View the Installation Instructions
Contents
1. 9 Install the wheels on the vehicle and torque the wheel nuts to127 N m 95 Ibf ft 3 of 4 Perform step 10 for models not equipped with standard 18 wheels 10 Open the driver s door Using isopropyl alcohol thoroughly clean the area where the accessory Tire Pressure Information Label will attach Remove the adhesive backing from the label and attach it over the standard label as shown TIRE PRESSURE INFORMATION LABEL a ACCESSORY TIRE PRESSURE INFORMATION LABEL STANDARD TIRE PRESSURE INFORMATION LABEL 11 Drive the vehicle for at least 40 seconds at a speed of 15 mph 24 km h or more and all the sensor IDs will be memorized automatically 12 Be sure to give the wheel cleaning information to your customer 4of4 All 40326 0808 2008 American Honda Motor Co Inc All Rights Reserved2. HONDA Accessory Application Publications No INSTALLATION 48 ALUMINUM WHEEL TENE A140326 P N 08W18 SJC 100 Issue Date PARTS LIST Parts for TPMS sensor assembly ay Aluminum wheel Tire pressure sensor assembly The illustration may differ from the actual wheel Washer Wheel center cap The illustration may differ from the actual center cap y p SS Valve nut A J WY TOOLS AND SUPPLIES REQUIRED Rachet wrench 11 mm Socket Torque wrench Isopropyl alcohol 2 Push nuts Shop towel Center cap emblem Tire pressure information label Wheel cleaning information Give this information to your customer 2008 American Honda Motor Co Inc All Rights Reserved All 40326 0808 08W18 SJC 1000 91 1 of 4 SPECIFICATIONS Rim size 18 x 7 1 2 J offset 45 Tire size P245 60R18 104T Bolt hole PCD 120 5 holes Tire pressure Front 220 kpa 2 2 kgf cm 32 psi Rear 220 kpa 2 2 kgf cm 32 psi INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers NOTE 2 of 4 This aluminum wheel is designed for use on TPMS Tire Pressure Monitoring System equipped vehicles This aluminu
3. emblem firmly against the wheel center cap with the palm of your hand for 30 seconds Slide two push nuts to the pins on the center cap emblem Note the direction of the push nuts 2008 American Honda Motor Co Inc All Rights Reserved 5 Clean the mating surface of the sensor and the aluminum wheel WASHER GROMMET SENSOR HOUSING SURFACE TIRE PRESSURE SENSOR WHEEL GENIER VALVE NUT 4 N m 3 Ibf ft ALUMINUM WHEEL TIRE PRESSURE SENSOR HOUSING PROTRUSION SENSO OF WHEEL R SURFACE _ OOO pP _ VIEWED FROM THE INSIDE OF THE ALUMINUM WHEEL 6 Install the tire pressure sensor and the washer on the aluminum wheel and tighten the valve nut finger tight Make sure the pressure sensor is resting on the wheel 7 While holding the tire pressure sensor to keep it from rotating torque the valve nut to 4 N m 3 Ibf ft You may hear a snap or pop as you torque the nut this is normal NOTE e Install the tire pressure sensor so that the sensor housing surface does not protrude into the bead area of the wheel 2008 American Honda Motor Co Inc All Rights Reserved All 40326 0808 NOTE e Do not reuse torqued grommets Doing so may cause the valve stem to leak Do not use pneumatic or electric tools on the valve nut Tightening the nut above the specified torque can damage the grommet 8 Install the tires according to the instructions in the Service Manual
4. m wheel is equipped with a TPMS sensor See the Service Manual for tire replacement procedure and TPMS sensor installation procedure The illustrations of the aluminum wheels are shown for reference purposes only Install the correct size tire Follow the instructions described in the Owner s Manual when jacking up the vehicle and removing and installing the wheels Do not overtighten the wheel nuts by placing your weight on the wrench or by using a pipe for added leverage Wheel nut torque 127 N m 95 Ibf ft Use a tire changer to install and remove the tires as described in the Operation Manual furnished with the tire changer Do not use a tire lever as it may cause damage to the tire and aluminum wheel Do not damage the wheel center cap when installing the emblems The center cap emblem kit should be installed only if the ambient air temperature is 15 C 60 F or above To allow the adhesive to cure do not wash the vehicle for 24 hours 1 All 40326 0808 Using isopropyl alcohol on a shop towel clean the area where the center cap emblem will attach CENTER CAP a PIN PUSH NUT Note the direction of the push nuts WHEEL CENTER CAP 2 PUSH N WHEEL CENTER CAP ADHESIVE BACKING CENTER CAP EMBLEM 2 PINS Remove the adhesive backing from the center cap emblem Attach the center cap emblem to the wheel center cap by aligning two pins with the holes on the wheel center cap Hold the
Download Pdf Manuals
Related Search