Innovative Concepts in Entertainment 10123 Main Street Clarence
Contents
1. 30 You can get this game at www magic play eu You can get this game at www magic play eu Ball gate sensors Access Remove the two screws that hold the gate cam to the Primary Ball gate assembly Slide the Primary Ball gate assembly out Ball gate sensors Operation There are two magnetic sensors located under the primary ball gate assembly The primary ball gate assembly has a magnetic attached underneath so that when the assembly rotates it will pass over one of the two sensors When the ball gate assembly moves counter clock wise it will pass over the sensor for the closed position and stop the assembly When the ball gate assembly rotates clock wise it will pass over the sensor for the open position and stop the assembly Using a volt meter when the magnet passes over either of the sensors that sensor will have no voltage present When the magnet is not over the sensor it should read 5 volt of DC power With the power off on the game the sensor is normally open WARNING Never manually move the Primary Ball Gate assembly as damage will occur to the motor gearbox assembly below Gate closed Sensor 4c m d P ERR Ball gate sensors Removal To remove a sensor disconnect the two pin connector Then unscrew the tie wrap and push the sensor out To install a replace ment sensor insert the connector from the top through the hole and push firmly down Attach the wire harness and re install the wire tie2. You can get this game at www magic play eu You can get this game at www magic play eu Control Panel Small and Large Display Removal To access the two display boards remove the bolts marked with the x Lift the control panel and unplug the 5 pin Molex plug Remove the control panel and flip over Small Display did Remove plastic standoffs Disconnect Wire harness and remove Large Display Disconnect harnesses and remove Remove plastic standoffs Remove protective cover NEAL L NN You can get this game at www magic play eu You can get this game at www magic play eu Clown Reset Bracket Sensor The Clown reset bracket assembly will stand clowns back up after being knocked down During game play and when the entire row is knocked down the reset bracket assembly s motor will activate causing the bracket to push the clowns up Upon one complete turn the bracket will return to its starting position A magnet sensor is used to tell the game where the bracket is If the sensor is not working the bracket assembly will run one more time and time out If the sensor that detects that the clown has been knocked down fails then the Reset Bracket will run on that row every 30 seconds during its attract mode Sensor Home Position Sensor Replacement Unplug the two pin sensor harness attached to the bracket Cut the connector off Push old sensor out of plastic Insert new sensor into
3. HARNESS CLOWN RGB LEDS HARNESS STEPPER MOTOR INTERFACE HARNESS STEPPER MOTOR HARNESS CHEAT EXTENSION HARNESS CHEAT INTERFACE HARNESS BONUS LED EXTENSION HARNESS BONUS LED DISPLAY COVER LARGE ALL GATE FENCE SECONDARY ALL GATE FENCE PRIMARY AGE FACE LEFT AGE FACE RIGHT REBOUND GUARD ARGET BASE BOTTOM ARGET BASE MIDDLE ARGET BASE TOP VACUUM CAP VACUUM CAP ALL DIVERTER LEFT ALL DIVERTER RIGHT ASY BALL GATE ELT MATERIAL ARGET LARGE FULL ASY ARGET MEDIUM FULL ASY ARGET SMALL FULL ASY ARPET DOOR FRAME ARPET REAR DOOR DECAL REBOUND GUARD INSERT 1 DOLLAR INSERT 2 DOLLAR INSERT 2 TOKENS LAQUE SKILL GAME LOWN SHELF TOP LOWN SHELF MIDDLE LOWN SHELF BOTTOM ONUS MARQUEE BACK DECAL CARNIE MARQUEE ONUS MARQUEE FRONT MARQUEE DECAL CANNON MARQUEE ANNON GRAPHIC BACKING LAQUE FRONT CABINET DECAL MARQUEE TICKET 250 DECAL MARQUEE TICKET 500 INSERT SWIPE CARD DECAL FRONT CABINET CLOWN DECAL TICKET DOOR DECAL ICE LOGO LAQUE INSERT CNTL PANEL 250 LAQUE INSERT CNTL PANEL 500 CORE INSERT 1 CORE INSERT 50 CENTS Un 35 You can get this game at www magic play eu You can get this game at www magic play eu T MOLDING 25 32 YELLOW 105 2 POWER SUPPLY PS 1 36 You can get this game at www magic play eu You can get this game at www magic play eu J 22 WARRANTY POLICY Il C E Inc warrants all components in new machines to be free of defects
