FBR-BK - Arrow International, Inc.
Contents
1. then the SHOW STATUS key RELORDELA Ltt t AUDIO HEME f LLOUK l SEIUH l SETUP DYNAMICS SETU Fiber Optic Sensor Status Codes FOS electronics and sensor are None e None working properly and ready for use NO COMM No communication between CPU System error 8 e FOS PCB failure and FOS electronics e FOS PCB or CPU cable disconnect e Loss of power to FOS PCB e CPU failure Low light return AP FOS weak e Sensor not fully connected signal e FOS cable is damaged or broken e Connections are dirty e Connection is damaged e FOS board failure Strong light AP FOS signal e Sensor not properly connected out of range e Connections are dirty e Connection is damaged CAL key missing or data are corrupt AP FOS CAL key e CAL key not connected missing or corrupt e CAL key data corrupt e Ribbon cable loose or disconnected m rr Es O A FOS electronics outside of operating AP FOS signal e FOS warming up at start up temperature out of range e FOS heating circuit failure e Loss of power to FOS electronics e Air conduit blocked FOS is measuring barometric pressure AP FOS signal e Altitude exceeds 8000 ft outside of operating range out of range e FOS electronics failure Ratiometric error e Incorrect calculations e CAL key may be damaged or corrupt e Possible FOS PCB failure FOS is measuring outside of pressure AP FOS signal e Excessive pressure on sensor range out of range e Sensor has been damaged Instrument error System err2. DO NOT FORCE the connection Pull the slide connector back slightly and re attempt the connection Generally the connection is made on the first or second attempt Once the IAB Is inserted into the patient and connected to the IABP system the fiber optic cable should be taped to the driveline tubing in several places If conditions do not allow for zeroing the sensor prior to insertion then insert the IAB and proceed to the AP Fiber Optic Sensor Calibration section if needed NOTE The WAVE timing algorithm will perform properly whether the FOS is zeroed or not However the accuracy of the sensor s numerical values and wavetorm may be affected by not zeroing the sensor prior to insertion similar to not zeroing a transduced fluid filled AP source AP Fiber Optic Sensor Calibration In some cases it may not be possible to zero the FOS prior to insertion This may result in less accurate hemodynamic values for the AP signal similar to when a fluid filled trans ducer is not zeroed Since the FOS cannot be zeroed once the IAB is inserted into the patient a method to adjust the AP values is available The FOS calibration function allows the user to adjust the MAP value to another MAP value which is known to be accurate To perform this calibration press AP SELECT and verify FIBER OPTIC is selected Press the FOS MAP CAL function key This will display the current MAP value that is being displayed by the FOS Verity that the MAP fr
3. FiberOptix AP Sensor aera Zeroing and Calibration Guide AN ARROW INTRA AORTIC BALLOON i lt Oe TRAE LORE UECEP i 2 1 800 447 IABP 4227 Se Worldwide 617 389 8628 Caution U S Federal Law limits this device to sale by or on order of a physician Contents of unopened undamaged package are sterile Disposable Refer to package insert for current warnings indications contraindications precautions and instructions for use U S Patent Nos 6 258 035 6 569 103 and 6 887 206 Distribution Worldwide Arrow offices are located in Belgium Canada Czech Republic France Germany Greece India Italy Japan Mexico Netherlands Slovakia South Africa Spain and the United States Arrow International Inc 2400 Bernville Road Reading PA 19605 U S A Tel 610 378 0131 AN ARROW www arrowintl com CARDIAC ASSIST A x FBR BK 3 06 CRB 06 0070 Ara Eh 2006 Arrow International Inc All rights reserved Printed in the Czech Republic Arterial Pressure AP Fiber Optic Sensor FOS Zeroing There are 2 ways to zero the fiber optic sensor on the FiberOptix intra aortic balloon IAB manually and automati cally For either zero procedure the blue FOS slide and black CAL key must be connected to the pump prior to IAB insertion Connect blue sensor and CAL key PRIOR to insertion This is the only time the sensor will be exposed to atmos pheric pressure In an emergent situation where the ze
4. dirty or damaged Chapter 10 of the service manual e Replace FOS track assembly e Call Field Service CK CAL key not connected e Connect CAL key or corrupt e Disconnect then reconnect CAL key e Replace IAB e Check cable connected to rear of CAL key front panel connector e Replace IABP e Call Field Service FOS does not zero TL FOS electronics are e It may take up to 5 minutes for the message to clear outside of operating e Insert IAB without zeroing use FOS MAP CAL function if temperature range numerical values are not accurate e Call Field Service LT Calibration table loading or e Wait up to 20 seconds for calibration data to load loading error e Remove and reconnect CAL key e Replace IAB e Exchange IABP console e Call Field Service if problem occurs No FOS waveform is displayed or completed correctly waveform is off screen L Broken or damaged cable e Replace IAB e Use alternate AP source PL Sensor damaged or e Use FOS MAP CAL function if numerical values are not accurate improperly zeroed e Replace IAB e Use alternate AP source No FOS waveform PL Sensor damaged or e Use FOS MAP CAL function if numerical values are not accurate is seen and improperly zeroed e Replace IAB numerical values e Use alternate AP source are gt 350 mm Hg or lt 0 mm Hg FOS signal lost LL FOS cable damaged or e Replace IAB signal was broken e Use alternate AP source present but is no longer displayed LL FOS not connected or e Remove blue slid
