PDF - Depo Racing
Contents
1. and warning 2 sound Indeed there is no sound for warning 1 3 When the sound is enabled which the warning 2 sound and key sound are turned on the gauge will buzz twice as confirmation 4 When the sound is disabled which the warning 2 sound and key sound are turned off the gauge will buzz once as confirmation 5 The gauge will return to the normal mode after 5 second of no operation activity Backlight Brightness setting There are nine level brightness sections available for each daytime and nighttime In order to set the nighttime backlight brightness the orange wire of the power wire harness should connect to dimmer 12V_ switched source 1 When the warning light and peak light are flashing alternately press lt PEAK gt to brighten the backlight while press lt SET gt to weaken the brightness 2 When the gauge is in the Backlight Brightness setting and Dimmer 12V switched source is off the daytime brightness can be selected 3 When the gauge is in the Backlight Brightness setting and Dimmer 12V switched source is on the nighttime brightness can be set 4 The gauge will return to the normal mode after 5 second of no operation activity2. as confirmation 4 After 3 second of no operation activity the gauge will return to the normal mode 3 SETTING MODE There are three functions to be operated in this mode warning sound and backlight brightness Hold lt SET gt to enter into the Warning 1 setting Warning 2 setting Sound setting and Backlight Brightness setting in sequence until the function setting you prefer is presented When the needle light is flashing the setting can be programmed Warning 1 setting 1 When the warning light is flashing the warning 1 value can be programmed Press lt PEAK gt to move the needle clockwise while press lt SET gt to move the needle counter clockwise 2 Hold either lt PEAK gt or lt SET gt to shift the needle in major increments in their representative directions 3 The gauge will return to the normal mode after 5 second of no operation activity Warning 2 setting 1 When the warning light is on the warning 2 value can be programmed Press lt PEAK gt to move the needle clockwise while press lt SET gt to move the needle counter clockwise 2 Hold either lt PEAK gt or lt SET gt to shift the needle in major increments in their representative directions 3 The gauge will return to the normal mode after 5 second of no operation activity Sound setting 1 When the warning light and the peak word are lighted up press lt PEAK gt to enable the sound while press lt SET gt to disable the sound 2 There are only key sound
3. INSTALLATION INSTRUCTIONS STEPMOTOR MOVMENT JAPAN TACHOMETER wrwarninc amp PEAK WHITE AMBER LED DISPLAY BEFORE YOU START Read instructions completely before installation NOTE It may be necessary to reprogram your radio 2 Install tachometer only when engine is cool and clock etc after reconnecting the battery ignition is off 6 Make sure mounting location does not impair visibility of 3 Make sure all necessary tools materials and interfere with driving Also check behind the mounting parts are on hand location for any wiring or components before drilling 4 Refer to your vehicle s service manual for the location 7 When connecting electrical wire install crimp terminals of tachometer sensor port vacuum system and or and make wire splices as needed ALWAYS insulate wire charging system splices with electrical tape to prevent shorting 5 Disconnect negative battery cable before installing 8 Follow all necessary safety procedures for protection tachometer ENGINE CYLINDER SELECTION The tachometer is designed for use with 1 2 3 4 5 6 7 8 9 Cylinder engines only The cylinder select switch on the rear of the tachometer must be set prior to installation Use your finger of a small screwdriver to slide the cylinder select switch To the appropriate position 1 2 3 4 5 6 7 8 or 9 MOUNTING You can mount your tachometer on or under the dashboard or on the center console according to your personal choice Determi
4. ne best position for good visibility before drilling screw holes 4 TACHOMETER CONNECTION Connect power wire RED to 12V battery wire 5 Secure lead wires along their route to prevent damage 2 Connect power wire WHITE to a switched 12V from sharp edges moving parts or hot engine circuit at fuse box or splice into any vehicle harness components wire which is energized ONLY when ignition key is 6 Turn on ignition DO NOT START ENGINE tachometer ON RUN position pointer should rotate to minimum or 0 when ignition 3 Connect power wire BLACK to ground negative is turned on battery terminal or a good chassis ground 7 Start and run engine REV engine several times and 4 Connect power wire ORANGE to panel lights circuit verify tachometer indication changes as rpm increases at fuse box or splice into any vehicle harness wire and decreases Make sure tachometer pointer operation connected to the panel lights circuit is smooth and even Control box wire harness SCHEMATIC Engine cylinder selection warning light wire harness RED power wire harness power wire harness WHITE either side is ok BLACK ORANGE INSTALLATION INSTRUCTIONS STEPMOTOR MOVMENT JAPAN TACHOMETER wrwarninc amp PEAK WHITE AMBER LED DISPLAY Tachometer signal wire connections vary with vehicle make model and ignition type Typical tachometer signal source locations are shown in the accompanying illustrations Always consult the
5. service manual for the vehicle you working on to ensure proper connection Connector for sensor wire RPM SIGNAL WIRE ECU ENGINE COMPUTER UNIT 6 TACHOMETER ASSEMBLY xternal warning light OPERATION INSTRUCTION H ef WARNING IT IS DANGEROUS TO OPERATE THE SETTING OF THE GAUGE WHEN YOU ARE DRIVING CONSIDERING YOUR AND OTHERS SAFETY PLEASE OPERATE THE SETTING BEFORE DRIVING There are three modes which can be operated BACKLIGHT MODE PEAK MODE and SETTING MODE In the setting mode there are three functions to be operated warning sound and backlight brightness Press lt SET gt to select the backlight color and lt PEAK gt to enter the peak mode when the gauge is in the normal mode Hold lt SET gt for 3 second to enter into the Warning 1 setting Warning 2 setting Sound setting and Backlight Brightness setting in sequence when the gauge is in the normal mode BACKLIGHT MODE 1 There are two different colors LED backlight in one gauge White and Amber 2 Press lt SET gt to change the backlight color when the gauge is in the normal mode 2 PEAK MODE 1 Press lt PEAK gt to enter into the Peak Mode which you can see the needle shifts to the recorded peak value and the word PEAK is lighted up 2 When the peak value is displayed hold lt PEAK gt for 3 second to clear the previous peak value which you will see the word PEAK is flashing 3 When the peak value is clear the gauge will buzz
Download Pdf Manuals
Related Search