SPG8000 Master Sync / Clock Reference
Contents
1. button to select SYSTEM NET SETUP IP ADDRESS and then press the ENTER button Use the left lt 4 or right arrow buttons to select each number in the IP address and use the up A or down arrow buttons to change the address values to a safe default number such as all zeros Press the ENTER button to save the changes Repeat steps 6 and 7 for the Subnet Mask and Gateway addresses Press the BACK button to exit the NETWORK submenu To delete presets and user Backup existing presets or user files If you want to backup your presets or user files from memory files before you delete them so that you can restore them at a later time perform the following steps Otherwise proceed to step 12 1 2 3 Connect a USB drive to the SPG8000 generator Press the SYSTEM button to select SYSTEM PRESET Verify the status of the USB drive a Press the up A or down F arrow button to select SYSTEM USB status b Verify that the USB status is Mounted c Ifthe status is Not Mounted press the ENTER button to mount the USB drive Press the up A or down arrow button to select SYSTEM BACKUP RESTORE Press the left lt 4 or right arrow button to select one of the following Backup Presets to USB Backs up only the instrument presets to the USB drive If you are backing up only presets you will need up to 1 MB of free space on the USB drive Backup All User Data to USB Backs up all user data to2. in this flash memory Flash memory Calibration for the Settings The values Stored GPS Genlock Black Yes Manually Remove 4MX8 module are a during board U0332 calibrate the and destroy Stores leap function of calibration module back to the memory second how the user Stores leap the factory default device or information calibrates second values destroy the the module information Allow the module entire board and when obtained by to receive satellite it was last satellite information for receiving the 30 minutes to GPS signal update the leap second field Flash memory Unused None None None GPS Genlock Black No None None 4MX8 board U0741 Table 3 Nonvolatile memory devices for Option GPS May contain Type and user Data input minimum size Function data method Location To clear To sanitize GPS receiver Calculates timing Yes if Location is Mounts above the main Save a position from a Remove and assembly and position operated in stored when module board and location different from destroy the information fixed mode operated in connects to J12 with the one that was last module or fixed mode a ribbon cable and to the saved This will erase destroy the entire antenna connector on the the previous position board rear panel and save the new one 1 During normal instrument operation 4 SPG8000 Declassification and Security Instructions Table 4 Volatile memory devices for Option BG Clear and sanitize procedures Type Type an
3. Equipment NET An Interworld Highway LLC Company SPG8000 Master Sync Clock Reference Generator Declassification and Security Instructions www tektronix com FAME AM OUN OU TOI TN A A Tektronix 077 0750 00 S Copyright Tektronix All rights reserved Licensed software products are owned by Tektronix or its subsidiaries or suppliers and are protected by national copyright laws and international treaty provisions Tektronix products are covered by U S and foreign patents issued and pending Information in this publication supersedes that in all previously published material Specifications and price change privileges reserved TEKTRONIX and TEK are registered trademarks of Tektronix Inc Contacting Tektronix Tektronix Inc 14150 SW Karl Braun Drive P O Box 500 Beaverton OR 97077 USA For product information sales service and technical support In North America call 1 800 833 9200 Worldwide visit www tektronix com to find contacts in your area Table of Contents Prelate inisee aaa a e slohentedbhamdadaaned catoadaet nametuaadeiadesauaadodbiens iii Clear and samitize procedures rirrecsereriiro oiite t eon EEE E AEE E TE O EEEE 1 Memory deviGes seis cncccndcathjeg Erenn EEEE EEEE E AE ESEE E ESS 1 Troubleshooting cic iiner i e E a E EEEE EEEE E ASE E EEEE KATES EN 13 How to clear or sanitize a nonfunctional instrument 0 cece ccc eee e eee e eee en enna eeneeenaeenas 13 How to recover
4. RESET SAVE f Press the left lt 4 or right gt arrow button to select Power On Default g Press the ENTER button to save the current instrument settings as the power on default SE USA Equipment An Interworld Highway LLC Company SPG8000 Declassification and Security Instructions 15
5. YSTEM button until SYSTEM PRESET appears Press the ENTER button You will see SYSTEM PRESET RECALL displayed Press the left lt 4 or right gt arrow button until Factory Default appears Press the ENTER button Press the BACK button to exit the Preset menu Perform the previous procedure to restore the factory preset default state Press the SYSTEM button until SYSTEM PRESET appears Press the ENTER button You will see SYSTEM PRESET RECALL displayed Press the up A or down arrow button to select SYSTEM PRESET SAVE Press the left lt 4 or right gt arrow button until the display shows SYSTEM PRESET SAVE Power On Default Press the ENTER button The display will flash as it saves the preset Press the BACK button to exit the Preset menu Press the SYSTEM button until SYSTEM PRESET appears Press the up A or down arrow button to select SYSTEM NETWORK Press the left lt 4 or right arrow button to select Setup and then press the ENTER button Press the up A or down arrow button to select SYSTEM NET SETUP DHCP Press the left lt 4 or right gt arrow button to select Disable and then press the ENTER button NOTE The DHCP feature must be disabled before you can clear the network settings stored in the instrument memory SPG8000 Declassification and Security Instructions Clear and sanitize procedures Press the up A or down arrow
