Residential Ultra Violet Disinfection System For
Contents
1. A a y Premier Residential Ultra Violet Disinfection System For Residential Reverse Osmosis RO Model UV Residential Kit Installation amp Service Manual This manual covers installation for Standard Style amp Manifold Style RO Units E Za M UV Module Watts Premier Inc 8716 W Ludlow Drive Suite 1 Peoria AZ 85381 Phone 480 675 7995 Fax 623 866 5666 Manual 199382 Manual Rev 10 28 04 Standard Style Unit DRAIN SADDLE GREEN TUBE 4 Elbow Fittings installed on unit FLOW REST RICTOR SHUT_OFF VALVE al aa Lf Manifold Style Unit Elbow Fittings provided in parts bag RAIN SADDLE BLACK TUBE BLUE TUBE D T RED TUBE BLUE TUBE K ey UV KIT BLACK TUBE BLUE TUBE i LF RED TUBE BLUE ee Marked Faucet Db BLUE TUBE Marked Ta Rev 10 1 04 Yo Ly Rev 10 1 04 Check unit for shipping damage If unit is damaged when received you will nee2. a 3 tank tube 1 Shut off water supply to RO unit amp drain tank by opening the RO faucet until water flow stops 2 Replace the two 4 elbow fittings on the top of the UV Module with the two elbow fittings supplied in the parts bag NOTE Use 2 3 wraps of Teflon tape supplied before attaching the new elbow fittings to the UV Module Do not over tighten elbow fittings or damage to module may occur 3 Cut the blue tubing feeding the storage tank from the RO unit and re connect the two ends to each end of the UV module until nuts are snug do not over tighten It does not matter which way the water flows through the UV module 4 Turn off RO faucet Turn on incoming feed water supply to the RO unit and let run until the tank fills 5 Check for leaks 6 Plug the Plastic Electrical Connectors from the UV module together with Plastic Electrical Connector on the Ballast 7 Plug ballast into electrical outlet You will see light blue light from the UV module view port Section 3 Maintenance For maximum disinfection the UV lamp should be replaced once every 12 months and the UV Cap and quartz tube should be cleaned at the same time Warning Do not touch UV Lamp or Quartz Tube with bare fingers or hands as this will shorten the lifespan of the bulb or create hot spots on the bulb Handle with clean cloth or cotton gloves If you contact the bulb wipe the bulb with common household i
3. cant i e Vaseline 7 Carefully screw clean UV Cap amp Quartz tube back onto UV housing body by turning clockwise 8 Turn on incoming feed water supply to the RO unit and let run until the tank fills Check for leaks 10 Plug the Plastic Electrical Connectors from the UV module together with Plastic Electrical Connector on the Ballast 11 Plug ballast into electrical outlet You will see light blue light from the UV module view port r A End Plug O Ring UV Cap amp Quartz Tube LZ UV Housing Body a 7 California Proposition 65 Warning WARNING this product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Installer California law requires that this warning be given to the consumer For questions regarding installation or service contact Watts Premier Inc Customer Service department toll free within the Continental United States 800 752 5582 Outside the United States 480 675 7995 E mail mail premierh20 com
4. d to make a claim with the freight carrier Item damage in shipping is not covered under warranty Check plug in ballast to make sure that it is the right voltage and hertz for your country WARNING TO PROTECT FROM ELECTRICAL SHOCK THE UV MODULE SHOULD BE UNPLUGGED WHEN WORKING ON THE UNIT Section 1 Standard Style Unit See Drawing 1 on page 2 NOTE The two elbow fittings on the top of the UV module DO NOT need to be replaced if attaching UV module to a Standard Style Unit with a 1 4 tank tube 1 Shut off water supply to RO unit amp drain tank by opening the RO faucet until water flow stops 2 Cut the 1 4 blue tubing between the storage tank amp the final filter Re connect the two ends of the tubing to each end of the UV module until nuts are snug do not over tighten It does not matter which way the water flows through the UV module 3 Turn RO faucet off Turn on incoming feed water supply to the RO unit and let run until the tank fills 4 Check for leaks 5 Plug the Plastic Electrical Connectors from the UV module together with Plastic Electrical Connector on the Ballast 6 Plug ballast into electrical outlet You will see light blue light from the UV module view port Section 2 Manifold Style Unit See Drawing 2 on page 2 NOTE The two elbow fittings on the top of the UV module WILL need to be replaced with supplied elbow fittings if attaching to a Manifold Style Unit with
5. sopropyl alcohol and dry prior to use Replacement of UV Bulb 1 Unplug ballast from electrical outlet 2 Unplug the plastic electrical connector from ballast to UV Lamp 3 Shut off water supply to RO unit amp drain tank by opening the RO faucet until water flow stops then shut off faucet 4 Using a flat blade screwdriver pry open the end of the bulb away from the UV Cap Remove UV Lamp from cap and discard 5 Carefully slide new UV Lamp into the UV cap until it is flush 6 Turn on incoming feed water supply to the RO unit and let run until the tank fills 7 Check for leaks 8 Plug the Plastic Electrical Connectors from the UV module together with Plastic Electrical Connector on the Ballast 9 Plug ballast into electrical outlet You will see light blue light from the UV module view port Cleaning of UV Cap amp Quartz Tube 1 Unplug ballast from electrical outlet Unplug the plastic electrical connector from ballast to UV Lamp 3 Shut off water supply to RO unit amp drain tank by opening the RO faucet until water flow stops 4 Remove the UV Cap amp Quartz tube by turning the cap counter clockwise 5 Clean outside of the Quartz tube the UV Cap and inside of UV housing with warm water and a mild detergent Rinse thoroughly with warm clean water and let dry 6 Lubricate UV housing o ring with water soluble lubricant i e K Y Jelly or Silicone lubricant NOTE Do not use Petroleum based lubri
Download Pdf Manuals
Related Search