Home

Installation and Operations Guide PDF

1. VS5008 Series Sequential Switcher Installation Operation Manual C809M E 12 99 CE Pelco 300 W Pontiac Way Clovis CA 93612 5699 USA Pelco Online 9 http www pelco com In North America and Canada Tel 800 289 9100 or FAX 800 289 9150 DataFAX 800 289 9108 International Customers Tel 1 559 292 1981 or FAX 1 559 348 1120 DataFAX 1 559 292 0435 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product the following WARNINGS should be observed 1 Installation and servicing should only be done by qualified service personnel and con form to all local codes 2 Unless the unit is specifically marked as a NEMA Type 3 3R 3S 4 4X 6 or 6P enclo sure it is designed for indoor use only and it must not be installed where exposed to rain and moisture 3 Only use replacement parts recommended by Pelco 4 After replacement repair of this unit s electrical components conduct a resistance measurement between line and exposed parts to verify the exposed parts have not been connected to line circuitry The product and or manual may bear the following marks This symbol indicates that dangerous volt age constituting a risk of electric shock is present within this unit CAUTION RISK OF ELECTRIC SHOCK This symbol indicates that there are impor DO NOT OPEN tant operating and maintenance instructions in the literature accompanying this unit Please thoroughly familiari
2. NORMALLY OPEN SWITCH EACH ALARM DEVICE MUST BE CONNECTED TO THE COM TERMINAL UP TO EIGHT VIDEO INPUTS CAMERAS we wet n c o wer rezas ore Llanos Ec LL VS5008 REAR OPEN COLLECTOR OUTPUT FOR VCR ACTIVATION IN ALARM CONDITION ONLY ONE VCR CAN BE USED IN THIS CONFIGURATION Figure 2 Alarm Hook up Pelco Manual C809M E 12 99 06 06603040 DE NOTE MON 1 must be terminated COM ALARM Coeur 7 14 elelelelalelsleis e 1283452678 ALARM OUT VS5008 REAR Figure 3 Terminating Configuration One Monitor NOTE In this configura tion MON 1 must be terminated and the unit must be modified in order to be looping refer to Figure 1 VS5008 REAR VIDEO INPUTS ADDITIONAL EQUIPMENT TERMINATED Figure 4 Looping Configuration One Monitor 4 Pelco Manual C809M E 12 99 12S 435 8 7 E ALARM OUT S 7 VS5008 REAR Figure 5 Terminating Configuration Two Monitors NOTE In this configuration the unit must be modified in order to be looping refer to Figure 1 VS5008 REAR VIDEO INPUTS L IL L1 1 d d d ADDI
3. TIONAL EQUIPMENT TERMINATED Figure 6 Looping Configuration Two Monitors Pelco Manual C809M E 12 99 COAXITRON RECEIVER INPUT 12345678 ALARM QUT VS5008 REAR LOOPING INPUT FROM OUTPUTTO OUTPUT RECEIVER MONITOR J8 J7 J6 COAXITRON TRANSMITTER REAR NOTE IN THIS CONFIGURATION THE LOOPING OUTPUT J8 IS UNTERMINATED Figure 7 VS5008 with a Coaxitron Transmitter OPERATION ONE MONITOR OPERATION When the VS5008 is configured for one monitor operation the monitor must be connected to the MON 2 output The eight video inputs will automatically sequence through the moni tor To remove a channel from the sequence set the channel s switch to BYPASS Switching any channel to the MONITOR position will interrupt the sequence and display input from the selected channel onto the monitor TWO MONITOR OPERATION When configured for two monitor operation the eight video inputs will automatically se quence through Monitor 1 To remove a channel from the sequence set the channel s switch to BYPASS To view a single channel set the channel s switch to the MONITOR position Monitor 2 displays the output Monitor 2 s output will not interfere with Monitor 1 s sequenc ing If all switches are set to the AUTO position Monitor 2 sequences with Monitor 1 If more than one channel switch is set to the MONITOR position the lowest number switch takes pre
