j-45718 icc target board
Contents
1. string with the centerline of the vehicle to the ground Ew see Figure 3 TP020467 Figure 3 6 Attach the Laser Pointer to the Slider Assembly f Slider Assembly Level Indicator e Asshown in Figure 4 the Target Board is removed from the Slider Assembly when the Laser Pointer is attached Laser Pointer NOTE The Laser Pointer mounting is off set depending on the vehicle you re working on It could be up down or to the side left right See Figures 4 and 4a e Table A on page 4 for vehicle off set application Revised New Off l set Block Adapter e change the off set remove the mounting 7 TP090385 screw and rotate the block adapter Figure 4 3 16 ITB02 059c e poston All Hex Screws QX4 JR50 E i QX56 JA60 17 mm Q45 F50 M45 Y34 17 mm M35 45 Y50 28 mm EX35 J50 G35 G37 Sedan V36 G37 Coupe CV36 FX35 45 S50 0mm FX35 50 851 Table A The block adapter is mounted horizontally Figure 4a with the hex screw shown in Figure 4 7 Now you ll need to align the Target Board Support Base to the vehicle as follows a Lookatthe chart on page 5 to determine where the string should be aligned Target Board Aon ett Support Base scale in correct location NOTE The support base has an alignment As shown string is scale on both sides driver and passenger aligned at 10 inches i 254 mm f Figure 5 s2. 511910 6 3 8 16 Cap Screw 10057 T Washer 10258 8 3 8 16 Hex Nut 10204 10 Plastic Clip 513202 11 10 24x 5 Socket HD Screw 11434 12 10 24x 63 Socket HD Screw 11152 13 10 24 Nut 10197 14 Bead Chain 513201 16 O Ring 10265 17 10 24x 38 Socket HD Screw 14276 18 Clamp Knob 511916 19 Bullseye Level 511979 Not Background Board J 45718 6 Shown SPX Corporation 655 Eisenhower Drive Owatonna MN 55060 0995 Phone 800 662 2001 Fax 586 578 7375 513817 Phone 1 800 662 2001 FAX 1 586 578 7375 faa TP020482 12 16 ITB02 059c MATERIAL SAFETY DATA SHEET Revised 1 June 2004 SECTION 1 PRODUCT IDENTIFICATION EMERGENCY INFORMATION MANUFACTURER S NAME UNITIKA LTD ADDRESS T 541 8566 4 1 3 KYUTARO MACH CHUOU KU OSAKA JAPAN PHONE NO FOR INFORMATION 81 6 6281 5354 EMERGENCY PHONE NO 81 774 25 2335 CHEMICAL NAME Polyethyleneterephthalate Glass Fiber TRADE NAME UNITIKA UNILATE PC CHEMICAL FAMILY MIXTURE OF POLYESTER COMPONENTS MATERIAL CAS NUMBER X POLYESTER 25038 59 9 lt 70 GLASS FIBER 65997 17 3 gt 30 SECTION 2 HAZARDOUS INGREDIENTS PC CONTAINS NO HAZARDOUS INGREDIENTS SECTION 3 PHYSICAL DATA BOILING POINT F VAPOR PRESSURE mm Hg VAPOR DENSITY AI R 1 SOLUBILITY IN WATER APPEARANCE AND ODOR SPECIFIC GRAVITY 0 1 VOLATILE BY EVAPORATION RATE SECTION 4 FIRE AND EXPLOS
3. QY INFINITI SERVICE BULLETIN COPYRIGHT NISSAN NORTH AMERICA INC Classification Reference Date 02 025 ITB02 059c July 28 2009 ESSENTIAL TOOL J 45718 ICC TARGET BOARD This bulletin amendment contains additional Applied Vehicles information for modifying the Target Board and a revised tool Please discard all previous versions of this bulletin APPLIED VEHICLES 2002 2003 JR50 with optional ICC 2003 2004 M45 Y34 with optional ICC 2006 2009 M35 45 Y50 with optional ICC 2002 2006 Q45 F50 with optional ICC 2003 2008 FX35 45 850 with optional ICC 2009 FX35 50 851 with optional ICC 2004 2009 QX56 JA60 with optional ICC 2007 2009 G35 G37 Sedan V36 with optional ICC 2008 2009 G37 Coupe CV36 with optional ICC 2008 2009 EX35 J50 with optional ICC SERVICE INFORMATION When performing Laser Beam Aiming Adjustment for the Intelligent Cruise Control ICC system a special tool must be used e This special tool is the Target Board J 45718 e This special tool is considered Essential and has been sent to each dealer Your Non Vehicle account was charged 600 00 plus applicable taxes and freight e A revised new Offset Laser Block Adapter J 45718 10 replaces J 45718 5 was sent on July 27 2009 to your dealership Your Non Vehicle account will be charged 27 43 plus applicable taxes and freight e Additional tools and or replac
