SPARC Enterprise M3000 Server Product Notes For XCP
Contents
1. 3 When you update follow the procedure in Updating XCP From External Media or Updating XCP From the Network to update XCP and confirm the version 32 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Identifying Degraded Memory in a System 1 Log in to XSCF 2 Type the following command XSCF gt showstatus The following example identifies that DIMM number 0A on the Motherboard unit has degraded memory XSCF gt showstatus MBU_A Status Normal MEM OA Status Degraded Information About Software 33 34 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 20102. Description Workaround 6608404 Hot plug of the X4447A Z PCI e Quad port Gigabit Ethernet Adapter UTP card might cause other network devices to fail To avoid the defect do not install this card Information About Software 27 TABLE 10 Solaris OS Issues Fixed in Solaris 10 10 08 Continued CR ID Description Workaround 6679370 The following message may be output on the This has been fixed in patch 137137 09 console during the system booting Note Before adapting the patch delete the following setting from etc system SUNW MSG ID SUN4 8000 75 TYPE set pcie expected ce mask 0x2001 Fault VER 1 SEVERITY Critical tee Workaround DESC Add the following to etc system and then A problem was detected in the PCI reboot the domain Express subsystem Refer to http sun com msg SUN4 set pcie expected ce mask 0x2001 8000 75 for more information 6720261 If your domain is running Solaris 10 5 08 OS This has been fixed in patch 137137 09 the system might panic trap during normal operator Workaround Set the following parameter in the system specification file etc system set heaplp use stlb 0 Then reboot the domain Software Documentation Updates This section contains late breaking software information that became known after the documentation set was published and corrections in the SPARC Enterprise M3000 server software documentation The corrections for SPARC Enterprise M3000 M4000 M500
3. if and execute the sethttps 8 command again the number of characters specified in a parameter exceeds 100 it might result in an internal error and you might fail to create the certificate RTIF1 Once domain detected a failure related to This error log can be safely ignored 091109 001 DIMM or PCI the error log about this detected failure is registered every time you reset XSCF 22 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Solaris OS Issues and Workarounds This section contains information about Solaris OS issues TABLE 7 TABLE 8 TABLE 9 and TABLE 10 list issues you might encounter depending upon which Solaris OS release you are using Solaris OS Issues and Workarounds for All Supported Releases TABLE 7 lists Solaris OS issues that you might encounter in any supported release of Solaris OS TABLE7 Solaris OS Issues and Workarounds for All Supported Releases CR ID Description Workaround 6481002 Installing the Solaris OS from the network If you are using a Sun PCI E Dual Gigabit using certain PCI Express cards may cause a Ethernet Adapter MMF card or a Sun PCI E panic Dual Gigabit Ethernet Adapter UTP card do not install the Solaris using either of these cards Instead use other network devices such as the onboard Gigabit Ethernet or another network device 6519290 Large amounts of I O on swap devices can Set the following to etc system and then cause the system to
4. 2010 Hardware Documentation Updates This section contains late breaking hardware information that became known after the documentation set was published and corrections in the SPARC Enterprise M3000 server hardware documentation TABLE 3 lists known documentation updates TABLE3 Hardware Documentation Updates Title Page Number Update SPARC Enterprise 1 25 1 4 6 2 SAS Port M3000 Server Overview The article on SAS Port will be replaced by the following Guide The SAS port connects the server to an external device such as a tape drive which has an SAS interface For information on which devices can be connected contact a service engineer Note that the transfer rate of this port is up to 600MB s 3Gbps x 2wide Information About Hardware 11 Information About Software This section describes the special instructions and the issues about the SPARC Enterprise M3000 server software Supported Firmware and Software on page 2 XCP Issues and Workarounds on page 15 Solaris OS Issues and Workarounds on page 23 Software Documentation Updates on page 28 Identifying Degraded Memory in a System on page 33 Active Directory and LDAP SSL The XCP 1091 release introduces support for the Active Directory and LDAP SSL features Active Directory is a distributed directory service from Microsoft Corporation Like an LDAP directory service it is used to authenticate users
5. 8 0 Firefox Solaris 10 2 0t Microsoft and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries The Firefox 3 is not supported in XSCF Web Solaris OS Patch Information Patches are not required for servers running Solaris 10 10 08 OS or later Patches for Solaris 10 5 08 The following patches are required for Solaris 10 5 08 OS only on servers containing SPARC64 VII 2 52GHz processors m 119254 59 m 138866 01 m 137137 09 For additional Solaris Operating System information see Solaris OS Issues and Workarounds on page 23 Note See Software Resources on page viii for information on how to find the latest patches Installation information and README files are included in the patch download General Information About XCP 1092 3 Patches for Emulex PCI Express PCIe Cards The following Emulex cards require drivers supplied in patch 120222 26 m XSEFC402AF Sun StorageTek Enterprise Class 4Gb Dual Port Fibre Channel PCI E HBA m XSEFC401AF Sun StorageTek Enterprise Class 4Gb Single Port Fibre Channel PCI E HBA Updating to XCP 1092 To update your XCP to XCP 1092 refer to the SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCF User s Guide for instructions Resetting the XSCF Firmware After updating the XCP firmware to 1092 do not fail to reset the XSCF by using the reboot xscf 8 command
6. OR TECHNOLOGY OR THIS DOCUMENT WHICH ARE ALL PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Unless otherwise expressly set forth in such agreement to the extent allowed by applicable law in no event shall Fujitsu Limited Sun Microsystems Inc or any of their affiliates have any liability to any third party under any legal theory for any loss of revenues or profits loss of use or data or business interruptions or for any indirect special incidental or consequential damages even if advised of the possibility of such damages DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID SS com Ca Adobe PostScript Copyright 2010 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A et FUJITSU LIMITED 1 1 Kamikodanaka 4 chome Nakahara ku Kawasaki shi Kanagawa ken 211 8588 Japon Tous droits r serv s Entr e et revue tecnical fournies par Fujitsu Limited sur des parties de ce mat riel Sun Microsystems Inc et Fuji
7. SPARC Enterprise M3000 server Contact a sales representative or a certified service engineer for software resources for your SPARC Enterprise M3000 server Note For latest patch information go to Global Site http www fujitsu com global support software security products s patch info Japanese Site https software fujitsu com jp security products others unix North American Site https download computers us fujitsu com Installation information and README files are included in the patch download Accessing Documentation Note Information in these product notes supersedes the information in the SPARC Enterprise M3000 server documentation set Instructions for installing administering and using your SPARC Enterprise M3000 server is provided in the SPARC Enterprise M3000 server documentation set The documentation set is available for download from the following website Global Site http www fujitsu com sparcenterprise manual Japanese Site http primeserver fujitsu com sparcenterprise manual North American Site https download computers us fujitsu com viii SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Sun Microsystems Software for Solaris OS etc Related Manuals http docs sun com Fujitsu Welcomes Your Comments If you have any comments or requests regarding this document or if you find any unclear statements in the document please state
