Installation Instructions
Contents
1. ry final installation of the Lighted Bat Lashes p NOTE The Lighted Bat Lashes are contoured to fit the fairing and will fit best f m in a particular area Move the Lighted Bat Lash around the fairing to find the best area X W STEP 5 Using the Lighted Bat Lashes as a guide mark the locations of the holes for the wiring harnesses with a piece of masking tape or non permanent marker This will be approximately 4 1 2 from the front tip of each light PIC 3 ae STEP 6 Remove the three Torx screws securing the windscreen to the fairing set them aside they will be re used Remove the windscreen See FIG 1 s STEP 7 Remove the four Torx screws securing the outer fairing to the inner fairing They will be reused Unplug the headlight Remove the outer fairing and gently set it on a soft sturdy surface FIG 1 gt 4 a a 4 a a NN f A A l po gt CAUTION Avoid damage to the motorcycle Protect painted surfaces with a soft cloth or blanket X a a 4 129 SNS k Oa ATTENTION Assistance is recommended to hold and support the outer FIG 1 La ii fairing after all of the Torx screws have been removed to FROM THE prevent damage OUTSIDE CAUTION MEASURE TWICE DRILL ONCE Double check all reference marks made on the fairing BEFORE drilling the fairing Kuryakyn will not be responsible for incidental or consequential damages resulting from AS VIEWED this installation ne2. STEP 8 Using a center punch mark the location on the fairing for drilling Using a 3 16 drill bit drill the holes in the fairing for the wire harnesses Use slow light pressure when drilling The material of the fairing is soft and you DO NOT want the drill s chuck to run into the fairing PAGE 2 LIGHTED BAT LASHES BLACK CHROME INSTALLATION cont ee ATTENTION The adhesive will not bond correctly if applied at temperatures less than 50 F Do not Kuryakyn attempt this installation in temperatures less than 50 F STEP 9 Using one of the supplied alcohol pads clean the area that the light will mount again to remove any residue STEP 10 Rub the adhesive backing on the Lighted Bat Lash to activate the adhesive Remove the adhesive backing route the wire harness through the hole in the fairing and apply the Lighted Bat Lash to the fairing PIC 3 using the markings you made in Step 4 as a guide Press and hold the Lighted Bat Lash in place for one minute full bonding strength will occur in 24 hours STEP 11 Repeat Steps 9 and 10 for the opposite side Be sure that the Lighted Bat Lashes line up from side to side STEP 12 Locate the two wire harnesses from the Lighted Bat Lashes and route them to the headlight area of the fairing ATTENTION Secure all wiring away from any moving parts pinch points or extreme heat Kiiryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken
3. INSTALLATION LIGHTED BAT LASHES BLACK CHROME 7269 PARTS INCLUDED 1 Black Chrome Right Lighted Bat Lash Assembly 1 Black Chrome Left Lighted Bat Lash Assembly 1 Wiring Kit Containing 4 Male Spade Connectors 4 Female T Tap Connectors 4 Scotch Lock Connectors 4 Alcohol Pads 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND ATTENTION NOTES REGARDING THE USE AND CARE OF THIS PRODUCT WARNING THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY ATTENTION This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality CAUTION This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material damage TOOLS SUGGESTED Set of Torx Wrenches Drill and Drill Bits Center Punch Masking Tape Non permanent Marker Wire Stripper Wire End Crimping Tool STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and understand all steps in the instructions before starting the installation Park t
4. abraded melted or frayed wires STEP 13 Locate the headlight wire harness In this harness there will be an orange wire l with a white strip and a black wire These may or may not be capped Remove PIC 4 A the cap from the orange wire with the white stripe i STEP 14 Strip the wire insulation back exposing the wire on both red wires from the Lighted Bat Lashes Join the two red wires from the harnesses together and attach one of the included male spades to this joined end Crimp securely Plug this male connector into the female connector on the orange wire with the white stripe Wrap this connection with electrical tape STEP 15 Strip the wire insulation back exposing the wire on both black wires from the Lighted Bat Lashes Join the two black wires from the harnesses together and attach one of the included male spades to this joined end Crimp securely E j Plug this male connector into the female connector on the black wire HEADLIGHT PLUG BLACK WIRE NOTE If the orange wire with white stripe and the black wire from the l 7 headlight are already being used to power another accessory then PIC 5 install one of the included Female T Tap connectors on each of these wires and plug the red wires from the Lighted Bat Lashes to the Ay Female T Tap on the orange wire with white stripe and the black A wires from the Lighted Bat Lash to the Female T Tap on the black A wire PIC 5 x STEP 16 Plug the headlight back in and test the hea
5. dlight and Bat Lashes to see that they operate correctly STEP 17 Install the outer fairing and windscreen WARNING ENSURE PROPER HEADLIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS HEADLIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY ATTENTION It is the installer s responsibility to ensure that all of the fasteners including pre assembled are tightened before operation of the motorcycle Kuryakyn will not issue a warranty on components lost due to improper installation Periodic maintenance may be required PAGE fi a e R by TE J ine vo f y 7 A J Vs i ey LIGHTED BAT LASHES BLACK CHROME INSTALLATION
6. he motorcycle on a hard level surface and turn off the ignition ATTENTION A factory service manual may be helpful in performing this installation Do not attempt to perform this installation if you are not confident in your ability to complete all of the steps in the procedure consult a trained technician NOTE Pictures shown are of chrome parts Installation of Black parts will be the same STEP 2 Identify the left and right sitting on the bike side Bat Lashes PIC 1 cont 7269 21HD 0911 CUSTOMER SERVICE INSTALLATION QUESTIONS LIMITED WARRANTY ABOUT OUR CATALOG ee STEP 3 Clean the mounting area PIC 2 If the area is extremely dirty clean with warm water and a mild Kuryakyn soap making sure to remove all surface contaminants Rinse the area and dry completely Continue to clean the area with the supplied alcohol pads and llow th rf ry allow the surface to dry RIGHT AND LEFT SITTING ON BIKE ATTENTION Ensure the area of installation is free of grease oil dirt or other debris including wax polish products and bugs to ensure proper adhesion Kuryakyn WILL NOT issue a warranty on any parts lost due to improper installation CAUTION Avoid damage to the motorcycle Protect painted surfaces with a soft cloth or blanket STEP 4 Test fit the Lighted Bat Lash to the fairing Mark the location of best fit using sm A E CNA masking tape or a non permanent marker PIC 2 and PIC 3 This will help with T 0
Download Pdf Manuals
Related Search