JCM® VEGA™ Quick Reference Guide Rev. 2
Contents
1. No Paper Transmissive Validation Sensor With Paper Light Interception Side Sensor With Paper Light Interception No Paper Transmissive Escrow Sensor With Paper Light Interception No Paper Transmissive No Paper Transmissive RC Flap Sensor With Paper Transmissive No Paper Light Interception Stacker Flap Sensor With Paper Transmissive No Paper Light Interception Stack In Sensor With Paper Light Interception No Paper Transmissive Box Sensor With Paper Light Interception No Paper Transmissive When the selected Sensor detects an object such as a Banknote or a Test Paper the Front Panel LED Display will blink at a Yellow Color Rate When there is no object detected the Front Panel LED Display will be extinguished out NON PC CALIBRATION PROCEDURE NOTE Calibration using a PC exists and is found in Section 6 Ee pg 6 6 of the VEGA Operations and Maintenance Manual Begin the Non PC No Serial No Written Calibration Procedure as Follows 1 Turn the Vega Unit s Power OFF 2 Set DIP Switch Block No 1 Switches 1 2 amp 8 ON and set DIP Switch Block No 2 Switches ALL OFF C NOTE DIP Switch Block No 3 settings are not required to perform this Calibration Procedure 3 Turn the VEGA Unit s Power ON The Front Panel LED will slowly blink at a Green Color Rate 4 Set DIP Switch Block No 1 Switch 1 to OFF 5 When mo2. 12 Set DIP Switch Block No 2 switch 3 to ON This action performs the Validation Sensor s Adjustments using the Black Reference Paper Ee NOTE Keep DIP Switch Block No 2 Switch 1 2 amp 3 ON until prompted to turn them OFF C NOTE While the adjustment process is active the Blue LED will momentarily flash at a high rate of speed 2013 JCM Global Corporation 14 Part No 960 000163R_Rev 2 13 14 15 16 17 18 VEGA Units Once the Black Reference Paper Validation Sensor s Adjust ments are complete the Front Panel LED will slowly blink at a Purple Color Rate Remove the Black Reference Paper from the Transport Section Set DIP Switch Block No 2 Switch 4 to ON This action re performs the Validation Sensor s non paper adjustment pro cedure ee NOTE Keep DIP Switch Block No 2 Switches 1 2 3 amp 4 ON until prompted to turn them OFF gt NOTE While the adjustment process is active the t a Front Panel LED will flash a Purple Color at a high rate of speed Once the Validation Sensor s Non paper Adjustment Proce dure is complete the Front Panel LED will slowly blink at a Green Color Rate Set DIP Switch Block No 2 Switch 5 to ON This action performs the Edge Sensor s Non paper Adjustment Proce dure FF NOTE Keep DIP Switch Block No 2 Switches 1 2 3 4 amp 5 ON until prompted to turn them OFF FF NOTE During the adjustment process the Front
3. JCM Products Quick Reference Guide VEGA Units NOTE Due to advancements in related industry technologies and future product development the information in this guide is subject to change without notice For more information about product set up use testing procedures and troubleshooting methods please contact the Technical Support Division of Customer Service via the email addresses listed below Americas support jcmglobal com Europe UK Africa Russia amp Middle East support jcmglobal eu Asia amp Oceania asiapactechsupport jcmglobal com 2013 JCM Global Corporation Part No 960 000163R_Rev 2 VEGA Units QUICK REFERENCE TROUBLESHOOTING GUIDE Cleaning Procedure To clean the VEGA Unit Lenses use a lint free Microfiber Cloth and a mild non abrasive detergent such as liquid dish soap mixed with water It is important to keep the Banknote path Rollers and Belts clean Use the lint free cloth or a Cotton Swab to wipe dirt and stains from the surfaces of the Magnetic and Optical Sensors Rollers and Belts The Sensor Lenses are transparent and made of a Polymer material handle them with care Repeat the cleaning process as needed until the Transport path is free of contaminants SENSOR CLEANING PROCEDURE To properly clean the VEGA Unit s Sensors proceed as follows 1 Turn the VEGA Unit s Power OFF 2 Open the Upper Validation Section 3 Clean the appropriate path in the location of eac