8. appear hung by reboot the domain overwhelming the I O system The amount of get maxfastscan 0x2000 I O required can be generated through a number of ways eg memory shortage heavy use of tmp etc 6531036 The error message network No workaround is available initialization failed appears This message can be safely ignored repeatedly after a boot net installation 6532215 volfs or dscp service may fail when domain is Restart the service if the failure is observed To booted svc platform sun4u dscp default Method 1lib svc method svc dscp start failed with exit status 95 svc system filesystem volfs defaul t Method or service exit timed out Killing contract 59 avoid the problem issue the following commands svccfg s dscp setprop start timeout_seconds count 300 svccfg s volfs setprop start timeout_seconds count 300 svcadm refresh dscp svcadm refresh volfs Information About Software 23 TABLE 7 Solaris OS Issues and Workarounds for All Supported Releases Continued CR ID Description Workaround 6537511 6660168 6668237 Bluetooth partner is hung during security tests execution If a ubc piowbeue cpu error occurs on a domain the Solaris Fault Management cpumem diagnosis module might fail causing an interruption in FMA service If this happens you will see the following output in the console log SUNW MSG ID FMD 8000 2K TYPE Defect VER 1 SEVERITY Minor EVENT
9. be forcibly powered off And in the power recovery from the forced power off a PSU illegal configuration might be registered in the error log and the power recovery might not be started RTIF1 When you execute the settelnet c After you stopped the Telnet service execute 090115 001 disable command the Telnet service will be the rebootxsc 8 command to reset XSCF stopped immediately However unless you reset XSCF by using the rebootxsc 8 command you might fail in the subsequent restart of the Telnet service RTIF1 Power recovery message is output before After the Power recovery message is 090122 001 a PSU has recovered output wait 60 seconds before removing power from another PSU RTIF1 In a system connecting multiple hosts and one All the RCI hosts shall be powered on 090220 001 or more I O units with RCI the power on operation to one of those RCI hosts may not power on any of the RCI I O units RTIF1 After replaced the motherboard unit the RCI If you have set the power interlocking to a 090220 002 power interlocking setting restores to its value other than the default replace the default value motherboard unit and then use the setpwrmode 1M command to set the power interlocking setting again RTIF1 Despite the normal status of ppp network No workaround is available 090427 001 interface for the XSCF to Solaris OS communication SNMP MIB notifies abnormal down status RTIF1 After the XSCF reset or switc
10. engagement de quelque type que ce soit de la part de Fujitsu Limited ou de Sun Microsystems Inc ou des soci t s affili es Ce document et le produit et les technologies qu il d crit peuvent inclure des droits de propri t intellectuelle de parties tierces prot g s par copyright et ou c d s sous licence par des fournisseurs Fujitsu Limited et ou Sun Microsystems Inc y compris des logiciels et des technologies relatives aux polices de caract res Par limites du GPL ou du LGPL une copie du code source r gi par le GPL ou LGPL comme applicable est sur demande vers la fin utilsateur disponible veuillez contacter Fujitsu Limted ou Sun Microsystems Inc Cette distribution peut comprendre des composants d velopp s par des tierces parties Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Java Netra Solaris Sun Ray Answerbook2 docs sun com OpenBoot et Sun Fire sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc ou ses filiales aux Etats Unis et dans d autres pays Fujitsu et le logo Fujitsu sont des marques d pos es de Fujitsu Limited Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC
11. in this server URL http primeserver fujitsu com sparcenterprise manual Information About Hardware 9 Notes on the Use of USB Memory To execute the dumpconfig 8 restoreconfig 8 or snapshot 8 command if you specify USB memory as the destination to store data prepare the USB memory as a medium in advance The data stored will include the information about the system To use USB memory you need to pay attention to the management of the USB memory in which the data stored from the data security viewpoint We do not provide guarantees to every USB memory from any manufacturers that currently on the market against its connectivity to XSCF and proper operation Depending on the USB memory in use defects such as the XSCF firmware error or reset may occur In case such defects occurred stop the use of USB memory immediately To connect the USB memory to the USB port for XSCF connect the USB memory directly to the USB port If connected via USB hub or USB extension cables it may cause errors Power Control and Operator Panel Mode Switch You can use the mode switch on the operator panel to switch between system power on off when you use the remote power control utilizing the RCI function or the automatic power control system APCS For details see the Limitations and Cautions in Preface of the SPARC Enterprise M3000 Server Service Manual 10 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April
12. local clock XSCF gt showntp 1 remote refid st t when poll reach delay offset jitter 192 168 1 2 LOCAL 0 3 u 10 1024 377 0 000 0 000 0 000 127 127 1 0 LOCL 5 1 28 64 377 0 000 0 000 0 008 Of the two NTP server outputs the upper 192 168 1 2 indicates the NTP server which is set by using the setntp 8 command The refid is LOCAL 0 which means that the local clock which has the address of 127 127 1 0 is set to the clock source of this NTP server On the other hand the lower indicates the XSCF s own local clock The address of the XSCF s own local clock is fixed to 127 127 1 0 Due to this the NTP server 192 168 1 2 is excluded from the target of XSCF time synchronization which results in the XSCF synchronizes with its own local clock With any of the following measures to avoid the trouble time can be correctly synchronized with the NTP server which is set by using the setntp 8 command Change the clock source that the NTP server being set in XSCF refers to Use the showntp 1 command and check the clock source of the NTP server which is set in XSCF An NTP server which indicates the refid of LOCAL 0 in the output is referring to the local clock which has the address of 127 127 1 0 and you should change it to refer to another clock source When you change the clock source of an NTP server make sure in advance that it has no impact on other NTP clients Change the address of the local clock of the NTP
13. m LDAP SSL offers enhanced security to LDAP users by way of Secure Socket Layer SSL technology It uses LDAP directory service to authenticate users Note For security reasons XSCF uses only LDAP over SSL protocol LDAPS to communicate with an Active Directory server or an LDAP SSL server Active Directory and LDAP SSL each provides both authentication of user credentials and authorization of the user access level to networked resources They use authentication to verify the identity of users before they can access system resources and to grant specific access privileges to users in order to control their rights to access networked resources 1 Microsoft and Active Directory are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries 12 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 User privileges are either configured on XSCF or learned from a server based on each user s group membership in a network domain A user can belong to more than one group User domain is the authentication domain used to authenticate a user Active Directory authenticates users in the order in which the users domains are configured Once authenticated user privileges can be determined in the following ways m In the simplest case user s privileges are determined directly through the Active Directory or LDAP SSL configuration on the XSCF There is a defa
