Kimba neo - Ottobockdoc.se
Contents
1. 4 2 1 Maintenance Schedule Outdoor Mobility Base Maintenance Schedule Kimba neo outdoor mobility base Customer tem Area Inspection checklist Serial number Function setting depending on equipment Caster wheels Tyres wear Air pressure only with pneumatic tyres Fork caster wheel axles Swivel lock mechanism Running behaviour of the wheels concentricity Rear wheels Tyres wear Air pressure only with pneumatic tyres Bearings Quick release lock Running behaviour of the wheels concentricity i Seat adapter seat Ratchet mechanism adjustment Screw connections inspected Inspected for dam age deformation Seat adapter Porter cylinder Porter cylinder ease of operation Angle adjustment lock Bowden cable Stability Spring tension Suspension rear wheel linkage with wheel lock Mounting points Wheel lock mechanism Wheel lock operation Frame Rivet joints screw connections Mounting points Folding tube fixed tube head Folding mechanism Push bar Ratchet Joints Angle adjustment Push bar cover Accessories z Swragebag x lx Do the wheelchair settings match the user s requirements The maintenance service was performed by For some components rivet joints or attachment checked 40 Ottobock Kimba neo Appendices 4 2 2 Seating Unit Maintenance Schedule Maintenance Schedule Kimba neo multifunctional seating Customer unit2. 10 Use the mounting screw to install the knob including back securing bolt see Fig 85 Pos 4 on the clamp tie bar 11 12 13 14 Reinstall the back frame see Page 29 Install the back insert see Page 26 Pull the covers over the supports with proper alignment see Page 24 Reattach and close the backrest pad see Page 24 St ut CU 3 6 6 Options Accessories 3 6 6 1 Replacing Retrofitting Safety Belts and Positioning Systems For the installation of the following add on components see the Instructions for Use Qualified Personnel order number 647G771 e Safety belts Strap guide Lap belt Four point belt Five point belt e Positioning aids Abductor Chest and shoulder support Fixation vest Groin strap Hook and loop foot straps Pelvic band for installation information consult the instructions that come with the product Kimba neo Ottobock 37 Service Work 3 6 6 2 Replacing Retrofitting other Options For the installation of the following options see the Instructions for Use Qualified Personnel order number 647G771 e Canopy adapter e Summer winter slipsack e Anti slip lining e Neck support e Lumbar pad e Padding For the installation of the following options see the Instructions for Use User order number 647G770 e Canopy e Rain cover e Armrests e Grab rail Tray e Cup holder e Buggy Board e Incontinence cover e Foo
3. Install the Porter cylinder with the mounting materials provided see Fig 18 Note the following Apply oil grease to the bearing journal prior to installation see Fig 18 Pos 1 The piston rod of the Porter cylinder must not be lubricated see Fig 18 Pos 2 Note the Bowden cable guide between the seat adjustment mechanism and the Porter cylinder see Fig 19 Pos 1 Conduct a functional test Pay particular attention to the functionality of the seat tilt feature and the seat tilt mechanism in the tilted position 12 Ottobock Service Work 3 5 3 2 Replacing the Seat Adapter Tilt Activation on Standard Seat INFORMATION When replacing the seat adapter the Bowden cable also has to be replaced It is included with the mounting materials provided with the seat adapter see Fig 23 1 Remove the Bowden cable on the Porter cylinder see Page 12 2 Unlock and remove the spring folding bolt on the porter cylinder see Page 12 3 Remove the Bowden cable on the seat adapter see Fig 20 Pos 1 4 Loosen the mounting screw on one side of the seat adapter see Fig 21 Pos 1 5 Remove the screw insert a mounting aid M8 screw with counter nut in place of the screw that was removed and install the counter nut see Fig 22 Pos 1 6 Loosen the mounting screw on the other side 7 Remove the disassembly aid 8 Remove and replace the seat adapter 9 Install the seat adapter with the mou
4. Item Inspection checklist Serial number Function setting depending on eguipment Surface wear Screw connections inspected Inspected for dam age deformation Pads covers x Closures Back frame Angle adjustment clamping Back insert Knob attachment function Clamp tie bar Tilt activation mechanism Bowden cable Footplate Height setting Footplate lock Knee angle assembly Depth adjustment Angle adjustment Struts clamping lever Base frame seat frame Clamping of the knee angle assembly Ouick release lock Seat angle adjustment activation mechanism Bowden cable Seat adapter engages audibly Standard supports Width adjustment Padding Accessories 7 Tripod springs locking mechanism Grab rail padding for Tripod springs locking mechanism grab rail Surface wear Pelvic band Toothed belt locking mechanism Canopyicanopy Angle adjustment ed adapter Plug connection to the adapter x X Ratchet function x x x x Tray Tripod springs locking mechanism Angle adjustment Depth adjustment Thoracic supports Width adjustment Height adjustment Chest and shoulder Attachment buckles Belts 4 5 point Attachment and strap guide buckles Seams belting Buckle Depth adjustment Do the wheelchair settings match the user s requirements The maintenance service was performed by Kimba neo Ottobock 41 42 Ottobock Kim
5. Bowden cable from the seat adapter see Fig 20 Unlock and remove the spring folding bolt on the Porter cylinder see Fig 17 item 1 Loosen the mounting screws between the folding tubes and fixed tube heads see Fig 38 item 1 and remove the unit consisting of the folding tubes and push bar Remove and replace the front frame see Fig 40 Install the front frame with the mounting materials provided 10 Tighten the mounting screws see Fig 38 item 1 see Fig 39 item 2 3 11 Reconnect the seat adapter Bowden cable and the seat adapter Porter cylinder see Page 13 12 Install the caster wheels see Page 10 ff 3 5 5 4 Replacing the Folding Tube Bore out the rivet between the folding tube and ratchet joint see Fig 41 Pos 1 and remove the ratchet joint SI S I 2 18 Loosen the mounting screws on the suspension see Fig 41 Pos 2 Loosen the mounting screws between the folding tube and fixed tube head see Fig 41 Pos 3 Replace the folding tube Install the folding tube with the mounting materials provided see Fig 42 Tighten the mounting screws see Fig 41 Pos 2 3 Rivet the ratchet joint to the folding tube see Fig 41 Pos 1 Attach the sticker to the folding tube Ottobock Kimba neo Service Work 3 5 5 5 Replacing the Fixed Tube Head 1 Loosen the mounting screws on the suspension see Fig 24 Pos 1 2 Loosen the mounting screws between the folding tu
