COMPETITION CARBURETORS MODEL 4150
Contents
1. COMPETITION CARBURETORS MODEL 4150 ULTRA HP SERIES P N 0 80674 650 cfm 0 80675 750 cfm 0 80676 950 cfm Installation and Adjustment Instructions 199R10321 CONGRATULATIONS on your purchase of Holley ULTRA HP Series carburetor We feel that you have purchased the finest performance carburetor manufactured today Should you need information or parts assistance please contact our Technical Service Department at 1 866 GOHOLLEY or 1 270 781 9741 Monday through Friday 7 a m to5 p m CST Please have the part number of the product you purchased on hand when you call WARNING These instructions must be read and fully understood before beginning installation Failure to follow these instructions may result in poor performance vehicle damage personal injury or death If these instructions are not fully understood installation should not be attempted APPLICATIONS Calibration SECONDARIES BOOSTER TYPE 0 80674 Gasoline Mechanical Conventional 0 80675 Gasoline Mechanical Double step Down Leg 0 80676 Gasoline Mechanical Double step Down Leg NOTE These carburetors are not legal for use in California on any pollution controlled motor vehicle INTRODUCTION Holley Performance Products has written this instruction sheet for the installation of the Model 4150 ULTRA HP carburetors This instruction sheet contains all the information needed to install these carburetors Please read all the WARNINGS and NOTES as they contain valuabl2. Figure 1 1 For the mechanical fuel pump remove the coil wire and crank the engine over for 10 seconds to allow fuel bowls to fill This procedure can prevent a power valve blow out Reconnect the coil wire when finished Electric fuel pumps let the fuel bowls fill in stages by turning the ignition on and then off Let the fuel pump run for a few seconds at a time This procedure can prevent the needle from being forced up at an angle not allowing the needle to seat properly 2 Start the vehicle 3 The fuel level in the clear sight glass should be mid level to slightly below center for correct float adjustment Most likely this will not need to be adjusted See Figure 1 4 If you do need to adjust this loosen the lock screw and turn the adjusting nut clockwise to lower the fuel level and counter clockwise to raise the fuel level 5 Tighten the lock screw while holding the adjustment nut Make sure the fuel level is mid level to slightly below center of the sight glass 6 If necessary flush the bowl by revving the engine a few times with the transmission in neutral IDLE SPEED SCREW The idle speed screw in most cases is the only screw you should adjust The idle speed screw controls the throttle plate position at idle which in turn raises or lowers the engine rpm by allowing more or less air fuel mixture into the engine It does not control the air fuel mixture Here are the proper steps for setting the engines idle speed 1
3. accelerator pump s delivery are the pump cam and the pump shooter discharge nozzle The pump cam determines the total volume of fuel and affects delivery rate the pump shooter affects delivery rate and helps determine the duration of the shot In general the 1 locations on the pump cams provide a moderate initial delivery and have a greater final delivered volume The 2 locations on the pump cams provide a greater initial delivery and have a lesser total delivered volume The pump shooters have a number stamped on their casting which designates the shooter size in thousandths of an inch i e a 25 shooter has a 025 discharge orifice The smaller diameter nozzles lengthen the pump shot duration and are used with heavier vehicles or with vehicles equipped with lower numerical rear axle ratios Larger diameter nozzles 035 037 shorten the pump shot duration but deliver a greater initial volume of fuel These sizes should be used on applications where engine speed will increase rapidly vehicles with good power to weight ratios Best acceleration is achieved when the accelerator pump delivers the lean best power air fuel ratio to the engine not when the maximum volume of fuel is supplied An important point should be kept in mind when tuning a Double Pumper the secondary accelerator pump must supply fuel for a sufficient time so that the secondary main nozzles can start up and deliver fuel to the engine after the secondary throt
4. an experienced carburetor tuner with access to a dynamometer that monitors air fuel ratio and BSFC Brake Specific Fuel Consumption make any changes to the factory restrictor settings as received from Holley Furthermore Holley is not responsible for any engine damage that may occur due to the carburetor being changed from the original factory calibration Power Valve Channel Restrictions PVCR These two restrictions are visible when the power valve is removed They meter the flow of fuel into the main well It is the PVCR diameter not the openings in the power valve which controls the amount of fuel admitted in the circuit Changing the size of these restrictions will lean enrich the air fuel ratio at full power but will have no effect at idle or during part throttle operation when the power valve is closed Idle Feed Restrictions IFR The idle circuit calibration is determined by the diameter of the IFR and the idle air bleed An IFR is nothing more than a metering jet for the idle system and the air bleed serves as an air flow regulating orifice Turning the idle mixture screw varies the volume of air fuel emulsion discharged into the manifold not the ratio of air to fuel in the emulsion Typically as camshaft duration and overlap are increased idle fuel jetting idle feed restriction size must be correspondingly increased to compensate for dilution and scavenging where an amount of intake charge is drawn out through a late closing ex