4. Units SENSOR TEST Perform the following steps to verify if the eight 8 Sensors within the VEGA Unit are functional i e the Entrance Validation Side Escrow RC Flap Stacker and Box Sensors when using the Paper and Non paper Calibration Procedures 1 2 3 4 Ensure the VEGA Unit s Power is OFF Set DIP Switch Block DS1 Switch 1 2 3 4 amp 5 to ON Turn the VEGA Unit s Power ON Set DIP Switch Block DS1 Switch 1 to OFF The Front Panel LED will extinguish go out Sensor Confirmation will be Stand by Mode active Table 6 and Table 7 list the DIP Switch Block DS2 settings for the Sensor Test Configurations Select the desired Sensor from the Tables and set DIP Switch Block DS2 Switches according to the Sensor Configuration Table settings set in Table 6 Table 6 DIP Switch Block DS2 Sensor Configuration Switch Settings DIP Switch Block DS2 Sensor Entrance Sensor Validation Sensor Side Sensor Escrow Sensor RC Flap Sensor Stacker Flap Sensor Stack In Sensor Box Sensor Table 7 on page 13 lists the Yellow LED States related to the DIP Switch Block DS2 setting chosen in Table 6 2013 JCM Global Corporation 12 Part No 960 000163R_Rev 2 VEGA Units Table 7 DIP Switch Block DS2 Sensor LED State Conditions Yellow LED State Sensor Lit Extinguished Entrance Sensor With Paper Light Interception
5. ticular Test selected F amp F NOTE Reset DIP Switch DS1 Switch 1 to ON again to STOP the current Test and return to the Stand by Mode After performing an Off line Banknote Acceptance Test cycle the VEGA Unit s Power OFF amp ON to return to the Stand by Mode Unless the power is turned OFF amp ON the next Test WILL NOT run DIP SWITCH TEST Perform the following steps to test the functionality of each DIP Switch Block 1 Ensure that the VEGA Unit s Power is OFF 2 Set all Switches on DIP Switch Blocks DS1 and DS2 to ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 to OFF When the DIP Switch Test begins the Front LED will extinguish go out 5 Set the ODD numbered DIP Switches on Switch Blocks DS1 and DS2 to OFF The Front Panel LED display will blink at a Yellow Color Rate 6 Set the EVEN numbered DIP Switches on Switch Blocks DS1 and DS2 to OFF The Front Panel LED Display will blink at a Blue Color Rate if all the DIP Switches functioned correctly FF NOTE If the DIP Switches were set incorrectly during the Test the Front Panel LED Display will flash Red indicating a test failure However if the DIP Switches were set correctly and the LED still flashes Red then a DIP Switch failure is indicated 2013 JCM Global Corporation 7 Part No 960 000163R_Rev 2 VEGA Units FEED MOTOR FORWARD ROTATION TEST Perform the following steps to test the normal forward rotati
6. DS 1 Switch 1 to ON 2 Turn the VEGA Unit s Power ON and the performance Test Mode will activate F amp F NOTE When the VEGA Performance Test Mode begins the Front Panel LED will slowly blink at a Green Color Rate Table 1 and Table 2 lists the various Performance Test DIP Switch Settings for each Type of Test Table 1 Performance Test DIP Switch Block 1 Configuration Settings DIP Switch Block 1 Switch Number Test Type 213141516 71 8 DIP Switch Test ON ON ON ON ON ON ON Feed Motor Normal Rotation Test Feed Motor Reverse Rotation Test Stacker Motor Test Aging Test Off line Banknote Acceptance Test Sensor Test Stand by Color Indication Cycling Rainbow Gradation Stand by Color Indication Green t Stand by Color Indication Blue ccTalk Encryption Code Initialization See Stand by Mode LED Assignment Indication on page 2 3 of the Vega Service Manual for making a Rainbow Gradation setting See Stand by Mode LED Assignment Indication on page 2 3 of the Vega Service Manual for making the GREEN Color setting See Stand by Mode LED Assignment Indication on page2 3 of the Vega Service Manual for making the BLUE Color setting See Rewriting ccTalk Encryption Code Initialize on page 2 3 of the Vega Service Manual for making the communications Protocol setting 2013 JCM Global Corporation 5 Part