14. onboard This issue will not be fixed SAS LSI controller on the SPARC Enterprise M3000 server The raidctl command can be used to view disk controller status and can be used on any PCI Host Bus Adapter HBA installed in the system 6745410 Boot program ignoresthe Kadb option which Use kmdb instead of kadb causes the system not to boot 6765239 If a SAS device containing multiple SAS Use a FUJITSU SAS card targets is connected to the onboard external SEOX7SA1F SEOX7SA1X Alternatively SAS interface it will not work properly The check for the availability of a patch for this enumeration of target IDs within the device defect may change across reboots 6872501 If 139555 08 has been applied to the domain This has been fixed in patch 143359 02 cores are not offlined when requested by the XSCF This CR effects only Solaris 10 5 09 Workaround Solaris 10 10 09 and an earlier version of U 8 with i h Solaris OS with patch 139555 08 Emnd mp PARA aplonen the Service Processor to identify the faulty core Once identified use psradm 1M on the domain to offline the core 6888928 IPMP interface fails since probe packets are This has been fixed in patch 142900 02 not sent through that interface Problem occurs with M3000 M4000 M5000 M8000 M9000 servers running any Solaris release running IPMP with patch 141444 09 installed Workaround Disable probe based failure detection Information About Software 25 Solaris OS Iss
15. setsnmp 8 command user name or password the subsequent SNMP using the correct user name traps will not be notified RTIF1 When the SNMPv3 trap has been set after the Reset the XSCF 080725 002 watchdog timeout occurred in XSCF and XSCF reset the subsequent SNMP traps will not be notified RTIF1 When FRUs are cold replaced with the system No workaround is available 081016 002 off after poweron the monitor process might not generate entries in the monitor message log identifying the replacement operation that has occurred RTIF1 In the settimezone c adddst command Specify the abbreviation of time zone and the 081225 001 when you set eight or more letters to the name of Daylight Saving Time in seven letters abbreviation of time zone and the name of or less Daylight Saving Time execution of the showlogs command induces a segmentation fault and results in an error RTIF1 Date and time of the Last Update which Please refresh the display 090108 003 displayed on the XSCF Web may not be updated Information About Software 15 TABLE4 Known Issues and Workarounds in XCP 1092 Continued ID Description Workaround RTIF1 When you use the setpasswordpolicy 8 No workaround is available 090427 005 command and set 9999999999 10 digits in Use XSCF Web Different Characters the showpasswordpolicy 8 command displays a RTIF1 When you use the sethttps 8 command to When you create the self CA or a CSR do not 1003
16. your points specifically on the form at the following URL For Users in U S A Canada and Mexico http www computers us fujitsu com www support_servers shtml su pport servers For Users in Other Countries SPARC Enterprise contact http www fujitsu com global contact computing sparce index html Preface ix x SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 General Information About XCP 1092 This section describes the general information about XCP 1092 What s New in XCP 1092 on page 1 Supported Firmware and Software on page 2 Updating to XCP 1092 on page 4 Functionality Issues and Limitations on page 4 What s New in XCP 1092 In XCP version 1092 the following new feature is introduced The following new XSCF commands are supported m setpacketfilters 8 m showpacketfilters 8 For detail see the man pages for each command The following options for specifying a proxy server and a login user name are supported in the loadcert operand of setad 8 and setldapss1 8 a p proxy m t proxy_type a u username For detail see the man pages for each command The websites which can download the latest files of XCP firmware are changed as follows a Global Site old http www fujitsu com sparcenterprise firmware new https updatesite jp fujitsu com unix en download firmware a Japanese Site old http primeserver fujitsu com sparcenterpri
17. 0 M8000 M9000 Servers XSCF Reference Manual if not otherwise specified also apply to the man pages which XSCF provides These corrections supersede the information on the man pages 28 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 TABLE 11 lists known documentation updates TABLE 11 Software Documentation Updates Title Page Number Update SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCF Reference Manual and XSCF man pages SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCEF Reference Manual sethttps 8 command adduser 8 command password 8 and setpasswordp olicy 8 commands setdscp 8 command setdualpower feed 8 command sethttps 8 command setldap 8 command The description of email operand will be changed as follows Specifies an E mail address using up to 64 characters If c selfsign or c gencsr is specified do not specify the value with only spaces The setad 8 setldapss1 8 setpacketfilters 8 showad 8 showldapss1 8 and showpacket filters 8 will be added See the man pages of each command Added the following information If the Service Processor is configured to use Lightweight Directory Access Protocol LDAP Active Directory or LDAP SSL for user account data the user name and UID if specified must not already be in use locally or in LDAP Active Directory or LDAP SSL The maximum values of sever
18. 31 001 create the self CA Certificate Authority ora specify only spaces in the e mail operand CSR with specifying only spaces for example in the e mail operand the HTTPS function might be disabled after XSCF reset RTIF1 When you start up a domain from a disk that No workaround is available 100331 002 is connected to the 8Gbps fibre channel card SEOX7F21F SEOX7F22F and if it is unable to start the domain due to causes such as disk failure an error log of FRU UNSPECIFIED might be registered 16 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 XCP Issues Fixed in XCP 1092 TABLE 5 lists XCP issues fixed in XCP 1092 TABLE5 XCP Issues Fixed in XCP 1092 ID Description Workaround RTIF1 090427 004 RTIF1 090824 001 RTIF1 091021 001 RTIF1 091109 002 In the setting of the LDAP server the number of characters which can be specified differs between XSCF Web and XSCF Shell On XSCF Web you can enter up to 128 characters The XSCF might go down and require a reboot or you might see console error messages and a core dump ereport chassis software core when one of these conditions occurs e A local account has been created with a user ID explicitly assigned to a value larger than 65536 adduser u uid e An LDAP account has been used that has a UID value larger than 65536 While Active Directory is enabled if you log in to XSCF using the user name that
19. AN communicates in the half duplex mode Due to this network communication speed may slow down or communication error may occur Do not fail to set the network device which connects with XSCF LAN to the auto negotiation mode At this time the restoredefaults 8 command is not supported At this time the e 1 P options of the snapshot 8 command are not supported 8 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Information About Hardware This section describes the special instructions and the issues about the SPARC Enterprise M3000 server hardware Notes on the Use of 200V Power Supply on page 9 Notes on DVD Drive and Discs on page 9 Notes on the Use of USB Memory on page 10 Power Control and Operator Panel Mode Switch on page 10 Hardware Documentation Updates on page 11 Notes on the Use of 200V Power Supply For the servers that have the B type plug confirm that a 15A overcurrent protection device is available outside the server If not prepare an external 15A overcurrent protection that can be achieved by means of no fuse breakers NFBs or fuses The B type plug refers to plugs other than grounding type ones with two parallel blades such as the NEMA L6 30 L6 20 L6 15 and L5 15 Notes on DVD Drive and Discs See the Notes on DVD Drives and Discs in SPARC Enterprise on the website below before using the CD DVD discs in the standard DVD drive mounted