6. d of Backed Method Data minimum user up by of input User To size Function data battery modification method Location accessible To clear sanitize PLD Used to store Settings No Indirectly UI Option BG No Restore Disconnect EPM7128A instrument Black board factory inputs with internal settings U300 settings then registers Restore factory settings three times FPGA Used to store Settings No Indirectly Ul Option BG No Restore Disconnect EPM1K50 instrument Black board factory inputs with internal settings and U400 U500 settings then registers to generate U600 U700 Restore test signals factory settings three times SRAM 128K x Used to store Signals No Indirectly Ul Option BG No Restore Disconnect 36 IDT71V546 Composite selection Black board factory inputs test signals of U620 U720 settings then format Restore factory settings three times SPG8000 Declassification and Security Instructions Clear and sanitize procedures Table 5 Volatile memory devices for Option AG Type Type and of Backed Method Data minimum user up by of input User To size Function data battery modification method Location accessible To clear sanitize PLD Used to store Settings No Indirectly Ul Option AG No Restore Disconnect EPM7128A instrument Audio board factory inputs with internal settings U200 settings then registers Restore factory settings three times FPGA Used to store Settings No Indirectly UI Option AG No Restore Disconnect EPF10K30 i
7. e a couple of minutes When all of the files have been copied the message Finishing copy is displayed while the file system buffers are emptied This message may appear for a couple of minutes When the restore operation is complete the message Restore completed successfully is displayed before the menu display returns to normal SPG8000 Declassification and Security Instructions Troubleshooting m After the restore operation is complete press the up A or down V arrow button to select SYSTEM USB Mounted n Press the ENTER button to unmount the USB drive After the message You may now safely remove the USB drive is displayed the menu readout should change to SYSTEM USB Not mounted o Remove the USB drive from the instrument 5 If you did not restore the presets or user data files from a USB drive in step 4 then adjust the display contrast as follows a Press the SYSTEM button to select SYSTEM PRESET b Press the up A or down arrow button to select SYSTEM LCD CONTRAST c Press the left lt 4 or right gt arrow button to set the display contrast to the desired level NOTE Perform the following steps if you want to save the display contrast setting so that it will be restored when the instrument is powered on d Press the SYSTEM button to select SYSTEM PRESET and then press the ENTER button e Press the up A or down arrow button to select SYSTEM P
8. from clearing or removing memory from the instrument 00ceeee eee 13 SPG8000 Declassification and Security Instructions Table of Contents ii SPG8000 Declassification and Security Instructions Preface This document describes how to clear or sanitize the data storage memory devices in the products listed below The instructions also describe how to declassify an instrument that is not functioning These procedures are useful for customers with data security concerns Products This document applies to the following components of the SPG8000 Master Sync Clock Reference Generator SPG8000 base generator Option DPW second hot swappable redundant backup power supply Option GPS GPS master clock synchronization Option BG 2 channels of composite NTSC PAL black or HD tri level outputs plus 2 channels of composite NTSC PAL test signal outputs Option SDI 2 channels of SD HD SDI test signal generation on 2 outputs each Option 3G 3G SDI format support Option SDI required Option AG DARS output 2 AES EBU channels plus 4 audio tone outputs 8 AES EBU channels Required documents To perform the procedures in this document you will need to have access to the SPG8000 manuals listed below These manuals are available on the Tektronix Web site at www tektronix com downloads SPG8000 Quick Start User Manual Tektronix part number 071 3080 XX 077 0745 XX Japanese 077 0746 XX Russian SPG8000 Service Man
9. is displayed before the menu display returns to normal NOTE If the USB drive runs out of memory before the backup operation is complete the operation will copy as much data as it can and will then display an error message stating that the backup operation was incomplete because the drive or device is full Press the ENTER or BACK button to clear the error message After the backup operation is complete press the up A or down arrow button to select SYSTEM USB Mounted Press the ENTER button to unmount the USB drive After the message You may now safely remove the USB drive is displayed the menu readout should change to SYSTEM USB Not mounted Remove the USB drive from the instrument Delete the presets and user files from the instrument 12 13 14 Connect the instrument and a computer using an Ethernet connection as described in the SPG8000 Quick Start User Manual On the computer open an FTP client such as Windows Explorer In the Windows Explorer command box enter ftp IP address where IP address is the network address assigned to the TG8000 generator NOTE Some FTP clients may ask for login credentials In this case login with a user name of anonymous and no password SPG8000 Declassification and Security Instructions Clear and sanitize procedures 15 The Windows Explorer window should immediately connect to the instrument and show the directory structure as sh