4. Part PC60615A Square Drive Bit 1 piece 5 You can get this game at www magic play eu You can get this game at www magic play eu Step 1 Position the front cabinet and the back cabinet leaving room to connect the wire harnesses Step 2 Before sliding the two halves together you need to plug in the wire harnesses There are three sets of wire harnesses The right side of the cabinet has three cables two of which are colored coded Blue goes in the middle plug red to the bottom The left side has one color plug green which goes in the middle Above that are three connectors on a small circuit board labeled J4 J5 and J6 III TA 6 You can get this game at www magic play eu You can get this game at www magic play eu Step 3 Slide the two halves together and lock the cabinets using the included large Allen wrench tool Lock the cabinet on both sides Lock the upper latches first then the bottom latches Step 4 Remove the ball gate cover using an Allen wrench The long 4 bolts go in the back while the 1 bolts go in the front Set hardware and wood cover aside a 20 x 4 4 20 x 1 1 4 5 7 You can get this game at www magic play eu You can get this game at www magic play eu Step 5 Attach the right cage using 74 20 x Joint Connectors on the outside and 4 20 7 8 AA6799 bolts on the in side There locations are shown below The front top bolt is 5
5. Sets the amount of tickets to win when 400 490 points are scored See Score chart below Ticket Multiplier 1 0 2 1 0 Just for Fun 1 1 ticket 1 ticket 2 2 tickets 1 ticket This allows you to either turn off tickets and play for a score pay out normal or pay 1 2 the amount of tickets owed Lockup 0 0 1 1 0 Normal Tilt 1 Lock the game up Fixed Ticket Override 0 0 100 1 0 Normal Setting a value will result in the game only paying that amount when played Factory Reset 0 0 1 1 Factory Reset Resets your values back to their lower settings You will then need to reconfigure to your settings 25 Game Suggestive Values 1 00 Game Suggestive Values 50 Game Suggestive Values 24 You can get this game at www magic play eu Recommended Honus Values You can get this game at www magic play eu Error Codes for Down Da Clown Error 1 Ticket Error Solution Refill Tickets Error 2 CF Error Compact flash error Solution Reseat Flash card or replace Error 3 Ball Gate Error Solution Check for proper ball gate operation See section Ball Gate Assembly Error 4 Top Motor Switch Error Top Row switch not seen Solution Check Clown Reset Bracket sensor See section Clown Reset Bracket Sensor Error 5 Middle Motor Switch Error Middle Row switch not seen Solution Check Clown Reset Bracket sensor See section Clown Reset Bracket Sensor Error 6 Bottom Motor Switch Error Bot
6. I Un RD Q QD Bon QD 2 o Bom c O D O ke Un O gt oO a QD o0 O 4 Un i c o o0 O z I QD Em c Oo B n O mi of the cabinet The inner plastic front sides will not be used EE E N LE d iS E ue i A D y PICCCCCA a i Y 3 Fu Pi See Ss Ses cy 5 ani NE n s y eae Ss 1 a Install the cabinet spacers on the insides of the two cabinets using 17 drywall screws Mounting holes are predrilled in the spacers 15 You can get this game at www magic play eu You can get this game at www magic play eu Step 18 If you pole has the extended support wings removed locate the 8 1 4 20 x 1 6049 bolts from the parts bin and attach the extended wing supports shown below Step 19 Position the center pole onto of the marquee and attach with 8 1 4 20x1 6049 bolts Step 20 Attach the large red center plastic to the center pole using 6211 Allen bolts 16 You can get this game at www magic play eu You can get this game at www magic play eu Step 21 Located inside the cabinet you will find the cable attached to the upper side of the cabinet Remove the bolts holding the control panel so you can slide the panel to expose the access hole that the marquee wire will travel through Route the wire through the cage and up to the sign Attach with wire ties This power harness is for step 26 Y
