GENUINE PARTS INSTALLATION INSTRUCTIONS
Contents
1. A Tie wrap L 150mm Fig22 b Main Harness aes d K basii Q ge j l a Accessory Engine Room Harness ae Connect Terminal Hood lock cable Fig22 c Tie Wrap L 150mm Accessory _Main Harness B PKB switch connector Connect Page 12 of 13 INSIDE WIRING HARNESS INSTALLATION 27 Accessory Harness connection Connect plug on the Accessory Main Harness to the Accessory Engine Harness as shown in Fig 22 a 28 Accessory Main Harness installation Route Accessory Main Harness along the vehicle harness to PKB switch as shown in Fig 22 a b c Disconnect PKB switch connector Connect connector of Accessory Main Harness to PKB switch connector and vehicle side connector as shown in Fig 22 C 29 Secure Accessory Engine Room Harness Secure the Accessory Main Harness with Tie Wrap 3 places L 150mm as shown in Fig 22 b c CAUTION Wrap tape around terminal plug connection for protection Do not allow harness to contact moving parts or vehicle edge 30 Reinstall vehicle parts B66M0 1AA0B II Rev 10 22 2013 CHECK AFTER INSTALLATION 1 Please check that the installation has no problem a Confirm connection of connector is secure b Confirm whether wire harness Is fixed c Confirm no part moving which will cause rattling noise d Confirm harness is protected from damage by sharp bracket edges OOOO FUNCTION CHECK C 1 Re connect battery negative terminal C2. Control Unit Lamp Module LH SONNALLOK Lamp Module RH Fig14 Male Terminal Female Terminal 8 pin connector IPDM module I Accessory Engine Room Hood lock cable Head lamp LH Page 8 of 13 WIRING HARNESS INSTALLATION OUTSIDE WIRING HARNESS INSTALLATION 16 Connect the Accessory Engine Room Harness LH RH to Control Unit Harness LH RH 17 Secure the Accessory Engine Room Harness to the vehicle harness with Tie Wraps 4 places L 150mm Shown in Fig13 44 CAUTION Do not allow harness to contact moving parts or vehicle edge 18 Accessory Engine Room Harness installation Inside engine room a Route 2 pin connector line along the vehicle harness to head lamp LH rear side as shown in Fig 14 b Route 8 pin connector and Female Terminal along the vehicle harness to IPDM module as shown in Fig 14 c Route Male Terminal along the hood lock cable to inside of front fender LH as shown in Fig 14 B66M0 1AA0B II Rev 10 22 2013 INSTALLATION PROCEDURE Pre Lt Lhe Ss er TT Accessory Engine Room Harness Head lamp LH D J i Front fender seal front LH Tie Wrap L 150mm ENG IS N Front side marker lamp connector Front side marker lamp harness 8 pin connector Fig15 d Female terminal a cl Za Connector loc ao s SSS ANS i Accessory Engine Room Harness terminal
3. 2 Confirm daytime driving light is on when ignition switch is on and parking brake off 3 Confirm daytime driving light is off when position lamp on REI NSTALLATI ON OF REMOVED PARTS C 1 All removed vehicle parts have been reinstalled CAUTION Use caution when re installing vehicle parts to avoid damage scratch or breaking of mounting clips C 2 Clean interior of vehicle VEHI CLE CHECK C 1 Remove all tools from the vehicle C 2 Inspect reinstalled vehicle parts for proper panel fit 3 Turn ignition to ON position C 4 Reset radio presets to the recorded setting C 5 Confirm proper radio operation 6 Initialize sun roof and power window operation C 7 Turn ignition to off position 4 CAUTION During reinstallation please use caution so as not to cause the stacking or pinching of the vehicle harness or damage of parts Page 13 of 13 B66M0 1AAO0B II Rev 10 22 2013
