Piccolo - User Manual
Contents
1. The installation and set up of the water heater must be carried out by a competent person in conformity with the applicable norms in force and with any provisions set forth by local authorities and public health bodies Warning this is an open outlet appliance no pressure and can be installed in one point of use only The electrical and plumbing connections must be made in compliance with the applicable norms in force The appliance heats water to a temperature below boiling point It must be linked up to a mains water supply according to the appliance performance levels and capacity Before connecting the appliance it is first necessary to Check whether the characteristics please refer to the data plate meet the customers requirements Make sure the installation conforms to the IP degree of protection against the penetration of liquids of the appliance according to the applicable norms in force Read the instructions provided on the packaging label and on the appliance data plate Installing the appliance This appliance was designed to be installed only inside buildings in compliance with the applicable norms in force Furthermore installers are requested to keep to the following advice in the presence of 27 Damp do not install the appliance in closed unventilated and damp rooms Frost do not install the appliance in areas where the temperature may drop critically and there may be a risk that ice may form2. damp cloth soaked in soapy water O See warning nos 22 23 Operation To turn the water heater on insert the plug into the wall socket or switch on the bipolar switch The pilot lamp A fig 4 only stays on during the heating cycle during this time the expanding water could cause some water to trickle from the tap this is completely normal and does not mean the tap is faulty Do not screw the taps too tightly to prevent damaging their seals The thermostat will automatically disable the heating element as soon as the selected water temperature is reached During the final stage of heating it is normal for a few cycles of thermostat starting and stopping to take place During normal operation the electric heating element may make a little noise inside the appliance which is due to the heat exchange the plumbing connections may also become hot to the touch Adjusting the operating temperature The temperature of the water can be selected on the knob F fig 6 and can be adjusted from 40 to 80 C approximately We recommend you set the temperature of the water heater to 60 C to reduce the formation of limescale reduce heat dispersion avoid the risk of bacteria proliferation 31 Fig 1 I Attenzione Utilizzare un rubinetto per scaldacqua sopralavello D Vorsicht Mischbatterie f r bertischwarmwasserspeicher ben tzen GB Warning To use mixing tap for above sink water heater F Attention
3. the effects caused by lightning Before turning the appliance on make sure the supply voltage complies with the value stated on the appliance data plate and that the appliance itself is filled with water If the appliance is not supplied with a power supply cable make a fixed connection to the mains using a rigid pipe or cable for permanent installation Starting and testing the appliance Before powering the appliance fill the tank up with mains water Set the knob F fig 6 to the desired position plug the appliance into the socket or switch the main switch to ON Check the appliance operation until the end of the first heating cycle indicated by the relative pilot lamp turning off During the heating phase the water expansion could cause some trickling from the tap this is completely normal and does not mean the tap is faulty Do not screw the taps too tightly to prevent damaging their seals In the event of a malfunction read the paragraph regarding the MAINTENANCE REGULATIONS Adjusting the operating temperature The temperature of the water can be selected on the knob F fig 6 and can be adjusted from 40 to 80 C approximately We recommend you set the temperature of the water heater to 60 C to reduce the formation of limescale reduce heat dispersion avoid the risk of bacteria proliferation Anti freeze function If the temperatures in the room where the appliance is installed can reach particularly low va