6. Read the service manual before starting work Familiarise yourself with the functions of the product prior to inspection and use In order to do so you can request this service manual and other documentation from the manufacturer see the overview of national Ottobock branches on the inside of the back cover or download from our homepage www ottobock de or www ottobock com Clean and disinfect the product before commencing service work Observe all care instructions and product specific inspection instructions in the instructions for use Many screw connections utilise screws and nuts equipped with thread lock If you loosen screw connections be sure to replace the respective nut or screw with one equipped with a new thread lock If new screws or nuts with thread lock are not available apply a medium strength liquid thread locking compound such as Loctite 241 or Euro Lock A24 20 to the existing screws 3 2 Instructions for Adjustment A WARNING Failure to verify tipping resistance Risk of the user falling or tipping over gt Changing the settings can lead to instability of the system as a whole Verify tipping resistance after any changes to the settings The sections that follow describe the replacement and retrofitting of standard and option parts on the product shown on the cover 8 Ottobock Kimba neo Service Work All instructions concerning the adjustment of the parts installed are included in the Instructions for
7. seat tilt feature on frame Front lashing ring 9 Rear lashing ring EE 7 6 Ottobock Kimba neo Plug on rear wheel Adjustable push bar Plug on fixed front wheel 6 Release handle folding mechanism Front lashing ring Suspension Seat adapter 8 Rear lashing ring 2 Safety 2 1 Explanation of Warning Symbols Warnings regarding possible risks of severe accident or injury Warnings regarding possible risks of accident or injury Safety NOTICE Warnings regarding possible technical damage Kimba neo Ottobock 7 Service Work 2 2 General Safety Instructions A CAUTION Failure to observe installation instructions Pinching crushing due to installation errors gt Do not reach between force actuated surfaces during installation work A CAUTION Use of unsuitable tools Pinching crushing or damaging the product gt When working use only tools that are suitable for the conditions at the workplace and whose proper use ensures safety and health protection A CAUTION Re use of self locking nuts Unintended loosening of the screw connections gt Always replace self locking nuts with new self locking nuts after disassembly NOTICE Tipping or falling of the product Damage to the product b When you work on the product secure it so that it cannot tip over or fall over gt Use a clamping device to secure the product for all work at a workbench 3 Service Work 3 1 General Information
8. 114 Norrk ping Sweden T 46 11 280600 F 46 11 312005 info ottobock se www ottobock se Otto Bock Slovakia s r o R ntgenova 26 851 01 Bratislava 5 Slovak Republic T 421 2 32 78 20 70 F 421 2 32 78 20 89 info ottobock sk www ottobock sk Otto Bock Sava d o o Industrijska bb 34000 Kragujevac Republika Srbija T 381 34 351 671 F 381 34 351 671 info ottobock rs www ottobock rs Otto Bock Ortopedi ve Rehabilitasyon Teknigi Ltd Sti Ali Dursun Bey Caddesi Lati Lokum Sokak Meric Sitesi B Block No 6 1 34387 Mecidiyek y Istanbul Turkey T 90 212 3565040 F 90 212 3566688 info ottobock com tr www ottobock com tr Africa Otto Bock Alg rie E U R L 32 rue Ahc ne Outaleb Coop rative les Mimosas Mackle Ben Aknoun Alger DZ Alg rie T 213 21 913863 F 213 21 913863 information gottobock fr www ottobock fr Otto Bock Egypt S A E 28 Soliman Abaza St Mohandessein Giza Egypt T 202 330 24 390 F 202 330 24 380 info ottobock com eg www ottobock com eg Otto Bock South Africa Pty Ltd Building 3 Thornhill Office Park 94 Bekker Road Midrand Johannesburg South Africa T 27 11 312 1255 info southafrica ottobock co za www ottobock co za Americas Otto Bock Argentina S A Av Belgrano 1477 CP 1093 Ciudad Aut noma de Buenos Aires Argentina T 54 11 5032 8201 5032 8202 atencionclientes ottobock com ar www ottobock com ar Otto Bock do Brasil Tecnica Ortopedic
9. 4901 bockuk ottobock com www ottobock co uk Otto Bock Hungaria Kft Tatai ut 74 1135 Budapest Hungary T 36 1 4511020 F 36 1 4511021 info ottobock hu www ottobock hu Otto Bock Adria d o o Dr Franje Tu mana 14 10431 Sveta Nedelja Croatia T 385 1 3361 544 F 385 1 3365 986 ottobockadria ottobock hr www ottobock hr Otto Bock Italia Srl Us Via Filippo Turati 5 7 40054 Budrio BO Italy T 39 051 692 4711 F 39 051 692 4720 info italia ottobock com www ottobock it Otto Bock Benelux B V Ekkersrijt 1412 5692 AK Son en Breugel The Netherlands T 31 499 474585 F 31 499 476250 info benelux ottobock com www ottobock nl Industria Ortop dica Otto Bock Unip Lda Av Miguel Bombarda 21 2 Esq 1050 161 Lisboa Portugal T 351 21 3535587 F 351 21 3535590 ottobockportugal mail telepac pt Otto Bock Polska Sp z o o Ulica Koralowa 3 61 029 Poznan Poland T 48 61 6538250 F 48 61 6538031 ottobock ottobock pl www ottobock pl Otto Bock Romania srl Sos de Centura Chitila Mogosoia Nr 3 077405 Chitila Jud Ilfov Romania T 40 21 4363110 F 40 21 4363023 info ottobock ro www ottobock ro OOO Otto Bock Service p o Pultikovo Business Park Greenwood Building 7 69 km MKAD 143441 Moscow Region Krasnogorskiy Rayon Russian Federation T 7 495 564 8360 F 7 495 564 8363 info ottobock ru www ottobock ru Otto Bock Scandinavia AB Koppargatan 3 Box 623 60
10. Fig 98 3 Remove and replace the sliders 4 Tighten the mounting screws on the sliders to a torque of 5 Nm Kimba neo Ottobock 31 Service Work Replacing the Flange Nut on a Slider 1 Loosen the mounting screws in the sliders see Fig 97 Pos 1 2 Remove the inserted flange nuts see Fig 97 Pos 2 from the sliders and replace them 3 Secure the flange nuts with the mounting screws 3 6 3 3 Replacing the Knee Angle Assembly Complete 1 Remove the seating unit from the outdoor mobility base 2 Loosen the 2x knurled nuts on the underside of the base frame see Fig 99 Pos 1 3 If required Loosen the 2 x knurled nuts on the rear mounting screws on the hip supports see Fig 111 4 Pull the knee angle assembly complete out of the base frame and replace it see Fig 100 5 Remove the footplate from the footplate adapter see Page 31 6 Slide the knee angle assembly complete back into the base frame and mount it 7 Slide the footplate onto the footplate adapter see Page 31 8 Hand tighten the knurled nuts 3 6 3 4 Replacing the Footplate Adapter 1 Remove the footplate see Page 31 2 Remove the knee angle assembly from the base frame see Page 32 3 Loosen the pivoted levers see Fig 101 Pos 1 from the end pieces of the seat adjuster see Fig 101 Pos 2 4 Open the clamping lever see Fig 101 Pos 3 and pull the footplate adapter bsee Fig 101 Pos 4 from the struts s