10. k No Restore Disconnect EP2C5F256C7N instrument board U432 factory inputs with internal settings settings then registers Restore factory settings three times FPGA Used to store Settings No Indirectly Ul GPS Genlock Black No Restore Disconnect EP2C35F672C6N instrument board U732 factory inputs with internal settings settings then registers Restore factory settings three times 2 SPG8000 Declassification and Security Instructions Table 2 Nonvolatile memory devices for the SPG8000 base generator Clear and sanitize procedures Type of user Type and information Method of Data input User minimum size Function stored modification method Location Accessible To clear To sanitize Serial EEPROM Processor boot None None Factory Main U21 No NIA Remove part AT24C01B 128x8 configuration data JTAG from board and destroy NOR Flash Main storage Both Directly and Presets are Main U101 U102 Yes Perform the Remove part PC28F512P30 for processor data and indirectly saved from delete presets from board 64Mx16 Contains settings UI files and user files and destroy Operating system and presets from memory application are saved procedure programs from USB or MAC address ethernet instrument family type FPGA programming files signal logo text overlay and picture files NAND Flash Not used None None None Main U103 No N A N A K9F1G08U0A 128Mx8 Serial MRAM Oven calibration Settings Indirectly Perform Main U22 Ye
11. l SPG8000 Declassification and Security Instructions Clear and sanitize procedures Memory devices The following tables list the volatile and nonvolatile memory devices in the modules Detailed procedures to clear or sanitize these devices are shown following the tables Table 1 Volatile memory devices for the SPG8000 base generator Type Type and of Backed Method Data minimum user up by of input User To size Function data battery modification method Location accessible To clear sanitize Power PC Main Data No Indirectly Ul Main U1 Yes Set power Repeat PPC440EPX processor and remote on preset to clear settings input factory cycle process signals power three times MT47H64M16 Processor Data No Indirectly Ul Main U33 Yes Set power Repeat 64Mx16 DDR2 memory and remote U34 on preset to clear SDRAM settings input factory cycle process signals power three times 5M240ZTQFP144 Decodes Settings No Indirectly Ul Main U220 Yes Set power Repeat CPLD signals from remote on preset to clear the processor input factory cycle process to generate signals power three control lines times for the slots front panel and devices on the board Registers control aspects of the decoding EP4CE6BGA256 Phase lock Settings No Indirectly Ul Main U450 No Set power Repeat FPGA loop control remote on preset to clear 270Kbits DDS Clock input factory cycle process embedded sine wave signals power three memory gen uses
12. nstrument Audio board factory inputs with internal settings and U300 settings then registers to generate Restore test signals factory settings three times SRAM 512K x Used to store Signals No Indirectly Ul Option AG No Restore Disconnect 8 CY7C1049 audio sine selection Audio board factory inputs wave signals of signal U310 settings then Restore factory settings three times 6 SPG8000 Declassification and Security Instructions Table 6 Nonvolatile memory devices for Option SDI Clear and sanitize procedures May contain Type and user Data input minimum size Function data 1 method Location To clear To sanitize Flash 32 M x 16 FPGA Yes Written by 389 4093 00 board U321 Overwrite the option Remove part configuration processor string with dummy from board and unique module system on characters destroy ID option key SPG8000 main board using PLD U226 Option 3G only User can enter option key string from UI String must be correct to enable Option 3G PLD with internal PLD addresses No Programmed at 389 4093 00 board U226 None Remove part 512 x16 byte user decoding memory factory from board and flash memory not used destroy DDR2 32 M x 16 Used for frame Yes Load frame 389 4093 00 board Remove power Remove part picture and logo picture and U618 U711 from board and overlay functions or logo BMP destroy into mainframe then select frame picture or logo overlay function SRAM 256 K x 16 Used for te
