TMA-HG-Pro Installation and Service Manual
Contents
1. Tap Master Artesian Hydro Gardener Owners Manual 7 Tips for an Easy and Successful Installation 1 Keep it simple there are 3 connections to make and the tubing is color coded 2 Have plenty of time light space and towels before getting started If everything goes well you should be done in 45 minutes However it can take somewhat longer 3 NEVER use plumber s putty thread lock or anything else you wouldn t eat on any part of this system You may use as much white Teflon plumber s tape as you like If you use plumber s putty on your fittings you will have disgusting and potentially toxic water for the life of the system 4 Mount the Tap Master vertically so that the back cap is on top There is only one plack cap and it has one grey fitting at its top Mount the permeate pump pro model correctly or nothing will work There is a big arrow on the permeate pump make sure it points up 5 Mount the drain saddle on a vertical section of drain pipe IF you must mount the drain saddle on a horizontal section then drill the drain hole on the top side of the pipe or at least at an angle where the drain water from the Tap Master drops down into the drain pipe Think of a manhole passage into the sewer When making the connec tion from the system to the drain saddle wrap the tubing around the drain pipe a few times so that some loops of tubing are higher than the fitting Tap Ma2. fittings are dry Water should flow normally from your sink s cold and hot faucet Double check to make sure all valves are in the CLOSED position except for the main angle stop valves which should be OPEN SLOWLY open the inline ball valve at the EZ adapter You should hear water flowing through the system Check for leaks at all fittings Allow 5 15 minutes for system pressure to build A thin steady or pulsing in Pro model trickle of water should be present after 2 20 minutes from the BLUE 3 tubing or your point of use Some blackening of the water may present due to loose carbon being flushed out Allow 10 gallons of water to be produced to flush the system and make it ready for use Membrane contains a mild preservative System must be flushed prior to use Enjoy 5b GARDEN HOSE INSTALLATION Pressurize the Tap Master Artesian Hydro Gardener Reverse Osmosis System Make sure unit is dry SLOWLY open the garden hose water valve SLOWLY open the inline ball valve at the EZ adapter You should hear water flowing through the system Check for leaks at all fittings Allow 5 15 minutes for system pressure to build A thin steady or pulsing in Pro model trickle of water should be present after 2 20 minutes from the BLUE 3 tubing or your point of use Some blackening of the water may present due to loose carbon being flushed out Allow 10 gallons of water to be produced to flush the system and make it ready for use Membr
3. Insert one end of the tubing into the EZ adapter and the other end into the inline ball valve Have a bowl or cup nearby to catch water and position the bowl near the inline ball valve Turn ON water by rotating angle stop counter clockwise until water is seen then close the ball valve by turning the handle perpendicular to the ball valve body Dry all parts check for leaks and snugness FOR ADDITIONAL INFORMATION ON USING QUICK CONNECT FITTINGS SEE PAGE 7 1b GARDEN HOSE INSTALLATION Install garden hose adapter on garden hose Locate the brass garden hose adapter see Fig 3 in the parts bag Fit the garden hose adapter onto the garden hose Use Teflon tape on the garden hose threads if necessary to make a leak proof seal and make sure o ring is properly seated Fit the garden hose adapter to the garden hose threads and HAND tighten Locate inline ball valve see Fig 6 in parts bag and its accompanying length of tubing Insert one end of the tubing into the garden hose adapter and the other end into the inline ball valve Have a bowl or cup nearby to catch water and position the bowl near the inline ball valve Turn ON the Page 4 Customer Service Hotline 1 877 693 PURE Weak pressure at RO sink faucet amp storage tank filling slowly Tap Master Artesian Hydro Gardener Owners Manual NOTE Seasonal changes in temperature can cause pressure imbalances within the system resulting in slow water production Oftentimes the imbal
