Service Manual
Contents
1. ET 24 BODY EXTERIOR FRONT FENDER WHEEL OPENING MOULDING LH FRONT FENDER WHEEL OPENING MOULDING LH COMPONENTS FRONT FENDER MOLDING RH FRONT WHEEL OPENING EXTENSION PAD NO 2 FRONT FENDER LINER LH FRONT WHEEL OPENING i EXTENSION PAD NO 2 FOG LIGHT COVER RH 9 FRONT BUMPER COVER FOG LIGHT COVER LH FRONT WHEEL OPENING EXTENSION PAD NO 1 FOG LAMP EQUIPPED VEHICLES FRONT FENDER MOLDING LH G FRONT BUMPER EXTENSION LH FOG LIGHT ASSEMBLY RH FOG LIGHT ASSEMBLY LH NON REUSEABLE PART B141277J01 BODY EXTERIOR FRONT FENDER WHEEL OPENING MOULDING LH ET 25 REMOVAL 1 REMOVE FRONT FENDER MOULDING LH a Apply protective tape as shown in the illustration b Remove the 3 clips and the screw c Using a heat gun heat the front fender moulding LH double sided adhesive area HINT Heat the front bumper extension for 3 to 5 minutes at a temper ature between 40 and 60 C B142167J01 d Disengage the 5 claws and remove the front fender moulding LH 2 REMOVE FRONT FENDER MOULDING RH 3 REMOVE FRONT WHEEL OPENING EXTENSION PAD NO 2 N a Remove the front wheel opening extension pad No 2 from the aN front fender moulding REMOVE FRONT FENDER LINER LH See page ET 2 5197696101 REMOVE FRONT FENDER LINER RH REMOVE FOG LIGHT ASSEMBLY LH WITH FOG LIGHT REMOVE FOG LIGHT ASSEMBLY RH WITH FOG LIGHT oN Oo Oo REMOVE FOG LIGHT COVER LH2. WITHOUT FOG LIGHT See page ET 2 9 REMOVE FOG LIGHT COVER RH WITHOUT FOG LIGHT 10 REMOVE FRONT BUMPER COVER See page ET 2 11 REMOVE FRONT BUMPER EXTENSION LH a Using a heat gun heat the front bumper extension LH double sided adhesive area HINT Heat the front bumper extension for 3 to 5 minutes at a temper ature between 40 and 60 C b Remove the 2 clips and the 3 nuts then remove the front bumper extension LH 12 REMOVE FRONT WHEEL OPENING EXTENSION PAD NO 1 a Remove front wheel opening extension pad No 1 from the front bumper extension INSTALLATION 1 CLEAN INSTALLATION SURFACE Clip B137704J01 a Heat the double sided tape on the body using a heat gun Then wipe off the tape using a rag or piece of cloth b Clean the surface with a solvent ET 26 BODY EXTERIOR FRONT FENDER WHEEL OPENING MOULDING LH 2 CLEAN FRONT BUMPER EXTENSION AND FRONT FENDER MOULDING WHEN REUSING a CLEAN DOUBLE SIDED TAPE INSTALLATION SURFACE 1 Heat the double sided tape on the front bumper extension and the front fender moulding using a heat gun 2 While heating the tape with the heat gun use a rag or piece of cloth to wipe off the double sided tape remaining on the front bumper extension and the front fender mould ing NOTICE e Remove as much of the double sided tape as pos sible Any tape that remains may cause attach ment failure when the front bumper extension and
3. front fender moulding are installed e Use a waste cloth to scrub off because it may cause damage and attachment failure if using a driver 3 Clean the surface with a solvent 3 INSTALL FRONT WHEEL OPENING EXTENSION PAD NO 1 a Install the front wheel opening extension pad No 1 to the front FRONT WHEEL OPENING bumper extension LH with double sided tape EXTENSION PAD NO 1 4 INSTALL FRONT BUMPER EXTENSION LH a Using a heat gun heat the front bumper extension LH and the bumper cover surface b Install the front bumper extension LH to the front bumper cover with the 2 clips and 3 nuts c Firmly press the front fender moulding LH to the vehicle body NOTICE Be careful not to touch the adhesive surface with your fin gers when removing the exfoliate paper from the double sided tape INSTALL FRONT BUMPER COVER See page ET 5 REMOVE FOG LIGHT ASSEMBLY LH WITH FOG LIGHT B137704J01 REMOVE FOG LIGHT ASSEMBLY RH WITH FOG LIGHT XN Ow REMOVE FOG LIGHT COVER LH WITHOUT FOG LIGHT See page ET 6 9 INSTALL FOG LIGHT COVER RH WITHOUT FOG LIGHT 10 INSTALL FRONT FENDER LINER LH See page ET 6 11 INSTALL FRONT FENDER LINER RH BODY EXTERIOR FRONT FENDER WHEEL OPENING MOULDING LH ET 27 12 INSTALL FRONT WHEEL OPENING EXTENSION PAD NO 2 a Install the front wheel opening extension pad No 2 to the front fender moulding using double sided tape 13 INSTALL FRONT
4. FENDER MOULDING LH a Using a heat gun heat the font fender moulding LH and the sur face of the vehicle body FRONT WHEEL OPENING EXTENSION PAD NO 2 b Engage the 5 claws and temporarily install the front fender moulding LH B137696J01 c Install the front fender moulding LH with the 3 clips and the screw d Firmly press the front fender moulding LH to the vehicle body NOTICE Be careful not to touch the adhesive surface with your fin gers when removing the exfoliate paper from the double sided tape e Remove the protective tape 14 INSTALL FRONT FENDER MOULDING RH eens Clip B142167J02
Download Pdf Manuals
Related Search