11. Use qualified personnel see the section Foreword for the order number 3 3 Maintenance Schedule Maintenance schedule as a template for copying see Page 40 3 4 Required Tools and Accessories The following tools are required in order to perform the service work e Reversible ratchet handle wrench and sockets size 8 24 e Torque wrench measurement range 5 50 Nm e Wrench size 8 24 e Allen wrench size 2 5 6 e Screwdriver blade width 2 5 3 5 5 mm e Phillips head screwdriver size 2 e Hammer approx 300 g soft faced hammer e Pliers cutting pliers combination pliers snap ring pliers e Rivet gun for rivets up to 85 mm e Pin punch e 3 4 5 6 mm e Drill twist drill 3 2 5 5 2 6 mm e Stanley knife with sickle hooked blade and standard blade e Tyre mounting levers and inner tube repair kit e Workbench and vice with plastic jaws and rubber insert e Measurement equipment rule spirit level e Liquid thread locker medium and strong 1 Included in 481C08 STO10 Tool Set 2 Size 3 6 contained in the 481C08 STO10 Tool Set 3 5 Outdoor Mobility Base 3 5 1 Rear Wheels 3 5 1 1 Replacing the Rear Wheel 1 Release the wheel lock 2 Press down the lock on the rear wheels see Fig 4 3 Replace and reinstall the wheel The locking mechanism must engage audibly 3 5 1 2 Replacing the Casing Replacing the casing on the rear wheel see Fig 6 Pos 1 corresponds to replacing the casing
12. a Ltda Alameda Maria Tereza 4036 Bairro Dois C rregos 13278 181 Valinhos S o Paulo Brasil T 55 19 3729 3500 F 55 19 3269 6061 ottobock ottobock com br www ottobock com br Otto Bock HealthCare Canada 5470 Harvester Road Burlington Ontario L7L 5N5 Canada T 41 289 288 4848 F 1 289 288 4837 infocanada ottobock com www ottobock ca Otto Bock HealthCare Andina Ltda Calle 138 No 53 38 Bogot Colombia T 57 18619988 F 57 1 8619977 info ottobock com co www ottobock com co Otto Bock de Mexico S A de C V Prolongaci n Calle 18 No 178 A Col San Pedro de los Pinos C P 01180 M xico D F Mexico T 52 55 5575 0290 F 52 55 5575 0234 info ottobock com mx www ottobock com mx Otto Bock HealthCare Two Carlson Parkway North Suite 100 Minneapolis MN 55447 USA T 1 763 553 9464 F 1 763 519 6153 usa customerservice ottobockus com www ottobockus com Asia Pacific Otto Bock Australia Pty Ltd Suite 1 01 Century Corporate Centre 62 Norwest Boulevarde Baulkham Hills NSW 2153 Australia T 61 2 8818 2800 F 61 2 8814 4500 healthcare ottobock com au www ottobock com au Beijing Otto Bock Orthopaedic Industries Co Ltd B12E Universal Business Park 10 Jiuxiangiao Road Chao Yang District Beijing 100015 P R China T 8610 8598 6880 F 8610 8598 0040 news service ottobock com cn www ottobock com cn Otto Bock Asia Pacific Ltd Unit 1004 10 F Greenfield Tower Concordia P
13. ar VIE B ee ee nern 9 POD AGING Te ASING ala aa LOU Oa nek Nb ban Nisan 9 Replacing the Tube Pneumatic Tyre ercscvemaccete rote stencaas enam a rab ag Jana ee 9 PONT na 10 Iseplacing a Fred Froni he ee Kel na on anon 10 Replacing a Swivelling Front Wheel sa een 10 Replac ng el a ler Folk een ee ee 10 Repnlacing ne SWING oo NP 11 Replacing Ihe CASING TESTEN EE OT LOU LO T oem 11 Replacing wie Tube TP Bede TUB aeui Edita er en eer ee ee uM eM opu EE 12 Sean Ada OB sian T 12 Replacing the Seat Adjustment Mechanism Porter Cylinder esee 12 Replacing the Seat Adapter Tilt Activation on Standard Seat cccccececeeeeeeeeeeeeeeeeeeeeeeeneaeeeeeeneaeaeanenenees 13 Suspension Resr Wheel Linkage sisi ciis So pedes snap amati enden 14 Kepang SION ee ea DD DOE 14 Adj sting the SUSPENSION ee ee een 14 Replacing the Complete Rear Wheel Linkage incl Wheel Lock 15 Replacing the Rear Wheel Linkage Individual anne da 15 gi ct t 16 PR NC Ie Fron RM oiii oa ee uitio tU te E eier 16 Replacing ne Upper Front mU TT T i o I TEE 17 Replacing ihe Front Frame Complete ee ee o TO OOo 18 REDIAC ING ne FO ln Uo ee ee er EE ee 18 Replsoing tne Fed TUDE Head essen nee u u ee ee 19 IESU I IT ee ee ee 20 Replacing the Ratchet Joints with Folding Fixture en nee ee ee ee 20 BRE
14. ba neo Kundenservice Customer Service Europe Otto Bock HealthCare Deutschland GmbH Max Nader Str 15 37115 Duderstadt Germany T 49 5527 848 3433 F 49 5527 848 1460 healthcare ottobock de www ottobock de Otto Bock Healthcare Products GmbH Kaiserstra e 39 1070 Wien Austria T 43 1 5269548 F 43 1 5267985 vertrieb austria ottobock com www ottobock at Otto Bock Adria Sarajevo D O O Omladinskih radnih brigada 5 71000 Sarajevo Bosnia Herzegovina T 387 33 766200 F 387 33 766201 obadria bih net ba www ottobockadria com ba Otto Bock Bulgaria Ltd 41 Tzar Boris Ill Blvd 1612 Sofia Bulgaria T 359 2 80 57 980 F 359 2 80 57 982 info ottobock bg www ottobock bg Otto Bock Suisse AG Pilatusstrasse 2 CH 6036 Dierikon T 41 41 455 61 71 F 41 41 455 61 70 suisse ottobock com www ottobock ch Otto Bock CR s r o Protetick 460 33008 Zru amp Senec Czech Republic T 420 377825044 F 420 377825036 email ottobock cz www ottobock cz Otto Bock Iberica S A C Majada 1 28760 Tres Cantos Madrid Spain T 34 91 8063000 F 34 91 8060415 info ottobock es www ottobock es Otto Bock France SNC 4 rue de la R union CS 90011 91978 Courtaboeuf Cedex France T 433 1 69188830 F 33 1 69071802 information gottobock fr www ottobock fr Otto Bock Healthcare plc 32 Parsonage Road Englefield Green Egham Surrey TW20 OLD United Kingdom T 44 1784 744900 F 44 1784 74
15. bes and fixed tube heads see Fig 38 Pos 1 and remove the unit consisting of the folding tubes and push bar 3 Using a spiral bit 9 5 mm bore out the rivet on the fixed tube head and tap it out with a pin punch 3 mm see Fig 43 4 Tap out the fixed tube head from the upper front frame and replace it see Fig 44 NOTICE Damage to the fixed tube head Only use the surface shown in the illustration for tapping the component in or out 5 Using apin punch press the fixed tube head into the upper front frame see Fig 45 6 Rivet the fixed tube head see Fig 46 7 Reinstall the folding tubes with push bar and the suspension 8 Tighten the mounting screws see Fig 38 Pos 1 see Fig 24 Pos 1 Kimba neo Ottobock 19 Service Work 3 5 6 Push Bar 3 5 6 1 Replacing the Ratchet Joints with Folding Fixture 1 Using a spiral bit O 5 mm bore out 4 rivets on each ratchet joint and tap them out with a pin punch 3 mm see Fig 47 Pos 1 2 2 Remove and replace the ratchet joints see Fig 48 3 Rivet the ratchet joint with the folding fixture on the correct side see Fig 49 3 5 6 2 Replacing the Push Bar 1 Using a spiral bit O 5 mm bore out 2 rivets on each ratchet joint and tap them out with a pin punch 3 mm see Fig 47 Pos 1 2 Remove and replace the push bar see Fig 50 3 Rivet the push bar onto the ratchet joint 3 5 7 Options Accessories 3 5 7 1 Replacing