7. Panel LED will flash a Green Color at a high rate of speed Once the Edge Sensor s Non paper Adjustment Procedure is complete the Front Panel LED will slowly blink at a Yellow Color Rate Set DIP Switch Block No 2 Switches 1 2 3 4 amp 5 OFF in order to write these adjustment results into the VEGA Unit s EEPROM Memory F amp F NOTE While writing the data into the EEPROM the Front Panel LED will flash a Yellow Color at a high rate of speed EF NOTE If EEPROM data writing fails all previous adjustment s data will be lost which may disable the VEGA Unit 2013 JCM Global Corporation 15 Part No 960 000163R_Rev 2 VEGA Units 19 Once the data writing procedure is complete the Front Panel LED will blink at a Green Color Rate 20 Turn the VEGA Unit s Power OFF NOTE If the adjustment of ANY Sensor fails the Front Panel LED will blink Red If this error condition occurs ensure that the procedures were correctly performed and then re perform them Refer to Table 8 for a detailed explanation of each Red Color blink sequence indication Table 8 Red LED Blink Rate Errors Blink LED Colors Sequence Error Indication 1 Blink The Entrance Sensor adjustment has failed 2 Blinks The Entrance Sensor adjustment using White Reference Paper has failed 3 Blinks The Validation Sensor adjustment using Black Reference Paper has failed 4 Blinks ane yausation Sensor s Non Pa
8. following steps to perform the VEGA Unit s Off line Banknote Acceptance Test 1 Ensure that the VEGA Unit s Power is OFF 2 Set DIP Switch Block DS1 Switch 1 3 amp 5 to ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 to OFF When the off line Banknote Acceptance Test begins the Front Panel LED will extinguish goes out Wait for the Front Panel LED Display to indicate a Stand by Mode initialization blinking sequence then insert Banknotes When the VEGA receives the Banknotes the Front Panel LED will blink an Emerald Green Color The acceptable denominations are identified by the following Front Panel LED blink sequences p gt NOTE Euros are shown as an example 5 Denomination Values 1 Blink e 10 Denomination Values 2 Blinks 20 Denomination Values 3 Blinks 50 Denomination Values 4 Blinks e 100 Denomination Values 5 Blinks The Denomination Value represents the specific Country s Currency Type Check the related Country s Software Information Sheet for specific denominations NOTE Between sequential Banknote insertions the Color of LE the Front Panel LED Display will be determined by the Stand by Mode selections set by the User F NOTE If an error or a reject occurs refer to the Error and Reject Codes listed in Table 10 or Table 11 to identify the cause of the malfunction 2013 JCM Global Corporation 11 Part No 960 000163R_Rev 2 VEGA
9. 0 in this Guide for Error Codes and Bezel LED foreign object in path Perform the necessary action flashes Red gn ob pai Software not designed Check related Country s Software Information to accept current Sheet for correct denominations Country s Banknotes Download the correct Software Most Banknotes DIF wach satinga are Insure DIP Switch settings are properly set tbe rejected i Bezel LED Host Machine Banknote flashes Yellow accept inhibit settings Check Host Machine command is correct may exist Dirt or foreign objects on Sensors Clean the Sensors 2013 JCM Global Corporation 17 Part No 960 000163R_Rev 2 LED Symptoms VEGA Units Table 9 LED Diagnostics Continued Causes Solutions Most Banknotes are rejected Bezel LED flashes Yellow Improper Harness connection malfunctioning Circuit Board Check all Cable Connections See Table 11 in this Guide for error codes and perform the necessary action required Old Software version Banknote not supported by Country s Software Confirm required denomination and or desired Country s issued year is correct on Software Information Sheet Dirt or foreign objects on Sensors Clean the Sensors Sensor Calibration need to be performed 2013 JCM Global Corporation See Table 10 for Error Codes and perform necessary action required Perform Calibration Tests as necessary