4. ance will correct itself on its own within a few days You may also restore the internal system pressure balance by draining the tank removing a tube to relieve system pressure then shut off the system overnight Turn it back on and allow the tank to refill then shut it off again when full for another night 1 2 3 Make sure the angle stop or garden hose valve is fully open Check all tubing for kinks or sharp bends this can impede the flow of water Check household water pressure System performance based upon 7Opsi and 77 F input max hardness 171mg L lt 0 3 mg L iron Check flow to the membrane housing Turn off the water at the EZ adapter and briefly turn on the RO faucet or user supplied point of use to relieve any system pressure Then pull the black tube out of the top of the black membrane housing at the quick connect fitting There is only one fitting on the top of the membrane housing the bottom has two one white one grey Point the tube you have just disconnected into a pitcher and open the feed adapter valve The water flow from the tube should be fairly strong about a gallon per minute If the flow to the membrane housing is weak then check the water flow at each point in the system backwards to the feed valve until the blockage is found If the flow to the membrane housing is strong 5 then check flow at the RED 4 drain tube ensuring that it is unobstructed The water flow from the 3 BLUE tu
5. ane contains a mild preservative System must be flushed prior to use Enjoy DAAOULAL Jq UPD 9qGN 201 uontsod ST UT ppy 19103 IP YAY Sumy Jo 3z Jsuese Ajosenbs J303 mt ysna aqn aAOWaJ pue jajjO9 Ul YSNd SONILLIA LOANNOO MOINO ONISN qM IY UMOWA IsOJIq Pazisnssosdap st W iss IY IIMSU JJJUUOVJSIP OJ Customer Service Hotline 1 877 693 PURE
6. be should be a thin steady or pulsing trickle Discoloration of water The first batch of water produced from your purification system may be discolored due to the presence of carbon from the carbon filters and a small amount of preservative This is normal DO NOT drink the first 10 gallons of water Drinking from un flushed system may cause gastrointestinal discomfort colic and or diarrhea Consult a physician if discomfort persists Running out 10 gallons of water will effectively flush out the system and make it ready for use Air Bubbles Tiny air bubbles may be present in product water for some time after installation and filter changes and will dissipate when left to stand for a few seconds The air bubbles are harmless oxygenation and should not be mistaken for sedimentation or a defect in filtration Tap Master Artesian Hydro Gardener Owners Manual Troubleshooting IMPORTANT NOTE Before performing service on the Tap Master RO at any time and for any reason first switch to the OFF position all under sink water valves except for the RO faucet or your user supplied point of use which you should switch OPEN to relieve system pressure and drain away excess water from the lines Push pull and quick connect fittings are nearly impossible to remove when under pressure Leaks from metal fittings Unscrew fittings and re tape male fitting Tape should be wound 5 7 times around male thread Tape should not cove
7. in saddle and drain tubing Have a bowl and towel at hand Hissing clicking or flowing sounds from Tap Master RO are normal during the water purification process Sounds may last for approximately 1 hour per gallon of water used Sounds should stop once the reserve tank is full Permeate pump equipped systems will click and whoosh Customer Service Hotline 1 877 693 PURE Tap Master Artesian Hydro Gardener Owners Manual water to the garden hose then close the ball valve by turning the handle perpendicular to the ball valve body after the air is purged and water flows Failure to purge the air can lead to system damage and or diminished performance and or air bubbles in the product water for months Dry all parts check for leaks and snugness 2 Mount the Tap Master Artesian Hydro Gardener Reverse Osmosis System Identify a location for installing the Tap Master RO unit mounting clips The location should allow enough room for the for connecting and disconnecting the unit and for performing general service on the unit see Fig 4 For undersink installation typical locations are on either right or left side near the back wall Use supplied mounting clips and mounting template located inside the back cover of this manual The Tap Master should be mounted vertically where the drain line out is on the bottom Insert ORANGE 1 4 tubing from the Tap Master into feed water adapter inline ball valve used
