ReadyLift (Part# 69-3285 and 69-3485) New Body
Contents
1. steering and related components When selecting combinations larger than OE consider the additional stress you could be inducing on the OE and related components 4 Post suspension system vehicles may experience drive line vibrations Angles may require tuning slider on shaft may require replacement shafts may need to be lengthened or trued and U joints may need to be re placed 5 secure and properly block vehicle prior to installation of ReadyLift Suspension Inc components Always wear safety glasses when using power tools 6 If installation is to be performed without a hoist ReadyLift aSuspension Inc recommends rear alterations first 7 Due to payload options and initial ride height variances the amount of lift is a base figure Final ride height dimensions may vary in accordance to original vehicle attitude Always measure the attitude prior to begin ning installation POST INSTALLATION WARNINGS 1 Check all fasteners for proper torque Check to ensure for adequate clearance between all rotating mobile fixed and heated members Verify clearance between exhaust and brake lines fuel lines fuel tank floor boards and wiring harness Check steering gear for clearance Test and inspect brake system 2 Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating mobile or heated members Inspect rear brake hoses at full extension for adequate slack Failure to perform hose check replacem2. 70mm 4WD Only M12 Socket Cap 80mm 4WD Only M12 Flange Nut 4WD Only M12 Socket Cap 35mm 4WD Only M12 Socket Cap 45mm 4WD Only M12 Fender Washer 36mm O D M12 1 75 35mm Hex Head Bolt Class 10 9 ZP M12 Split Lock Washer M12 Flat Washer Skid Plate 4WD Only M10 1 25 30mm Flange Head Thread Forming Bolt 4wp only 3 Tapered Block w Axle Pad Ears 4WD Only Square U bolt M14 1 5 Barrel Nut M14 Thick Washers Rear Shock Extension M14 2 0 75mm Hex Head Bolt Class 10 9 ZP M14 Washers M14 2 0 C Lock Nut 8 Black Zip Ties Tools Needed Metric Socket Set 10mm 22mm 1 2 Ratchet Adjustable Wrench Floor Jack Jack Stands Transmission Jack or attachment for floor jack Metric Allen Wrench Set Metric Combination Wrench Set Pry Bar 4 1 2 Angle Grinder with Flap wheel Thread Locker Vice Hammer amp RP BH PD VD CO CO HD WS a NA ANa DN ONY P POM NY NN ND a ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10 RIEAN oe ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Remove the front wheels Unbolt the five 15mm bolts t
3. Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Wheel Alignment a Certified Alignment Technician that is experienced with lifted vehicles is recom mended to perform the alignment It is recommended that you have your vehicle s alignment checked whenever installing suspension parts Vehicle Handling Warning Installation Warning Vehicles with larger wheels and tires will handle Always wear proper safety equipment and use the differently than stock vehicles correct tools when installing any suspension up grade Make sure vehicle is on a flat surface and Take time to familiarize yourself with the handling ff you are using jack stands or a lift rated for the of your vehicle weight of the vehicle Warning 69 3285 and 69 3485 kits are designed and engineered to lift a stock vehi cle with no prior modifications The use of these kits along with items such as rear lift blocks or spacers add a leafs airbags suspension lifts body lifts or any other type of lifting accessory shall be done at the vehicle owners risk and will void any and all warranties in effect or implied by ReadyLift ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10
4. BEANE J 5 SUSPENSION INC ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions SAFETY WARNING ReadyLift Suspension Inc recommends this system be installed by a professional techni cian In addition to these instructions professional knowledge of disassembly reassembly procedures and post installation checks must be known PRODUCT SAFETY WARNING Modifying your vehicle ride height may result in the vehicle handling differ ently than a factory equipped vehicle Extreme care must be used to prevent loss of control or vehicle rollover Failure to drive your modified vehicle safely may result in serious injury or death ReadyLift Suspension Inc does not recommend the combined use of suspension lifts body lifts or other lifting devices You should never operate your modified vehicle under the influence of alcohol or drugs Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions Always wear your seat belt Pre Installation Notes 1 Special literature required OE Service Manual for model year of vehicle Refer to manual for proper disas sembly reassembly procedures of OE and related components 2 Adhere to recommendations when replacement fasteners retainers and keepers are called out in the OE manual 3 Larger rim and tire combinations may increase leverage on suspension