16. cing the Casing 1 Remove the wheel see Page 10 and let out the air if required 2 Using a tyre lever remove the casing from the rim see Fig 13 3 Remove the tube 4 Replace the casing see Fig 14 Pos 1 5 Fill the inner tube with a small amount of air before mounting in order to avoid damage and pinching 6 Install the casing on the rim with a tyre lever 7 Reinstall the wheel see Page 10 Kimba neo Ottobock 11 Service Work 3 5 2 6 Replacing the Tube Pneumatic Tyre STE O Remove the wheel see Page 10 and let out the air if required Using a tyre lever remove the casing from the rim see Page 11 Replace or repair the tube see Fig 14 Pos 2 see Fig 15 Fill the inner tube with a small amount of air before mounting in order to avoid damage and pinching Install the casing on the rim with a tyre lever Reinstall the wheel see Page 10 3 5 3 Seat Adapter 3 5 3 1 Replacing the Seat Adjustment Mechanism Porter Cylinder 1 SU EJ Remove the Bowden cable from the porter cylinder Cut off the cable end sleeve see Fig 16 Pos 1 Loosen the screw die Remove the spring and Bowden cable guide see Fig 16 Pos 2 3 Unthread the Bowden cable on the Porter cylinder Unlock and remove the spring folding bolt on the Porter cylinder see Fig 17 Pos 1 Remove the retaining ring see Fig 17 Pos 2 and the bearing journal Remove and replace the Porter cylinder
17. components gt Seat angle adjustment knob see Fig 81 item 1 gt Seat angle adjustment cover cap see Fig 82 item 1 gt Back angle adjustment knob see Fig 81 item 2 b Back angle adjustment cover cap see Fig 82 item 2 Replacing the Seat Angle Adjustment Knob and Cover Cap 1 Using a screwdriver carefully pry up the cover cap remove and replace it see Fig 83 Remove and replace the circlip see Fig 84 Pull the knob off the centring pivot and replace it AUN Install the knob using the mounting materials provided see Fig 81 item 1 Tap the cover cap see Fig 82 item 1 into the knob Ol Kimba neo Ottobock 27 Service Work Replacing the Back Angle Adjustment Knob and Cover Cap 1 Using a screwdriver carefully pry up the cover cap remove and replace it not illustrated Unscrew the knob from the mounting screw on the clamp tie bar and replace it see Fig 117 item 1 3 3 Reinstall the knob see Fig 81 item 2 Using a rubber hammer tap the cover cap see Fig 82 item 2 into the knob 3 6 2 3 Removing Installing the Tilt Activation Mechanism INFORMATION Removing installing the tilt activation mechanism is required to replace the back frame and base frame seat Removing the Tilt Activation Mechanism 1 Remove the backrest pad see Page 24 Remove the back insert see Page 26 3 Remove the cover cap and knob see preceding section Pry th
18. e Seat Frame 3 6 4 1 Replacing the Base Frame Tilt Activation Mechanism on Seat INFORMATION The tilt activation mechanism must be removed prior to replacement see Page 28 1 Remove the seat pad see Fig 70 2 Remove the seating unit 3 Loosen the 4 x knurled nuts on the underside of the seat see Fig 111 Pos 1 and remove the hip supports 4 Pull the knee angle assembly out of the base frame see Fig 104 5 Remove the back insert see Page 26 6 Remove the Bowden cable of the tilt activation mechanism from the back frame see Page 28 7 Loosen the 4 x mounting screws on the back frame base frame connection see Fig 104 Pos 1 2 8 Remove and replace the base frame see Fig 105 9 Mount the back frame on the base frame see Fig 104 Pos 1 2 see Page 29 10 Reinstall the Bowden cable of the tilt activation mechanism see Page 28 11 Reinstall the back insert see Page 26 12 Reinstall the backrest pad see Page 24 Kimba neo Ottobock 33 Service Work 3 6 5 Supports 3 6 5 1 Replacing the Headrest Supports 1 E I 8 9 With a standard pad Open the zipper at the top of the pad see Fig 70 and fold the backrest pad forward With a microfibre pad Open the zipper Do not fold down the pad the supports must be threaded through the slits in the pad for installation Loosen the knurled nuts on the back of the back plate see Fig 106 Remove the mounting screws and suppor
19. e see Fig 64 item 2 PS EA E AX S We NC NE N NAN Ne c 3 6 Multifunctional Seating Unit Standard Seat 3 6 1 Pads Covers The manufacturer offers two versions of the pads and covers with identical mounting b Pads covers standard b Pads covers microfibre 3 6 1 1 Replacing the Seat Pad 1 Lift the seat pad and remove it from the hook and loop fastener on the seat plate see Fig 65 2 Replace the seat pad 3 Fit the seat pad onto the hook and loop fastener I Push the seat pad under the hip supports see Fig 66 Kimba neo Ottobock 23 Service Work 3 6 1 2 Replacing the Backrest Pad The manufacturer offers two versions of the backrest pad gt Back pad for standard back insert see Fig 67 gt Back pad for back insert with head supports see Fig 68 to adjust the clearance of the integrated head sup port see Page 26 Release the twist lock of the backrest pad behind the seat bottom see Fig 69 Unzip the backrest pad zipper see Fig 70 and remove replace the backrest pad Put the backrest pad in place and pull it through between the back and seat bottom Close the twist lock see Fig 69 Slide the backrest pad under the lateral supports no illustration m Ol 3 6 1 3 Replacing the Covers The manufacturer offers the covers in the following versions Covers for headrest supports see Fig 71 Pos 1 Covers for lateral supports see Fig 71 Pos 2 Covers f
20. e back of the Bowden cable adapter see Fig 86 Pos 1 off the adapter on the back plate see Fig 86 Pos 2 5 Remove the round piece from the Bowden cable adapter see Fig 87 Pos 1 6 If required disconnect the Bowden cable from the round piece see Fig 87 Pos 2 7 Cutopen and remove the cable ties on the back frame see Fig 88 Pos 1 8 Pull the Bowden cable down through the back frame see Fig 89 Pos 1 Now the back frame and base frame seat frame can be replaced Installing the Tilt Activation Mechanism 1 After installing the back frame or base frame seat frame reinstall the tilt activation mechanism 2 Note the following With the help of cable ties install the Bowden cable so that it cannot be pinched damaged see Fig 88 see Fig 89 28 Ottobock Kimba neo Service Work During assembly firmly press the Bowden cable adapter into the adapter on the back plate see Fig 86 Pos 1 2 3 6 2 4 Replacing the Back Frame Complete en uer mu Iu CO 9 Remove the backrest pad see Page 24 Remove the back insert see Page 26 Remove the tilt activation mechanism see Page 28 Loosen the 4 x mounting screws on the back frame base frame connection see Fig 90 Pos 1 2 Remove the 4 x bearing bushings see Fig 90 Pos 3 Separate the back frame from the base frame and replace it Install the back frame using the mounting materials provided see Fig 91 Tighten th
21. e mounting screws INFORMATION Tighten the screw connections so that there is no play between the mounting ele ments Take care however not to deform any components Then check the movability of the connec ted frame components and readjust the tightness of the screw connections as necessary Reinstall the tilt activation mechanism see Page 28 and the back insert see Page 26 10 Reinstall the backrest pad see Page 24 Kimba neo Ottobock 29 Service Work 3 6 2 5 Replacing the Lateral Supports To install the lateral supports see Page 36 3 6 2 6 Replacing the Headrest Supports To install the headrest supports see Page 34 3 6 2 7 Installing removing the seat depth reducer INFORMATION The seat depth of the multifunctional seating unit in size 1 can be reduced by 5 cm to 14 cm with the seat depth reducer Installing the seat depth reducer 1 Remove the covers 2 Remove the hip pads see Page 35 3 Remove the back frame In order to do so loosen the four mounting screws on the back frame base frame connection see Fig 90 item 1 2 and remove the four bearing bushings see Fig 90 item 3 4 Attach the seat depth reducer with two mounting screws and two bearing bushings to the base frame see Fig 92 item 1 see Fig 93 item 1 INFORMATION In doing so secure the mounting screws with a medium strength liquid thread lock compound see Fig 94 5 Install the back frame with two mounting screws and
