46770, 46880 - Ford 5.0L Coyote Crate Engine_120320.indd
Contents
1. 25 Clutch Bolt Pattern 6 Bolt 10 5 11 5 Starter Ring Gear Tooth 164 177 lb in Plus additional 60 35 ft lbs Plus additional 60 ACT Harness 2013 Edelbrock LLC Brochure 63 46770 Supercharger Intercooler Routing Diagram Or LS ERA J s a r L NATA k MENNY LTR Plumbing Intercooler Oo Not Included Reservoir Tank gt L g ait 7 Y Y gt E E N Electric Water Pump Low Temp Radiator LTR Not Included Edelbrock LLC 2700 California St Torrance CA 90503 Tech Line 1 800 416 8628 Office Line 310 781 2222 Part 4 46770 46880 2013 Edelbrock LLC Rev 3 20 13 QT mc Page 3 Brochure 63 467702. EDELBROCK CRATE ENGINE SUPERCHARGED FORD 5 0L COYOTE Part 46770 46880 GENERAL INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation If you have any questions please call our Technical Hotline at 1 800 416 8628 7 00 AM 5 00 PM Pacific Standard Time Monday through Friday Proper installation ts the responsibility of the installer Improper installation will void the manufacturer s warranty and may result in poor performance and engine or vehicle damage IMPORTANT NOTE This instruction sheet provides general installation guidelines which can affect your warranty Read it carefully It is not our intent to cover each detail of installation here as the procedures are vehicle specific We want to caution you that installing an engine is a complicated procedure that requires a good general knowledge of automotive mechanics It is a good idea to refer to the factory service manual for your vehicle If you are not confident that you can complete the engine installation successfully we suggest you consider having it installed by an experienced mechanic CAUTION This engine is NOT INTENDED for marine use Not legal for use in pollution controlled vehicles DESCRIPTION This crate engine is built using a Ford aluminum 5 0L block with a forged and balanced crankshaft forged Manley H Beam connecting rods and Mahle forged aluminum pistons which are then combined with Edelbrock s E Force Superc
3. can occur if fuel flow is insufficient Part 46770 46880 Rev 3 20 13 QT mc Page 1 e Fuel Pressure Regulator with Boost Reference GENERAL SUPERCHARGER PLUMBING INSTALLATION Determine the ideal mounting location for the intercooler heat exchanger not included It is important that the heat exchanger receives the coldest air possible which means mounting it in front of the radiator A C condenser and any oil or trans cooler the vehicle might have equipped Determine the ideal mounting location for the water pump A universal mounting bracket has been supplied to simplify installation Please note that the pump should be mounted no higher than the inlet of the heat exchanger The inlet of the pump is in line with the axis of the pump motor while the outlet extends out perpendicularly from the pump body Determine the ideal mounting location for the intercooler reservoir tank To simplify installation a universal mounting bracket and a groove around the perimeter of the tank for use with a large worm clamp have been included NOTE Be sure to mount the tank as high as possible to prevent air bubbles from accumulating in the cooling system Refer to the diagram on Page 3 for the suggested intercooler plumbing not included Note that the intercooler routing can be inverted so that the pump and tank are mounted on the driver side Regardless of component mounting locations it is important that the correct direction
4. harger to produce 700 horsepower and 606 ft lbs of torque on 91 octane pump gas Its compact design allows for a seamless swap into most platforms eliminating the need for modifications to your engine bay or hood AVAILABLE VARIANTS P N 46770 Supercharged Ford 5 0L Crate Engine Complete With Electronics P N 46880 Supercharged Ford 5 0L Crate Engine Complete Without Electronics PRODUCT SPECIFICATIONS Displacement 4 957L 302 ci Bore Stroke 3 629 bore 3 649 stroke Horsepower 700 Torque 606 Compression 9 5 1 Block New Ford Aluminum Cylinder Heads Factory Aluminum 54 5 57 5cc Supercharger Edelbrock E Force Pistons Mahle Forged Aluminum Crankshaft Forged 4340 Camshaft Duration Intake 260 Exhaust 263 Camshaft Lift Intake 12mm Exhaust 11mm Rocker Arms 2 1 ratio Spark Plugs Ford M 12405 M50 032 Gap Fuel Type Requires 91 Octane At All Times Firing Order 1 5 4 8 6 3 7 2 Maximum Rated RPM 7200 RPM Warranty 2 Year Unlimited Mileage ANCILLARY PARTS REQUIRED FOR INSTALLATION e Low Temperature Radiator LTR 15405 Full Face Universal Fit 15406 Compact Universal Fit 15407 Compact 16 x 16 Universal Fit e LTR Intercooler Plumbing e Fuel Pump A minimum fuel flow of 75gph Y 60psi differential pressure is required t is the responsibility of the customer to ensure that adequate fuel flow is achieved at the operating voltage of the fuel pump Engine damage
5. of flow is maintained GENERAL HARNESS INSTALLATION Determine the ideal mounting location for the relay and fuse holder on the water pump harness Connect the POSITIVE lead to a CONSTANT 12V power source Connect the GROUND lead to a chassis ground Connect the water pump connector to the electric water pump Connect the factory female EVAP connector to the male EVAP connector on the water pump harness Then plug the female end of the water pump harness onto the EVAP solenoid Install the ACT Harness to the ACT sensor on the rear of the supercharger manifold The female MAF adaptor connects to the 2013 Edelbrock LLC Brochure 63 46770 factory male MAF connector The male MAF connector connects to the factory MAF sensor f using the Ford Racing Electronic Throttle Crate Engine Controls Pack 46770 Only please refer to the installation instructions included with the controls pack for installation guidelines ENGINE OIL This crate engine is shipped dry without engine oil Make sure to add the recommended Ford oil prior to priming the engine oil The engine oil must be changed no more than 300 miles after break in A full synthetic SAE 5W 50 is highly recommended after the break in period Engine oil capacity is eight 8 quarts START UP The engine should be primed with oil prior to starting Install an oil pressure gauge to the existing oil pressure sensor Remove the spark plugs and disconnect the engine control
6. unit as well as the injector wires NOTE Make sure ignition and fuel are not provided to the engine Once fuel and spark have been disabled crank the engine using the starter for 10 seconds checking the oil gauge for oil pressure If no pressure is indicated wait 30 seconds and crank again for 10 seconds Repeat this process until oil pressure is indicated on the gauge Reconnect the engine control unit injector wires and reinstall spark plugs Start the engine and listen for any uncommon sounds If uncommon sounds are not present run the engine at idle until it reaches operational temperatures OIL PAN CLEARANCE Make sure you have adequate subframe and ground clearance before installing the engine FLYWHEELS AND FLEXPLATES The 5 0L Coyote engines use special flexplates or flywheels included See below Flywheel Torque Spec Clutch Torque Spec Harness Layout Water Pump Relay EVAP CL SS Solenoid EEN aN N W 5 Power Part 46770 46880 Rev 3 20 13 QT mc Page 2 Supply Wire ACT Sensor Water Pump Harness Engine Harness EVAP Connector Engine Harness MAF Connector MAF Sensor Flexplate Ford Part Number BL3Z6375A OEM Converter Bolt Pattern 8 Bolt 11 5 Outside Diameter 14 25 Starter Ring Gear Tooth 164 Torque Spec 177 lb in Plus additional 60 Flywheel Ford Part Number BR3Z6375D OEM Flywheel Bolt Pattern 8 Bolt Outside Diameter 14
Download Pdf Manuals
Related Search