4. Piccolo ARKS 50 Open outlet water heater Other languages have been omited from this manual for ease of use ATTENZIONE Scaldacqua a scarico libero Lo scarico agisce da sfiato usare rubinetti adatti per scaldacqua a scarico libero Prima di accendere l apparecchio assicurarsi che esso sia pieno d acqua aprire il rubinetto dell acqua calda a sinistra e attendere fino alla fuoriuscita dell acqua ACHTUNG Offener Speicher Dieser Speicher arbeitet drucklos Spezialarmaturen verwenden Vor der elektrischen Inbetrieonahme mu sicher gestellt sein da der Speicher mit Wasser gef llt ist Dazu mu mann das HeiBwasserventil links ffnen und abwarten bis Wasser aus dem Auslauf kommt WARNING Open outlet water heater The outlet acts as a vent use mixing taps suitable for open outlet water heaters only Before switching on the appliance make sure it is full of water open the hot water tap to the left and wait until water flows through ATTENTION Chauffe eau coulement libre Ce chauffe eau travaille hors pression Utiliser une robinetterie speciale S assurer que l appareil est rempli d eau avant la mise sous tension Pour se faire ouvrir le robinet d eau chaude cot gauche jusqu a ecoulement OPGELET Dit toestel mag enkel met open zonder druk worden geinstalleerd Op de afvoerpijp mogen derhalve geen straalregelaars gummislangen of afsluitkranen worden bevestigd Voor dat men de boiler
5. RESET SYSTEM 0104 Litograf s r l Jesi 029 1 60 008 2 01
6. Sunlight do not expose the appliance to direct sunrays even in the presence of windows Dust vapours gas do not install the appliance in the presence of particularly aggressive atmospheres such as acidic vapours dust or those saturated with gas Electrical discharges do not install the appliance directly on electrical supplies that aren t protected against sudden voltage jumps See warning no 26 See warning no 9 In the case of walls made of bricks or perforated blocks partition walls featuring limited static or masonry different in some way from those stated you first need to carry out a preliminary static check of the supporting system Install the appliance using the special bracket provided in the box fastening it using 2 screws Rawlplugs measuring 6 mm in diameter See warning no 10 Local norms could set forth restrictions regarding the installation in a bathroom environment Therefore keep to the minimum distances foreseen by the applicable norms in force The appliance should be installed as close as possible to the point of use to limit heat dispersion along the piping See warning no 20 Plumbing connection Before making the plumbing connection you must arrange for the system to be cleaned thoroughly to eliminate any residue or dirt that could compromise the proper operation of the water heater Connect the water heater inlet and outlet to resistant pipes or pipefittings as well as to the opera
7. Utiliser une robinetterie pour chauffe eau modele sur vier NL Opgelet gebruik een kraan voor een boiler model boven de gootskeen H Figyelem Csaptelep a mosogat f l tti vizmelegit h z CZ Upozornin Pouzivat baterie pro typ ohgiva e s umistinim nad dgez PL Uwaga nalezy zamontowa baterie mieszajaca przeznaczong do ogr zewaczy instalowanych nad zlewem R Acqua calda rosso Warmwasser rot Hot water red Eau chaude rouge Warmwater rood Melegv z piros Tepl voda erven Woda gor ca czerwony max 1000 Kaltwasser blau Cold water blue Eau froide bleu Koudwater blauw y E 7 Hidegviz k k Studen voda modr Woda zimna niebieski B Acqua fredda blu 83 Fig 2 I Attenzione Utilizzare un rubinetto per scaldacqua sottolavello D Vorsicht Mischbatterie f r Untertischwarmwasserspeicher ben tzen GB Warning To use mixing tap for under sink water heater F Attention Utiliser une robinetterie pour chauffe eau modele sous vier NL Opgelet gebruik een kraan voor een boiler model boven de gootskeen H Figyelem Csaptelep mosogat alatti vizmelegit h z CZ Upozornini Pouzivat baterie pro typ ohgiva e s umistinim pod dgez PL Uwaga nalezy zamontowa baterie mieszajaca przeznaczona do ogr zewaczy instalowanych nad zlewem R Acqua calda rosso Warmwasser rot Hot water red Eau chaude rouge Warmwater rood Mele
8. ance manufacturer will not be held responsible for any damage caused by the lack of earthing of the system or for faults in the electricity supply 28 See warning no 24 Check that the system is suitable for the maximum power absorbed by the water heater please refer to the data plate and that the cross section of the electrical connection cables is suitable and no less than 1 5 mm The power supply cable type HO5 W F 3x1 5 8 5 mm in diameter should be inserted in the corresponding hole X fig 6 situated in the vicinity of the control knob and feed it until it reaches the thermostat slots T fig 6 The electrical connection should be made directly on the terminals D fig 6 of the thermostat respect the L N polarity The appliance is fitted with a cable and plug For installations without a plug use a bipolar switch in conformity with the applicable norms in force fused with a minimum contact opening of 3 mm The appliance must be earthed and the earth wire yellow green colour should be fastened to the special faston on the heating element and marked with the amp PE fig 6 Secure the power supply cable in place using the special cable clamp provided with the appliance O See warning no 11 The use of multiplugs extensions or adaptors is strictly prohibited It is strictly forbidden to use the piping from the plumbing heating and gas systems for the appliance earthing connection The appliance is not protected against
