L.E.D. HALO TRIM RING For 5
Contents
1. PIC 4 NOTE If the headlight feels loose or rattles when assembled disassemble the headlight and attach the included Adhesive Backed Foam Tape to the backing plate so it presses against the back of the headlight PIC 5 ATTENTION It is the installer s responsibility to ensure that all of the fasteners including pre assembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required STEP 4 Install one of the included male spades to the end of the RED and to the end of the BLACK wires coming from the L E D Halo Light Route the wire harness from the L E D Halo light below the headlight and along the headlight wire harness STEP 5 Remove the seat 8 32 X 1 SCREW PIC 5 STEP 6 Plug the extension harness into the leads from the Halo Light Red wire to Red wire Black wire to Black wire FOAM TAPE GOES AGAINST HEADLIGHT NOTE Wrap each connection with electrical tape to help prevent shorting out ATTENTION Kiiryakyn recommends the use of dielectric grease on electrical connections cont L E D HALO TRIM RING INSTALLATION STEP 7 CAUTION STEP 8 STEP 9 STEP 10 ATTENTION Secure all wiring away from any moving parts pinch STEP 11 WARNING Kuryakyn Vy f ig Loosen the front tank bolts and remove the rear tank bolt to allow you to raise the rear of the tank PIC 6 and PIC 7 Rou2. Wrenches STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE ABOUT OUR CATALOG PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS ithasino ire ine products you STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition WARNING YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY 7270 21HD 0212 cont Kuryakyn CAUTION Avoid damage to the motorcycle Protect painted surfaces with a soft cloth or blanket ATTENTION A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all of the steps in the procedure consult a trained technician a STEP 2 Remove the screw from the bottom of the headlight trim ring and remove the trim ring PIC 1 Set the trim ring aside it will not be reused STEP 3 Install the new Halo Trim Ring to the headlight by inserting the cutouts on the Trim Ring over the tabs on the headlight housing PIC 2 then turning the Trim ring clockwise until the screw tabs are in line PIC 3 STEP 4 Secure the Trim Ring to the headlight housing using the included 8 32 X 1 Self Tapping Screw The L E D Halo Light Ring will seat next to the front of the Trim Ring
3. INSTALLATION L E D HALO TRIM RING for 5 3 4 LIGHTS 7270 PARTS INCLUDED CUSTOMER SERVICE Chrome Halo Trim Ring with Bottom Tab L E D Halo Light Ring INSTALLATION QUESTIONS 8 32 X 1 Self Tapping Screw A r call 715 47 J087 Wire Harness Wiring Kit Containing LIMITED WARRANTY 4 Black Nylon Cable Ties E Ly MAR Female T Tap Connectors Insulated Female Spade Connectors NOT USED Male Spade Connectors Adhesive Foam Strips e Kuryakyn s l Dielectric Grease Pack nstallation Instructions el el ee a ew BR BR W 1 eH Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN eK ryal IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR eK ryakyn sh PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL i EUAN A INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING eK ryakyn products are THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY ATTENTION This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality CAUTION This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage TOOLS SUGGESTED Phillips Screwdriver Flat Blade Screwdriver Set of Combination
4. nect the battery Test the L E D Halo Light for proper operation Reinstall the seat ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY PAGE Ride On 3 L E D HALO TRIM RING INSTALLATION
5. te the extension harness under the tank and along the main harness to the battery When raising the fuel tank care MUST be taken not to stretch puncture or break the attached fuel line a at can J ge a z LOOSEN FRONT FASTENER NA Using a test light or the wiring schematic for your bike turn the key ON and locate a keyed 12 volt power wire one that gets power when the key is turned on and loses power when the key is turned off and a ground wire in the bike harness under the seat Turn the key OFF and disconnect the battery Install one of the included Female T Tap connectors to each wire PIC 8 g si t ge ele Ti fi Y f Hi E 4 REMOVE REAR FASTENE An gt s s EE es J Tr ee Mine D Install one of the included Male Spade connectors to the RED wire in the extension ral harness and plug it into the Female T Tap on the keyed power wire PIC 8 I Install one of the included Male Spade connectors to the BLACK wire in the Sit extension harness and plug it into the Female T Tap on the ground wire PIC 8 Using the included Nylon Cable Ties secure the extension harness out of the way of excessive heat and pinch points Install the rear tank bolt Tighten this and the front tank bolts securely points or extreme heat Kuryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abraded melted or frayed wires Recon
Download Pdf Manuals
Related Search