20. Functionality Issues and Limitations This section describes the known issues and limitations at the time of this release Notes on Active Directory a While Active Directory is enabled when you attempt to login to XSCF via the telnet you might fail to login due to timeout of the query to secondary alternated server or later m If the specified timeout is too brief for the configuration the login process or retrieval of user privilege settings could fail In such case specify larger value for the timeout and then try again 4 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Notes on LDAP SSL If the specified timeout is too brief for the configuration the login process or retrieval of user privilege settings could fail In such case specify larger value for the timeout and try again Notes on Power Consumption Monitoring Function and Airflow Indicator The amount of power consumption and exhaust air might not be indicated correctly in the MIB information in the showenvironment power and the showenvironment air command output and on the XSCF Web in the following cases and you should wait for one minute and check the value again a During the server powering on or powering off or for a while after the power on or power off complete a During the active replacement of power supply unit or for a while after the active replacement complete The figures on the power consumption monitoring function and a
21. International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc SPARC64 est une marques d pos e de SPARC International Inc utilis e sous le permis par Fujitsu Microelectronics Inc et Fujitsu Limited L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une license non exclusive de Xerox sur l interface d utilisation graphique Xerox cette licence couvrant galement les licenci s de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun Droits du gouvernement am ricain logiciel commercial Les utilisateurs du gouvernement am ricain sont soumis aux contrats de licence standard de Sun Microsystems Inc et de Fujitsu Limited ainsi qu aux clauses applicables stipul es dans le FAR et ses suppl ments Avis de non responsabilit les seules garanties octroy es par Fujitsu Limited Sun Microsystems Inc ou toute soci t affili e de l une ou l autre entit en rapport avec ce document ou tout produit ou toute technologie d crit e dans les pr sentes correspondent aux gara
22. LUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFACON Contents Preface vii Technical Support vii Software Resources viii Accessing Documentation viii Fujitsu Welcomes Your Comments ix General Information About XCP 1092 1 What s New in XCP 1092 1 Supported Firmware and Software 2 Solaris OS Patch Information 3 Patches for Solaris 105 08 3 Patches for Emulex PCI Express PCIe Cards 4 Updating to XCP 1092 4 Resetting the XSCF Firmware 4 Functionality Issues and Limitations 4 Notes on Active Directory 4 Notes on LDAP SSL 5 Notes on Power Consumption Monitoring Function and Airflow Indicator 5 Notes on NTP Server 5 Notes on the NTP Server Referring to the Local Clock 5 Notes on XSCF Web 7 General Functionality Issues and Limitations 8 Information About Hardware 9 Notes on the Use of 200V Power Supply 9 Notes on DVD Drive and Discs 9 Notes on the Use of USB Memory 10 Power Control and Operator Panel Mode Switch 10 Hardware Documentation Updates 11 Information About Software 12 Active Directory and LDAP SSL 12 Configuring XSCF for Active Directory Support 14 Notes on User Account Name and UID 14 New proxyuser System Account 14 XCP Issues and Workarounds 15 Known Issues and Workarounds in XCP 1092 15 XCP Issues Fixed in XCP 1092 17 XCP Issues Fixed in Releases Earl
23. TIME Fri Apr 4 21 41 57 PDT 2008 PLATFORM SUNW SPARC Enterprise CSN 2020642002 HOSTNAME lt hostname gt SOURCE fmd self diagnosis REV 1 0 EVENT ID 6b2e15d7 aa65 6bcc bcb1 cb03a7dd77e3 DESC A Solaris Fault Manager component has experienced an error that required the module to be disabled Refer to http sun com msg FMD 8000 2K for more information AUTO RESPONSE The module has been disabled Events destined for the module will be saved for manual diagnosis IMPACT Automated diagnosis and response for subsequent events associated with this module will not occur REC ACTION Use fmdump v u lt EVENT ID gt to locate the module Use fmadm reset lt module gt to reset the module After DIMMs are replaced the corresponding DIMM faults are not cleared on the domain Restart application server If FMA service fails issue the following command on the domain to recover svcadm clear fmd Then restart cpumem diagnosis fmadm restart cpumem diagnosis This has been fixed in patch 143527 01 Workaround Use the following commands fmadm repair fmri uuid fmadm rotate 24 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 TABLE7 Solaris OS Issues and Workarounds for All Supported Releases Continued CR ID Description Workaround 6723202 The raidctl command cannot be used to No workaround is available create a hardware RAID using the
24. al options will be changed like as follows Example password i Valid values are integers with value of 1 999999999 Added the following text The specified netmask must be a subset of the default netmask based on network class The following description will be added in DESCRIPTION The dual power feed mode cannot be used with 100V power on the M4000 M5000 servers The following description will be added in EXTENDED DESCRIPTION The size of the file to be generated by sethttps 8 grows with total character count typed in the operands of configuring the self certification authority and creating a self signed web server certificate and creating a CSR If the file to be generated is too large for XSCF the command fails with an error If you see this error reduce the number of characters in the operands and execute the sethttps 8 command again Added the following information An XSCF user account user name cannot match an LDAP user name and an XSCF user account number UID cannot match an LDAP UID number Information About Software TABLE 11 Software Documentation Updates Continued Title Page Number Update SPARC Enterprise setnameserve M3000 M4000 M5000 r 8 command M8000 M9000 Servers XSCF Reference Manual The following description will be added in OPERANDS You cannot specify the loopback address 127 0 0 0 8 the network address or a broadcast address The following options for specif
25. co FUJITSU SPARC Enterprise M3000 Server Product Notes For XCP Version 1092 Manual Code C120 E621 01EN Part No 875 4648 10 April 2010 Revision A Copyright 2010 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A and FUJITSU LIMITED 1 1 Kamikodanaka 4 chome Nakahara ku Kawasaki shi Kanagawa ken 211 8588 Japan All rights reserved Sun Microsystems Inc and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in this document and such products technology and this document are protected by copyright laws patents and other intellectual property laws and international treaties The intellectual property rights of Sun Microsystems Inc and Fujitsu Limited in such products technology and this document include without limitation one or more of the United States patents listed at http www sun com patents and one or more additional patents or patent applications in the United States or other countries This document and the product and technology to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of such product or technology or of this document may be reproduced in any form by any means without prior written authorization of Fujitsu Limited and Sun Microsystems Inc and their applicable licensors if any The furnishing of this document to you does not give you any