7. 8 not 7 8 See note below Repeat for the left cage p asl Hh i oe i coe i m LRL oe oo HeH TLE HTEHH T ILL i 1 Tr Say te 1 4 20x5 8 PC60601 bolt here only iam 4 Note These three are accessed from inside the cabinet and are optional Do not tighten any bolts until all of the bolts are in Start with the bolt labeled 1 and then do 2 This will ensure good alignment as you go BE CAREFUL OF YOUR FINGERS 8 You can get this game at www magic play eu You can get this game at www magic play eu Step 4 Reattach the ball gate cover using an Allen wrench The long 4 bolts go in the back while the 1 bolts go in the front Set hardware and wood cover aside t 74 20 x 1 1 4 Start at the front of the cabinet F first Then install the longer bolts s a e bd in the back Do not tighten any bolts until all are started Step 6 Position the upper brace and attach to the cage sides as shown Use a 4 20 7 8 AA6799 bolt to attach the upper brace to the cage You can get this game at www magic play eu You can get this game at www magic play eu Step 7 The long braces attach to the back of the cabinet The short braces attach to the front of the cabinet Use 20 7 8 AA6799 bolts to attach arms to cabinet See below for attaching the cheat sensor to the center Cautio
8. if installing two games togeth er Do not install the plastic front cover on the sides that will be together Jai in P Tine Wd HIT mu MIN IM MU EE ALIAM i ILL TIT E HT 3 TIT D Xm PT Mj MIN Ut tg mt TM LIT Y LA V E l M a a l M NAU N i Ht ain I E DE e A j D d AU im T Mj V i X RENE EXC x 13 You can get this game at www magic play eu You can get this game at www magic play eu Step 14 Attach the rebound guard from the back of the cages The 4 20 3 AA6369 bolts go through the front and the washers plus kep nuts in the back Do not install at this time if you are joining two cabinets together and installing a Mega marquee LT M Step 15 Attach on the right side of the game the plaque that states pure skill game using square bit screws and attach your choice of coinage on the left side of the game using square bit screws NOTE Do not install plaques on the sides that will be joined together at this time FF RO gt DEereuh QZmMAOG RY mme mgro Prrreu 14 You can get this game at www magic play eu You can get this game at www magic play eu WY QD 3 n i QD mD O QD a om Cc O O a Un WY Wi D 2 O O Cc O il qe OQ
9. much time to be idle between its attract time 6 Red Seconds 3 1 10 1 Seconds between Red lite Attempts During the game you can determine how much time to wait before lighting a clown red for the double point feature 7 Bonus Score 500 10 999 10 Bonus Target Score How much a player must score before achieving the bonus cloud 8 Bonus Tickets 100 0 999 25 Bonus Ticket Value How many tickets you win when you win the bonus cloud 9 Game Time 20 10 30 1 Time for Game Play How long the game lasts 10 Not Used 11 Not Used Options continued on next page 23 You can get this game at www magic play eu 12 13 14 15 16 17 18 19 20 21 You can get this game at www magic play eu Red Zone Tickets 1 0 20 1 JFP Tickets Sets the amount of tickets to win when 0 to 40 points are scored See Score chart below Also is used for giving tickets just for playing Orange Tickets 2 1 250 1 Tickets for Zone Sets the amount of tickets to win when 50 90 points are scored See Score chart below Yellow Tickets 3 1 250 1 Tickets for Zone Sets the amount of tickets to win when 100 190 points are scored See Score chart below Green Tickets 4 1 250 1 Tickets for Zone Sets the amount of tickets to win when 200 290 points are scored See Score chart below Blue Tickets 5 1 250 1 Tickets for Zone Sets the amount of tickets to win when 300 390 points are scored See Score chart below Indigo Tickets 10 1 250 1 Tickets for Zone