10. 18 Part No 960 000163R_Rev 2 VEGA Units Table 10 Error Codes on line off line Color Color Error Causes and Solutions Flashes Flashes msec msec Yellow ROM Error ROM malfunction Re download the current 1 300 Software Change CPU Circuit Board Yellow 14300 Yellow 2 300 RAM Error RAM malfunction Change CPU Circuit Board White Feed Motor During Feed Motor operation no pulse inputs exist 3 300 Low Speed greater than rated value White Feed Motor During Feed Motor operation no pulse inputs exist 5 300 High Speed greater than rated value During Feed Motor operation no pulse inputs exist White Feed Motor greater than rated value Error occurs during 7 300 Lock up initialization or when a Banknote is at a transport position where it can not be returned Purple Stacker During Stack Motor operation no pulse inputs exist 5 300 Motor reater than the rated value Lock up g Purple Vue The Pusher Mechanism stays in its Home Position 7 300 Problem while the Stacker Motor is operating Red 3 300 An abnormal Banknote transportation error occurs Banknote when transporting or rejecting Banknotes The Blue Transport Transportation Slip Sensors do not detect 2 300 Sli continuous Banknotes being transported according P to the rated value An abnormal Banknote transport error occurs when transporting or rejecting Banknotes The 3 800 T
11. No 960 000163R_Rev 2 VEGA Units Table 2 Performance Test DIP Switch Block 2 Configuration Settings DIP Switch Block 2 Switch Number Test Type DIP Switch Test Feed Motor Normal Rotation Test Feed Motor Reverse Rotation Test Stacker Motor Test Aging Test Off line Banknote Acceptance Test Sensor Test Stand by Color Indication Cycling Rainbow Gradation Stand by Color Indication Green t Stand by Color Indication Blue ccTalk Encryption Code Initialization See Stand by Mode LED Assignment Indication on page 2 3 of the Vega Service Manual for making a Rainbow Gradation setting t See Stand by Mode LED Assignment Indication on page 2 3 of the Vega Service Manual for making the GREEN Color setting See Stand by Mode LED Assignment Indication on page2 3 of the Vega Service Manual for making the BLUE Color setting See Rewriting ccTalk Encryption Code Initialize on page 2 3 of the Vega Service Manual for making the communications Protocol setting 2013 JCM Global Corporation 6 Part No 960 000163R_Rev 2 VEGA Units Performance Test Initiation Set the various DIP Switches listed in Tables 1 amp 2 for each Test desired AFTER the Performance Test Mode has been activated Once the DIP Switches on both Block 1 and Block 2 have been set for the desired Test set DIP Switch DS1 Switch 1 to OFF to begin the par
12. Rev 2 VEGA Units AGING TEST The Aging Test repeatedly performs basic Validator functions such as feeding transporting and stacking operations Perform the following steps to repeatedly Test the VEGA Unit s basic functional performance 1 Ensure that the VEGA Unit s Power is OFF 2 Set DIP Switch Block DS1 Switches 1 2 and 4 ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 OFF When the Aging Test begins the Front Panel LED will extinguish go out 5 If operation is normal the Unit will perform the following five functions repetitively until the Test is stopped Feed Motor Reverse Rotation Test Interval Test 20 sec LED lights White Feed Motor Forward Rotation Stacking Test Interval Test 20 sec LED lights White To end the Aging Test turn the VEGA Unit s Power OFF or set DIP Switch Block DS1 Switch 1 to ON NOTE If the Front Panel LED blinks ANY Error sequence indicated in Table 5 the Feeding and or Stacking function is abnormal Table 5 Feeding Stacking Abnormal Error Codes monoge Blink Sequence Error Indication Feed Motor Low Speed Problem Feed Motor High Speed Problem Feed Motor Lock up Red Cash Box Seating Problem Stacker Motor Lock up Purple Stacker Motor Gear Problem Orange Stacker Full 2013 JCM Global Corporation 10 Part No 960 000163R_Rev 2 VEGA Units OFF LINE BANKNOTE ACCEPTANCE TEST Perform the