4. 4 Use seat and floor protection 5 Open the hood of the vehicle 7 This part is to be installed at a vehicle body surface temperature of 65 100 F 6 Disconnect the negative battery terminal to prevent short circuits during installation 8 Do not wash the vehicle for 24 hours after installing to prevent the double sided tape from peeling A CAUTION Care must be taken not to scratch or damage any components during the removal or replacement process 9 Remove the following vehicle parts in the sequence shown below Page 2 of 13 1 Radiator core support cover LH RH 2 Front bumper grille 3 Headlamp extension panel LH RH 4 Splash guard LH 5 Fender protector LH 6 1PDM module cover 7 1PDM module cover FR 8 Wheel and tire LH 9 Instrument side finisher LH 10 Instrument lower panel driver 11 Front kicking LH 12 Dashboard Side Lower panel LH 13 Fuse box B66M0 1AA0B II Rev 10 22 2013 INSTALLATION OVERVIEW 2 eS U a STANDARD CONNECTION METHOD Side marker LH hamess RKO2FGY ILL O 5 L GND 0 5 B RVO2MGY Side marker LH IPDM TENY B 0 5 R B Y TH20FW C512 NSOSMW X phere IGN 0 5 F Connector of vehicle IPDM Control 4 J Parking brake 7 8 i Unit PO1FB 1AA fila PKB 0 5 G POIMB Connector of Parking brake Page 3 of 13 B66M0 1AA0B II Rev 10 22 2013 INSTALLATION PROCEDURE Radiator core support Fender protecter LH Splash guard LH VEHICL
5. Connector is view from harness side Page 9 of 13 19 Accessory Engine Room Harness connection b C Pull back Front fender seal front LH Disconnect front side marker lamp LH connector Connect 2 pin connector of Accessory Engine Room Harness to front side marker lamp LH and vehicle side connector Secure the Accessory Engine Room Harness with Tie Wrap 1 place L 150mm as shown in Fig 15 a Disconnect IPDM module connector TH20FW CS12 M4 1V using lever and then partially disengage connector lock as shown in Fig 15 c Insert terminal from Accessory Engine Room Harness into connector of power supply harness as shown in Fig 15 b c d and then engage connector lock Disconnect IPDM module connector Connect 8 pin connector of Accessory Engine Room Harness to IPDM module and vehicle side connector Shown in Fig15 d B66M0 1AA0B II Rev 10 22 2013 INSTALLATION PROCEDURE Tie Wrap L 150mm Accessory Engine Room Hood lock cable Accessory Engine Room Harness 20 Secure Accessory Engine Room Harness Secure the Accessory Engine Room Harness to the vehicle harness with Tie Wraps L 150mm 6 places as shown in Fig 16 44 CAUTION Do not secure hood lock wire Do not allow harness to contact moving parts or vehicle edge 21 Accessory Engine Room Harness installation a Route male terminal along the hood lock cable to grommet as shown in Fig 17 b Pierce a pin hole through
6. E PARTS REMOVAL 1 Radiator core support cover LH RH removal Disengage the clips 15 places and then remove the Radiator core support cover LH RH 2 Front bmpr grille removal Disengage the clips 6 places and then remove the Front bumper grille Shown in Fig 1 3 Headlamp extension panel LH RH removal Remove the screws RH and LH connecting the front surface of bumper Remove the Headlamp extension panel LH RH Shown in Fig 2 4 Wheel LH removal Remove the wheel LH from the vehicle Shown in Fig 3 Fig 3 Fig 4 5 Splash guard LH removal Remove the clips 4 places connecting the splash guard LH 6 Fender protector LH removal Remove the screws 9 places and clips 4 places connecting the fender protector LH Shown in Fig 4 Page 4 of 13 B66M0 1AAO0B II Rev 10 22 2013 INSTALLATION PROCEDURE 7 IPDM module cover removal Push pawls and lift up the rear side of IPDM module cover IPDM module cover 8 IPDM module cover FR removal Push pawls and lift up the IPDM module cover Shown in Fig 5 9 Instrument side finisher LH removal Detach Instrument Side Finisher LH mounting clips with nylon removal tool and remove Instrument Side Finisher LH Shown in Fig 6 removal tool 10 Instrument lower panel driver removal a Remove hood opener mounting screw then remove hood opener b Pull downward on instrument lower panel LH to disengage pawls and clips c Disco