10. of the stars Attach the sign using 4 20x1 kep nuts Step 27 NISUS DE NEN ON GABNIVAL 1J CRNI Classics i b al E I j 20 You can get this game at www magic play eu You can get this game at www magic play eu Final Step Attach the data cable at the back of the Marquee Tuck the cable under the canopy on the left side of the game and down the front side of the cage Do not run it down on the right cabinet There is no wire ac cess hole It will be necessary to remove the front screw if attached It will be easier to slide the control panel out of the way by removing the mounting bolts This will allow easier access to the wire access hole See Step 9b On the main board are two phone style connectors You can plug in either of them Now run the AC cord from the back of the marquee to a wall outlet mI gite il eats i P ti unt M pig pg gig n ogg TNT I La LL LE T La ee eet er al D mi m i a vst tl f t A IM i Hm at M MT HT I Sas 288 i HT Jr pem ee TRAIT mm qu apt d TRE L EGO 48 LETT Er ii STILLET Herr m y lis 21 You can get this game at www magic play eu You can get this game at www magic play eu Game controls and Meters Located on the center door is the operators control panel There you can quickly adjust the volume of the game by pressing the UP a
11. ACLE TO BE SURE THE GROUND IS FUNCTIONING PROPERLY THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE OF THE GAME IF THE A C GROUND DOES NOT WORK THE GAME COULD DISCHARGE STATIC ELECTRICITY THROUGH THE GAME CIRCUITRY WHICH COULD CAUSE DAMAGE THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE TO OPERATE THE GAME AT VOLTAGES OTH ER THAN THOSE IT WAS DESIGNED FOR PLEASE CONTACT OUR SERVICE DEPARTMENT FOR VOLTAGE CONVERSION INFORMATION WARNING DO NOT remove any of the components on the main board e g compact flash and eproms while the game is powered on This may cause permanent damage to the parts and the main board Re moving any main board component part while powered on will void the warranty ALWAYS REMOVE POWER TO THE GAME BEFORE ATTEMPTING ANY SERVICE UNLESS NEEDED FOR SPECIFIC TESTING FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS THIS GAME IS NOT SUITABLE FOR INSTALLATION IN AN AREA WHERE A WATER JET COULD BE USED This appliance is not intended for use by persons including children with reduced physical sensory or men tal capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance AC Power Information The games main fuse is accessed through the bac
12. You can get this game at www magic play eu anm 2e 5 x zm LECC a eco teo reU 70 am C ARAN lucum gt Ia Fre V Cem hane VEZE a E jl EST EAs DOUBLE BOKSE Innovative Concepts in Entertainment 10123 Main Street Clarence NY 14120 You can get this game at www magic play eu You can get this game at www magic play eu 2 You can get this game at www magic play eu You can get this game at www magic play eu Table of Contents oafety Warnings and Power Requirements 4 Hardware 9 Setup 6 20 Program Settings 21 24 Bonus Suggestions and Ticket suggestions Error Codes 25 Quick Troubleshooting tips 26 Ball Gate Repairs 21 30 Control Panel Repairs 31 Clown Reset Shelf Repair 32 Spares 33 35 Warranty 36 Rev G 8 29 2014 3 You can get this game at www magic play eu You can get this game at www magic play eu SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING WHEN INSTALLING THIS GAME A GROUNDED A C RECEPTACLE MUST BE USED FAIL URE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS FAILURE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION OR DAMAGE TO THE ELECTRONICS NOTE THIS GAME IS INTENDED FOR INDOOR USE ONLY DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REASON AS GIVEN ABOVE USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WAR RANT Y HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A C RECEPT
13. c using 8 32 1 AA6177 screws I SSS See EE til SIL ez 135 42311 4 1 7 7 Pr ji sr ete TASA 3 wc EE Se ms A CERE EEGE WWE Ze GN M MEE imm eee e ae Lid d JJ Wee Be We Bre are we d 3 di za a 1 p WIL Hem Tm dili Min tec er j ml if iih yj gif gg it jj i A ei ci TAT gl il p 2 DE iini inis MEUM TUT eT gt daf eel al ee ae ie W W Mal s 5 Wis Step 25 Attach the Front trim and Pure Skill Plaque using provided square screws SRE 0 0E AM mE MIC T TUM TT Zz a Wil a i zm I tt L LET a sr VA 3 EC CC ERRER TR iil j TT il TIT ill jl A ii J4 You can get this game at www magic play eu You can get this game at www magic play eu Step 26 Attach the small red plastic trim pieces with one 1 screw through the front p E N 5 E N E i j y mudo Remove the graphic front by first removing the two 14 20 1 6211 bolts on either side