9. and equipment All operations on the inside of the appliance must be performed with the necessary caution in order to avoid abrupt contact with the sharp parts 6 Warning Risk Personal injury from the falling splinters or fragments inhalation of dust shocks cuts pricks and abrasions Damage to the appliance or surrounding objects from falling splinters knocks and incisions Personal injury from electrocution falling splinters or fragments inhalation of dust shocks cuts pricks abrasions noise and vibration Damage to the appliance or surrounding objects from falling splinters knocks and incisions Personal injury from falling from a height or from cuts stepladders shutting accidentally Personal injury from falling from a height Personal injury from falling from a height Personal injury due to knocks stumbling and injuries Personal injury from electrocution falling splinters or fragments inhalation of dust shocks cuts pricks abrasions noise and vibration Personal injury from cuts pricks and abrasions Do not use any insecticides solvents or Damage to the plastic and painted parts aggressive detergents to clean the appliance normal domestic use 2 Do not use the appliance for any use other than Damage to the appliance due to operation overload Damage to objects treated inappropriately Do not allow children or inexperienced people Damage to the appliance due to improper to
10. d unplugging it or switching Electrocution from live components the dedicated switch off Install the appliance on a solid wall that is not Noisiness during operation subjected to any vibrations Electrocution from contact with live wires Explosions fires or intoxication from the When piercing the wall for installation take card discharge of gas leaking from damaged piping not to damage any electrical wiring or existing piping Damage to existing installations Flooding due to water leaking from damaged piping Electrocution from contact with live wires Protect all connection pipes and cables in order A to prevent their being damaged Flooding due to water leaking from damaged piping Make sure the installation site and any systems Electrocution from contact with live wires A to which the appliance must be connected installed incorrectly comply with the applicable norms in force Damage to the appliance due to improper operating conditions Personal injury due to the appliance falling Al SEET Damage to the appliance or any objects underneath it due to the appliance falling off 24 Use manual tools and equipment suitable for the intended use in particular make sure that the tool is not worn and that the handle is intact and fully fastened to the rest of the tool use them correctly and make sure they don t fall from a height Put them safely back in place after use Use electrical equipment su
11. f personal injury in some circumstances even fatal Failure to comply with this warning implies the risk of damage in some circumstances even serious to property plants or animals o Obligation to keep to the general safety norms and appliance specifications 23 Warning Risk Electrocution from live components Do not perform operations that involve opening Personal injury from burns due to overheated the appliance components or wounds caused by sharp edges or protrusions A A i i nents Do not perform operations that involve removing Electrocution from live components A the appliance from its place of installation Flooding due to water leaking from disconnected piping Do not start or stop the appliance by simply Electrocution from a damaged cable or plug plugging it into or out of the electricity mains or socket A Do not damage the power supply cable Electrocution from live unsheathed wires Al Personal injury from an object falling off the y appliance following vibrations Do not leave anything on top of the appliance Damage to the appliance or any objects underneath it due to the object falling off following vibrations from its place of installation Do not climb onto chairs stools ladders or Personal injury from falling from a height or from unstable supports to clean the appliance cuts stepladders shutting accidentally Do not attempt to clean the appliance without first turning it off an
12. gv z piros Tepl voda amp erven Woda goraca czerwony B Acqua fredda blu Kaltwasser blau Cold water blue Eau froide bleu Koudwater blauw Hidegv z k k Studen voda modr v Woda zimna niebieski 84 174 1 25 0 Fig 3 015 85 251 Fig 9 89 1 Regolatore di temperatura 2 Resistenza 3 Lampada spia 4 Limitatore di temperatura RESET SYSTEM 1 Temperaturregler 2 Heizk rper 3 Signallampe 4 Temperaturbegrenzer RESET SYSTEM 1 Temperature regulator 2 Heating element 3 Indicator lamp 4 Temperature limiter RESET SYSTEM 1 R gulateur de temp rature 2 R sistance 3 Lampe t moin 4 Limiteur de temp rature RESET SYSTEM 1 Temperatuurregelaar 2 Weerstand 3 Controlelampje 5 Temperatuurbegrenzer RESET SYSTEM 1 H m rs kletszab lyoz 2 F t test 3 Jelz l mpa 4 H merseklet hat rol RESET SYSTEM 1 Regulace teploty 2 Odpor 3 Kontroln z rovka 4 Havarijn termostat RESET SYSTEM 1 Regulator temperatury 2 Grzatka 3 Lampka kontrolna 4 Termostat ogranicznik temperatury