13. Yellow during a download Once the download is complete the Front Panel LED Dis play will turn a steady Blue Color and then the VEGA will return to a Start up Process condition e g the Front Panel LED Display blinks at a Green Color Rate When downloading is complete confirm that the Host s Checksum and the devices Checksum match each other e g CRC XXXX CRC XXXX 2013 JCM Global Corporation 3 Part No 960 000163R_Rev 2 VEGA Units Ee NOTE If the Host and the Device CRC Checksums DO NOT match the download did not end correctly Confirm the download procedure is correct and re perform the download Procedure again 10 After verifying that a CRC match between both Checksums exists Mouse click on the OK Dialog Screen Button to close the UBA Downloader Program Screen NOTE If the word Manual appears in the Reset Pull down Menu the Front Panel LED will sustain a steady Blue color In this case return to the Start up condition by pressing the adjacent Manual Reset Screen Button located to the right of the Pull down Menu The Front Panel LED will then blink at a Green Color Rate Ee NOTE If a download error occurs the Front Panel LED will light a steady Red Color 2013 JCM Global Corporation 4 Part No 960 000163R_Rev 2 VEGA Units Performance Test Mode Activation Perform the following steps to activate the VEGA Unit s self con tained Performance Tests 1 Set DIP Switch Block
14. e direction the Front Panel LED Display will be extinguished dark and reverse rotation will continue To end the Reverse Feed Motor Test turn the VEGA Unit s Power OFF or set DIP Switch Block DS1 Switch 1 to ON F amp F NOTE If the Front Panel LED Display blinks ANY White Error sequence listed in Table 3 on page 8 the Feed Motor s reverse rotation is abnormal STACKER MOTOR TEST Perform the following steps to test the Stacker Motor s rotational functionality 1 Ensure that the VEGA Unit s Power is OFF 2 Set DIP Switch Block DS1 Switches 1 and 3 ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 OFF When the Stacker Motor Test begins the Front Panel LED will extin guish go out 5 Ifthe Stacker Motor rotates forward and reverse correctly the Front Panel LED Display will be extinguished dark and the Motor will continue operating in a forward reverse direction 6 To finish the Stacker Motor Test turn the VEGA Unit s power OFF or set DIP Switch Block DS1 Switch 1 ON NOTE If the Front Panel LED blinks ANY Error sequence indicated in Table 4 the Stacker Motor s rotation is abnormal Table 4 Stacker Motor Abnormal Error Codes LED Blink Color Sequence Error Indication Red 5 Cash Box Seating Problem Purple 5 Stacker Motor Lock up Purple 7 Stacker Motor Gear Problem Orange 3 Stacker Full 2013 JCM Global Corporation 9 Part No 960 000163R_
15. h 3 120 Transport the number of Banknotes transported is more P than the accepted value Red Sensors do not detect movement even though Yellow Transport Banknote transportation time is longer than Red Time out acceptable 3 120 Blue Yellow Transport While Feed Motor is operating no pulse inputs Lock U exist greater than the rated value Blue p 3 120 Green Purple Transport While performing a transportation process pulse Speed High interaction was shorter than the accepted value Yellow econ 3 120 3 120 Red Abnormal Sensor detected a Banknote remaining in path 3 120 Timing or none present during an abnormal timing Response interval Yellow R s The Side Sensor detected a Banknote before it White Sige Sensor passed through the Guide Sensor and after it passed the Banknote through the Side Sensor Yellow 3 120 Validation Software does not match the required Country s Problem specification Validation Wrong DIP Switches settings 31120 Problem Most Inhibited validation due to conflicting Host Banknotes Command settings are rejected Adhering foreign objects or dirt on the Sensors 2013 JCM Global Corporation 21 Part No 960 000163R_Rev 2 VEGA Units Table 11 Reject Codes Continued on line off line Color Color Causes and Solutions Flashes Flashes msec msec Validation Software version old or a disabled Problem denomination Banknote was i