13. own below Index ti Up to higher level directory AG7 Eh B67 LD cpu Lb eps7 E sor Ll SEQUENCE Figure 1 Example FTP view of the instrument file structure 16 In the CPU directory delete any preset files 17 In the SEQUENCE directory delete any sequence files 18 In each of the module directories delete all of the preset files and any user created picture logo text or signal files NOTE In addition to the user created files the module directories will also contain the factory default files for the standard signals and logos that are supplied with the instrument You do not need to delete the factory default files 19 After you have deleted the desired files close the FTP window SPG8000 Declassification and Security Instructions 11 Clear and sanitize procedures 12 SPG8000 Declassification and Security Instructions Troubleshooting How to clear or sanitize a nonfunctional instrument To sanitize a nonfunctional instrument remove the Main board GPS Genlock Black board SDI board and all Power Supply modules and then return the instrument to Tektronix for installation of new boards and modules How to recover from clearing or removing memory from the instrument The procedure to recover from clearing or removing memory depends on whether the memory was on a generator card or on the instrument mainframe Perform the appropriate procedure as described in this section To recover from clearing or Perfo
14. rm the following procedure to recover a generator card removing memory from a Power on the instrument generator card 2 Calibrate the generator card as instructed in the SPG8000 Service Manual 3 Reconfigure the generator card for your specific application You can find configuration information in the SPG8000 Quick Start User Manual 4 For Option GPS only a Connect a GPS signal to the generator card and let it run for 30 minutes This allows the leap second and position information to be reacquired b You are finished with the Option GPS recovery the GPS generator card will reload the system software on start up 5 For Option SDI only verify that Option 3G is enabled NOTE You need to perform the following steps only if the instrument had Option 3G enabled prior to being sanitized a Press the SYSTEM button b Press the up A or down arrow button to select SYSTEM OPTIONS c The second line of the display lists the enabled options Check that 3G is displayed e If Option 3G is not enabled you must reenter the option key for Option 3G as described in the SPG amp 000 Quick Start User Manual SPG8000 Declassification and Security Instructions 13 Troubleshooting To recover from clearing or removing memory from the SPG8000 base instrument Perform the following procedure to recover the SPG8000 base instrument 1 Power on the instrument 2 Calibrate the mainframe oscillator oven as instr
15. s Perform Remove part MR25H256 data calibration calibration from board 32Kx8 and destroy CPLD Decodes signals Settings Indirectly Software Main U220 No N A N A 5M240ZTQFP144 from the processor upgrade 8192 bits flash to generate control lines for the slots front panel and devices on the board NV flash is not used Serial EEPROM Run time data Data Indirectly Automatic U1 on Power Yes None Remove AT24C01B 128x8 for power supply over time Supply module parts from showing time also on Option DPW board and of use and secondary Power destroy can temperature time Supply module also remove related use supply from instrument and leave it in a secured area replace supply with one that has not been in a secure area CPLD Interfaces with Settings Indirectly Software Front panel U1 No NIA NIA 5M240ZTQFP100 signals from upgrade 8192 bits flash the main PLD memory not used drives LEDs and reads the buttons nonvolatile flash memory is not used SPG8000 Declassification and Security Instructions Clear and sanitize procedures Table 2 Nonvolatile memory devices for the SPG8000 base generator cont Type of user Type and information Method of Data input User minimum size Function stored modification method Location Accessible To clear To sanitize Flash memory Configuration of None None Written by GPS Genlock Black No None N A 4MX8 FPGA processor board U0331 No customer system from information is Main board stored
16. the USB drive When all user data is backed up every user file except for the FPGA configuration files will be copied to the USB drive User files are defined as any file that exists in the app FO directory on the instrument The files in this directory can include presets signal files frame picture files logo files sequence files and for Option SDI and Option 3G can also include text and font files The user data files do not include the application software or any Linux files NOTE Ifyou are backing up all of the user data in the instrument you will need up to 96 MB of free space on the USB drive SPG8000 Declassification and Security Instructions 9 Clear and sanitize procedures 6 7 10 11 Press the ENTER button to start the selected backup operation A warning message is displayed asking you to verify the operation Press the ENTER button to proceed or press the BACK button to cancel the operation Monitor the progress of the file copy operation a During the first stage of the copy process the display shows the names of the files as they are copied Depending on the size of the files being copied this may take a couple of minutes b When all of the files have been copied the message Finishing copy is displayed while the file system buffers are emptied This message may appear for a couple of minutes c When the backup operation is complete the message Backup completed successfully
