Installation Instructions
Contents
1. INSTALLATION FAIRING SPEARS with L E D ACCENT LIGHT GL 1800 7337 PARTS INCLUDED 1 Left Fairing Spear with L E D Accent 1 Right Fairing Spear with L E D Accent 1 Hardware Kit Containing 2 Alcohol Pads 2 Y Adapter Plugs 5 1 4 Long 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY ATTENTION This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality CAUTION This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage TOOLS SUGGESTED Phillips screwdriver Center Punch Set of Metric Hex Wrenches STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition NOTE 06 to 10 models that do n2. less than 50 F LEAN T D TUE IF ZE STEP 4 Rub the backing on the adhesive strip to activate the adhesive before applying f Remove the adhesive backing Press the Fairing Spear to the left side of the fairing into place for 1 minute to ensure proper adhesion Full bond strength will occur within 24 hours PIC 1 Repeat for right side NOTE If the bike be will ridden before the Fairing Spears have been installed for 24 hours Kuryakyn recommends that you use masking tape over the Fairing Spears to ensure proper adhesion STEP 5 Locate the rubber boot at the base of each mirror Carefully peel this boot back away from the fairing to expose the wire connections Pay attention to how the boot joins with the fairing this will aid in replacing the boot in its proper position during reassembly PIC 3 STEP 6 Carefully remove the trim molding from each side as shown in PIC 4 The upper edge has a tab that fits into a slot under the fairing PIC 5 You may find it helpful to start removing the trim at the bottom and work your way to the upper edge STEP 7 Remove the side compartments Use a center punch to depress the locking mechanism in each of the plastic fasteners PIC 6 The right side compartment sitting on the bike needs to be opened with a key then remove two Phillips head screws and two of the locking plastic fasteners STEP 8 Thread the connector end of the wire harness under the front of the fairing above the inside fairing vent
3. orcycle running test the Fairing Light running lights and turn signal f ie LERON for proper operation ENSURE PROPER RUNNING LIGHT AND TURN SIGNAL OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS RUNNING LIGHT OR TURN SIGNAL MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY Tuck any excess wire harness behind the mirror joint Roll the rubber boot back into position against the base of each mirror heat Kuryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abraded melted or frayed wires Replace each side compartment To engage the plastic fasteners first be sure the locking mechanism is in the raised position as shown in PIC 11 Place a fastener in each hole then press straight down on the locking mechanism to engage av s e Replace each trim molding Fit the lip at the top of the molding into the slot under the fairing then carefully snap the length of the molding into place THREAD WIRE season THROUGH POCKET LIKE THIS 7 PAGE s amp a 3 Ride On L E D FAIRING SPEARS INSTALLATION
4. ot have existing Kuryakyn front accent lighting require P N 7300 Adapter Plug purchased separately for Plug and Play wiring ATTENTION A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all steps in the procedure consult a trained technician STEP 2 Remove any grease or debris from both sides of the outer fairing with soapy water and a clean rag rinse and allow the area to dry completely PIC 1 Clean the area with the included alcohol cleaning pad to remove any residue allow the area to dry completely 7337 21GL 0711 POALE cont CUSTOMER SERVICE INSTALLATION QUESTIONS LIMITED WARRANTY ABOUT OUR CATALOG ee ATTENTION Thoroughly clean the area of grease oil dirt or other debris to ensure Kuryakyn proper adhesion Kuryakyn WILL NOT warranty any parts lost due to improper installation STEP 3 Test fit the left Fairing Spear to the fairing They will install just above the body line groove not in the channel Make any reference marks with a non permanent marker or masking tape PIC 1 as a starting point the rear of the L E D Fairing Spear will be about 1 1 4 above the deepest part of the body groove h t L ATTENTION The adhesive may not correctly bond if applied at temperatures less than r 7 maaa O 50 F Do not attempt this installation in temperatures
5. to behind the fairing up to the mirror joint a piece of stiff wire or a straightened coat hanger with the connector of the wire harness taped to it may ease threading this through the fairing PIC 7 and PIC 8 START AT THE BOTTOM AND WORK ATTENTION Secure all wiring away from any m TO THE TOP moving parts pinch points or P extreme heat K ryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abraded melted or frayed wires cont L E D FAIRING SPEARS INSTALLATION ATTENTION Kiiryakyn recommends the use of dielectric grease on electrical connections Kuryakyn STEP 9 NOTE If you have already installed additional Kuryakyn accessory lights on the STEP 10 WARNING STEP 11 ATTENTION Secure all wiring away from any moving parts pinch points or extreme STEP 12 STEP 13 For O6 up models with P N 7300 adapter Apply dielectric grease to all the electrical connections Connect the adapter to the wire harness then to the turn signal harness For all other models Apply dielectric grease to all the electrical connections Connect the Y connector to the wire harness then to the turn signal harness front of the bike and you do not have an extra plug in you may use Kuryakyn P N 7302 Multi Plug and Play Connector with the existing Kuryakyn wire adapter for additional plug ins in place of the included wire adapter w if With the mot
Download Pdf Manuals
Related Search