16. h Sensor as well as the Sensor itself WARNING Do not use Alcohol paint thinner At amp solvents or citrus based solutions for cleaning any surfaces 2013 JCM Global Corporation 2 Part No 960 000163R_Rev 2 VEGA Units OPERATIONAL MODE FUNCTIONS Software Download Procedures Perform the following steps to download the VEGA Operating Soft ware Application Before downloading the Software copy the Down loader Application UBA Downloader Version 2 10 specified and the VEGA Operating Software Application into a new Folder named VEGA created on the PC e g C WEGA 1 PA 3 4 Turn the VEGA Unit s Power OFF Set DIP Switch Block No 1 Switches 1 7 amp 8 to ON Turn VEGA Unit s Power ON Confirm that the Front Panel LED blinks at a Green Color Rate Launch the copied Downloader Application UBA Down loader Version 2 10 from the recently created PC VEGA Folder C VEGA When Program Installation Screen appears Mouse click on the Browse Screen Button and select the desired VEGA Software 1 e VEGA_ EUR for download into VEGA Flash Memory then Mouse click on the Open Screen Button to launch the selected File When the UBA Downloader Screen reappears Mouse click on the center Download Screen Button to begin download ing the Software into VEGA Flash Memory The download ing Screen will display a Progress Barograph during the download operation NOTE The Front Panel LED lights
17. ilton Keynes Buckinghamshire MK1 1EJ Phone 44 0 1908 377 331 Fax 44 0 190 837 7834 E mail info jcmglobal eu JCM Gold HK Ltd Unit 1 7 3 F Favor Industrial Centre 2 6 Kin Hong Street Kwai Chung N T Hong Kong Phone 852 2429 7187 Fax 852 2929 7003 E mail asiapactechsupport jcmglobal com VEGA Units Quick Reference Guide Part No 960 000163R_Rev 2 2013 JCM Global Corporation VEGA Units JCM International Offices JCM American 925 Pilot Road Las Vegas NV 89119 Phone 1 702 651 0000 Fax 1 702 644 5512 E mail support jcmglobal com USA Regional Offices Illinois Office 3000 Dundee Road Ste 402 Northbrook IL 60062 Office 847 418 3354 Fax 847 418 3357 Mississippi Office 4063 Ginger Drive Ste B D Iberville MS 39540 Office 228 344 8601 Fax 228 354 8608 VEGA Units Quick Reference Guide ELEC es 2013 JCM Global Corporation Part No 960 000163R_Rev 2
18. nserted Only specific Adhering foreign object or dirt on the Sensors Banknotes are rejected or the validation Cal rate is degraded ibrate Sensors After a disassembly reassembly or parts repair replacement Short Banknote length exists While waiting for Validation Sensor detection the Intake Sensor detected no bill present Or while transporting Banknotes the Escrow Sensor waited for Banknote insertion detection and the Intake Sensor detected a no bill present condition Long Banknote Length exists a Banknote was inserted having a length greater than 165mm Blue Double The Validation Sensor s transitional level is less 3 120 Banknotes than the accepted value Dirt stickers or foreign objects may be on the Banknote Red Cash Box Seating Red Problem 3 120 Blue Cash Box Sensors detect a Banknote remaining in path White Purple Pusher Pusher Mechanism Home Sensor detects that Mechanism the Pusher Mechanism is not presently at its White Problem Home end position 3 120 2013 JCM Global Corporation 22 Part No 960 000163R_Rev 2 VEGA Units JCM International Offices Japan Cash Machine Germany GmbH Muendelheimer Weg 60 D 40472 Duesseldorf Germany Phone 49 211 530 645 60 Fax 49 211 530 645 85 E mail support jcmglobal eu JCM United Kingdom Ltd Unit B Third Avenue Denbigh West Business Park Bletchley M
19. onal functionality of the Feed Motor 1 Ensure the Vega Unit s Power is OFF 2 Set DIP Switch Block DS1 Switch 1 to ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 to OFF When the Feed Motor Forward Rotational Test begins the Front Panel LED will extinguish go out 5 Ifthe Feed Motor correctly rotates in a forward direction the Front Panel LED Display will be extinguished dark and for ward rotation will continue 6 To end the Forward Feed Motor Test turn the VEGA Unit s Power OFF or set DIP Switch Block DS1 Switch 1 to ON EP NOTE If the Front Panel LED Display blinks ANY White Error sequence listed in the Table 3 Chart the Feed Motor s forward rotation is abnormal Table 3 Transport Motor Abnormal Error Codes Blink Sequence Error Indication Feed Motor Low Speed Problem Feed Motor High Speed Problem Feed Motor Lock up Problem FEED MOTOR REVERSE ROTATION TEST Perform the following steps to test the normal reverse rotational functionality of the Feed Motor 1 Ensure the Vega Unit s Power is OFF 2 Set DIP Switch Block DS1 Switches 1 and 2 ON 3 Turn the VEGA Unit s Power ON 4 Set DIP Switch Block DS1 Switch 1 to OFF When the Feed Motor Reverse Rotational Test begins the Front Panel LED will extinguish go out 2013 JCM Global Corporation 8 Part No 960 000163R_Rev 2 VEGA Units 5 Ifthe Feed Motor correctly rotates in a revers