8. in step 1 2a Mounting Permeate Pump Pro model Mount the permeate pump on the right side of the tap master using supplied mounting clip and screws IMPORTANT permeate pump must be mounted with indicator arrow pointing up Indicator arrow is the large center arrow See page 10 for mounting orientation diagram 3a UNDERSINK INSTALLATION Install drain saddle clamp and drain line Identify a vertical section of drainpipe with enough space to mount the drain saddle clamp See Fig 5 A horizontal section of drain pipe may be use to locate the drain saddle but you must be sure to drill the drain hole downward into the pipe so that the waste water from the Tap Master drips down into the pipe Drainpipe material can be either metal or plastic Locate drain hole template gasket supplied with drain saddle clamp peel off its backing and discard the perforated center piece Affix the sticky side of the template gasket on the previously identified location of drainpipe Place Ya drill bit inside template hole and drill a hole into the drainpipe Drill through one side only DO NOT drill a hole clean through both sides of the drainpipe This will result in a leak and require replacement of that piece of drainpipe Mount the drain saddle clamp on top of the template with the holes aligned You may use a screwdriver to align the holes Fit drain saddle clamp back plate and screws Alternate tightening screws on each side of the drain saddle clamp t
9. n a basement If the Tap Master is exposed to freezing it will burst If the Tap Master is exposed to the elements it can lead to premature wear and or contamination For best results the Tap Master should be mounted vertically where the drain line out is found at the bottom of the system Tap Master Artesian Hydro Gardener Owners Manual TUBING COLOR CODING ORANGE FEED WATER IN BLUE PURIFIED WATER OUT RED WASTE WATER Tools Required Safety glasses Towels Phillips screwdriver Scissors Medium Crescent wrench Medium pliers Teflon tape READ ALL INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLATION Installing The Tap Master Artesian Hydro Gardener Reverse Osmosis System 1a UNDERSINK INSTALLATION Install feed water EZ adapter on COLD water line Always wear protective eyewear while under sink Locate the COLD angle stop the main water lines under the sink one hot water one cold water see Fig 1 and turn clock wise to shut off the water Locate 3 fitting typically found on the line out of the angle stop or where the existing line connects to the kitchen faucet Disconnect the fitting on either the angle stop or the kitchen faucet Use Teflon tape on the EZ adapter see Fig 2 and the angle stop male threads and make sure o rings are properly seated Fit the EZ adapter to the threads and HAND tighten Locate inline ball valve see Fig 6 in parts bag and its accompanying length of tubing
10. o ensure an even snug fit See Fig 5 Locate RED drain tubing and push on black plastic nut found in drain saddle bag onto the tubing then wrap excess tubing around the drainpipe before hand tightening black plastic nut onto the drain saddle male fitting until it is snug Tap Master Artesian Hydro Gardener Owners Manual Tap Master Artesian Hydro Gardener Owners Manual 3b Floor drain installation Affix the RED drain tubing above the floor drain such that the drain tubing is at least 3 above the high point of any standing water Do not allow the opening of the RED 4 drain tubing to come in contact with the ground or any standing water 1NDBS MO 0 UD 4 Water line out to point of use Locate BLUE 3 tubing and connect to the user supplied point of use using a user supplied fitting Do not allow the opening of the BLUE 3 tubing to come in contact with the ground or any standing water vas joosd yea JuaueUJad e s pmosd Sun 0 IP apy VONTsod ut AU aqny ay DIOU YYA YIII IIS ssayuTEys sey saddis3 309 ayy dote aqny ay 0 Sumy 20 OUT 2001 ay ysna dojs aqn 0 dn ysng eqn Wesu ISN JJOJIq JO PUL IIS BUVI 0 JOLId WaysAs IY 189 0 JdNIvId POO L et I 9INDIS SI IF TE YOIYD 0 2001 ay UO Jnd 5a UNDERSINK INSTALLATION Pressurize the Tap Master Artesian Hydro Gardener Reverse Osmosis System Make sure unit exterior and