5. combustion will occur known as a rough idle Decreasing the idle air bleed size richens the idle mixture by increasing the pressure drop in the system Increasing idle air bleed size leans the idle mixture by reducing the pressure drop across the idle air bleeds The same conditions can be created by backing out the idle mixture screws which will increase the pressure across the idle air bleeds pushing more fuel from the idle well creating a richer fuel air ratio The idle mixture screw is the only adjustment recommended for controlling the idle fuel air mixture richness or leanness NOTE See Figure 11 for air bleed locations and identification It is recommended that all jet sizes be documented before any tuning of the air bleeds or main jets is started Below is a chart for recording the jet and air bleed sizes for your 4150 ULTRA HP Series carburetor as shipped from Holley Should you adjust the air bleed size or main jet size this chart will allow the tuner to return the carburetor to the original jetting Please place this information in a safe place along with any other documentation for your carburetor P N PRIMARY JETTING SECONDARY JETTING High Speed High Speed 0 80674 0 80675 0 80676 IDLE A AIR N 1 BLEED HIGH SPEED AIR BLEEDS Figure 11 POWER VALVES The number stamped on a power valve such as 65 indicates the manifold vacuum below which the power valve is operational In this case all manifold vacuums b
6. seconds at a time Cranking longer than 15 seconds can overheat the starter resulting in premature starter failure 2 After starting the engine check the fuel lines and inlet fittings for possible fuel leaks WARNING If any fuel leakage or weeping is detected shut off the engine immediately and wipe up any fuel Locate the source of the leak and correct before proceeding any further TUNING AND ADJUSTMENT Before you begin to tune your carburetor for your particular vehicle you must get a feel for your vehicle s performance so that any changes you make Good or Bad will be readily apparent Be patient and make only one change at a time so that only that change can be fully analyzed This cannot be overemphasized as there are no short cuts to peak performance Recording each change and the resulting performance increase or decrease will provide you with a Handbook of how vehicle performance is affected by individual carburetor adjustments This may be helpful in the future or on other applications FUEL LEVEL FLOAT LEVEL FOR ULTRA HP SERIES The float s controls the fuel delivery however if the float s are not properly adjusted a fuel starvation or a flooding effect could result This operation is difficult to do accurately on a rough idling vehicle LOCK LOCK SCREW SCREW ADJUSTING NS ADJUSTING NUT NUT SIGHT GLASS SIGHT GLASS FUEL LEVEL SLIGHTLY BELOW CENTER OF SIGHT GLASS
7. EMOVAL OF OLD CARBURETOR WARNING Prior to and after installing your new carburetor manually operate the throttle lever checking for any sticking or binding Failure to do so may result in a runaway engine or a wide open throttle condition which could result in engine damage personal injury and or death NOTE Inspect the carburetor looking for any missing parts bent levers or any possible shipping damage 1 Remove the air cleaner 2 Label any connections to the carburetor such as the fuel line 3 After labeling all connections to the carburetor carefully disconnect all hoses and lines When removing the fuel line slide a rubber cap plug over the end to prevent fuel from running out which may create a fire hazard Use a clean metal container to collect any spilled fuel DANGER DO NOT SMOKE WHEN WORKING AROUND GASOLINE OR GASOLINE VAPORS EXTINGUISH ALL OPEN FLAMES AN OPEN FLAME SPARK AND OR EXTREME HEAT COULD RESULT IN A FIRE AND OR EXPLOSION CAUSING SERIOUS INJURY DEATH AND OR PROPERTY DAMAGE 4 Remove the throttle linkage and automatic transmission controls from the throttle lever Disassemble and save the throttle return spring 5 Remove the two front and two rear attaching manifold flange nuts 6 Remove the throttle cable bracket if so equipped located at the right rear attaching bolt 7 Remove the carburetor by lifting it straight upward Sometimes the carburetor can stick to the manifold gasket requiring it
