hp® p1006 cartridge remanufacturing instructions
Contents
1. CARTRIDGE REMANUFACTURING INSTRUCTIONS 18 Clean out all the remaining toner from the hopper Make sure the magnetic roller seals and the doctor blade seals are all clean 17 Remove the doctor blade and two screws NOTES 19 Fill the hopper with 100g P1006 toner A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 20 When a seal becomes available remove the seal port plug and install the seal Bring the tail out through the seal port hole Install the plug 21 Install the left side end cap and screw Make sure the small contact piece is installed correctly on the end cap A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 22 Install th2. All the error codes consist of different pattern of the two lights Information on the lights is very poor Even the service manual is terri ble TOP LIGHT BLINKING Cartridge door open no print cartridge installed or there is a paper jam BOTH LIGHTS ON Fatal error turn the printer off and unplug it for 30 minutes If the error still exists the printer has a major problem There is no information yet on what these problems may be The service manual has not been released yet BOTH LIGHTS BLINKING A printer initialization is in progress A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information
3. HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS HP P1006 LASER PRINTER HP P1006 TONER CARTRIDGE A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS REMANUFACTURING THE HP LASERJET P1006 SERIES TONER CARTRIDGE CB435A By Mike Josiah In November 2007 Hewlett Packard released the LaserJet P1006 printer The HP P1006 series of laser printers are based on a 17 ppm true GOOdpi Canon engine These cartridges use a chip that controls the toner low functions The CB435A is rated for 1 500 pages Physically the cartridges look like a small 12A 1012 cartridge but there are many differences The printer itself has a very small foot print It s a nice small office home machine The first page out is stated to be in under 8 5 seconds from a power save mode The memory is fixed and not expandable at 8Mb The recommended monthly volume is from 250 1500 pages month but the maximum monthly duty cycle is 5 000 pages Unlike many small printers these machines have an input tray that can hold 150 pages A nice touch The system that holds the t
4. NSTRUCTIONS NOTES 6 Remove the two screws and the wiper blade T7 Clean out all the waste toner from the hopper Be careful not to damage the recovery blade located next to the wiper blade If this blade is bent in any way the cartridge will leak Make sure the wiper blade foam seals are clean A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 8 Coat the new cleaned wiper blade with your preferred lubri 9 Install the cleaned PCR Place a small amount of conductive cant Install the wiper blade and 2 screws grease on to the black holder side of the shaft Just a small amount of grease is more than sufficient 10 Place another small amount of conductive grease on to 11 Install the new cleaned drum hub side first the metal drum axle 12 Place the waste drum section aside A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owner
5. e doctor blade and two screws 23 Install the magnetic roller black bushing side first Turn the roller until the keyed end locks in place 24 Install the gears as shown 25 Install the end cap and screws A TTT UniNet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 26 Place the drum waste hopper into the toner hopper Slide it over so the round hinge pins fit into their respective holes 2 Set the hopper tension springs back in place SUMAN TECHNOLOGIES 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 e Fx 1 310 838 7294 techsupport uninetimaging com www imaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 28 With the drum cover spring as shown on the end cap install the end cap Lift up the tail of the spring to fit onto the hopper 29 Lift up the drum cover sprint tail t
6. ng does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 1 With the handle facing you Remove the Right side screw and end cap from the cartridge Be careful of the drum cover spring Remove it with the end cap 2 With the pair of needle nose pliers release both the hopper tension springs A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 3 Slide the waste drum section over to the left side Separate the two halves 4 On the waste drum section lift the drum up from the gear 5 Remove the PCR and clean with your standard PCR cleaner side Twist and remove from the hopper A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING I
7. o fit as shown on the drum cover Install the screw into the cover SUMM TECHNOLOGIES 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www imaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS NOTES 30 Replace the chip REPETITIVE DEFECT CHART OPC Drum 75mm Magnetic roller 31mm PCR 27mm RUNNING TEST PAGES Test pages must be run from the P1006 menu Access the Printer Preferences menu then Services and Information pages There are three test pages that can be selected The Demo Config and Supply Status Page RUNNING THE CLEANING PAGE The cleaning page for these machines can only be run from the Printer menu HP recommends that for best results a transparency be used If a transparency is not available user copier grade paper with a smooth surface To run this page Access the printer preferences Click on Device Settings Press Start The cleaning cycle takes up to 2 full minutes The page will start and stop Do not turn the printer off until the cleaning page has finished printing PRINTER TROUBLESHOOTING As with all low cost machines these days this series of these machines do not have a display panel
8. rtridges are physically the same so you can make a High Yield cartridge from the starter If you can call 1500 pages high yield So far there are four printers based on this engine The P1000 the P1006 the P1007 and the P1008 At the time of this writing only the P1006 has been released The other models are referred to in the service manual Cartridge troubleshooting as well as running test pages cleaning pages and some simple printer troubleshooting will be covered at the end of this article Uninet e www uninetimaging com HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS SUPPLIES REQUIRED 1 100g Preliminary weight HP P1006 toner Unique to this series 2 New Drum Unique to this series 3 Wiper Blade Unique to this series 4 Dr Blade Unique to this series 5 Magnetic roller Unique to this series 6 Sealing Strip Unique to this series Cotton Swabs 8 Isopropyl Alcohol 9 Drum Padding Powder 10 Conductive Grease TOOLS REQUIRED 1 Phillips head screw driver 2 Small Common screw driver 3 Needle nose pliers 4 Jewelers Screwdriver set A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imagi
9. s Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS 13 On the toner supply chamber right side Remove the two screws and end cap Note that these screws have lock washers 14 Remove the gears from the hopper as shown Leave the large auger gear in place su AAT TECHNOLOGIES 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 e Fx 1 310 838 7294 techsupport uninetimaging com www imaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006 CARTRIDGE REMANUFACTURING INSTRUCTIONS NOTES 15 Remove the single screw and end from the opposite side Eo he eee T a appo raran iat Cie ES a Se 16 Remove the magnetic roller assembly Be careful of the bushings They are very fragile A TTT Uninet 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 techsupport uninetimaging com www uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information HP P1006
10. wo halves of the car tridge together is completely new The good news here is that you don t have to cut holes in the car tridge to get access to the pins The toner inside is also new HP is stating that the toner now has spherically shaped particles We are currently investigating if this means the toner is chemical or conventional toner that has been thermally rounded My guess is that it is thermally rounded toner but until our investigations are fin ished we won t know for Sure SUMMIT CHNOLOGIES 11124 Washington Blvd Culver City California 90232 USA Ph 1 310 280 9620 Fx 1 310 838 7294 e techsupport uninetimaging com 2008 UniNet Imaging Inc All Trademark names are property of their respective owners Product brand names mentioned are intended to show compatibility only UniNet Imaging does not warrant downloaded information T Se a 3 ro In addition to the new toner the chips have also had intelligence added to help aid cartridge ordering when supplies are low Again we are investigating the chips for these cartridges as write this can say have run the same cartridge now 5 times and the chip has not shut the printer down Just the toner low features are not working The printer when new comes with a starter car tridge that is rated for 700 pages at 5 coverage so your customers will be coming to you fairly quickly The starter cartridges and replacement 35A 1500 page ca
Download Pdf Manuals
Related Search