22. ee Fig 101 Pos 5 5 Pull the struts from the end pieces of the seat adjuster see Fig 101 Pos 5 2 6 Prepare the new footplate adapter see Fig 102 7 Insert the struts into the end pieces of the seat adjuster see Fig 102 Pos 1 8 Slide the footplate adapter onto the struts see Fig 102 Pos 2 co Engage the clamping lever see Fig 102 Pos 3 10 Mount the pivoted levers see Fig 102 Pos 4 on the end pieces of the seat adjuster with the mounting screws see Fig 101 Pos 1 2 32 Ottobock Kimba neo Service Work 11 Mount the footplate see Page 31 12 Mount the knee angle assembly on the base frame see Page 32 3 6 3 5 Replacing the Seat Adjuster 1 Remove the footplate see Page 31 2 Remove the knee angle assembly from the base frame see Page 32 3 Loosen the footplate adapter with struts from the end pieces of the seat adjuster see Page 32 4 Replace the seat adjuster see Fig 102 Pos 5 5 Insert the struts into the end pieces of the seat adjuster see Fig 102 Pos 1 6 Slide the footplate adapter onto the struts see Fig 102 Pos 2 7 Engage the clamping lever see Fig 102 Pos 3 8 Mount the pivoted levers see Fig 102 Pos 4 on the end pieces of the seat adjuster with the mounting screws see Fig 101 Pos 1 2 9 Mount the footplate see Page 31 10 Mount the knee angle assembly on the base frame see Page 32 3 6 4 Base Fram
23. f travel Using an anti slip mat is recommended Turning the seating unit is only possible if the respirator platform installation is changed e The respirator is attached to the respirator platform using straps through the slots Kimba neo Ottobock 21 Service Work Installation with a seat facing opposite to the direction of travel 1 Glue the loop strap onto the front frame tube see Fig 57 2 Firmly install the clamp fittings on the interior bores of the large plate see Fig 58 item 1 3 Set the large plate onto the tube of the front frame see Fig 58 item 2 4 Press the clamp fittings of the large plate onto the axle tube see Fig 58 item 3 5 Setthe small plate onto the front frame tube see Fig 60 item 1 O Thread the bearing bushings through the lashing points from the outside and firmly screw them to the small plate see Fig 60 item 2 Installation with a seat facing in the direction of travel 1 Glue the loop strap onto the front frame tube see Fig 57 Pre install the metal bracket on the large plate see Fig 62 3 Setthe large plate onto the front frame tube see Fig 63 item 1 Thread the bearing bushings through the lashing points from the outside and firmly screw them to the large plate see Fig 61 see Fig 63 item 2 22 Ottobock Kimba neo Service Work 5 Set the small plate onto the front frame tube see Fig 64 item 1 6 Setthe small plate onto the axle tub
24. item 1 Only for front frame with seat adapter see Page 13 Remove the Bowden cable from the seat adapter see Fig 20 Unlock and remove the spring folding bolt on the Porter cylinder see Fig 17 item 1 Loosen the mounting screws between the folding tubes and fixed tube heads see Fig 38 item 1 and remove the unit consisting of the folding tubes and push bar Using a spiral bit 5 mm bore out 8 rivets between the lower upper front frame see Fig 33 item 3 and tap them out with a pin punch 3 mm Remove and replace the upper front frame see Fig 37 Install rivet the front frame 10 Tighten the mounting screws see Fig 38 item 1 see Fig 24 item 1 11 Only for front frame with seat adapter Reconnect the seat adapter Bowden cable and the seat adapter Porter cylinder see Page 13 12 Install the caster wheels see Page 10 ff Kimba neo Ottobock 17 Service Work 3 5 5 3 Replacing the Front Frame Complete aR DN HG O St NA Nut SA SA NAN Remove the plug on rear wheel Put the frame on its side Remove the caster wheels swivelling front wheels see Fig 39 item 1 fixed front wheels not illustrated Loosen the mounting screws between the rear wheel linkages and lower front frame see Fig 39 item 2 Loosen the mounting screws on the suspension see Fig 39 item 3 Disconnect the front frame from the seat adjustment mechanism see Page 13 Remove the
25. laza 1 Science Museum Road Tsim Sha Tsui Kowloon Hong Kong China T 852 2598 9772 F 852 2598 7886 info ottobock com hk www ottobock com Otto Bock HealthCare India Behind FairLawn Housing Society St Gregorios Lane Sion Trombay Road Chembur Mumbai 400071 India T 91 22 2520 1268 F 91 22 2520 1267 information indiaottobock com www ottobock in Otto Bock Japan K K Yokogawa Building 8F 4 4 44 Shibaura Minato ku Tokyo 108 0023 Japan T 81 3 3798 2111 F 81 3 3798 2112 ottobock ottobock co jp www ottobock co jp Otto Bock Korea HealthCare Inc 4F Agaworld Building 1857 74 Seocho dong Seocho ku 137 070 Seoul Korea T 82 2 577 3831 F 82 2 577 3828 info ottobockkorea com www ottobockkorea com Otto Bock South East Asia Co Ltd 1741 Phaholyothin Road Kwaeng Chatuchark Khet Chatuchark Bangkok 10900 Thailand T 66 2 930 3030 F 66 2 930 3311 obsea otttobock co th www ottobock co th Other countries Otto Bock HealthCare GmbH Max Nader StraBe 15 37115 Duderstadt Germany T 49 5527 848 1590 F 49 5527 848 1676 reha export ottobock de www ottobock com Ihr Fachhandler Your specialist dealer E L Versandanschrift f r R cksendungen Adress for Returns Otto Bock Manufacturing K nigsee GmbH Lindenstra e 13 07426 K nigsee Rottenbach Germany Printed by Otto Bock Mobility Solutions GmbH Lindenstra e 13 07426 K nigsee Rottenbach Germany www ottobock co
26. le MIO Eile Push BaF ae E een 20 Opo ACCOSSOHOS eee E E a E eee T 20 Replacing the Storage Baskal ee ena 20 Replacing Retrofitting the MpASSIS sieves dean oma ama bina rttr rtn slam aka iban UDSRSPS E NUES 21 Kelroring the Res PATON RIA ONN aer ee 21 Multifunctional Seating Unit Standard Seat o ome aa 23 PAGS Gor ce 23 ReBlZcingane SAN Pad Men an ee ee 23 Kepiscing IN BACK PA ae aa 10 0L E ee in 24 Rep AC ING ine CO an abi Sa Ra Ba 24 Replacing ihe Grab Rail Cover TO Oo en ee ern Rene 25 Replacing the Frame Padding Option sense ere reni ee 25 Kimba neo Table of contents 3 6 2 BE an ea es ea ea aes 26 3 95 24 keplacing ine Baek 4g an em te Mon ee aan Been en sera 26 OE S R kencing NO ee D o S EET 27 3 6 2 3 Removing Installing the Tilt Activation MeChanism cccccceee eee en emn mene 28 3 0 24 Replacing the Back Frame Complete nn nenn 29 3025 Replacing the Lateral Sup MN at 30 926 Replacing Wie Headrest lt 5 Ui Po Na si 30 3 6 2 7 Installing removing the seat depth reducer nee nenne 30 3 6 3 Footplate Knee Angle Assembly zes ee ai 31 3 03 41 REBEL Ne Foot Plate ee oa I OST 31 3 6 3 2 Replacing Small Parts on the Footplate san ne a einen 31 3 6 3 3 Replacing the Knee Angle Assembly Complete ococococekakkk aa 32 3934 Replacing ihe Footplato AOA pe ea an MU PUEDEN sa 32 3 6 3 5 Replacing ine Seat Adjuster sae Nana aa ta aon 33 3 6 4 Base Frame 583 EA Maa ad 3 6 4 1 Replacing the Base Fra