8. Find the proper idle rom on the underhood decal of your vehicle If this decal is not available find a service manual that references your vehicle and engine to find the recommended idle rpm 2 Start the engine and allow it to warm up 3 Connect a tachometer if your vehicle is not equipped with one 4 Make sure the parking brake is on and the wheels are blocked Place the automatic transmission in drive the manual transmission in neutral or as stated on the underhood decal 5 Ifthe idle speed is slower than recommended turn the screw clockwise to speed up the rpm If the idle speed is too fast turn the idle screw counter clockwise to lower the rom This adjustment should be made to both the primary and secondary screws in equal amounts so that the throttle plates are opened the same amount NOTE The Holley 4150 ULTRA HP includes the secondary idle adjustment lever P N 26 137 that allows the secondary throttle plate to be adjusted without carburetor removal SECONDARY PRIMARY 3 IDLE SPEED IDLE SPEED SCREW SCREW Figure 2 Figure 3 IDLE MIXTURE SCREWS Idle mixture screws control the air fuel mixture at idle The amount of air fuel mixture used at idle is controlled by engine vacuum So when tuning the idle mixture you are actually tuning for the best manifold vacuum Idle mixture screws are found on the metering blocks Your carburetor will have four idle mixture screws one for each venturi This is known as four corner
9. e information that can save you time and money Holley Performance Products cannot and will not be responsible for any alleged or actual engine or other damage or other conditions resulting from misapplication of the carburetor described herein However it is our intent to provide the best possible products for our customer products that perform properly and satisfy your expectations Should you need information or parts assistance please contact our Technical Service Department at 1 270 781 9741 Monday through Friday 7 a m to 5 p m Central Time please have the part number of the product that you purchased on hand when you call GENERAL INFORMATION e This instruction sheet cannot contain all of the information which may be desired by some individuals Further clarification is available in HOLLEY CARBURETORS P N 36 73 published by H P books and available at your Holley distributor e An in line fuel filter should be installed between the fuel pump and the carburetor Recommended fuel pressure should be set at 7 1 2 psi maximum 5 psi minimum Fuel pressures above 7 1 2 psi can create severe fuel control problems and are not recommended Fuel lines should be a minimum of 3 8 A non restrictive open element air cleaner kit is recommended Holley P N 120 102 The pump cam adjustment kit is available under Holley P N 20 12 Slosh tubes for preventing fuel starvation during rapid acceleration are available under Holley P N 122 5000 R
10. el air mixture causing severe engine damage property damage serious injury and or death Experimenting with air bleeds is not recommended and should only be attempted by an expert carb tuner Countless hours of testing have been performed on expensive flow stands to obtain the proper bleed size for a given calibration It is unlikely that a better air bleed calibration can be obtained however the 4150 ULTRA HP Series are equipped with removable air bleeds Here is some basic knowledge of how air bleeds work The main or high speed air bleeds affect the entire range of the main metering system The purpose of the main metering system and main air bleeds is to emulsify the fuel before entering the discharge nozzle to be discharged into the air stream in the venturi The fuel air mixture becomes leaner as air bleed size is increased Decreasing the size of the main air bleeds will decrease pressure across the main jet which in turn will pull more fuel through the main system creating a richer fuel air mixture The main or high speed air bleeds also act as an anti siphon or siphon breaker so fuel does not continue to discharge or dribble into the venturi after airflow is reduced or stopped At high speeds the fuel air mixture must be on the rich side to prevent damage to the engine The idle system supplies fuel at idle and low speeds The idle system requires a richer mixture than at cruise speed Unless the idle mixture is richer a slow and irregular
11. elow 6 5 Hg the power valve is operating Generally a 65 power valve is sufficient for most high performance applications that have a manifold vacuum of 12 Hg or higher However some problems can result with radically cammed full race machines equipped with automatic transmissions These vehicles often idle at 2000 rpm approx 6 0 Hg At this point the main nozzles are starting to feed and richen the mixture Supplied by the power valve and the engine will probably load up To correct this problem install a 45 or 35 power valve If the engine has a manifold vacuum of 12 Hg or less a good way to determine power valve size is take the manifold vacuum at idle and divide that number by two The answer is the power valve size This will provide idling and proper fuel flow under wide open throttle conditions when manifold vacuums seldom rise above 1 Hg SLOSH TUBES Slosh tubes can be used in the secondary jets to prevent the secondary main jets from being uncovered as fuel rushes to the back of the fuel bowl during extreme accelerations Holley Performance Products Toll Free Technical Service 1 866 GOHOLLEY Technical Service 1 270 781 9741 Fax 1 270 781 9772 For online help please refer to the Technical Information section of our website www holley com 199R10321 Date 2 5 04
