Operator Manual (PDF 4145 KB)
Contents
1. Water Do not put hands in wash water which may be over 60 and contain hazardous caustic detergent Rinse water be over 90 C Door safety switches are designed for emergency use only Cleaning Do not hose down the machine or splash water over the exterior Watch for broken glass etc when cleaning the inside of the machine Service repair Under no circumstances the user should attempt to carry out repairs All service repair work must be carried out by qualified personnel only Power Cord Replacement If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard 3 XU Operator Manual 141124 Installation Checklist WARNING Installer must be suitably qualified and ensure compliance with all codes and standards including AS NZS3500 1 Unpack Unpack the machine check for damage and complete delivery Positioning Place machine on sound waterproof self draining floor and adjust feet to level Allow room for adjacent chemical containers Water Flush supply lines before connection Connect hose supplied to adjacent accessible isolator valve 20 mm 3 4 male Flow rate required 20 litres per minute Temperature 65 C Consumption per cycle 2 6 litres Pressure required 200 350 kPa fit limiter above this pressure Back Flow Dual Check Valve DCV supplied with the machine Potable water quality is required filter or soften if nec2. used Excessive Rinse Fluid Remedy Check Water supply valve Check Door is closed Check Drain upstand is fitted Check arms spinning freely amp water supply temperature Check door is closed Check water temperature Use quality low foam product Do not overload racks Use Fisher pre rinse Remove and clean arms check bushes Remove arms and Clean jets Pre rinse use Long Cycle E g baked on soiling requires pre soaking Remove arms and Clean jets Remove arms clean jets check bushes Do not overload racks Pre rinse change wash water regularly Refer above Check heating systems Use quality drying agent rinse fluid Adjust Rinse Fluid Injector 120117 26 03 131A 2L0V DBA 50HZ RED N se 3 3 ra EM POWER SWITCH Q O BLACK 2 5mm NEUTRAL 2571 DOOR SWITCH RED ORANG Q DOOR SWITCH RELAY POWER ON LIGHT WASH READY LIGHT RINSE ELEMENT 3KW PRESSURE SWITCH yo RED 1 5mm RED 1 5mm BLACK 1 5mm RED 25mm i N O N C T WASH ELEMENT 2 5KW AO GREY 1 5mm BROWN 1 5mm ME WTCO BLACK 1 5mm RINSE TEMP 5 O READY LIGHT D GREY N C O O R1 O O O 15 C 22222226 22 2522 22 HELD OPEN O TIMER MOTOR O N O START WHITE RED O CYCLE LIGHT E 0 WHITE RED C O R2 DRAIN RELAY O RAPID START O N C DRAIN R2 SWITCH RED BROWN N C Q C YELLOW BROWN i 9 N lt a 0 YELLOW BLUE 4 5 A
3. 15 BLACK RED 1 5 NMOS NMOYg MOTI3A MOTI3A o 5 lt 5 NMOYg 038 ELZOE 009 HILIMS Poe ee d lz L0 8 85 Wana Ove IHM 4 NMOUG 00706009 MOTI3A HlNV3 IVNOILAO jl SISVH ESE 5 pe 20109 009 Jng dwnd 137014 1 038 anng 80113 4 2 8 06 009 38155384 MOTI3A CX MOTI3A 038731IH 3N18 MOTIA 2 X MOTI3A JONVYO 034 3LIHM 3DNVYO X MOTI3A 1800 009 0800 009 JSV8 8AV 138 we AV Id dWNd 67206 009 St 134718 GREEN 15 St IN3AW313 RED 15 5 RED 15 8800 009 110102 0210 MOTI3A 18006 009 08006 009 35 8 13101A VIOLET GREY 1 5 GREY RED 1 5 0206 1W1SOWNY3HL 3SNIY ZILOE 009 2 BLACK 25 RED 2 5 29 06 009 1 AQV3H 3SNIH AQV3H HSVM 21 INBLAC
4. A WASH PUMP x T2 0 15 HP O D 6uf CAP gt ne WHITE A HOT SOLENOID N 0 O C WHITE n A ES esas RINSE PUMP A 10mf IF FITTED ul Lad pes CAP 9 lt a o HELD OPEN O DETERGENT O PUMP DEGREES 0 30 60 90 120 150 180 210 240 270 300 330 360 SEC TIMER T1 WASH T2 118 SEC HOT RINSE T3 DETERGENT PUMP 100 103 SECI SEC 115 CAM CLOSEST TO 180 SEC TIMER MOTOR 05 ADJUSTABLE ee SEES 32661 001 preset cam 0 20 40 60 80 100 120 TIME IN SECONDS 9 XU Operator Manual 141124 120217 21 07 14 1B Refers to XU 2 Schematic Diagram 120117 BROWN 1 5 09 06 009 J INIWI13 HSVM BLACK 1 1008 LVLSOWYSHL HSVM 15 988 HSVM 768 ANId IVA ANId 3LIHM 3LIHM L 306 E x Be 09 3 2 x oj o LL 6006 009 ii 3983130 5 1 AVUL BNISIM TANVd IOGLNO MOTI3A 71 034 3LIHM LOLOE 009 HILIMS 1 15 69 06 009 LHOM 312429 71 gt 318 16206 009 IVE ZX 3LIHM 0103105 5 0 3118 0113 ANId BLACK
