The driver installation package is also copied to the computer during the software installation To install the USB driver insert the software installation CD that came with your ICMT 4000 Click on the ATSI USB Device Driver button and follow the instructions to install the driver If you do not have the software installation CD the USB driver may be downloaded from www atsi tester com ICMT 4000 User s Manual Page 5 of 12 4 Running Tests 4 Running Tests Before running a test make sure the tester is plugged in to a standard 120V AC outlet and the power switch is turned on Connect the tester to the computer with the USB cable provided See section 3 3 ICMT 4000 USB Driver Installation on how to install the USB driver Start the ICMT 4000 Interface software See section 3 2 ICMT 4000 Interface Software Installation on how to install the software 4 1 Testing CMU For the CMU the following configuration should be programmed into the Serial Memory Key AMU Position 1 byte 173 14 AMU Position 2 byte
5. ET FORTH IN THIS WARRANTY ATSI MAKES NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICUALR PURPOSE OF THE PRODUCT AND ANY DEVICE TESTED BY THE PRODUCT ATSI EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS EXPRESS LIMITED WARRANTY Warranty Repair To return the Product for repairs covered under the Limited Warranty Request a Return Merchandise Form by phone fax or email from the ATSI Service Department or complete the form at www atsi tester com Return the Product along with the completed form with prepaid postage to ATSI 8157 US Hwy 50 Athens OH 45701 Phone 740 592 2874 Fax 740 594 2875 Email service atsi tester com ICMT 4000 User s Manual Page 11 of 12 This page is left intentionally blank Page 12 of 12 Rev 1 3 ICMT 4000 User s Manual ITS Cabinet Monitoring System Tester Model ICMT 4000 User s Manual Revision 1 3
6. ICMT 4000 ITS Cabinet Monitoring System Tester AI User s Manual Revision 1 3 Table of Contents Table of Contents 1 Explanation of Symbols Terms and Abbreviations 2 2 Safety enne 4 ICMT 4000 5 3 1 Computer 5 3 2 ICMT 4000 Interface Software Installation 5 3 3 ICMT 4000 USB Driver 5 4 Running Tests teneor a ala T7 4 1 Testing 7 4 2 Testing debet ted ele T7 5 Test Descriptions i oet dis 8 5 1 CMU TES St a 8 5 2 AMUTeStS c tome la e cuted a 9 6 Service and 2 2 2 98 10 7 Limited Warranty 20 11 ICMT 4000 User s Manual Rev 1 3 Page 1 of 12 1 Explanation of Symbols Terms and Abbreviations 1 Explanation of Symbols Terms and Abbreviations Graphical Symbols The following symbols are used on the ICMT 4000 enclosure and in this manual Anytime one of these symbols is encountered the user should be aware of the condition described here next to each symbol Caution Risk of danger Read the Users Manual before operating the ICMT 4000 Caution Risk of electric shock Terms and Abbreviations The following i
7. bject into the AMU CMU slot Do not attempt to test devices that have been subject to lightning strikes or other severe electrical stress Only test AMU or CMU devices that are designed according to the ITS Standard Specification for Roadside Cabinets Only use the power cord provided with the tester The tester should only be powered from 120V AC Page 4 of 12 Rev 1 3 ICMT 4000 User s Manual 3 ICMT 4000 Installation 3 ICMT 4000 Installation 3 1 Computer Requirements Windows XP minimum At least one available USB port Adobe Acrobat Reader must be installed This can be downloaded for free at www adobe com 3 2 ICMT 4000 Interface Software Installation Installation of the software is a simple process However it may require an administrative access to the computer The ICMT 4000 comes with a software CD which can be used to install the software If the CD is not available the software can be downloaded from the Internet To download the software visit our website www atsi tester com install the software from a CD insert it into the CD drive of the PC A start up screen should open automatically In the start up screen click ICMT 4000 button then follow the instructions in the software installation wizard To install the software that was downloaded from our website double click the downloaded executable file to run the installation Follow the instructions in the software installation
8. r s Manual Page 7 of 12 5 Test Descriptions 5 Test Descriptions All of the AMU and CMU tests are based on the Intelligent Transportation System ITS Standard for Roadside Cabinets v01 02 17b November 16 2006 Section 4 4 and 4 5 It is the intent of ATSI to test all of the requirements of the aforementioned standard as thoroughly as possible based on our best interpretation of the standard Each individual jurisdiction state city county may have specific requirements or practices that are routinely followed which may deviate from the ITS standard or ignore certain parts Furthermore each AMU CMU manufacturer may have certain features enabled or disabled in their devices to accommodate such deviations from the ITS Standard Therefore some tests may have the option to disable the testing of certain AMU CMU functions It is the responsibility of the user to determine if the test is appropriate for their local requirements 5 1 CMU Tests When testing a CMU the Tester simulates an AMU The Tester waits for the CMU to send a Type 2 status request command The Tester checks for the appropriate address and the correct checksum and then responds with a Type 130 status response frame The test also verifies that the CMU recognizes the proper thresholds for determining active and inactive AMU input signals The required thresholds are RED Active gt 70 Vrms Inactive lt 50 Vrms GRN YEL Active gt 25 Vrms Inactive
9. s a list of terms and abbreviations used throughout the text of this manual along with the definition Term or Abbreviation Definition ITS Intelligent Transportation System mA milliamperes thousandths of an amp ms milliseconds thousandths of a second NEMA National Electrical Manufacturers Association PC Personal computer Tester The ATSI ICMT 4000 ITS Cabinet Monitoring System Tester Transfer Relay An electro mechanical relay used in a traffic signal electrical cabinet TR Transfer Relay see definition of Transfer Relay VDC Volts DC Page 2 of 12 Rev 1 3 ICMT 4000 User s Manual 1 Explanation of Symbols Terms and Abbreviations Term or Abbreviation Definition Vrms Volts RMS root mean squared ICMT 4000 User s Manual Page 3 of 12 2 Safety Information 2 Safety Information IMPORTANT SAFETY INFORMATION READ BEFORE ATTEMPTING TO USE THE ICMT 4000 The ICMT 4000 Tester should only be used by qualified and authorized traffic signal technicians who are familiar with generally accepted electrical safety practices as well as local and national safety codes To avoid possible electric shock burns or fire read all information contained in this manual before attempting to use the Tester Do not use the Tester around explosive gas vapor or dust Do not use the Tester in a wet environment Do not attempt to open any part of the Tester enclosure Do not put hands or place any other o
Download Pdf Manuals
Related Search