27. m Ottobock has a certified Quality Management System in accordance with ISO 13485 EN 03 1402 Ottobock 647G 796
28. me Tilt Activation Mechanism on Seat ssssssssssssssessseesenne nenn nn nenn 33 3 6 5 SPP OTS ni ana LUE 34 3 6 5 1 Replacing the Headrest SUPpOorS aa 34 36 5 2 Replacing the Thoracic Sy Donna ii 35 365 3 Replacing Ine Hip Supp Oris sos oo aa ebi aa been aa ab onani 35 3052 Replacing ine Lateral Sup le ee nee 36 3 6 6 Opo Oo SUN ES ue esatta ea ee ee ee ee Reese 37 3 6 6 1 Replacing Retrofitting Safety Belts and Positioning Systems sessssssssssessseseeeenee nene 37 3602 Replacing ReiromMing other O PON Me eier 38 4 Ae ika 39 41 Technical Dalan neon Se ai sence sinh naa itb aa anna Eee semen E ena Ea este 39 4 2 Mamienanc Shen Mes P P 40 4 2 1 Maintenance Schedule Outdoor Mobility Base ssessesessesesessssssseeeneememeneen eene 40 4 2 2 Seating Unit Maintenance Schedule 2 dius uma ceo east vectis live ee 41 Kimba neo Ottobock 3 Introduction 1 Introduction 1 1 Foreword Regular maintenance is important it improves safety and increases the lifespan of the product All Mobility products should be inspected and serviced once a year However we recommend inspecting readjusting and if necessary servicing the product every 6 months if the product is used frequently by growing children or by users with changing clinical conditions Only use original spare parts for all service and maintenance work The service and maintenance tasks desc
29. nting materials provided see Fig 23 Tighten the seat adapter mounting screws to a torque of 20 Nm 10 Conduct a functional test Pay particular attention to the functionality of the seat tilt feature and the seat tilt mechanism in the tilted position Kimba neo Ottobock 13 Service Work 3 5 4 Suspension Rear Wheel Linkage 3 5 4 1 Replacing the Suspension 1 Remove the plug on rear wheel 2 Put the frame on its side 3 Loosen the suspension mounting screws see Fig 24 Pos 1 4 Remove and replace the suspension 5 Install the suspension with the mounting materials provided see Fig 25 Tighten the mounting screws 6 To adjust the spring force see the following section 3 5 4 2 Adjusting the suspension The suspension can be adjusted continuously according to the user s weight and the conditions of the road sur face 1 Twist the adjustment rings on both sides of the frame egually see Fig 26 item 1 Clockwise the suspension becomes tighter Counterclockwise the suspension becomes softer 2 Check that the adjustment rings are positioned the same on both sides The 4 marks can be used for orienta tion see Fig 26 item 2 see Fig 27 item 1 14 Ottobock Kimba neo Service Work We recommend the following setting for the spring tension up to 10 kg up to 1st marking from the top up to 20 kg up to 2nd marking from the top up to 30 kg up to 3rd marking from the top up t
30. o 40 kg up to 4th marking from the top Reference point upper edge of the plastic adjustment nut 3 5 4 3 Replacing the Complete Rear Wheel Linkage incl Wheel Lock O1 NN Bb O Remove the plug on rear wheel Put the frame on its side Loosen the mounting screws between the rear wheel linkage and suspension see Fig 28 Pos 1 Loosen the mounting screws between the rear wheel linkage and lower front frame see Fig 28 Pos 2 Remove and replace the assembly rear wheel linkage with wheel lock see Fig 29 Install the complete rear wheel linkage using the mounting materials provided see Fig 29 Tighten the mount ing screws 3 5 4 4 Replacing the Rear Wheel Linkage Individual Remove the plug on rear wheel oo SS E 8 Put the frame on its side Loosen the mounting screw between the rear wheel linkage and suspension see Fig 30 Pos 1 Loosen the mounting screw between the rear wheel linkage and lower front frame see Fig 30 Pos 2 Loosen the mounting screw on the axle stub see Fig 30 Pos 3 Disengage and replace the rear wheel linkage see Fig 31 Pos 1 Ensure that the spring and lock bush of the wheel lock are not ejected see Fig 31 Pos 2 Install the new rear wheel linkage with the mounting materials provided see Fig 32 Ensure that the bore hole of the axle stub see Fig 31 Pos 3 fits flush with the mounting bore of the rear wheel linkage see Fig 31 Po
31. on the caster wheel see Page 11 3 5 1 3 Replacing the Tube Pneumatic Tyre Replacing the tube on the rear wheel see Fig 6 Pos 2 corresponds to replacing the tube on the caster wheel see Page 12 Kimba neo Ottobock 9 Service Work 3 5 2 Front Wheels 3 5 2 1 Replacing a Fixed Front Wheel 1 After pushing down the locking mechanism pull the front wheel off to the outside and replace it not illus trated 2 Slide on the front wheel The locking mechanism must engage audibly 3 5 2 2 Replacing a Swivelling Front Wheel 1 Putthe frame on its side 2 Remove the caster wheel axle in the caster fork see Fig 7 3 Remove and replace the caster wheel see Fig 8 4 Tighten the caster wheel axle to a torque of 9 Nm 3 5 2 3 Replacing the Caster Fork 1 Remove the caster wheel see the preceding section 2 Loosen the caster fork mounting screw see Fig 9 3 Remove and replace the caster fork see Fig 10 4 Install the caster fork with the supplied mounting materials 5 Tighten the caster fork to a torque of 25 Nm 10 Ottobock Kimba neo Service Work 3 5 2 4 Replacing the Swivel Lock Remove the caster wheel and caster fork see the preceding sections see Fig 11 EY 2 Slide the swivel lock off the front frame and replace it see Fig 12 3 Slide the swivel lock onto the front frame 4 Install the caster fork and caster wheel see the preceding section 3 5 2 5 Repla
32. or thoracic supports no illustration Cover for the grab rail see Fig 71 Pos 3 see the following section for replacement Covers for hip supports see Fig 71 Pos 4 Cover for the abductor see Fig 71 Pos 5 1 Remove the seat pad or backrest pad if required 2 Open the hook and loop closure on the cover 3 Remove the cover from the support or abductor and replace it 4 Slide the cover over the support with proper alignment Note the following If present position the side reinforced with foam material on the outside over the screw heads see Fig 72 Pos 1 24 Ottobock Kimba neo Service Work Pull the cover over the support starting with the side that does not have a lug see Fig 73 Pos 1 Pull the cover over the support with the help of the lug see Fig 73 Pos 2 Before fastening the hook and loop closure push and fold down the lug see Fig 74 5 Putthe seat pad or backrest pad back into place 3 6 1 4 Replacing the Grab Rail Cover Option 1 Pushin the tripod spring and remove the grab rail see Fig 75 Pos 1 2 Pull the grab rail pad see Fig 71 Pos 3 off the grab rail and replace it 3 Slide the grab rail pad onto the grab rail see Fig 75 4 Reattach the grab rail 3 6 1 5 Replacing the Frame Padding Option 1 Open the hook and loop closure on the frame padding 2 Remove and replace the frame padding 3 Fitthe frame padding around the push bar and cl