13. in werking zet moet men ervan overtuigd zijn dat de boiler vol water is Men moet om dat te bereiken de warmwaterkraan links openen en afwachten totdat geen water e meer uit de draan komt FIGYELEM A vizmelegit szabad kifolyasu Csak a gy rt ltal tartoz kk nt csomagolt szabadkifolyasu kever csappal lehet szerelni Miel tt a k sz l ket bekapcsolja gy z dj n meg arr l hogy a kesz l ket v zzel felt lt tt k nyissa ki a melegv zcsapot balra s varja meg am g v z folyik a csapb l UPOZORN N Oh va je beztlakovy Nen t eba odvzdus ovat je nutn ale pou vat baterie ur en pro beztlakov oh va e P ed uveden m oh va e do provozu je nutn ov it zda je napln n vodou otev t v tok tepl vody na lev stran a ekat a bude voda vyt kat bez vzduchov ch bublinek UWAGA Podgrzewacz o opr nianiu grawitacyjnym bezci nieniowy Opr nianie dzia a jak system odpowietrzania nale y zastosowa krany baterie jedynie te odpowiednie o podgrzewaczy o opr nianiu grawitacyjnym podgrzewaczy bezci nieniowych Przed w czeniem urz dzenia nale y upewni si czy jest ono nape nione wod w tym celu nale y otworzy kran ciep ej wody lewy i odczeka a do momentu gdy zacznie wylewa si woda CD Istruzioni per l installazione uso e la manutenzione pag 7 Installations und Gebrauchs und wartungs anweisungen pag 17 GB Instructions for installati
14. ing empty all components that may contain hot water carrying out any bleeding if Personal injury from burns necessary Descale the components in accordance with Personal injury due to contact of the skin or eyes the instructions provided on the safety data with acidic substances inhalation or swallowing sheet of the product used airing the room of harmful chemical agents wearing protective clothing avoid mixing different S products and protect the appliance and Damage to the appliance or surrounding objects surrounding objects due to corrosion caused by acidic substances 26 DESCRIPTION OF THE WATER HEATER see fig 4 A Pilot lamp B Control knob C Front cover TECHNICAL CHARACTERISTICS For the technical characteristics of the appliance please refer to the information provided on the data plate Date of Model manufacture Maximum working Capacity pressure Absorbed power Power supply voltage GE Current intensity Approvals Degree of protection Mains frequency against water Capacity 5 Power See data plate Voltage See data plate Mains water pressure 0 Weight 2 6 This appliance complies with the provisions set forth in the EEC 89 336 EMC directive on electromagnetic compatibility INSTALLATION NORMS for the installer WARNING Follow the general warnings and the safety norms listed at the beginning of the text and keep to all the instructions given under all circumstances
15. itable for the intended use in particular make sure that the power supply cable and plug are intact and that the parts featuring rotary or reciprocating motion are fastened correctly use this equipment correctly do not obstruct passageways with the power supply cable make sure no equipment could fall from a heignt Disconnect it and put it safely back in place after use Make sure any portable ladders are positioned securely and that they are suitably resistant and that the steps are intact and not slippery and do not slide around when someone climbs them and ensure someone supervises at all times Make sure any rolling ladders are positioned securely that they are suitably resistant that the steps are intact and not slippery that they are fitted with handrails on either side of the ladder and parapets on the landing During all work carried out at a certain height generally with a difference in height of more than two metres make sure that parapets are used to surround the works area or individual 7 harnesses designed to prevent falls and that the space covered during any accidental fall is free from dangerous obstacles and that any impact upon falling is cushioned by semi rigid or deformable surfaces Make sure the place of work has suitable hygiene and sanitary conditions in terms of lighting ventilation the solidity of the structures and emergency exits 19 During all work wear individual protective clothing