5. ELY CAREFUL NOT TO STRIP THE HOLES IN REAR INSTALLATION THE FRAME LIGHTLY TIGHEN WITH HAND TOOLS Position truck on a flat surface and lift vehicle by the frame so that the rear wheels are off the ground Use a minimum 3 ton jack stands and place under frame for safety or a use two post lift if available Make sure that the front wheels are blocked to prevent a rollout 46 Install the Readylift skid plate using the M10x30mm self tap ping bolts provided into the existing holes in the front and rear cross members Support the axle with a floor jack or pole stand Remove the passenger side rear shock with a 21mm socket and wrench Unhook the ABS line located behind the rear bump stops on the underside of the frame on both sides Revised ReadyLift Suspension Inc 7 27 40 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIEAN oe ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Using a 21mm socket to remove the factory u bolt nuts axle plate and u bolts on the passenger side only Install the ReadyLift 3 block with the shorter tapered side facing the front of the vehicle Raise the
6. axle make sure the provided Tighten to 136lb ft leaf spring center pin goes in the hole on top of the block Install the new u bolts factory axle plate washers and nuts Install the ReadyLift rear shock extension on the upper mount Install the shock extension into the upper mount using of the shock using the M14x70mm bolt M14 washers and M14 the factory bolt Do not tighten C Lock nut provided Tighten to 136 lb ft Revised ReadyLift Suspension Inc 7 27 10 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIEAN 4 oe ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Lubricate the ABS line with WD 40 and slide the rubber sleeve up to allow the wire to be reinstalled in the clip on the frame Siw You may need to bend the upper and lower brake line brack ets to allow enough slack in the line at full droop Revised ReadyLift Suspension Inc 7 27 10 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIENDA J 5 SUSPENSION INC ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4
7. d Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10 RIEAN oe ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended me a Put the cross member back in place Use of a rubber mallet may be needed to help persuade the cross member mounting holes to line up Install the factory hardware the head of the bolt should face Install the ReadyLift Strut Extension on top of the strut using the rear and the nut should face the front Tighten to 75 ft lb the factory hardware Tighten to 45 lb ft Install the ReadyLift upper control arm The upper ball joint Re install the strut into its stock location Loosely install the will be angled towards the rear of the vehicle Install the cam M10 flange nuts on the upper mount bolts and cams Line up your markings ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10 RIEAN oe ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before begin
8. e of the differential Remove the passenger side torque arm using a 15mm socket Remove the two M12 press in studs and 18mm socket Revised ReadyLift Suspension Inc 7 27 10 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIENDA J1 ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended ae Bolt the 2 wide diff drop bracket narrow taper facing the rear Reinstall the torque arm to the frame mount Torque the fac to the torque arm using the M12x70 and M12x80 socket cap tory hardware to 75ft Ib bolts and M12 flange nuts 75ft Ib i if Install the driver side differential drop bracket using the Raise the differential back up into its mounting location Take M12x40 and M12x45 socket Cap bolts Tighten to 75ft lb care not to pinch the electrical line 30 fender washers on the passenger side mount Install two Reconnect the tabs from the wiring harness and plug the con M12x35 bolts split lock washer and flat washer on driver side ector back in mount Tighten to 85 Ib ft Loosely install two M12x35 bolts split lock washers and ReadyLift Suspension Inc 3201 W MacArthur Blv