5. e then reconnect partially connected e Verify 2 clicks and audible tone are heard e Use alternate AP source e Replace IAB NOTE If the IAB is in the patient with first zeroing the light bulb will remain blue but the waveform should appear if the sensor is functional If needed follow the steps in the AP Fiber Optic Sensor Calibration section to adjust the fiber optic sensor MAP values FOS light bulb Current sensor has been e f IAB is not inserted insert another CAL key when light bulb turns green in connected and zeroed changes to blue disconnect CAL key and re insert the CAL key lt 10 seconds or prior or sensor did not that is attached to the IAB Sensor should zero properly on connection zero correctly of a new IAB sensor
6. om another AP source is accurate Use the lt or gt keys to adjust the MAP value This is an active adjustment no confirmation key press is required NOTE Once this calibration is completed it is generally not required again Fiber Optic Sensor Diagnostics The following sections provide detailed information on specific issues with the fiber optic system Status mes sages or codes may be viewed by the operator during the course of therapy and provide information relative to the current operational status of the fiber optic electronics connections and sensor A description of the code possible alarms associated with that status code and the issues that may result in the code being displayed are shown The Fiber Optic Message Guide also reviews possible symptoms related status codes causes and recommended actions In all cases if the fiber optic system is or becomes non operational an alternate AP source will automatically be selected by AutoPilot If Operator mode is selected an alternate AP source needs to be selected by the user NOTE The loss of the fiber optic signal does not impair functionality of the IABP system Fiber Optic Sensor Status Codes This section details the status messages that are issued by the fiber optic system They are designed to verity the current FOS status and assist in providing specific informa tion for identifying and resolving FOS issues To view the code press the HOME key
7. or 8 e Unknown error or no alarm Excessive offset Zeroing procedure None e Zero was not completed properly or resulted in a large difference from occurred when the sensor was disconnected factory set calibration or partially connected Loading calibration table None e f it goes away within 10 seconds no problem e f it stays longer and the zero does not complete the key may be damaged or corrupt or the ribbon cable may be disconnected Sensor zeroing None e None unless longer than 1 minute see FOS does not zero in the Fiber Optic Sensor Message Guide Communication failure System error 8 e FOS electronics failure ST Self test Ongoing self test that does System error 8 e FOS electronics failure not complete w as V ar E Fiber Optic Sensor Message Guide This section discusses messages that may occur when using the fiber optic system The expected or related FOS status code is shown potential causes are detailed and recommended solutions given Some actions may be done by the user Those items shown in talics should be performed by qualified service personnel Fiber Optic Sensor Messages FOS does not zero LL Sensor not fully e Remove blue slide then reconnect connected e Verify 2 clicks and audible tone are heard sensor should zero within 1 minute LL Sensor cable damaged e Use alternate AP source or replace IAB or broken LL Sensor interface block e Clean FOS connector using procedure recommended in is
8. ro procedure cannot be performed due to a deteriorating patient condition insert the IAB in the usual fashion and initiate Support Later manual calibration can be performed as described in the AP Fiber Optic Sensor Calibration section Manual Zero To perform a manual zero with the connections made verity FIBER OPTIC is illuminated next to the AP SELECT key and press the soft key under FOS ZERO The blue light bulb on the screen will turn green when the zero is completed A message at the bottom of the screen will also be present to confirm the zero Automatic Zero The AP FOS can automatically zero when the following conditions are present 1 FOS connector and CAL key are connected 2 Data from CAL key has been downloaded to intra aortic balloon pump IABP 3 No AP waveform is detected 4 The fiber optic electronics have reached the normal operating temperature NOTE The AP FOS will automatically zero even if FIBER OPTIC is not first selected Prior to any connections the following message will be displayed when the AP SELECT key is pressed and FIBER OPTIC is illuminated Connect fiber optic sensor and CAL key Zero prior to IAB insertion It does not matter which connection is made first the CAL key or the blue slide housing the FOS However it is important to ensure the fiber optic connection is made securely by listening for 2 clicks as the connection is made NOTE If resistance is met during connection
Download Pdf Manuals
Related Search