17. times some of embedded volatile memory 88E1116R 10 100 1000 Data No Indirectly Ul Main U58 No Set power Repeat gigabit Ethernet remote on preset to clear ethernet PHY control factory cycle process RGMII registers power three transceiver integrated times data FIFO buffer DAC5571A Display Settings No Indirectly UI or Main U43 Yes Set power Repeat 8 bit DAC Contrast remote on preset to clear voltage factory cycle process control power three times SPG8000 Declassification and Security Instructions Clear and sanitize procedures Table 1 Volatile memory devices for the SPG8000 base generator cont Type Type and of Backed Method Data minimum user up by of input User To size Function data battery modification method Location accessible To clear sanitize 5M240ZTQFP100 volatile Settings No Indirectly UI or Front panel Yes Set power Repeat CPLD keypad remote U1 on preset to clear read back factory cycle process and LED power three drive control times registers Real Time The RTC Data Yes Direct UI or Main U16 Yes Perform Remove Clock function is not and and remote the clear part or 128x8 serial accessible settings indirect network battery NV memory but the clock settings runs and procedure will show There is no the elapsed way to clear time since the the real time board was clock built The memory is used to store user network parameters FPGA Used to store Settings No Indirectly Ul GPS Genlock Blac
18. ual Tektronix part number 077 0749 XX SPG8000 Declassification and Security Instructions iii Preface iv Terms The following terms may be used in this document Clear This removes data on media memory before reusing it in a secured area All reusable memory is cleared to deny access to previously stored information by standard means of access Erase This is equivalent to clear Media storage data export device Any of several devices that are used to store or export data from the instrument such as a USB port Nonvolatile memory Data is retained when the instrument is powered off Power off Some instruments have a Standby mode in which power is still supplied to the instrument For clearing data putting the instrument in Standby mode does not qualify as powering off For these products you must either push a rear panel OFF switch or remove the power source from the instrument Remove This is a physical means to clear the data by removing the memory device from the instrument Instructions are available in the product Service Manual Sanitize This eradicates the data from media memory so that the data cannot be recovered by other means or technology This is typically used when the device is moved temporarily or permanently from a secured area to a nonsecured area User modifiable The user can write to the memory device during normal instrument operation using the instrument interface or remote contro
19. ucted in the SPG8000 Quick Start User Manual To calibrate the oscillator you can use a GPS signal if Option GPS is installed Otherwise you can use a 10 MHz signal or a video reference signal that is known to be at a precise frequency 3 Configure the network parameters for the instrument as instructed in the SPG8000 Quick Start User Manual 4 Ifyou backed up the presets and user data files onto a USB drive before you removed the mainframe memory restore the presets or user data files as described below a Connect the USB drive to the SPG8000 generator that you used to back up the presets or user data files Press the SYSTEM button to select SYSTEM PRESET Press the up A or down Y arrow button to select SYSTEM USB status Verify that the USB status is Mounted If the status is Not Mounted press the ENTER button to mount the USB drive Press the up A or down arrow button to select SYSTEM BACKUP RESTORE Press the left lt 4 or right arrow button to select Restore Presets from USB or Restore All User Data from USB Press the ENTER button to start the selected restore operation A warning message is displayed asking you to verify the operation Press the ENTER button to proceed or press the BACK button to cancel the operation During the first stage of the copy process the display shows the names of the files as they are copied Depending on the size of the files being copied this may tak
20. xt and Yes Load text file to 389 4093 00 board If text is saved in Remove part circle overlay mainframe or U521 U0521 power on preset then from board and functions enter text string U621 U0621 should restore factory destroy from keyboard U622 U0622 preset save as power on preset then cycle power three times Dual 2048 step Holds calibration Yes Calibrate output 389 4485 00 output board Store calibration level Store calibration digital data Indirectly levels U1 and U5 at mid scale of 50 level at min and potentiometer with max three times EEPROM with then store at mid the two parts in scale of 50 parallel limited in software to 100 steps of range FPGA with 90 K Generates signals Yes Programed 389 4093 00 board U811 Remove power Set instrument Logic elements from logic and indirectly from flash to power up on and 4 5 Mb of memory also by signal at bootup factory default RAM used for burn in selection changes state and cycle power timecode and as instrument three times instrument operates configuration 128 K x 8 Unused No None 389 4093 00 board U224 None Remove part and EEPROM destroy 1 During normal instrument operation SPG8000 Declassification and Security Instructions Clear and sanitize procedures To restore the factory default settings To set the factory default settings as the power on state To clear the network settings Restore the instrument to the factory default settings as follows 1 2 Press the S
Download Pdf Manuals
Related Search