9. ent may result in component failure Longer replacement hoses if needed can be pur chased from a local parts supplier 3 Headlight adjustment is highly recommended 4 Re torque all fasteners after 500 miles Always inspect fasteners and components during routine servicing Revised ReadyLift Suspension Inc 7 27 40 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 BEANE J 5 SUSPENSION INC ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground Use a minimum 3 ton jack stands and place under frame for safety or a 2 two post lift if available Make sure that the emergency brake is on and the rear wheels are blocked to prevent a rollout Bill of Materials Description QTY Description QTY Upper Control Arm w Ball Joint Driver Side 1 M10 1 25 55mm Hex Head Bolt 10 9 4 Upper Control Arm w Ball Joint Passenger Side M10 Flat Washer 8 Ball Joint Zerk Fitting M10 1 25 C Lock Nut 4 Cotter Pin Castle Nut M6 Flat Washer M6 Nyloc Nut UCA Bushings Black UCA Crush Sleeve UCA 45 Degree Zerk Fittings Strut Extension M10x1 25 Serrated Flange Nuts Differential Relocation Bracket 1 Wide Driver Side 4WD only Differential Relocation Bracket 2 Passenger Side 4wp Only M12 Socket Cap
10. hat Unclip the ABS line at the upper control arm pocket on both hold the plastic air dam on Set aside sides Unclip the ABS line at the upper control arm and unbolt the Remove the sway bar end link bolt using a 15mm socket and brake line retention bracket on both sides a 15mm open end wrench Do this on both sides Remove the brake caliper using an 18mm socket Secure the Unbolt the tie rod end using a 21mm socket A additional caliper so that the brake line does not get stretched or dam f wrench may be need to keep the ball joint from spinning Re aged Repeat on opposite side peat on opposite side ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10 BEN ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Remove the six 15mm axle shaft bolts Set the hardware Separate the upper ball joint from the steering knuckle Re aside as it will be reused Repeat on opposite side peat on opposite side Mark the position of the alignment cams Remove the 21mm UCA nuts cams and bolts Revised ReadyLift Suspension Inc 7 27 10 3201 W MacArthur Blvd San
11. ning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended ae M _ Raise the lower control arm and line up the lower mounts Tighten the three upper strut mounting nuts to 45 ft lb Install Install the M10x55 bolts washers and nyloc nuts Tighten to the upper ball joint to the knuckle Tighten to 85 ft lb Install the supplied cotter pin Install the front brake calipers using the factory hardware and 18mm socket Tighten to 146 lb ft Re install the front driveshaft using the factory hardware and Reconnect the inner CV shaft using the factory hardware clamps Tighten to 26 ft lb Tighten to 45 ft lb ReadyLift Suspension Inc 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 Revised 7 27 10 RIENDA J 5 ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Reconnect the ABS line and place back in factory location Install the brake line support bracket onto upper control arm Reinstall the sway bar end links on both sides Tighten to 45 using the 6m nuts and washers provided Tighten to 7 lb ft lb ft BE EXTREM
12. ta Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIENDA J5 ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended Disconnect the blue electrical plug from the front differential Support the front differential with a transmission jack Remove the two passenger side mounting nuts Remove the rear cross member and set aside Revised ReadyLift Suspension Inc 7 27 10 3201 W MacArthur Blvd Santa Ana CA 92704 Toll Free 888 922 2294 Fax 714 862 2972 RIEAN 4 Se ReadyLift Part 69 3285 and 69 3485 New Body Chevrolet GMC Silverado Sierra 1500 6 Lug 2 amp 4WD 4 Lift Kit Installation Instructions Please read instructions thoroughly and completely before beginning installation Check www Readylift com for any updated installation instruction Installation by a trained mechanic is recommended ZO pa Breather Hose Unplug the breather hose Remove the driver side mounting bolts Make sure the differential is secured with the transmis sion jack Slowly and carefully lower the front differential down to the floor Use a black permanent marker to mark the material to be re moved This will be on the driver sid
Download Pdf Manuals
Related Search