12. haust valve Idle Feed Restrictions Pcie Power Valve Channel Restrictions Emulsion Bleeds 2 Circuit Billet Metering Block Front Model 4150 Ultra HP Series Figure 10 Emulsion Bleeds The emulsion bleeds are best tuned on the dynamometer Bleed utilization size and location can vary as will horsepower gains depending upon the engine Not all of the emulsion bleed holes have to be used to obtain peak performance Gains have been documented on use of as little as three one side of metering block of the bleed holes NOTE The emulsion bleed tuning kit P N 36 22 will support tuning of this metering block It contains ten each of the following bleed sizes Blank no hole 020 031 040 046 and 052 Individual bleeds are available from blanks to 082 from your Holley dealer under individual P Ns 142 xx xx size AIR BLEEDS WARNING Adjustment of the air bleeds is not recommended A competent mechanic with a complete and thorough knowledge of carburetors fuel systems and engine requirements should only perform air bleed adjustments Failure to follow these recommendations may result in a lean fuel air mixture causing severe engine damage property damage serious injury and or death WARNING Air bleed sizes should not be adjusted more than six 6 sizes in any one direction from the original air bleeds as shipped from Holley Air bleed adjustment beyond six 6 sizes could result in a lean fu
13. idle If you change one idle mixture screw you are required to change the other idle mixture screws the same amount Here are the proper steps for setting the idle mixture screws IDLE SCREWS located behind bracket like the other side Figure 4 1 Attach the vacuum gauge to a manifold vacuum source 2 Adjust each idle mixture screw the same amount to achieve the highest possible vacuum reading without increasing the idle speed screw 3 Now that the idle mixture is set it may be necessary to go back and reset the idle speed using the idle speed screw Continue back and forth between the tuning of the idle mixture screws and idle speed screws until little change is noticed in manifold vacuum and idle speed is correct ACCELERATOR PUMP The accelerator pump s purpose is to make up for the lag in fuel delivery This enables the engine speed to increase in response to throttle opening Differences in vehicle weight transmissions and rear axle ratios affect the amount of fuel and the delivery rate that should be provided by the accelerator pump This may necessitate the customizing of your accelerator pump to your vehicle and its use NOTE The old saying if a little is good a lot is better does not apply to the proper tuning of the accelerator pump Your car s performance can be just as bad if it receives too much fuel too soon as if it receives too little fuel too late Two factors that affect the
14. l be flange gasket spacer and another flange gasket over the manifold stud bolts WARNING The carburetor should be installed directly onto its manifold without an adapter whenever possible Sometimes an adapter can create problems with hood clearance airflow throttle linkage fuel line attachment and or fuel mixture distribution 2 Place the carburetor in position over the four stud bolts and secure in place To avoid warping the carburetor flange tighten each bolt gradually Tighten in a criss cross pattern to 60 in Ibs Be careful not to over tighten the nuts WARNING Over tightening the carburetor manifold flange hold down nuts may result in a warped or cracked carburetor throttle body The carburetor hold down nuts should be tightened down progressively in a criss cross pattern to 60 in Ibs to prevent vacuum leaks and to avoid causing damage to the throttle body A carburetor that has been damaged due to negligence of the owner will void the warranty 3 Connect the fuel lines throttle linkage and return springs Operate the linkage to ensure correct travel by fully opening and closing the throttle by hand STARTING 1 Without operating the throttle crank the engine It may take 15 to 30 seconds of cranking to allow the fuel bowls of the carburetor to fill If the engine does not start stop cranking open and close the throttle twice and crank again until the engine starts WARNING DO NOT crank the engine for more than 15