7. GENUINE PARTS kb z F INSTALLATION INSTRUCTIONS DESCRIPTION LED Daytime Driving Lights APPLICATION MURANO MURANO CROSS CABRIOLET PART NUMBER LED Daytime Driving Lights B66M0 1AAOB KIT CONTENTS Description amp Module RH ontrol Unit Unit Bracket Accessory Engine Room Harness Accessory Main Harness Accessory Lamp Harness 4 Tie Wrap L 150mm QTY O voi Em clalsig 10 lt O0 ZIlo clio g F I gt Oo D Installation Instruction Replacement Template m Item B D Et TOOLS REQUIRED e Nylon removal tool e Wire cutter e 10mm Socket and driver e Phillips screw driver e Masking tape e Flash light e Scissors e 100 alcohol e Soap water e Soft non linting towel e Awl e Metric ruler 200mm Page 1 of 13 B66M0 1AAO0B II Rev 10 22 2013 PRE I NSTALLATI ON CAUTI ONS NOTES A CAUTION Dealer Installation Recommended Instructions refer to Service Manual Please read this instruction carefully before installing this product for correct installation Please DO NOT use or install the part in ways other than what is described in this instruction Manual if problem occurs during installation please contact Nissan dealer where you purchased the product Pay attention when removing trim parts to avoid breaking clips 1 Apply Parking Brake 2 Make sure the shift lever is engaged in P or N position 3 Record customer Radio Presets Preset 1 2 l 3 j 4 5 6
8. grommet for Accessary Engine Room Harness See next page for instruction 22 Secure Accessory Engine Room Harness Secure the Accessory Engine Room Harness to hood lock cable with Tape 2 places as shown in Fig 17 Way to cut Tape Cut the Tape in half Accessory Engine Room Harness 4 CAUTION Clean mounting surface with 100 alcohol Page 10 of 13 B66M0 1AAO0B II Rev 10 22 2013 INSTALLATION PROCEDURE Fig 18 7 LE 1 i VA L it L i 1 it ti l i 14 1 a4 14 Lot Lk 1 i l L 1 Li i AIi jj 1 1 pi L l i LE f Hood lock wire Fig 20 gt Terminal Grommet _ oa I 7 l lt Vinyl tube AN Fas Pom A Corrugate Vinyl tube g lt J Corrugate tube Page 11 of 13 23 Pierce a pin hole with an awl in the hood lock wire grommet as shown in Fig 18 4 CAUTION When piercing grommet use caution and do not cut wire 24 Expand the hole with a Phillips screw driver as shown in Fig 19 25 Insert the terminal of Accessory Engine Room Harness through the grommet until vinyl tubing contacts grommet Shown in Fig 20 26 Cut 10mm wide strip of Butyl Tape a Apply Butyl Tape to seal the pierced hole on the grommet b Clean panel with 100 alcohol and attach the Tape Shown in Fig 21 B66M0 1AA0B II Rev 10 22 2013 INSTALLATION PROCEDURE Fig22 a Accessory Main Harness Accessory Engine Room Harness
9. nnect harness from instrument lower panel LH taut Se Shown in Fig 7 WN i v A PEN K Hood opener Xo Screw Page 5 of 13 B66M0 1AAOB II Rev 10 22 2013 INSTALLATION PROCEDURE 11 Front kick plate inner LH removal Pull up on front kick plate inner to disengage pawls Shown in Fig 8 a Pawl aa r OEF Metal clip 12 Dash side finisher LH removal Pull dash side finisher LH to disengage mounting clips 2 places Shown in Fig 9 C Clip Dash side finisher LH 13 Fuse box removal Fuse box Screw a Remove the mounting screws 2 from the fuse box b Disconnect fuse box connectors 3 places Shown in Fig 10 Fuse box connector x3 Page 6 of 13 B66M0 1AAOB II Rev 10 22 2013 INSTALLATION PROCEDURE LAMP MODULE INSTALLATION 14 Control Unit installation a Attach Control Unit Bracket to Control Unit as shown in Fig 11 b Secure the Control Unit with Bolt and Nut as shown in Fig 11 Faery 15 Lamp Module installation Pe gOS a Secure the Lamp Module at the P WA headlamp extension panel position using previously removed bolt Headlamp LH Lamp Module b Connect the Accessory Lamp Front bumper Harness to Control Unit and Lamp Module Harness LH RH as Shown in Fig 12 Accessory RH Lamp Harness Connector Page 7 of 13 B66M0 1AAO0B II Rev 10 22 2013 INSTALLATION PROCEDURE FR Fig13 Rr Tie Wrap L 150mm Front Bumper
Download Pdf Manuals
Related Search