20. per adjustment has 5 Blinks The Edge Sensor adjustment has failed 6 Blinks The EEPROM data writing process has failed 2013 JCM Global Corporation 16 Part No 960 000163R_Rev 2 VEGA Units Table 9 Table 10 and Table 11 on the following pages of this Quick Reference Guide list the possible Malfunction LED Error Codes are identified by various LED flash counts and Colors When Error Codes and Reject Codes are not indicated e g the VEGA s Bezel LEDs are not lit or not identified in detail find the probable cause in these Tables and take the appropriate action Table 9 LED Diagnostics LED a Symptoms Causes Solutions i Check Cable Connections and verify that Power is not supplied appropriate Power is supplied Program not activated VEGA is not Software download Re download the correct Software working incomplete Bezel LED is a TAE not lighting Melrunctoning Circuit Insure that internal Harnesses are connected Interface DIP Switches Check that the Interface and the DIP Switch settings are not correct settings are correct VEGA is not working ROM or RAM See Table 10 in this Guide and perform the Bezel LED Malfunctioning necessary action required Flashes Yellow VEGA is not ee working Hnit setting is Insure connections are properly seated Banknote Jam Improper connection Clear Banknote Jam or foreign object from path occurs Hiatal Jamora See Table 1
21. ransport transportation Locks up or runs too slow Sensors detect continuous Banknotes being transported according to the rated value Red dus Sensors detect Banknotes remain in path or none 3 300 Response exist during abnormal timing Red Cash Box Cash Box Sensors detect a Banknote remains in 5 300 Seating path or a Cash Box not properly seated 2013 JCM Global Corporation 19 Part No 960 000163R_Rev 2 VEGA Units Table 10 Error Codes Continued off line Color Color Causes and Solutions Flashes Flashes msec msec Purple Pusher Pusher Mechanism Home Sensor detects that the 3 300 Mechanism Pusher Mechanism is not presently seated at the Position Home end position When the Pusher Mechanism moves toward stacking the Stacker full Sensor determined that the time taken is longer than specified value for the function Orange 3 300 Stacker Full Intake Sensor detects Banknote at a position where it can not be returned while in the transport process Cyan Operational 3 100 Pause The Flash error pause time between blinks is a 100msec duration 2013 JCM Global Corporation 20 Part No 960 000163R_Rev 2 VEGA Units Table 11 Reject Codes on line off line Color Color Error Causes and Solutions Flashes Flashes msec msec A Sensor does not detect a Banknote even thoug
22. ving into the Adjustment Mode the Front Panel LED will slowly blink at a Cyan Color Rate 2013 JCM Global Corporation 13 Part No 960 000163R_Rev 2 VEGA Units Ee NOTE The Adjustment process will begin in Step 6 Do not touch the VEGA Unit while it is adjusting otherwise the adjustment will not accurately calibrate the Unit 6 Set DIP Switch Block No 2 Switch 1 to ON This action performs the Entrance Sensor s Adjustment Procedure with out Reference Paper in place NOTE Keep DIP Switch Block No 2 Switch 1 ON until prompted to turn it OFF NOTE During the adjustment process the front Panel LED will flash a Cyan Color at a high rate of speed 7 Once the Entrance Sensor s Non paper Adjustment Proce dure is complete the Front Panel LED will slowly blink at a White Light Rate 8 Set the White Reference Paper KS 325 in place 9 Set DIP Switch Block No 2 Switch 2 to ON This action performs the Validation Sensor s Adjustment using the White Reference Paper Ee NOTE Keep DIP Switch Block No 2 Switch 1 amp 2 ON until prompted to turn them OFF NOTE During the adjustment process the Front Panel LED will flash White Light at a high rate of speed 10 Once the White Reference Paper Validation Sensor Adjust ment is complete the Front Panel LED will slowly blink at a Blue Color rate Remove the White Reference Paper from the Transport Section 11 Set the Black Reference Paper KS 326 in place
Download Pdf Manuals
Related Search