16. lues set the knob F fig 6 to setting The pilot lamp A fig 4 stays on during the heating phase MAINTENANCE REGULATIONS for competent persons WARNING Follow the general warnings and the safety norms listed at the beginning of the text and keep to all the instructions given under all circumstances 29 All maintenance operations and service visits should be performed by a competent person who have the skills required by the applicable norms in force Before performing any maintenance operations and or replacing any components disconnect the appliance from the electricity mains using the external switch empty out the water heater if necessary O See warning nos 20 26 28 Replacing parts when necessary To access the electrical parts heating element thermostat pilot lamp remove the cover C by unscrewing screws D fig 4 In the event of an intervention on the thermostat disconnect the latter from the electricity mains and slide it out of its seat on the heating element In the event of an intervention on the heating element unscrew the bolts A fig 6 using a 10 mm spanner When remounting the components make sure you put the flange seal the thermostat the heating element and all pipes back in their original position We recommend you replace the seal each time you dismount the flange Once the aforementioned operations are complete make sure you fill the appliance with water before powering it Periodic mainte
17. mage due to improper incorrect and unreasonable use or due to failure to comply with the instructions set forth herein 6 Installation maintenance and all other interventions must be carried out by a competent person in full conformity with the applicable legal regulations and the directions provided by the manufacturer 7 Incorrect installation can cause personal injury property damage and damage to animals the manufacturer will not be held responsible for such damage 8 Keep all packing material clips plastic bags polystyrene foam etc out of children s reach as they are hazardous 9 Itis strictly prohibited for children or inexperienced people to use the appliance 10 It is strictly forbidden to touch the appliance barefoot or with wet hands or feet 11 All repairs should be carried out by a competent person only using only original spare parts Failure to comply with the above instructions could compromise safety and invalidate all liability on the part of the manufacturer 12 The temperature of the hot water is adjusted by an operating thermostat that acts as a resettable safety device to avoid any dangerous rises in temperature 13 The appliance electrical connection should be made in accordance with the instructions provided in the relevant paragraph 14 No inflammable items should be left in the vicinity of the appliance GENERAL SAFETY NORMS Key to symbols Failure to comply with this warning implies the risk o
18. nance The following operations should be performed annually empty the appliance and dismount the heating element carefully remove all limescale from the heating element parts if you prefer not to use acids designed especially for this purpose use non metallic objects to break off the limescale crust that has formed taking care not to damage the heating element s armour We recommend you replace the seal each time you dismount the heating element To remount the heating element the tightening torque of the bolts A fig 6 should be between 7 and 10 N m You must respect the criss cross type of tightening Once the aforementioned operations are complete make sure you fill the appliance with water before powering it Resetting the bipolar safety In the event of an abnormal overheating of the water a thermal safety switch in compliance with CEI EN norms cuts off the electrical circuit on both the power supply phases of the heating element To reset the operation of the appliance proceed as follows leave it to cool set the knob F fig 6 to the maximum temperature position remove the cover C by unscrewing screws D fig 4 disconnect the thermostat T fig 6 from the electricity mains using a cross head screwdriver press on point A fig 9 until you hear it click Remount everything in the reverse order paying particular attention to repositioning the components correctly Once the aforementioned o
19. on use and maintenance pag 27 CF Intructions pour l installation emploi l entretien pag 37 Installatie en onderhoudsvoorschriften pag 47 Beszerel si haszn lati s karbantart si tmutat pag 57 N vod k obsluze pou it a instalaci pag 67 PD Instrukcja instalacji uzytkowania i obstugi str 77 GENERAL WARNINGS 1 This manual is an integral and essential part of the appliance It should be preserved with care alongside the appliance even if the latter is transferred to another owner or user and or moved to another location 2 Carefully read the instructions and warnings contained in this manual they provide important information for the safe installation use and maintenance of your new appliance 3 The installation is the responsibility of the buyer and should be performed by a competent person in accordance with the instructions contained herein 4 This is an open outlet water heater without pressure and can supply hot water for domestic use at one point of use only To this end it should be connected to the distribution mains for domestic hot water compatible with the appliance performance and power rating The hot water pipe should never be blocked or clogged if you wish to use mixer taps use those designed especially for open outlet water heaters 5 The use of this appliance for purposes other than those specified is strictly forbidden The manufacturer is not to be held responsible for any da