26. e cache in filter box Change the browser cache check_doc_frequency settings value to 1 Using the XSCF Web when you import XCP or update the firmware Session ID error may be displayed on the web browser And in the Autologout setting when you specify the timeout period as over 30 minutes Internal Server Error might be displayed when you perform the firmware update Please close the current browser and open the new browser to reconnect to XSCF Web When you use the XSCF Web if a plug in such as the search tool installed with the browser remove the plug in or disable the pop up blocking General Functionality Issues and Limitations The log archive feature by the setarchiving 8 and the showarchiving 8 commands and the Log Archives menu of XSCF Web is not supported When you use the external power control interface of the external power controller the following notification signals are not supported a The OS panic or the server hardware error signal CPUN RTNU a The server hardware error signal power fail temperature error and fan error ALARM You cannot use the following user account names as they are reserved for system use root bin daemon adm operator nobody sshd rpc rpcuser ldap apache ntp admin proxyuser and default XSCF LAN is compliant with auto negotiation When you connect XSCF LAN and the network device which has been fixed to the full duplex mode according to the IEEE 802 3 rule XSCF L
27. es Products bearing SPARC trademarks are based upon architecture developed by Sun Microsystems Inc SPARC64 is a trademark of SPARC International Inc used under license by Fujitsu Microelectronics Inc and Fujitsu Limited The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements United States Government Rights Commercial use U S Government users are subject to the standard government user license agreements of Sun Microsystems Inc and Fujitsu Limited and the applicable provisions of the FAR and its supplements Disclaimer The only warranties granted by Fujitsu Limited Sun Microsystems Inc or any affiliate of either of them in connection with this document or any product or technology described herein are those expressly set forth in the license agreement pursuant to which the product or technology is provided EXCEPT AS EXPRESSLY SET FORTH IN SUCH AGREEMENT FUJITSU LIMITED SUN MICROSYSTEMS INC AND THEIR AFFILIATES MAKE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND EXPRESS OR IMPLIED REGARDING SUCH PRODUCT
28. es on XSCF Web Under the Windows 7 and Internet Explorer 8 0 environment XSCF Web does not support the use through the built in Administrator account m On Internet Explorer 8 0 when you move the on screen horizontal frame up or down to change the frame height and use the Monitor Msg Show Hide button the screen background color may turn black In this case click Refresh on the View menu or press F5 key to refresh the display to go back to the screen right after the login When you moved the on screen horizontal frame up or down to change the frame height do not use the Monitor Msg Show Hide button m To use XSCF Web on the SPARC Enterprise M3000 server which is installed the XCP 1080 disable the cache function of your browser If you leave the browser cache function enabled the old cached data might be displayed To disable the cache funtion a Internet Explorer 6 and 7 Tools gt Internet Options gt Advanced tab and check the Do not save encrypted pages to disk box a Netscape 7 1 or later Edit gt Preferences gt Advanced gt Cache gt Compare the page in the cache to the page on the network setting and select the Every time I view the page radio button 1 Windows is either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries General Information About XCP 1092 7 a Firefox 2 Type about config in address box then typ
29. f the domain cannot be started due to reasons such as disk failure the error log might not be registered The loadcert console operand is missing in the usage of the setad 8 command and the set ldapss1 8 command To delete all the DNS servers or the search paths which are same specify just one corresponding address or domain name In doing so all the DNS servers or the search paths which are same will be deleted Register the data again as needed No workaround is available For how to use the loadcert console operand of the setad 8 command and the set1ldapss1 8 command see the man page 18 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 XCP Issues Fixed in Releases Earlier Than XCP 1092 TABLE 6 lists XCP issues that have been fixed in releases earlier than XCP 1092 TABLE6 XCP Issues Fixed in Releases Earlier Than XCP 1092 ID Description Workaround RTIF1 While XSCF is running a process may go Check that XSCF is started If not started stop 070418 009 down a watchdog timeout may occur or a the domain and then execute the system power hang up may occur After this XSCF may off on AC OFF ON To turn on the system reset power that you turned off wait at least 30 seconds before power on RTIF1 While XSCF is running watchdog timeout Check that XSCF is started If not started stop 070528 002 may occur and XSCF may reboot the domain and then execute the system power off o
30. hing you cannot No workaround is available 090427 002 login to XSCF using the LDAP server Log in to active XSCF with initial account and execute the following command to re import the certificate chain setldap c lt remote file gt RTIF1 After you set https using the self certificate To set the self certificate authority do not 090430 001 authority by XSCF and created a web server specify a blank character certificate https is not enabled Information About Software 21 TABLE6 XCP Issues Fixed in Releases Earlier Than XCP 1092 Continued ID Description Workaround RTIF1 In a domain mounted with the 10 Gigabit The entire output can be safely ignored 090508 001 Ethernet card SEOX7HE1F when you set the To avoid these outputs execute the following OpenBoot PROM environmental variable command at the ok prompt and set the diag switch to true the following OpenBoot PROM environmental variable warning message appears on the console and qiag switch to false at the same time Msg Device error setenv diag switch false FCode informed error is recorded in the error log WARNING pci 7 700000 FCODE map in doesn t match decoded register type And when you execute the showstatus 8 command Degraded might be indicated to the FRU which has installed the relevant card RTIF1 When you use the sethttps 8 command to Specify up to 100 characters in the parameter 090729 001 create a self signed web server certificate
31. ier Than XCP 1092 19 Solaris OS Issues and Workarounds 23 Solaris OS Issues and Workarounds for All Supported Releases 23 Solaris OS Issues Fixed in Solaris 10 10 09 26 Solaris OS Issues Fixed in Solaris 105 09 26 Solaris Issues Fixed in Solaris 10 10 08 27 Software Documentation Updates 28 Identifying Degraded Memory in a System 33 vi SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Preface These product notes contain late breaking information about the SPARC Enterprise M3000 server hardware software or documentation that became known after the documentation set was published Note Once an XCP version newer than the XCP version supported by this manual is released only the manuals related to the new XCP version are subsequently updated You must therefore check the manuals for the latest XCP version in addition to those related to the XCP version you are using Global Site http www fujitsu com sparcenterprise manual Japanese Site http primeserver fujitsu com sparcenterprise manual North American Site https download computers us fujitsu com Technical Support If you have technical questions or issues that are not addressed in the SPARC Enterprise M3000 server documentation contact a sales representative or a certified service engineer vii Software Resources The Solaris Operating System and Sun Java Enterprise System software are preinstalled on your
