S10 motor mount instructions
Contents
1. again and check whether EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com the transmission shaft and clutch plate is mating properly Step 7 Once step 6 is completed successfully tighten the bolts up to lock the housing 1 Step 8 Place the top motor mount over the motor and align the center hole with the lifting hole on the motor lt Before installing the center bolt makes sure that you include a flat washer and a lock washer otherwise the bolt may damage the motor Step 9 Place 4 NC x 1 bolt in one end of the motor mount and using an aligning punch line up the second hole and insert the second bolt into the motor mount Step 10 Tighten the center bolt first followed by the two side bolts2. 35 512 9978 sales evsource com N a g s F Step 4 Place the hub otor shaft Apply Locktite on the 4 NC 20 socket head bolts and bolt the hub onto the taper lock hub Make sure the Bushing is up against the spacer while you tighten up the bolts In addition tighten the bolts equally a little at a time to slowly pull the hub onto the Bushing Step 5 Place the bell housing onto the motor and make sure the top of the bell housing is center with the lifting hole on the motor Apply Locktite on 0 0 0 0 0 0 00 LIVELL ZINAISZAIINI 0100000000 to varying adapter thickness and motor type your 3 8 bolts may be too long for your specific motor After threading one bolt through the adapter and EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com into the motor GENTLY turn the motor shaft and listen If the shaft is hard to turn or if you can hear some grinding remove the bolt immediately This sound or hard turning indicates that the bolt has gone so far into the motor as to be in a position to damage the motor fan when the motor really gets going Instead replace the bolts with a shorter one that does not interfere with the fan EV Source will not be responsible for this error Step 6 Place the flywheel onto the hub and using the original flywheel bolts bolt the flywheel onto the hub Make sure there is Locktite on the bolts Tighten the bolts in cris cross pattern and torque the bo
3. EV Source LLC 695 W 1725 N Logan UT 84321 Adapter Housing And Motor Mount Installation Instructions EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com 2 2 Motor Installation Required Hardware Tools e Torque Wrench Socket Sets Locktite Engine Hoist Allen Keys Components Aluminum Housing Taper lock Bushing Hub 2 2L 2 8L or 2 5L 3 8 Hub Spacer 9 Motor 34 Hub Spacer 8 Motor 4 3 8 NC x 1 bolts and flat washer Motor to Bell Housing 3 W NC 20 x 1 socket head bolts Taper lock Hub 6 NC x 2 14 bolts Bell Housing to Transmission EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com Do you have the transmission reinstalled If not reinstalled the transmission before continuing any further If the engine mount is for a V6 or 2 2L 4 cylinder engine replace the mount with 2 5L four cylinder engine mounts 2 2 1 Motor and Bell Housing Installation Instructions e Use the engine hoist to lift up the motor so you can install the components onto the motor easily VO Lai a Step 1 Place the hub s pacer onto the motorshatt EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com seats against the hub spacer i Step 3 Install 4 x 1 4 key into the keyway to lock the Bushing onto the motor shaft EV Source LLC 695 W 1725 N Logan UT 84321 4
4. lts according to the service manual specification Step 7 Place clutch disk and plate onto the flywheel and tighten the bolts according to the service manual specification Be sure to use a clutch alignment tool to center the disk EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com EV Source LLC 695 W 1725 N Logan UT 84321 435 512 9978 sales evsource com 2 2 2 Motor Mount and Motor Components e Motor Mount e 2 2 NC x 1 14 bolts Motor Mount e 1 5 8 NC x 7 8 Grade 8 bolt Motor to Mount Instructions Step 1 Place the bottom half of the motor mount between the engine mounts and reuse the two original bolts removed with the engine to lock the motor mount in place Step 2 Move the engine hoist with the motor to engine compartment Step 3 Lower the motor into the engine compartment until the bell housing is aligned with the transmission Step 4 Make sure the shaft from the transmission is aligned with the bore on the clutch plate Then slowly push the motor until the bell housing is touching the transmission Step 5 Place all 6 of the Y2 NC x 2 14 bolts and hand tighten the bolts Then lower the motor into the motor mount until motor rest completely on the motor mount Step 6 To test whether the shaft is binding turn the front shaft on the motor with your hand The shaft should rotate freely with some resistance If the shaft does not rotate freely lift the motor up
Download Pdf Manuals
Related Search