11. p Master Artesian Hydro Gardener Contents 1 Instruction book detailed descriptions photos and troubleshooting guide 1 10 Sediment pre filter 5 micron bonded spun poly depth 1 10 Carbon pre filter 5 micron granular activated coconut shell carbon 1 10 Artesian post filter 5 micron granular activated coconut shell carbon with advanced remineralization media 1 Thin Film Composite membrane 0 001 micron ultra fine pore 150 gallon per day 10 000 gallon service life GPD performance based upon 7Opsi and 77 F input 1 Flow restriction architecture integrated flow restrictor and water check valve and central auto shut off valve or permeate pump pro model 1 Drain saddle all fittings and connecting hardware 1 EZ adapter feed water adapter 3 mc x 3s fc x 4 tube 1 Garden Hose Adapter feed water adapter 34 x 14 tube 1 Inline Ball valve tube x tube Maintenance Schedule Sediment filter 3 900 gallons or as needed Carbon filter 3 900 gallons or annual replacement Membrane 150 gpd TFC 10 000 gallons or as needed Artesian filter 2 500 gallons or annual replacement General System Specifications e Feed water PSI 40 100 PSI e Feed water Temperature 40 100 F e Max Total Dissolved Solids TDS 2000 ppm e Max Hardness 10 gpg e pH limits 4 10 System Location The Tap Master should be installed indoors or protected from the elements such as under a sink or i
12. r opening Use only Teflon tape Re tighten fitting securely Over tightening can crush the tubing insert and cause a water blockage Leaks from plastic fittings Plastic fittings should be firmly finger tightened Under tightening can result in leaks over tightening can crush the tubing and result in a water blockage For plastic fittings only make sure the plastic tubing has an insert in the tube end and a feral o ring which compresses the tubing around the insert in the plastic female fitting Drain tubing does not need an insert Leaks from quick connect push pull or Speedfit fittings Disconnect fitting by pushing in the tubing with one hand and depressing the ring on the fitting with the other hand Then pull out tubing while the ring is still depressed Tubing cannot be pulled out without depressing the fitting ring and relieving system pressure Make sure the tubing is cut is straight the edge is completely smooth and the tube is rounded Scratched gouged damaged or oblong tubing end will leak Re insert the tubing into the push pull fitting Push tubing all the way in then pull back gently to check fit Most push pull fittings take about a 1 3 of tubing inserted into them No water from Tap Master RO System Make sure all valves are on the ON position Check for over tightening of fittings Eliminate possible blockage points by disconnecting each system component and checking for pressure Check for blockage in dra
13. ster Artesian Hydro Gardener Tap Master Artesian Hydro Gardener Pro 6 Read the instructions thoroughly before beginning There is a lot of information here some of which you may not need for your application If you have questions call or email Email will usually be answered within hours even at night 7 Have patience Your new Tap Master may take some time to break in and start flowing Make sure you produce and flush out 10 gallons of water before use TUBING COLOR CODING ORANGE FEED WATER IN BLUE PURIFIED WATER OUT RED TO DRAIN THE PERFECT WATER Perfect Water Technologies Inc Copyright 2010 Customer Service Hotline 1 877 693 PURE Tap Master Artesian Hydro Gardener Owners Manual Fig 1 Angle stop Fig 4 Mounting clips for Tap Master amp permeate pump ES Fig 2 EZ adapter Fig 5 Drain saddle Fig 3 Garden hose Fig 6 Inline ball valve adapter Customer Service Hotline 1 877 693 PURE mab me O2Z2 AaZcos aman b vp ALLOW 6 CLEARANCE FROM TOP ALLOW 6 CLEARANCE FROM BOTTOM Tap Master Artesian Hydro Gardener Owners Manual MOUNTING ORIENTATION CORRECT INCORRECT PERMEATE PUMP MOUNTING Permeate pump should be mounted with inlet and outlet ports to the sides and the center indicating arrow pointing up Also see Fig 4 Customer Service Hotline 1 877 693 PURE Tap Master Artesian Hydro Gardener Owners Manual Ta
Download Pdf Manuals
Related Search