4. Inc J 45718 ICC System Target Board Application Q45 QX4 M45 Note This special service tool is required to adjust aim the laser beam on the Intelligent Cruise Control System The laser beam must be adjusted every time the ICC sensor is removed or installed on the noted vehicles The special black and white target board materials have a specific reflective rate needed for the laser sensor The stand includes a built in bulls eye level laser pointer protractor and scale for faster and easier set up A flat black backdrop is included to elimi nate reflections from nearby objects The backdrop can also be used to protect the target board while in storage between uses Please reference TB02 059 in ASIST for information on ICC Target Board use This essential tool will be invoiced to your Infiniti non vehicle account at 600 00 plus appropriate taxes and freight in accordance with your dealer agreement with Nissan North America Inc Promotion IF02 532A KENT MOORE SPX Corporation 655 Eisenhower Drive Owatonna MN 55060 0995 Phone 800 662 2001 Fax 986 578 7375 Phone 1 800 662 2001 FAX 1 586 578 7375 TPO20481 11 16 ITB02 059c EPIS Description Order 1 Support Base J 45718 1 2 Slider Assembly J 45718 2 3 Board Assembly J 45718 3 4 Vertical Support J 45718 4 9 Laser J 45718 5 15 Block Adapter revised J 45718 10 5
5. inches NOTE Target boards or complete tools purchased after March 23 2004 will already be the smaller size and won t need to be cut If you re not sure measure your board The new size is 630 mm 24 8 inches high e The MSDS for the Target board is attached at the end of this TSB pages 11 and 12 14 Set up the Background Board behind the Target Board see Figure 13 e he Background Board prevents reflection from Board objects such as workbenches walls or other A vehicles t least 15 Board must extend at least Vehicle and Target Board set up is complete 15 inches beyond gt _ the Target Board 15 Perform Laser Beam Aiming Adjustment Procedure e Use CONSULT II IIl as applicable Sting Tagel gt e Refer to the appropriate section of the ESM Pd TP020474 Figure 13 WARNING Do Not look straight into the ICC sensor laser beam discharge when performing Laser Beam Aiming Adjustment with CONSULT 9 16 ITB02 059c When the Target Board is not in use stored wrap the Background Board around the Target Board and use the Velcro straps to hold it in place see Figure 14 Velcro straps Sf 3 E TP020475 Figure 14 10 16 ITB02 059c mm TO Dealer Principal and Dealer Service Manager 2002 Infiniti EG 332 02 09 The following service tool has been classified essential by Nissan North America
6. ION HAZARD DATA FLASH POINT gt 460 C FLAMMABLE LIMIT EXTINGUISH MEDIA ORDINARY MEDIA SUCH AS WATER AND ETC SPECIAL FIRE AND EXPLOSION HAZARDS USE SUPPLIED BREATHING AIR AND PROCTIVE CLOTHING UNUSUAL FIRE AND EXPLOSION HAZARDS AVOID DISPERSION OF DUST IN AIR TO REDUCE EXPLOSION POTENTIAL SECTION 5 HEALTH HAZARD DATA PC ARE NOT HAZARDOUS MATERIAL 50105 13 16 ITB02 059c SECTION 6 REACTIVITY DATA STABILITY NONE INCOMPATIBILITY MATERIALS TO AVOID NOTHING HAZARDOUS CONBUSTION OR BURNING CAN PRODUCE CO CO DECOMPOSITION PRODUCTS AND OTHER PRODUCT OF UNDETERMINED COMPOSITION AND TOXICITY HAZARDOUS POLYMERIZATION WILL NOT OCCUR AT ROOM TEMPERATURE SECTION 7 SPILL OR LEAK PROCEDURES STEPS TO BE TAKEN IN CASE SWEEP COLLECT IN SUITABLE CONTAINER MATERIAL 15 RELEASED OR FOR DISPOSAL SPILLED CAUTION PELLETS ON FLOORS ARE SLIPPERY AND CAN CAUSE FALLS WASTE DISPOSAL METHOD INCINERATE OR BURY IN A LANDFILL IN ACCORDANCE WITH APPROPRIATE FEDERAL STATE AND LOCAL REGULATIONS SECTION 8 SPECIAL PROTECTION INFORMATION RESPIRATORY PROTECTION NOTHING REQUIRED IN NORMAL USE PROTECTIVE GLOVES SUBSTANTIAL LEATHER WORK GLOVES EYE PROTECTION SAFETY GLASSES VENTILATION GENERAL ROOM VENTILATION SHOULD BE ADEQUATE SECTION 9 SPECIAL PRECAUTIONS PRECAUTIONS TO BE TAKEN IN HANDLING STORING AVOID BREATHING DUSTS FOR INDU