14. in materials and workmanship for the period listed below m 180 days on Main PCB s Computers amp Motors m 1 year on all LCD monitor panels m 90 days on all other electronic and mechanical components m 30 days on all l C E repairs and parts purchases C E Inc shall not be obligated to furnish a warranty request under the following conditions m Equipment or parts have failed through normal wear and tear m Equipment has been subjected to unwarranted stress abuse or neglect m Equipment has been damaged as a result of arbitrary repair modification Products will only be covered under warranty by obtaining an I C E authorized RMA To obtain an RMA please provide I C E tech support with the game serial or original C E invoice and a detailed description of the failure or fault symptoms Il C E Inc will assume no liability whatsoever for costs associated with labor or travel time to replace defective parts All defective warranty covered components will be replaced with new or factory refurbished compo nents equal to OEM specifications Il C E Inc will cover domestic UPS ground or comparable shipping costs during the warranty period Interna tional or expedited shipments are available for an additional charge To obtain credit defective parts must be returned to I C E Inc at the customer s expense within 30 days After 30 days a 15 re stocking fee will ap ply to all returns ICE distributors are independent priva
15. k of the game at the power mod Above the power cord is a small panel that contains the main fuse The value of the fuse for 120 volt users is 2 5 AMPS at 250Volt type slow blow The value of the fuse for 230 users is 2 5 AMPS at 250Volt type slow blow 4 You can get this game at www magic play eu You can get this game at www magic play eu STOP Before you begin to assemble your game locate the parts box and ensure all parts are present If any parts are missing please contact ICE Service at 716 759 0360 Mon Fri 9am to 6pm Eastern Standard Am it P S Partt AA6799 Part AA6444 20 Screws 16 Joint Part AA6281 Part PC60601 Cage amp Poles Connectors 1 Poles Screws 5 8 Sides for Cage Sides 4 Marquee 2 Red amp Yellow Header Part AA6369 2 Front of Cage 2 3 1 2 Bolts for Cage Red HDPE at bottom a ASA Part AA3052 Ea A 9 4 Hole Plugs S MONS Lo ANS Ober f for Cage Red Part AA6289 HDPE Rear Cabinet Part AA0655 a Self j 4 Screws Tapping Screws for for Plaques Canopy PUN Part Down art AA6075 c 2 Marquee PC60614 E the 1 Jd 2 Rebound Parti iae N 3 Clown Guard Poles PC60604 2 Marquee IB Hardware piden 2 Rebound gt Box or Chea Sensor Q Part AA60601A 5 32 Allen Wrench 1 piece Part AA6001B 3 16 Allen Wrench 1 piece Part AA6603 3 32 Allen Wrench 1 piece
16. n Support Arms can swing and cause injury when not fully attached Ly TM Bek USA UN ACA RR ER Vo LI TILILI FF s Note Attach the upper braces first using 1 4 20 x 1 1 2 bolt and 1 4 20 keep nut Then side the bracket for the cheat sensor on the bolt and attach with another 1 4 20 kep nut The wire harness attaches to the upper brace with a tie wrap down the right side to the front of the cage down the cage front and into the wire access hole shown in step 9b It connects to the main board shown 10 You can get this game at www magic play eu You can get this game at www magic play eu Step 8 Attach the bonus sign to the top of the cabinet using four 14 20 1 7 8 AA6799 bolts and washers as shown Plug the sign harness through the back Attach the two harness on the right and one on the left Tilt the top of the bonus marquee forward when installing Step 9 Position the canopy onto the top of the cabinet Lift the side slightly on the canopy to expose the mounting flap with pre made holes Front of cabinet has reinforced holes for front mount Use the self tap screws to attach the canopy to the cabinet Do not screw through the outside of the canopy 11 You can get this game at www magic play eu You can get this game at www magic play eu Step 10 STOP if installing two games with Mega Marquee skip to step 13 If you are going to use the Mega bonus sign do not install thi