33. ose the hook and loop strap Kimba neo Ottobock 25 Service Work 4 Twist the hook and loop strap down and push the frame padding over the folding mechanism all the way to the release handles see Fig 76 3 6 2 Back 3 6 2 1 Replacing the Back Insert INFORMATION The manufacturer offers two versions of the back insert Standard back insert see Fig 78 Back insert with head supports see Fig 79 Remove the backrest pad see Page 24 Loosen the 2 x set screws on the backrest tubes see Fig 77 Pos 1 3 Remove and replace the standard back insert see Fig 78 or the back insert with head supports see Fig 79 Slide the new back insert into the back frame and adjust it to the desired height Tighten the set screws see Fig 77 Pos 1 INFORMATION You can achieve a greater back height by additionally shifting the top back plate at the back insert To do so loosen remove the knurled nuts shift the back plate and hand tighten the knurled nuts again 6 Put the backrest pad in place see Page 24 Adapting the Back Insert with Integrated Head Supports To adjust the clearance in the area of the head up to 3 foam pads with a thickness of 1 cm each can be glued onto the head supports see Fig 80 Pos 1 They are included with the backrest pad em 26 Ottobock Kimba neo Service Work 3 6 2 2 Replacing the Knob The manufacturer offers the knob and cover cap in the following single
34. ottobock Kimba neo Service Manual Table of contents Table of contents 1 1 1 2 1 3 2 1 2 2 3 1 3 2 3 3 3 4 3 5 3 9 1 3 5 1 1 3 5 1 2 3 5 1 3 3 5 2 3 5 2 1 3 5 2 2 3 5 2 3 3 5 2 4 3 5 2 5 3 5 2 6 3 5 3 3 5 3 1 3 5 3 2 3 5 4 3 5 4 1 3 5 4 2 3 5 4 3 3 5 4 4 3 5 5 3 5 5 1 3 5 5 2 3 5 5 3 3 5 5 4 3 5 5 5 3 5 6 3 9 6 1 3 5 6 2 3 5 7 3 5 7 1 3 5 7 2 3 5 7 3 3 6 3 6 1 3 6 1 1 3 6 1 2 3 6 1 3 3 6 1 4 3 6 1 5 2 Ottobock IntroO Oa ta aa aaa aa a aaa iaaa aaa aia aaki 4 FORO Ora 4 SUP C 4 Prod ct CO 7 7 5 ctr me 7 Explananon or Warning San aer 7 General aren Asi OS ae eee TO C E ee ee eee esai 8 Service WORK E E E E ombak 8 General Monna iON zen ee ne ai ee ae aa a E e eai 8 msmuchons Tor AGJUSIM ON sas iisos s pani osa Us rop na ra nU RR RR ian ERR a hR aian Aa euere 8 Maintenance Sschsdule a oo mus ep odia anak Mia nekad D ER Urb ena aa Pax a ES sU bec ERE 9 Regurea Lols and Ace te ba 9 Gurdoor Mobili m MEER TEE OT EDU 9 Roar WINGS E 9 Kep eter ale qe Re
35. ribed here should only be completed by trained qualified personnel and not by the user of the device This service and maintenance manual refers to the respective spare parts catalogues and the instructions for use of the described products Please use these documents together Use the maintenance schedule checklist as a template for making copies Retain completed maintenance sched ules and provide the customer with a copy Instructions for Use Qualified Per Instructions for Use User sonnel Kimbano 6767715 GATGTTO 1 2 Support Your national Ottobock team will be happy to answer any technical questions The contact addresses and tele phone numbers can be found on the back inside cover of the service manual 4 Ottobock Kimba neo Introduction 1 3 Product Overview Kimba Neo outdoor mobility base with multifunctional seating unit and swiveling front wheels option Plug on rear wheel 6 Angle adjustable backrest Swiveling front wheel option Adjustable push bar Front lashing ring DIEB Release handle folding mechanism Adjustable footrest 9 Rear lashing ring 5 Removable seat with lateral supports Kimba neo Ottobock 5 Introduction gt Ns Kimba neo outdoor mobility base with multifunctional seating unit and swiveling front wheels option Plug on rear wheel I _ 6 Adjustable push bar Swiveling front wheel option Release handle folding mechanism Swivel lock a Separate
36. s 4 Tighten the mounting screws see Fig 30 Pos 1 3 Kimba neo Ottobock 15 Service Work 3 5 5 Frame 3 5 5 1 Replacing the Front Frame re Ol 6 y CO co Remove the plug on rear wheel Put the frame on its side Remove the caster wheels swivelling front wheels see Fig 33 item 1 fixed front wheels see Fig 35 Loosen the mounting screws between the rear wheel linkages and lower front frame see Fig 33 item 2 see Fig 35 item 2 Using a spiral bit 5 mm bore out 8 rivets between the lower upper front frame see Fig 33 item 3 see Fig 35 item 3 Tap out the rivets with a pin punch 3 mm Remove and replace the front frame Front frame for swivelling front wheels see Fig 34 Front frame for fixed front wheels see Fig 36 Rivet install the front frame with the mounting materials provided Tighten the mounting screws between the rear wheel linkages and lower front frame see Fig 33 item 2 see Fig 35 item 2 Install the caster wheels see Page 10 ff 16 Ottobock Kimba neo Service Work INFORMATION The front frame is offered complete see Fig 37 and alternatively in a version without seat adapter Remove the plug on rear wheel Put the frame on its side Remove the caster wheels swivelling front wheels see Fig 39 item 1 fixed front wheels not illustrated Loosen the mounting screws on the suspension see Fig 24
37. t block for shortening the lower leg length 38 Ottobock Kimba neo Appendices 4 Appendices 4 1 Technical Data Dimensions cm and weights kg Outdoor mobility base Suei Se Overall width so NN Front wheel diameter swiveling front wheels Front wheel diameter fixed front wheels Rear wheel NN E Seat tilt seating B angle ya 35 10 or 10 35 35 10 or 10 35 Min folded size with seat facing forwards seat tilted 90x60x539 97x67x59 backwards 10 back angle 100 LxWxH Multifunctional seating unit EDEN BEE Seat depth 19 31 24 40 with seat cal reducer option possible from 14 cm Mas Ind enpnch a jo Max load capacity for use in a wheelchair accessible 40 Venice Wegh 88 Folded size with lateral padding LxWxH 58x37x42 59x43x58 1 The outdoor mobility base with fixed front wheels in size 2 is available only as a custom fabrication 2 The load capacity differs between the outdoor mobility base and the seating unit e Seating unit max 40 kg own weight of the seating unit size 1 7 5 kg 47 5 kg e Outdoor mobility base max 55 kg fully loaded seating unit 47 5 kg 7 5 kg for other accessories weight in storage basket 9 Folded dimensions of the outdoor mobility base with fixed front wheels 97x60x53 cm 4 Observe the information in the section Use in a Wheelchair Accessible Vehicle Kimba neo Ottobock 39 Appendices 4 2 Maintenance Schedule