15. tle plates are opened If the nozzles do not start by the time the pump shot expires bogging will result To apply the information above follow these steps for tuning the accelerator pump Best starts or racing starts usually result when the rear tires break loose for the first 10 to 25 feet This allows engine speed to increase rapidly to get the secondary main nozzles started If wide tires which provide extremely good traction do not permit the rear tires to break loose bogging can result Best times may be recorded with narrower tires ail PUMP CAM PUMP CAM MOUNTING MOUNTING SCREW TWO LOCATIONS aa AWW EN Figure 7 Figure 8 Le Sy ey z n Fy VES 1 Change pump shooters until the smallest diameter nozzle that provides the crispest response is found 2 Then change the pump cams and locations until the right cam is found that provides even more response 3 Finally change the pump shooter once again until the crisp response is maximized NOTE Ifa nozzle size is desired that seems in between the nozzle sizes provided then the nozzle can be drilled to the desired size by using a wire drill held in a pin vise 4 Atthis point there should be no bogs flat spots or black smoke indicating excessive richness when accelerating at wide open throttle from a standing start JETTING MAIN JETS Due to varied applications that a universal performance carburetor will work with no additional t
16. to be pried loose Before prying double check to make sure all the carburetor attaching bolts and connections have been removed 8 Place clean shop towels or rags into the manifold opening to prevent dirt or debris from entering the engine Keep exposed ends of vacuum and fuel lines free from dirt WARNING Failure to cover the intake opening with a clean towel could result in dirt or debris entering the engine Dirt or debris in the induction system can cause engine damage which may necessitate a complete engine overhaul 9 Remove the gasket from the intake Remove any gasket material that may have adhered to the manifold DO NOT gouge the intake manifold sealing surface during removal of old gasket material 10 Remove the shop towels from the intake and vacuum out the intake channel to ensure no dirt or debris is left in the intake system Place a clean shop towel over the entire intake opening until you are ready to install the new carburetor FLUSHING THE FUEL LINES During fuel line installation be careful to avoid introducing any dirt particles that could enter the fuel inlet and jam open the needle and seat resulting in carburetor flooding malfunctioning and or possible engine fire In all cases where the fuel line has been cut it is essential that it be cleaned to prevent contamination from entering your new carburetor The fuel line must be flushed of rust dirt and other debris DANGER Holley DOES NOT recommend the procedure
17. uning jets have been included However a few tips on jetting are provided to help you understand their purpose Holley s Quick Change Fuel Bowls are recommended if repeated changes or experimentation with the main jets will be performed e Out of the box jetting is extremely close for most applications e In most cases it will be unnecessary to increase jet size more than four numbers greater than out of the box jetting However exceptions could arise when the carburetor is mounted on a very large volume plenum ram manifold e Carburetors are calibrated at 70 at sea level Decrease the jet size one number approx 002 for approximately every 2000 ft increase in altitude Increase jet size one number for every 35 drop in temperature e Holley jets are broached flowed and stamped according to flow rate Never drill jets this seriously alters flow characteristics Stamped numbers are reference flow numbers and DO NOT indicate drill size e Spark plugs provide the best indication of proper jetting Allow plugs to cool before jumping to conclusions TUNABLE METERING BLOCK IMPORTANT It is recommended that you document the existing adjustable bleed sizes that make up this metering block BEFORE any changes are made This billet adjustable metering block allows the user to tune the intermediate circuit restrictions idle feed restrictions emulsion bleed restrictions power valve and main jets IMPORTANT Holley highly recommends that only
18. where the coil wire is disconnected the engine cranked for a few revolutions and the fuel is collected in a container This procedure is unsafe because sparking can occur either at the coil or at the distributor end of the coil wire which may ignite any fuel spilled in the engine compartment This could cause an EXPLOSION or FIRE which may result in serious injury or death WARNING Flush fuel lines only in a well ventilated area and away from all sources of heat or flame Failure to follow these instructions may cause gasoline vapors to ignite resulting in a fire or explosion which may result in serious injury or death WARNING Wear eye protection when performing this step Failure to wear eye protection can result in gasoline or other contaminates entering the eye which could result in permanent eye damage or blindness 1 Disconnect the fuel line at the fuel pump 2 Using a compressed air source blow the fuel line clean INSTALLATION OF NEW CARBURETOR WARNING Holley Performance Products highly recommends that a quality fuel filter be installed with any replacement carburetor to catch any dirt that may still remain in the system Any dirt that may enter the carburetor can cause the carburetor to flood or malfunction A carburetor that has a malfunction caused by dirt in the system due to negligence of the owner will void the warranty 1 Install a flange gasket on the manifold If a spacer is being used the installation order wil
Download Pdf Manuals
Related Search