4. cedence ALARM OPERATION Set the ALARM switch to the ON position If all the channel switches on the front panel are set to AUTO when an alarm occurs both monitors immediately switch to the alarmed channel and the associated LED blinks If more than one alarm is triggered the monitors sequence simultaneously at a three second rate between the alarmed channels Pelco Manual C809M E 12 99 If a channel is set to the MONITOR position Monitor 1 switches to the alarmed channel but Monitor 2 continues to display the selected channel If a channel is set to BYPASS Monitor 1 switches to the alarmed channel Once an alarm is triggered the alarm remains on until the alarm condition is removed or the alarm switch is moved to the OFF position When the alarm switch is in the OFF position the switcher ignores any alarm inputs SERVICE MANUAL If you need to service your unit obtain a service manual in one of the following ways Go to Pelco s web site at ftp www pelco com and find service manual C809SM Call Pelco s DataFAX service at 1 800 289 9108 or 1 559 292 0435 and request docu ment 28098 Contact Pelco s Literature Department and request service manual C809SM SPECIFICATIONS VIDEO Inputs Terminating 75 ohms or looping Outputs Monitor 1 2 75 ohms Monitor X Coaxitron transmitter non amplified output Gain Unity Dwell Adjustable from 1 70 seconds nominal Frequency Response Flat within 1 dB to 10 MHz Maximu
5. d of return shipment shall be the same or equal to the method by which the item was received by Pelco RETURNS In order to expedite parts returned to the factory for repair or credit please call the factory at 800 289 9100 or 559 292 1981 to obtain an authoriza tion number CA number if returned for credit and RA number if returned for repair Goods returned for repair or credit should be clearly identified with the assigned CA RA number and freight should be prepaid All merchandise returned for credit may be subject to a 20 restocking and refurbishing charge Ship freight prepaid to Pelco 300 West Pontiac Way Clovis CA 93612 5699 REVISION HISTORY Manual Date C809M 9 92 Comments Rev D C809M E 12 99 Moved exploded assembly diagram parts list and schematic to new maintenance service manual C809SM Updated manual to new format Copyright 1999 Pelco All rights reserved Pelco the Pelco logo Spectra Genex Legacy Coaxitron and Intercept are registered trademarks of Pelco Esprit is a trademark of Pelco 8 Pelco Manual C809M E 12 99
6. m Signal Level 2 Vp p Tilt 296 Crosstalk Better than 40 dB at 5 5 MHz ELECTRICAL Power Requirements for Transformer 1 5 vA 125 amp at 12 volts RMS 15 50 60 Hz from a dedicated isolated power supply Wall transformer provided with unit 120 or 230 VAC operation Connectors BNC Alarm In Normally open relay contact 10V at 1 mA Alarm Out Open collector GENERAL Construction Chassis Steel zinc plated Cover Steel black polyester powder coat Panel Aluminum black polyester powder coat with white silk screen Environment 32 to 120 F 0 to 49 C Dimensions 1 75 H x 14 50 W x 8 50 D inches 4 45 x 36 83 x 21 59 cm Weight 7 Ib 3 17 kg RATINGS NEMA 1 Design and product specifications subject to change without notice Pelco Manual C809M E 12 99 7 REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital de vice pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment gener ates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications How ever there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be de
7. r to Figure 2 for connections b Output Connections The VS5008 can activate an external device such as a VCR during an alarm response Refer to Figure 2 for connections The output load must not exceed 40 mA Typical connections to this output would be active low logic input devices solid state relays or optical couplers Make all equipment connections to the VS5008 If the system configuration utilizes only one monitor the monitor must be connected to the MON 2 output to allow se quencing or to display an individual channel Refer to Figures 3 through 6 for system configurations If you are using the VS5008 with a Coaxitron transmitter model MPT9000CZ or MPT9000P2Z follow the configuration shown in Figure 7 Set all channel switches to AUTO center If a video input is not connected set the corresponding channel switch to the BYPASS down position Connect the AC adapter to the 12 VAC input socket on the switcher Connect the trans former to a 120 or 230 VAC power supply The switcher starts sequencing Use a screwdriver to adjust the DWELL interval control to the desired switching inter val 1 to 70 seconds nominal Rotate the DWELL control clockwise for longer intervals and counterclockwise for shorter intervals This control is a 15 turn precision potenti ometer The approximate ratio is one full turn per 4 to 5 seconds of delay UP TO EIGHT ALARM INPUTS ALARM INPUT FROM MOTION DETECTOR DOOR CONTACT ETC THROUGH