5. K 2 5 BLACK 15 LU BLACK x2 9106 009 1HDI1 LLZZE 13079 TVNIN43L gt tt SZ 038 SZ VIE 2 X 03 ody SZ Mv18 11006 009 HILIMS H3MOd 10 XU Operator Manual 140611 Accessories Nag F l Code 600 70029 600 70028 C660503 Description Cuprack 500mm Dishrack 500mm G Cutlery Container 11 XU Operator Manual 140611 Information supplied in this manualis copyright No part of this work may be reproduced or copied any form or means electronic or echanical without the express permission of the author publ PI e NI I Il 1 I Wil I WI 1 M MN DULL DUE DEAL A RO
6. e timer refer service set to a low injection rate and wil operator can adjust this via the ad refer service manual DRYING Single tank commercial dishwashe However the machines do rinse a promotes fast drying particularly At the end of the cycle promptly r machine leave the rack on the emptying This time will be reduce agent rinse fluid which reduces water to drain quickly from wash and injectors refer to your chemic WASH cedures by Food Hygiene Regulations The varm water with a Fisher scraping or dunking in water arm water preferably containing r your chemical supplier ontainers minimise the overlap d handles down onsumption per cycle low so ng racks rgent is essential for good results gularly check containers Discuss y pre soak solution with your centration can be changed by nanual Rinse Fluid is factory take many cycles to prime The justing screw on the front cover ors do not have a drying cycle t high temperatures which when drying agents are used emowve the rack from the inch for 2 to minutes before 2d with correct use of drying vater surface tension and allows ware For advice on drying agents al supplier TECH WASHTECH Care DAILY CLEANING It is essential that the machine is drained and cleaned at the end of each day Drain the machine as per the shut down instructions Remove clean and replace filters Regularly check the wash and r
7. echanical without the express permission of the author publisher Service 1800 622 216 Parts 1800 337 963 MOFFAT Distributed in Australia by Moffat Pty Limited 740 Springvale Road Mulgrave Victoria Tel O9 9518 3888 Fax 03 9518 3818 2 XU Operator Manual 141124 Safety Instructions WARNING Equipment contains dangerous voltages and can be hazardous if installed or operated incorrectly Non compliance with warnings or failure to follow the instructions contained in this manual can result in loss of life severe personal injury or serious damage to property Installation Use qualified skilled personnel Follow installation instructions Connect to correct voltage and supply current Provide fully accessible electrical Isolation Switch amp water supply valves Training and Supervision Read and understand the Operating instructions and train all staff This appliance must not be operated by children or infirm persons Machine panels must only be removed by suitably qualified and trained personnel internal hazards include live electrics and very hot surfaces This appliance is not intended for use as a stepladder Hot Surfaces Some surfaces may be hot or very hot Chemicals Commercial dishwashing detergents are hazardous handle with care Read and follow the safety information found on the labels of detergent containers and Material Safety Data Sheets Use protective eyewear and clothing if decanting containers Hot
8. essary Power Machine shipped with cordset for 15 A 240V 50Hz via adjacent switched outlet Waste Connect drain pump hose supplied to vented upstand or sink waste connection Detergent Note that detergent is hazardous read instructions and handle with care Insert hose into container of commercial dishwasher low foam detergent Pump will prime as machine fills and then come up to strength with use Rinse Fluid Insert hose into adjacent container of commercial dishwasher rinse fluid Injector accessible via front panel increase consumption by winding adjuster screw out Every turn out of the adjusting screw will increase the dose by about 0 4ml Operation Run several cycles ensure that operator has read and understands instructions Troubleshooting Installation If machine doesn t fill after switching on power check amp ensure that hot water supply tap is open water supply pressure is not below specification and DCV is correctly installed as per arrow on DCV body 4 XU Operator Manual 141124 XU Installation Diagram XU INST 16 10 14 3C 1035 the 635 o ol ob clearance 840 25130 ensure dual check valve supplied is located at water supply entry point Detergent C0 J Rinse Fluid 5 XU Operator Manual 141124 Machine Operation Power On Light Wash Ready Light Rinse Ready Light Drain Switch Start Button Power Switch Wash Temp Rinse Temp Cycle Lig