17. nd DOWN push buttons You can view how many coin pulses the has seen and how many tickets it had paid out To adjust the game s programming press the PROG button to en ter programming The SELECT push button will cycle through the different options Pushing the UP push button will increase the options value while pressing the DOWN push button will decrease the options value It is recommended to use our suggestive settings when configuring your game Please review the next few pages before determining your settings 22 lt s5 4 E id p ji A ini ap s l pr Lr ede LT ER TIR LF You can get this game at www magic play eu You can get this game at www magic play eu Programming Options for Down Da Clown Seconds Display Blank Value Option Number Option Default Min Max Inc Short Description 0 Game Volume 5 0 7 1 Game Volume This option adjusts the general game sounds 1 Music Volume 3 0 7 1 Music Volume This option adjusts the music in the game and attract mode 2 Coin 1 1 0 10 1 Cost of Game How many pulses to start your game 3 Coin 2 1 0 10 1 of Coin 1 s This pulse is equal to the cost of the game Use as a multiplier for credits 4 DBV 4 0 10 1 of Coin 1 s This pulse is equal to the cost of the game Use as a multiplier for credits 5 Attract Time 0 0 90 1 Attract time This options determines how
18. ou should also run the phone cord at this time It will be needed in the final step PTI po E EZ ES poi f CC T R T h EEEE EEEE EEEE TEEGA E EI LEEBELEEEL LAELCSCU TL 17 You can get this game at www magic play eu You can get this game at www magic play eu Step 22 Slide the two cabinets together tilt the Mega Marquee back a little and insert the bottom of the Mega Marquee into the cabinet slots as shown ul 4 Tem T 7 VE D 2 PE f allt LSE ANS E Step 23 Insert the canopy flaps into the top slots of the marquee Attach the marquee to the cabinet cages using 1 4 20x24 bolts Attach the rebound guards at this time See step 11 for instructions 1 ea ie M i Mo Y 2 En COD x XN es bee 3 z ar Ha B B NN ii ifi Zu CM oe fi MU p 2 jii ii ES G S um X 4 it til fl os S iim y t Tu A iiy You can get this game at www magic play eu You can get this game at www magic play eu Step 24 Attach the center graphi
19. plastic bracket Attach connector and plug in Order part E02907BLX You can get this game at www magic play eu You can get this game at www magic play eu Spare Parts List ASY COIN DOOR O U BLACK W DUAL ICKET DOOR OCK 7 8 CAMLOCK 45 DECAL COIN DECAL TICKET PEAKER ROHS 6X9 U694 W HINGE TARGET TOP HINGE TARGET MIDDLE HINGE TARGET BOTTOM AGE SIDE LEFT AGE SIDE RIGHT AGE CONNECTOR DEFLECTOR LED BALL ENT POLE REAR ENT POLE FRONT RACKET TARGET RESET RACKET FRONT SHELF SUPPORT AM TARGET RASS GROMMET INKAGE TARGET RACKET LED MOUNT SHELF TOP RACKET LED MOUNT SHELF MIDDLE RACKET LED MOUNT SHELF BOTTOM MOTOR ARM HARACTER MOUNT LYING CHARACTER HARACTER MOVING BLOCK RACK STANDOFF DLER PULLY MOTOR ARM PIVOT RACKET CANNON PRING ASY CHEAT SENSOR ASY POWER MOD 2 5 AMP CBA DISPLAY 2 DIGIT CBA I O CBA RESISTOR BOARD HARNESS MAIN HARNESS DC POWER HARNESS SCORE DISPLAY HARNESS BONUS SCORE DISPLAY HARNESS CLOWN SENSOR EXTENSION HARNESS CLOWN SENSOR HARNESS BALL GATE ZERO COUNT HARNESS BALL GATE MOTOR SENSOR HARNESS SHELF MOTORS EXTENSION HARNESS SHELF MOTORS HARNESS CLOWN RGB LED EXTENSION 34 You can get this game at www magic play eu E II SIH AITO WIDIWIT WION Wi Wi MIAO Un LH Ao Z Z m unu unu Colles CIO Z Z CIC NiN SE Nin re E gt gt JE IE r1 Er JE 7 ey Tj You can get this game at www magic play eu