8. se alteration normal wear or accident are not covered under this war ranty Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products Pelco s liability for any claim whether based on breach of contract negligence in fringement of any rights of any party or product liability relating to the Prod ucts shall not exceed the price paid by the Dealer to Pelco for such Products In no event will Pelco be liable for any special incidental or consequential damages including loss of use loss of profit and claims of third parties how ever caused whether by the negligence of Pelco or otherwise The above warranty provides the Dealer with specific legal rights The Dealer may also have additional rights which are subject to variation from state to state If a warranty repair is required the Dealer must contact Pelco at 800 289 9100 or 559 292 1981 to obtain a Repair Authorization number RA and provide the following information 1 Model and serial number 2 Date of shipment P O number Sales Order number or Pelco invoice number 3 Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above please include a written expla nation with the product when returned Ship freight prepaid to Pelco 300 West Pontiac Way Clovis CA 93612 5699 Metho
9. termined by turning the equipment off and on the user is encouraged to try and cor rect the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the re ceiver is connected Consult the dealer or an experienced radio TV technician for help WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace without charge any merchandise proved defec tive in material or workmanship for a period of one year after the date of shipment Exceptions to this warranty are as noted below Three years on Genex Series multiplexers server and keyboard Two years on all standard motorized and fixed focal length lenses Two years on Esprit Legacy Intercept PV1000 Series CM6700 CM8500 CM9500 CM9750 CM9760 Matrix Spectra DF5 Series and DF8 Fixed Dome products Two years on WW5700 series window wiper excluding wiper blades Two years on cameras Six months on all pan and tilts scanners or preset lenses used in continuous motion applications that is preset scan tour and auto scan modes Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment All goods requiring warranty repair shall be sent freight prepaid to Pelco Clovis California Repairs made necessary by reason of misu
10. ze yourself with the information in this manual prior to installation and operation DESCRIPTION The VS5008 is a sequential switcher designed to switch up to eight cameras manually or automatically to one or two monitors and to respond automatically to alarm inputs MODELS VS5008 Sequential switcher eight camera inputs two monitor outputs Coaxitron compatible desktop or rack mount 120 VAC UL VS5008 220 Same as VS5008 except 230 VAC CE INSTALLATION 1 The VS5008 Series Sequential Switcher is shipped as a terminating unit but can be modified for looping operation To install the VS5008 do the following a Terminating Operation Proceed to step 2 b Looping Operation To convert to looping operation remove the cover Remove the rear panel of the chassis Locate the 75 ohm resistors at the rear of the BNC jacks Use wire cutters to clip one of the resistor leads for each input that you want to loop refer to Figure 1 Replace the cover Looping and terminating in puts may be mixed 75 OHM RESISTOR K CLIP AY l BNC CONNECTOR Figure 1 Looping Conversion Modification Pelco Manual C809M E 12 99 NOTE MON 1 output must be terminated at all times with a monitor or if not used by a 75 ohm BNC terminator Place the switcher on a desktop or install it in an equipment rack Make alarm connections a Input Connections The VS5008 has eight alarm inputs that require a ground to activate Refe

Installation and Operations Guide PDF

Contents

Download Pdf Manuals

Related Search

Related Contents