9. ht Gauge Gauge START UP Fit scrap trays filter drain upstand and shut door Turn wall and machine power switches on Power light glows red and machine fills automatically Wash ready light glows amber when wash tank is ready Rinse ready light glows amber when machine is up to required tempearature OPERATION Load rack into machine and shut door Press start button Cycle light glows green while machine operates When Cycle light goes out cycle is complete Remove rack Close door SHUT DOWN EVERY NIGHT Open door and turn Drain switch on After drain starts remove drain upstand when the top of the upstand is above the surface of the water Allow to drain for approximately 1 minute Turn Drain and Power switches off Remove scrap trays filter and rinse clean Replace filter and drain upstand Service 1800 622 216 Parts 1800 337 963 Operating Pro PRE RINSING Pre scraping of dishes is required best method is to pre rinse with v Pre rinse Unit or alternatively by Cutlery should be pre soaked in cutlery pre soak compound RACKING PROCEDURES Do not overload racks or cutlery c of crockery Wash cutlery unsorte Cycle times are short and water c there is no advantage in overloadi CYCLE TIMES The XU has a 2 minute cycle CHEMICAL Correct type and quantity of dete Use good quality chemicals and re the use of drying agent and cutler chemical supplier Detergent conc adjusting th
10. inse jets and clean if necessary see below REGULAR CLEANING at least once a week Remove upstand 1 and filter 2 Remove scrap trays 3 amp 4 Remove wash and rinse arms 5 by undoing the central thumbscrews 6 Inspect all jets use toothpick or paperclip and remove jets if necessary to flush and clear Clean and then replace all iterns aC 5 MAINTENANCE Regular servicing of the dishwasher is essential for high performance efficient operation and Long machine life Contact us for information on maintenance contracts Distributed in Australia by Moffat Pty Limited 740 Springvale Road Mulgrave 3170 Victoria Tel O3 9518 3888 Fax 9518 3818 Web ww w moffat com au Troubleshooting Fault Filling Not filling Filling during wash cycle Heating Dishes not hot enough Cycle start Does not start Cycle Finish Wash too long Performance Poor wash result Poor rinse results Not drying Foaming Wash 8 XU Operator Manual 141124 Cause Water supply valve shut Door Switch not operating Upstand not fitted properly Rinsing but not hot Door switch Water supply cold Detergent not used Overloading racks Not pre rinsing Wash arms not rotating Wash jets blocked Excessive soiling Unrealistic expectation Rinse jets blocked Rinse arms not turning Poor racking procedures Excessive wash tank soil build up Poor wash rinse performance Low temperatures Drying agent not
11. onan 6 58 WASHTECH PROFESSIONAL WASH SYSTEMS WARNING Before installation and commisioning you must read the safety instructions and warnings carefully and all the warning labels attached to the equipment IMPORTANT Failure to comply even partially with the instructions given in this manual will invalidate the product warranty and relieves the manufacturer of any responsibility IMPORTANT The alteration of machine operation design or the replacement of parts not approved by the manufacturer may void warranties and approvals 5 cipum gimus M NOR TRI na Bak s 9 M RET Open Pro T m Nou ee FV Wh Did GU A N a e o Ba II 10 We have checked that the contents of this document correspond to the model described There may be discrepancies nevertheless and no guarantee can be given that they are completely identical The information contained in this document is reviewed regularly and any necessary changes will be included in the next edition We welcome suggestions for improvement Specifications and document subject to change without prior notice Information supplied in this manual is copyright No part of this work may be reproduced or copied in any form or by any means electronic or m
Download Pdf Manuals
Related Search