20. s sign Otherwise remove the eight screws holding the sign together that are on the front of the sign graphic side Put the sign and hardware aside Step 11 Located inside the cabinet you will find the cable attached to the upper side of the cabinet Remove the bolts holding the control panel so you can slide the panel to expose the access hole that the marquee wire will travel through Route the wire through the cage and up to the sign Attach with wire ties AUS v pass ha T TT UT n s ATTI I D l HITNI Th so TTY IT i d T TM Vit rel is n 1 IIT E Lm nm I I mm Mpp tay te IT Jj I ALL Tae SEU B IIT SLITT 5 LIN i Ski I Ar 4 TW A sg ed lf IS bola P Woe T Wee n I T J 2 N nu 7 IT TIT LOT e Sail i B T ITA T J IM M ae agmini d 12 You can get this game at www magic play eu You can get this game at www magic play eu Step 12 Connect the wire harness before attaching the sign Use two 4 20 PC60614 kep nuts to attach the sign to the upper support bar The bolts are already present Reattach the sign with the hardware you put aside Install only in the bottom hole Step 13 Attach the left and right plastic front covers using 1 4 20 3 AA60636 bolts Do not install any bolts at the bottom Do not over tighten The rebound guard attaches there See step 14
21. tely owned and operated In their judgment they may sell parts and or accessories other than those manufactured by I C E Inc We cannot be responsible for the quality suitability or safety of any non lI C E part or modification including labor that is performed by such a distributor Innovative Concepts in Entertainment 10123 Main St Clarence NY 14031 Phone 716 759 0360 Fax 716 759 0884 WWW icegame com 37 You can get this game at www magic play eu
22. tom Row switch not seen Solution Check Clown Reset Bracket sensor See section Clown Reset Bracket Sensor To enter Error display mode please press the UP push button located on the lower center door when in attract To exit this mode repress the UP push button 26 You can get this game at www magic play eu You can get this game at www magic play eu Cannon Failure Clown doesn t travel out of the cannon If during power on if the home switch is not made the clown will not exit the cannon Ensure both the home switch and end of travel switch are functioning properly Quick Check list 1 Checkhome switch has no voltage on it when homes clown inside the cannon Use J16 pin 2 on the main board Use pin 8 for ground 2 Check for 5 on End of travel switch when in home position Use J16 pin 7 Mega Sign Shows 111 Phone Cord not plugged in or no communication to main board Canopy peak doesn t line up Long canopy support bars are installed in the front Reverse support bars short to the front No display on Upper Bonus Marquee Check connections at the left of cabinet 27 You can get this game at www magic play eu You can get this game at www magic play eu Ball gate Assembly Step 1 Ball gate Removal Remove the wood panel ball gate cover as shown The cages canopy support bars and rebound have been removed for clarity Step 2 Ball gate Removal Remove three woodscrews on each side as sho
23. wn below Remove these screws on both sides Step 3 Ball gate Removal Loosen the 5 64 Allen set screw Lift the ball defectors 28 You can get this game at www magic play eu You can get this game at www magic play eu Step 4 Ball gate Removal c e3 a eE w D 2 O c D cc z 9 QD Q c z O ce Y D Wi o gt e3 Ke 42 QD Q O eb ie ras O Y Q eb Y Uu w Y o0 Q QD za ras 2 O Ea Y lt a Y Y z D Cam QO Y O O O z O Q O z 4 2 D D i QD C Step 5 Ball gate Removal Lift the ball gate straight up and unplug the wire harness before lifting the ball gate assembly out 29 You can get this game at www magic play eu You can get this game at www magic play eu Step 1 Motor Removal REMOVE BALLGATE ASSEMBLY BEFORE PROCEEDING Flip the ballgate assembly over and remove the four Allen screws and lock washers shown Step 2 Motor Removal Removal the Screw that holds motor shaft to the ball deflector shaft This screw has Loctite applied to it and could be difficult to remove Le Step 3 Motor Removal Step 4 Motor Removal Loosen the grub screw that holds the motor cam shaft to the motor This grub screw also has Loctite applied to it and could be difficult to loosen Lift the cam shaft off Remove the two screws that hold the motor to the motor mount
Download Pdf Manuals
Related Search