32. irflow indicator respectively represent the dissipation power and volume of air exhausted from the server The figures of peripheral devices are not included Notes on NTP Server m We recommend the domain to use the XSCF Unit as NTP server In this case pay attention to the following points a XSCF must be connected to an external NTP server a When you connect one or more NTP servers in addition to XSCF connect the same NTP server as XSCF is using For details on NTP server contact a service engineer For details on NTP settings refer to the SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCF User s Guide Notes on the NTP Server Referring to the Local Clock When the NTP server which XSCF refers to is referring to the server s own system time local clock and when the address of 127 127 1 0 is set to that local clock time synchronization in XSCF might fail General Information About XCP 1092 5 The address of the XSCF s own local clock is fixed to 127 127 1 0 On the other hand when the address of the local clock of the NTP server which XSCF refers to is set to 127 127 1 0 the address of the clock source refid has the same value as the address of the XSCF s own local clock An NTP server like this is excluded from the target of XSCF time synchronization You can execute the showntp 1 command to refer to the address of the NTP server s own clock source which is set in XSCF and the address of the XSCF s own
33. lashupdate 8 081006 004 the following output message and a XSCF command to retry the firmware update panic might occur kernel BUG in jffs2 do read inode at fs jffs2 readinode c xxx Information About Software TABLE6 XCP Issues Fixed in Releases Earlier Than XCP 1092 Continued ID Description Workaround RTIF1 The network configuration on the XSCF Web Use the setnetwork r command on the 081006 005 does not support the function equivalent to the XSCF shell setnetwork r comand And when you specified localhost or localdomain to the host name or the domain name the error message SessionID has expired appears RTIF1 The panic log on the XSCF Web might not be When the output is insufficient execute the 081006 006 displayed from the top of the message showlogs panic command on the XSCF shell RTIF1 The password 8 command indicates that the No workaround is available 081006 007 user operand is optional but will fail if a Specify the user operand to execute the user operand is not included when other password 8 command when you specify options are specified other options RTIF1 SNMP trap host configuration changes are not Modify the SNMP setting 081006 011 valid until setsnmp disable and setsnmp XSCF gt setsnmp disable Chapt XSCF gt setsnmp enable RTIF1 Power failure at the commercial AC supply No workaround is available 081016 001 connector to the UPS does not send notification send trap RTIF1 In In
34. mand or the dtrace lockstat provider 26 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 TABLE9 Solaris OS Issues Fixed in Solaris 10 5 09 Continued CR ID Description Workaround 6680733 Sun Quad port Gigabit Ethernet Adapter UTP This has been fixed in patch 139570 01 QGC amp Sun Dual 10 GigE Fiber XFP Low Profile Adapter XGF NICs might panic under high load conditions 6689757 Sun Dual 10 GigE Fiber XFP Low Profile This has been fixed in patch 139570 01 Adapter XGF with a single or improperly installed XFP optical transceivers might cause Workaround the followi to sh th le Jose SET OE Hs e SUN Check and make sure that both XFP optical The Ee opera transceiver ae transceivers are firmly seated in the housing broken or missing Do not mix INTEL and Sun XFP optical transceivers in the same Adapter Do NOT plumb a port with the ifconfig command if the port does not contain an XFP optical transceiver or it contains one but the transceiver is not in use 6725885 cfgadm will display non existent SPARC This has been fixed in patch 140401 01 Enterprise M3000 system boards SB1 to SB15 The cfgadm output for SB1 SB15 can be ignored Solaris Issues Fixed in Solaris 10 10 08 TABLE 10 lists issues that have been fixed in Solaris 10 10 08 OS You might encounter them in supported releases earlier than Solaris 10 10 08 TABLE 10 Solaris OS Issues Fixed in Solaris 10 10 08 CR ID
35. n AC OFF ON To turn on the system power that you turned off wait at least 30 seconds before power on RTIF1 When remote power control mode of After the motherboard unit is replaced 070824 001 interlocking mechanism for power supply to configures the RCI again and sets the remote domain is enabled after the motherboard unit power control mode is replaced the interlocking for power supply by RCI cannot work RTIF1 The snmp daemon might quit To restart the snmp daemon issue the 071102 002 command setsnmp enable RTIF1 After set the Daylight Saving Time by using No workaround is available 080725 004 the XSCF shell XSCF Web does not show the Use the showlogs 8 command of the XSCF correct time in the Logs menu shell RTIF1 The error log XSCF FMEM write error Power off AC OFF the system and power on 081006 001 recorded and the firmware update might fail AC ON again Then re execute the firmware update RTIF1 In the setemailreport 8 command when Do not specify over 255 characters in the SMTP 081006 002 you specified over 255 characters in the SMTP address address an error results RTIF1 During the domain operation after the XSCF eplace the motherboard unit only When no 081006 003 reset due to the XSCF unit failure the failure found on the memory you do not need hardware status shows Deconfigure in the to replace the memory status of CPU and memory RTIF1 During the firmware update there might be Reset XSCF and use the f
36. ngs menu of the XSCF Web Remote users can log in and use the XCSF Web once they have been authenticated by Active Directory or LDAP SSL Note If you are an Active Directory or LDAP SSL user do not upload a public key If one has already been uploaded use the following command to delete it XSCF gt setssh c delpubkey a u proxyuser If you are an Active Directory or LDAP SSL user be sure to log in to the XSCF network through the SSH service by the authentication not with the user public key but with the password Information About Software 13 Configuring XSCF for Active Directory Support The commands setad 8 and showad 8 let you set and view the Active Directory configuration from the command line By default Active Directory support is disabled To enable Active Directory support use the following command XSCF gt setad enable To disable Active Directory support use the following command XSCF gt setad disable To show if Active Directory support is enabled or disabled enter XSCF gt showad Use the setad 8 command with its various parameters to configure Active Directory For example you can use it to set up one primary and five alternate Active Directory servers assign group names and privileges configure a particular user domain control logging of diagnostic messages and more User domain can be configured explicitly through the setad userdomain command on XSCE
37. nties express ment stipul es dans le contrat de licence r gissant le produit ou la technologie fourni e SAUF MENTION CONTRAIRE EXPRESSEMENT STIPULEE DANS CE CONTRAT FUJITSU LIMITED SUN MICROSYSTEMS INC ET LES SOCIETES AFFILIEES REJETTENT TOUTE REPRESENTATION OU TOUTE GARANTIE QUELLE QU EN SOIT LA NATURE EXPRESSE OU IMPLICITE CONCERNANT CE PRODUIT CETTE TECHNOLOGIE OU CE DOCUMENT LESQUELS SONT FOURNIS EN L TAT EN OUTRE TOUTES LES CONDITIONS REPRESENTATIONS ET GARANTIES EXPRESSES OU TACITES Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALIT MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULI RE OU A L ABSENCE DE CONTREFA ON SONT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Sauf mention contraire express ment stipul e dans ce contrat dans la mesure autoris e par la loi applicable en aucun cas Fujitsu Limited Sun Microsystems Inc ou l une de leurs filiales ne sauraient tre tenues responsables envers une quelconque partie tierce sous quelque th orie juridique que ce soit de tout manque 4 gagner ou de perte de profit de probl mes d utilisation ou de perte de donn es ou d interruptions d activit s ou de tout dommage indirect sp cial secondaire ou cons cutif m me si ces entit s ont t pr alablement inform es d une telle ventualit LA DOCUMENTATION EST FOURNIE EN L ETAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXC
38. option or you must omit the m option setupfru 8 The following description will be added in EXTENDED command DESCRIPTION Although a CMU with two CPUMs can be configured into Quad XSB mode on an M8000 M9000 server the server generates a configuration error message for these XSBs that do not have a CPUM and memory 30 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 TABLE 11 Software Documentation Updates Continued Title Page Number Update SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCF Reference Manual SPARC Enterprise M3000 M4000 M5000 M8000 M9000 Servers XSCF User s Guide setupplatfor m 8 command showdevices 8 command showenvironm ent 8 command showhardconf 8 command showlogs 8 command Added the following information An XSCF user account user name cannot match an LDAP user name and an XSCF user account number UID cannot match an LDAP UID number The following description will be added in EXTENDED DESCRIPTION The showdevices 8 command displays a complete list of devices when executed right after a Solaris OS boot or a DR operation However when executed at other times showdevices does not display a complete list if the Solaris OS has unloaded drivers for any unused devices To be certain the displayed list is complete run the devfsadm command with v option on the domain before running showdevices For more information ab
39. or entered at login prompt using the form user domain See the setad 8 and showad 8 man pages and the note about these commands in TABLE 11 Notes on User Account Name and UID If the Service Processor is configured to use Lightweight Directory Access Protocol LDAP Active Directory or LDAP SSL for user account data the user name and UID if specified must not already be in use locally or in LDAP Active Directory or LDAP SSL New proxyuser System Account To support Active Directory and LDAP SSL this release features a new system account named proxyuser Verify that no user account of that name already exists If one does use the deleteuser 8 command to remove it then reset XSCF before using the Active Directory or LDAP SSL feature 14 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 XCP Issues and Workarounds This section contains information about XCP issues TABLE 4 TABLE 5 and TABLE 6 list issues you might encounter depending upon which XCP release you are using Known Issues and Workarounds in XCP 1092 TABLE 4 lists known XCP issues and possible workarounds in XCP 1092 TABLE4 Known Issues and Workarounds in XCP 1092 ID Description Workaround RTIF1 In setsnmp addv3traphost when the No workaround is available 080725 001 authentication failed due to the reasons such Confirm that the SNMP trap host is working as the trap host not working or the wrong and re execute the
40. out the devfsadm command see the Solaris devfsadm 1M man page Following information will be added Airflow volume information is not supported on the M4000 M5000 servers The power consumption information is displayed on the M3000 M4000 M5000 servers will be replaced by The power consumption information is displayed on the M3000 server The example of M3000 server with DC power will be added in the EXAMPLES section Added the new status Information and Notice in the error log Changed Power Failure and AC Restored to Pow Fail Rcov in the power log The description of this feature described in Supported Firmware and Software on page 2 has not yet been added Information About Software 31 TABLE 11 Software Documentation Updates Continued Title Page Number Update SPARC Enterprise 8 19 8 1 10 two sections Confirming That the XSCF Firmware Is M3000 M4000 M5000 Updated When the XSCF Unit Is Replaced in a System With a M8000 M9000 Servers Single XSCF Unit or Both Replacement in a System With XSCF User s Guide Redundant XSCF Units and Confirming That the XSCF Firmware Is Updated When the MBU Is Replaced in the M3000 server the step2 and step3 will be changed as below 2 If the replacement unit and the replaced unit have different versions a message is displayed In this case the firmware is not updated automatically The operator must match the number of the firmware versions
41. registered in the Active Directory server the showconsolepath 8 command displays not the log in user name but proxyuser In XSCF a host route cannot be set When you use the setroute 8 command and set the netmask to 255 255 255 255 it returns an invalid parameter To set 129 characters or more use XSCF Shell Use only user accounts with a user ID UID value between 100 and 60000 This is the range of auto assigned UIDs for the XSCF command adduser 8 No workaround is available To set a host route do not specify the netmask m option Information About Software 17 TABLE 5 XCP Issues Fixed in XCP 1092 Continued ID Description Workaround RTIF1 091109 003 RTIF1 091109 004 RTIF1 091105 001 When you use the setnameserver 8 command or the DNS setting of XSCF Web to register the DNS server or the search path you can specify two or more same IP address values or domain names However when you specify two or more same IP address values or domain names to delete all the DNS servers or the search paths which are same it returns an invalid parameter When you start up a domain from a disk connected to the 8 Gbps fibre channel card SEOX7F21F SEOX7F22F if you fail to specify the correct device path an error log with no message might be registered In the same way when you start up a domain from a disk connected to the 8 Gbps fibre channel card SEOX7F21F SEOX7F22F even i
42. rights or licenses express or implied with respect to the product or technology to which it pertains and this document does not contain or represent any commitment of any kind on the part of Fujitsu Limited or Sun Microsystems Inc or any affiliate of either of them This document and the product and technology described in this document may incorporate third party intellectual property copyrighted by and or licensed from suppliers to Fujitsu Limited and or Sun Microsystems Inc including software and font technology Per the terms of the GPL or LGPL a copy of the source code governed by the GPL or LGPL as applicable is available upon request by the End User Please contact Fujitsu Limited or Sun Microsystems Inc This distribution may include materials developed by third parties Parts of the product may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Java Netra Solaris Sun Ray Answerbook2 docs sun com OpenBoot and Sun Fire are trademarks or registered trademarks of Sun Microsystems Inc or its subsidiaries in the U S and other countries Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited All SPARC trademarks are used under license and are registered trademarks of SPARC International Inc in the U S and other countri
43. se download firm ware new https updatesite jp fujitsu com unix jp download firmware a The SPARC64 VII processor of 2 75GHz frequency now can be mounted on the SPARC Enterprise M3000 server Supported Firmware and Software The following firmware and operating system OS are supported depending on the processors being installed on the SPARC Enterprise M3000 server TABLE1 Supported Firmware and Operating System Versions Installed Processors XCP Version Operating System Version SPARC64 VII processors 2 52GHz XCP 1080 or later Solaris 10 5 08 or later with required patches 2 75GHz XCP 1091 or later Solaris 10 10 08 or later Note XCP 1080 is the first XCP release for the SPARC Enterprise M3000 server Note 8GB DIMM is supported in XCP 1081 or later For XCP you can download the latest files of firmware at the following websites Global Site https updatesite jp fujitsu com unix en download firmware Japanese Site https updatesite jp fujitsu com unix jp download firmware 2 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Many web browsers support the XSCF Web The browsers in TABLE 2 have demonstrated compatibility with the XSCF Web through testing For other information about XSCF Web see Notes on XSCF Web on page 7 TABLE2 Tested Web Browser Versions Web Browser Application Version Microsoft Internet Explorer 6 0 7 0 or
