Illuminated Windshield Trim Instruction Sheet - Harley
Contents
1. 10300087 4 Short screw 2 4976 5 Long screw 10500034 6 Cable strap 6 10006 J05871 4 of 42. right side turn signal Y harness See the service manual Install turn signal bracket assembly Repeat the procedure for the opposite side front turn signal Install Illuminated Windshield Trim NOTE For best results use a stepped drill bit to slowly enlarge the size of the hole 1 See Figure 3 Using a 9 16 inch 14 5 mm drill bit enlarge the right side windshield mounting hole If possible offset J05871 the drilled hole slightly towards the bottom of the hole Enlarging the hole will allow the windshield trim wiring to pass by the threaded mounting insert See Figure 4 Route the connector and wiring 1 through the enlarged hole 2 in the outer fairing Install the illumin ated windshield trim onto the front of the outer fairing Hold trim in place on outer fairing See Figure 4 Secure the wiring 1 to the inside of the outer fairing with tape 3 This allows the wiring to pass by the threaded mounting insert on the inner fairing without interference when the outer fairing is installed See Figure 1 Connect windshield trim connector 1 to the module harness trim connector 2 See the service manual Figure 3 and Figure 5 Install outer fairing Use the screws 4 and 5 and washers 3 from the kit to secure the illuminated windshield trim while installing the windshield FINAL ASSEMBLY Secure all wiring away from any moving parts pinch points or extreme heat 2 of 4 NOTE Verify that the i
3. the left side fairing thru hole to gain access to the turn signal bracket location c Route the right side turn signal Y harness 5 three wire to the right side thru hole to gain access to the turn signal bracket location d Route windshield trim connector 2 to the area of the right side windshield mounting location e Secure all harness wiring to existing harnesses with cable straps 8 f Make sure that wiring is not be pinched damaged or otherwise interferes with the installation of the outer fairing 1 of 4 Please dispose of materials responsibly A tie x Windshield trim connector Module harness trim connector Module Left side turn signal Y harness Pena ONO right side turn signal Y harness Right side turn signal connector 31R Left side turn signal connector 31L Cable strap 6 Figure 1 Module Harness Routing Example Connect Module Harness to Turn Signals 1 See the service manual Remove right turn signal bracket assembly See Figure 2 Locate and disconnect turn signal connector 2 from turn signal harness connector 31L or 31R 1 Install the right side turn signal Y harness 3 to the right side turn signal harness connector See the service manual Connect the turn signal connector 2 to the
4. cMOTOR HARLEY DAVIDSON WY J05871 INSTRUCTIONS REV 2014 11 13 ILLUMINATED WINDSHIELD TRIM GENERAL Kit Number 57000394 57000395 Models For model fitment information see the P amp A Retail Catalog or the Parts and Accessories section of www harley davidson com English only NOTES The illuminated windshield trim is not intended to replace the stock turn signals The illuminated windshield trim will not function properly without the stock turn signals installed Tools and Supplies Required WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer Electrical Overload NOTICE It is possible to overload your vehicle s charging system by adding too many electrical accessories If the combined electrical accessories operating at any one time consume more electrical current than the vehicle s charging system can produce the electrical consumption can discharge the battery and cause damage to the vehicle s electrical
5. gnition light key switch is in the OFF position before installing the main fuse attaching the battery cables 2 See the service manual Install main fuse 3 Turn the key switch to IGNITION but do not start the motorcycle Test for proper turn signal and illuminated windshield trim operation Proper operation of mirror cover lamps is a Illuminated windshield trim operate as running lights during normal vehicle operation b Illuminated windshield trim outer lamps flash with the corresponding turn signal when activated c BOTH illuminated windshield trim outer lamps flash when the emergency flashers are activated is08522 is08521 Washer 3 Short screw 2 Long screw Connector Oo ON Right side windshield mounting hole Illuminated windshield trim Figure 3 Install Illuminated Windshield Trim 1 Turn signal harness connector female 2 Turn signal connector male 3 Right side turn signal Y harness Figure 2 Auxiliary Fog Lamp Assembly J05871 is08528 1 Wiring 2 Hole 3 Tape Figure 4 Route Illuminated Windshield Trim Wiring 3 of 4 SERVICE PARTS is08519 Figure 5 Service Parts Illuminated Windshield Trim Table 1 Service Parts Table ltem Description Quantity Part Number 1 Module harness 69201037 2 lluminated windshield trim Not Sold Separately 3 Washer 3
6. system See an authorized Harley Davidson dealer for advice about the amount of current consumed by addi tional electrical accessories or for necessary wiring changes 00211Cc J05871 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled WARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury 00310a The illuminated windshield trim requires up to 260 mA adadi tional current from the electrical system Kit Contents See Figure 5 and Table 1 INSTALLATION Preparation WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 See the service manual Remove main fuse Install Module Harness 1 See the service manual Remove outer fairing NOTE An example of the module harness routing is shown in Figure 1 The configuration of the inner fairing components can require a different routing 2 Route the module harness similarly to the routing shown in Figure 1 When finished the routing should a Secure harness module 3 to harness connector or other feature with a cable strap 8 b Route the left side turn signal Y harness 4 one wire to
Download Pdf Manuals
Related Search