20. perations are complete make sure you fill the appliance with water before powering it USER INSTRUCTIONS WARNING Follow the general warnings and the safety norms listed at the beginning of the text and keep to all the instructions given under all circumstances 30 Advice for user Avoid positioning any objects and or appliances that could be damaged by water leaks beneath the water heater Should you not use any water for an extended period of time you should disconnect the appliance from the electrical supply by switching the external switch to OFF turn off the plumbing circuit taps Hot water at above 50 C flowing out of the taps at the point of use could cause serious scalds or even death from burns Children the disabled and the elderly are more exposed to the risk of burns It is strictly forbidden for the user to perform any routine or extraordinary maintenance Before calling the after sales service centre for assistance in the event of a suspected malfunction check first whether this is due to other causes such as for example a temporary power failure or water shortage See warning nos 1 2 3 See warning no 4 Contact a competent person for the replacement of the power supply cable O See warning nos 5 6 8 O See warning no 21 To clean the outer parts of the appliance use a damp cloth soaked in soapy water See warning no 21 To clean the outer parts of the appliance use a
21. ting pressure the temperature of the hot water that could at times reach well over 80 C We advise against the use of materials that cannot withstand such high temperatures We recommend you use dielectric joints for the electrical insulation of the appliance from the water mains Connect the inlet pipe marked with a blue rubber washer and the outlet pipe red rubber washer to the corresponding pipes of the system Tighten couplings E using a pair of spanners as illustrated in fig 4 In the event of low mains pressure values install the appliance at no more than one metre above the tap fig 3 and no more than 2 metres form the side of the latter Should these distances be greater than the recommended values you must include an air valve on the hot water pipe Fill the appliance up and let the water flow out of the tap for a few seconds The water flow rate with the tap turned on fully should not be more than 5 l min for this reason in accordance with DIN 44531 norm you should adjust the small valve fig 5 to limit the water flow In the presence of particularly hard waters there will be a considerable and rapid formation of limescale inside the appliance with a consequent loss in efficiency and damage to the electric heating element Electrical connection For greater safety have qualified personnel carry out a careful inspection of the electrical system ensuring it complies with the applicable norms in force because the appli
22. use the appliance use 25 Ref Warning Risk Symbol Make all electrical connections using conductors Fire due to overheating from electrical current with a suitable section passing through undersized cables Protect the appliance and all areas in the vicinity Damage to the appliance or surrounding objects of the work place using suitable material from falling splinters knocks and incisions Handle the appliance with suitable protection Damage to the appliance or surrounding objects and with care from shocks knocks incisions and squashing Organise the dislocation of all debris and D h i ding obj 27 equipment in such a way as to make movement f Sieg G Gok ind or iat Ing ol d easy and safe avoiding any piles that could yield from shocks knocks incisions and squashing or collapse Reset all the safety and control functions affected by any interventions performed on the appliance Damage or shutdown of the appliance due to and make sure they operate correctly before out of control operation re using the appliance SPECIFIC SAFETY NORMS FOR THIS APPLIANCE Key to symbols Symbol SS Failure to comply with this warning implies the risk of personal injury in some circumstances even fatal Failure to comply with this warning implies the risk of damage in some circumstances even serious to property plants or animals o Obligation to keep to the general safety norms and appliance specifications Before handl
Download Pdf Manuals
Related Search