44. server Of the NTP server which XSCF refers to change the address of the local clock to 127 127 1 1 127 127 1 2 or 127 127 1 3 Change etc inet ntp conf of Solaris OS To enable the change restart of the NTP daemon is required When you change the address of the local clock of an NTP server make sure in advance that it has no impact on other NTP clients 6 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 Change the stratum value of the NTP server Of the NTP server which XSCF refers to change the stratum value to 1 An NTP server which has the stratum value of 1 becomes the most significant clock source and has no refid Therefore there is no chance that it will have the same address as the XSCF s own local clock When you change the stratum value of an NTP server make sure in advance that it has no impact on other NTP clients Change the address of the XSCF s own local clock By using the setntp m localaddr value command change the address of the XSCF s own local clock In value specify the least significant byte of the clock address of the local clock 127 127 1 x for value A numeric from 0 to 3 can be specified By specifying either from 1 to 3 the address of an NTP server which is referring to the local clock does not correspond to the address of the XSCF internal local clock anymore and a server which is referring to the local clock can also be set as the NTP server of XSCF Not
45. ternet Explorer 6 or 7 clicking on the Log back into the browser interface and use 081016 003 Reset button then the OK button from the the backspace key to clear text in the User Settings gt Audit gt Add Policy poupup screen text box of the popup screen instead of using will log the user out with message the Reset button Error Session Error Session ID has been expired RTIF1 When the timezone other than three characters Use the showlogs 8 command on the XSCF 081030 002 has been set the error logs cannot be shell displayed on XSCF Web Error Log page In addition XSCF Web Panic Log and IPL Message Log pages display the date on the table with RTIF1 The monitor message log might not be No workaround is available 081104 001 registered when a PCI slot error detected Use the showlogs error command or the fmdump command to check the fault information of PCI slot RTIF1 The domain console may display this message This message can be safely ignored 090108 001 ipsec_check_inbound_policy Policy Failure for the incoming packet not secure 20 SPARC Enterprise M3000 Server Product Notes for XCP Version 1092 April 2010 TABLE6 XCP Issues Fixed in Releases Earlier Than XCP 1092 Continued ID Description Workaround RTIF1 In the dual power feed system when the You need to remove and insert the power 090108 002 power failure and the power recovery cable occurred repeatedly on one line all domains will
46. tsu Limited d tiennent et contr lent toutes deux des droits de propri t intellectuelle relatifs aux produits et technologies d crits dans ce document De m me ces produits technologies et ce document sont prot g s par des lois sur le copyright des brevets d autres lois sur la propri t intellectuelle et des trait s internationaux Les droits de propri t intellectuelle de Sun Microsystems Inc et Fujitsu Limited concernant ces produits ces technologies et ce document comprennent sans que cette liste soit exhaustive un ou plusieurs des brevets d pos s aux Etats Unis et indiqu s l adresse http www sun com patents de m me qu un ou plusieurs brevets ou applications brevet es suppl mentaires aux Etats Unis et dans d autres pays Ce document le produit et les technologies aff rents sont exclusivement distribu s avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit de ces technologies ou de ce document ne peut tre reproduite sous quelque forme que ce soit par quelque moyen que ce soit sans l autorisation crite pr alable de Fujitsu Limited et de Sun Microsystems Inc et de leurs ventuels bailleurs de licence Ce document bien qu il vous ait t fourni ne vous conf re aucun droit et aucune licence expresses ou tacites concernant le produit ou la technologie auxquels il se rapporte Par ailleurs il ne contient ni ne repr sente aucun
47. ues Fixed in Solaris 10 10 09 TABLE 8 lists issues that have been fixed in Solaris 10 10 09 OS You might encounter them in supported releases earlier than Solaris 10 10 09 TABLE8 Solaris OS Issues Fixed in Solaris 10 10 09 CRID Description Workaround 6572827 The prtdiag v command reports PCI bus This has been fixed in patch 141444 09 types incorrectly It reports PCI for PCI X leaf devices and UNKN for legacy PCI devices Workaround No workaround is available 6800734 The deleteboard 8 command hang ina This has been fixed in patch 141444 09 domain No workaround is available 6827340 DR and Memory patrol might fail due to This has been fixed in patch 142344 01 command error No workaround is available Solaris OS Issues Fixed in Solaris 10 5 09 TABLE 9 lists issues that have been fixed in Solaris 10 5 09 OS You might encounter them in supported releases earlier than Solaris 10 5 09 TABLE9 Solaris OS Issues Fixed in Solaris 10 5 09 CRID Description Workaround 6588555 XSCF reset during DR operation to the This has been fixed in patch 139555 08 permanent memory might cause domain panie Workaround Do not start an XSCF reset while a DR operation is running Wait for a DR operation to finish before starting the reset 6623226 The Solaris command lockstat 1M or the This has been fixed in patch 140336 01 dtrace lockstat provider might cause a system panic Workaround Do not use the Solaris lockstat 1M com
48. ultrole parameter for both Active Directory and LDAP SSL If this parameter is configured or set all users authenticated via Active Directory or LDAP SSL are assigned privileges set in this parameter Setting up users in an Active Directory or LDAP SSL server requires only a password with no regard to group membership m If the defaultrole parameter is not configured or set user privileges are learned from the Active Directory or LDAP SSL server based on the user s group membership On XSCF the group parameter must be configured with the corresponding group name from the Active Directory or LDAP SSL server Each group has privileges associated with it which are configured on the XSCF A user s group membership is used to determine the user s privileges once authenticated Three types of groups can be configured administrator operator and custom To configure an administrator or operator group only group name is required An administrator group has platadm useradm and auditadm privileges associated with it An operator group has platop and auditop privileges associated with it To configure a custom group both group name and privileges are required For each type of group up to five groups can be configured A user assigned to more than one group receives the sum of all privileges associated with those groups To support these new features two new configuration screens Active Directory and LDAP SSL have been added to the Setti
49. ying a domain being referred to DNS server will be added c addsearch c delsearch Along with the addition of DNS search path related descritpion for DNS search path will be added in the applynetwork 8 sethostname 8 and shownameserver 8 commands For details see the the setnameserver 8 applynetwork 8 sethostname 8 and shownameserver 8 man pages setnetwork 8 The following description will be added in OPERANDS command You cannot specify the loopback address 127 0 0 0 8 the network address a broadcast address or class D or E 224 0 0 0 255 255 255 255 address setntp 8 command setroute 8 command The following description will be added in OPERANDS You cannot specify the loopback address 127 0 0 0 8 the network address or a broadcast address The following options for setting the local clock of XSCF will be added m localaddr value Along with the addition of clock address related descritpion for local addresses will be added in the showntp 8 command For details see the the setntp 8 and showntp 8 man pages The following description will be added in OPTIONS You cannot specify the loopback address 127 0 0 0 8 the network address or a broadcast address The description If you specified 0 0 0 0 in the n option do not specify the m option in OPTIONS will be changed to the following description If you specified 0 0 0 0 in the n option you must specify 0 0 0 0 in the m
Download Pdf Manuals
Related Search