38. th proper alignment see Page 24 Preinstall the supports on the correct sides with the mounting materials provided see Fig 109 Put the mounting screws through the slotted holes in the support and the slotted holes in the back frame back insert respectively see Fig 110 Pos 1 Fasten the thoracic supports on the back of the back insert using knurled nuts If necessary adjust the width height Hand tighten the knurled nuts 10 Fold the backrest pad back over the supports and close the zipper 3 6 5 3 Replacing the Hip Supports 1 Remove the seat pad see Fig 70 Kimba neo Ottobock 35 Service Work og 9 Remove the covers from the supports see Page 24 Loosen the 4 x knurled nuts on the underside of the seat see Fig 103 Pos 1 Remove the mounting screws and supports Preinstall the supports on the correct sides with the mounting materials provided see Fig 112 Put the mounting screws through the slotted holes in the support and the slotted holes in the base frame seat frame and the front seat plate respectively see Fig 113 Mount the hip supports on the underside of the seat using knurled nuts see Fig 103 Pos 1 Adjust the seat width by moving the hip supports see Fig 113 This also allows for abducted settings Hand tighten the knurled nuts Adjust the depth of the supports if reguired see Fig 114 Tighten the mounting screws 10 Pull the covers over the supports
39. the Storage Basket NOTICE Incorrect attachment Damage to the product gt During the attachment make sure that the product cannot grind against the wheels 1 Open the snap fasteners and hook and loop straps of the storage basket see Fig 51 Pos 1 see Fig 52 Pos 1 2 Remove and replace the storage basket 3 Mount the storage basket with the proper side to the frame using the snap fasteners and hook and loop straps see Fig 51 Pos 1 see Fig 52 Pos 1 20 Ottobock Kimba neo Service Work 3 5 7 2 Replacing Retrofitting the Tip Assist 1 Install the tip assist on the lashing point at the rear with 2 mounting screws see Fig 53 item 1 2 Firmly tighten the cap nuts see Fig 54 item 1 Ne CNN EE CIERRE A AIM BDA Ie p ul y RNIN 5 B Ama SL E Be SAD Useina wheelchair accessible vehicle is forbidden Severe injury in case of accidents gt Use of the product in wheelchair accessible vehicles in combination with the artificial respiration platform option Is not permitted INFORMATION The respiration platform cannot be used on a product with fixed front wheels Mounting instructions e The option can be installed as follows Installation of the large plate over the front wheels see Fig 55 user sits in the seat facing opposite to the direction of travel Installation of the large plate over the rear wheels see Fig 56 user sits in the seat facing in the direction o
40. ts Remove the covers from the supports see Page 24 and replace the supports Pull the covers over the new supports with proper alignment see Page 24 Preinstall the supports on the correct sides with the mounting materials provided see Fig 107 INFORMATION With a microfibre pad the supports first have to be threaded through the slits in the backrest pad Put the mounting screws through the slotted hole in the support and the bore hole in the back insert respect ively see Fig 108 INFORMATION If the headrest supports are to be mounted to the top holes mounting points of the back plate the longer mounting screws which come with the device will have to be used instead of the regular mounting screws Fasten the headrest supports on the back of the back plate using the knurled nuts see Fig 106 Adjust the width in the slotted holes if required Hand tighten the knurled nuts 10 With a standard pad Fold the backrest pad back over the supports and close the zipper With a microfibre pad Close the zipper 34 Ottobock Kimba neo Service Work 3 6 5 2 Replacing the Thoracic Supports S22 NE 9 Open the zipper at the top of the pad see Fig 70 and fold the backrest pad forward Loosen the knurled nuts on the back of the back plate no illustration Remove the mounting screws and supports Remove the covers from the supports see Page 24 and replace the supports Pull the covers over the new supports wi
41. two bearing bushings to the seat depth reducers see Fig 92 item 2 see Fig 93 item 2 INFORMATION In doing so secure the mounting screws with a medium strength liquid thread lock compound see Fig 94 6 Attach the hip pads and pull over the covers Removing the seat depth reducer 1 Remove the covers 2 Remove the hip pads see Page 35 3 Loosen and remove the four mounting screws on each seat depth reducer see Fig 92 item 1 2 Remove the bearing bushings The back frame is now separated from the base frame 4 Attach the back frame with the bearing bushings inserted see Fig 90 item 3 to the base frame see Fig 95 item 1 using two mounting screws see Fig 90 item 1 2 5 Attach the hip pads and pull over the covers 30 Ottobock Kimba neo Service Work 3 6 3 Footplate Knee Angle Assembly 3 6 3 1 Replacing the Foot Plate 1 Recommendation Set the knee angle assembly horizontal 2 Loosen the mounting screws in the slides see Fig 96 Ensure that the inserted flange nuts see Fig 97 Pos 2 do not fall out of the slides in the process 3 Remove the footplate from the footplate adapter see Fig 96 Pos 2 and replace it 4 Slide the footplate onto the footplate adapter 5 Tighten the mounting screws in the sliders to a torque of 5 Nm 3 6 3 2 Replacing Small Parts on the Footplate Replacing the Sliders 1 Remove the footplate 2 Loosen the mounting screws on the sliders see
42. with proper alignment see Page 24 11 Replace the seat pad and secure it with the hook and loop fastener see Fig 70 3 6 5 4 Replacing the Lateral Supports ba Ol Open the zipper at the top of the pad see Fig 70 and remove the backrest pad see Page 24 Remove the covers from the supports see Page 24 Remove the back insert see Page 26 Remove and set aside the back frame see Page 29 Remove the back plate from the back frame Using a spiral bit 9 5 mm bore out 4 rivets between the back frame and back plate see Fig 115 Pos 1 and tap them out with a pin punch 3 mm Remove the 4 x Phillips screws between the back frame and back plate see Fig 115 Pos 2 Remove the 2 x set screws from the tube clamp see Fig 116 Pos 1 Remove the knob see Fig 85 Pos 1 and the mounting screw see Fig 85 Pos 2 from the clamp tie bar see Fig 85 Pos 3 Pull the back plate off the back frame Pull the tubes of the back frame see Fig 116 Pos 2 from the lateral pads see Fig 116 Pos 3 and the plastic slides of the clamp tie bar see Fig 116 Pos 4 Replace the lateral supports see Fig 118 Ottobock Kimba neo Service Work 8 Push the tubes of the back frame see Fig 116 Pos 2 through the lateral supports see Fig 116 Pos 3 and the plastic slides of the clamp tie bar see Fig 116 Pos 4 on the back plate 9 Rivet and screw the back plate in place
Download Pdf Manuals
Related Search