7. STRY ONLY OTHER PRECAUTIONS CONVEYING LINES AND EQUIPMENT IN MATERIAL HANDLING SYSTEMS SHOULD BE GROUNDED TO ELIMINATE OR REDUCE BUILDUP OF STATIC ELECTRICITY AVOID SOURCES OF IGNITION AS IN ANY AREA WHERE DUST MAY BE PRODUCED TP050106 14 16 ITB02 059c lzcm M eas ESSENTIAL NISSAN AUTHORIZED TOOL amp EQUIPMENT PROGRAM TOOL SHIPMENT TO Dealer Principal Dealer Service Manager 2009 Infiniti The following special service tool has been classified essential by Nissan North America Inc J 45718 10 ICC Aiming Target Block Adapter amp Job Aid Application Infiniti vehicles with the Intelligent Cruise Control Option Note The J 45718 10 block adapter replaces the current small block adapter Refer to included instructions for installation procedure There is a laminated job aid ICC TARGET BOARD SETUP amp USAGE included in this shipment Refer to ITB02 059 for detailed information on the complete service procedure Laser pointer attaches here This tool will be invoiced to your Non Vehicle Account at 27 43 plus applicable taxes and freight in accordance with your dealer agreement with Nissan North America Inc See Opposite Side TP090636 Phone 1 800 662 2001 FAX 1 586 578 7375 19 16 ITB02 059c Installation Instructions for J 45718 10 Refer to Drawing 1 below Unscrew the Laser pointer Item 9 the block adapter Remove the 10 24 Socket HD Screw Item 12 from the block ad
8. Up 1 Prepare the vehicle for Laser Beam Aiming Adjustment Place the vehicle on a flat level surface Make sure you leave a minimum of 18 feet 5 5 meters of space in front of the vehicle Check adjust tire pressure to the specified pressure for the vehicle being serviced Make sure there is no load in the vehicle other than the driver or equivalent weight placed in the driver s position Coolant and engine oil must be filled up to the correct level and the fuel tank must be full shift the gear selector into P position and release the parking brake Clean the ICC sensor with a soft cloth 2 16 ITB02 059c Target Board Set Up 2 First you ll need a length of string about 30 feet 9 meters long 3 Tape one end of the string to the ground at the center point of the rear of the vehicle see Figure 2 NOTE The Infiniti emblem can be used to align the center point see Figure 2 cani point EE Tape string to ground at N center point a TP020466 Figure 2 4 Now extend the string under the vehicle and out S M A the front r e f e Pull it out about 18 feet 5 5 meters in front of I d 0 the vehicle see Figure 3 FYI CD E 9 Pullthe string straight and align it with the centerline T av of the vehicle front then tape the string to the to align string with SERM ground see Figure 3 centerline of vehicle Lea 5 5 meters NOTE You can use the Infiniti emblem to align the
9. apter Discard the old adapter Item 15 Install new J 45718 10 block adapter Attach laser pointer to the new block adapter UI NN o Note The laser pointing device is attached with a chain to the slider assembly Figure 1 4 Description Order 1 Support Base J 45718 1 2 Slider Assembly J 45718 2 3 ICC Target Board J 45718 3 Remove socket head cap 4 Vertical Post 549099 screw and replace Item 15 T 5 Knob 511910 6 3 8 16 Cap Screw 10057 7 Washer 10258 8 3 8 16Hex Nut 10204 9 Laser Kit J 45718 5 10 Plastic Clip 513202 o 11 10 24x 5 Socket HD Screw 11434 S yj 12 10 24x 63 Socket HD Screw 11152 13 10 24 Nut 10197 14 Bead Chain 513201 15 Block Adapter revised 552842 16 O Ring 10265 17 10 24 38 Socket HD Screw 14276 x 18 Knob 511916 19 Bullseye Level 511979 o Not LDW LDP Target Board J 49192 1 T shown g D Not Background Board J 45718 6 Shown 20 Job Aid 554230 Complete Kit Part Number J 45718 A Promotion IF09 213 KENT MOORE SPX SERVICE SOLUTIONS 655 EISENHOWER DR OWATONNA MN 55060 0995 AN SPX BRAND PHONE 800 662 2001 FAX 586 578 7375 TP090637 16 16 ITB02 059c
10. ement parts can be ordered from TECH MATE at 1 800 662 2001 Prices are subject to change e The Tool Flyer and Parts Replacement List that were shipped with the tool are included in this bulletin on pages 11 and 12 e The Target Board illustrations in the ACS Auto Cruise Control System and CCS Cruise Control system sections of the Electronic Service Manual ESM as it applies do not show several improvements that were applied to the tool during development These improvements allow for easier and faster set up e The Target Board material has special reflective properties Other materials should not be used 1 16 Support Base Slider Assembly Target Board Vertical Support Height Adjustment Knob 3 8 16 Cap Screw Washer 3 8 16 Hex Nut Laser Pointer Plastic Clip 10 24x 5 Socket HD Screw 10 24x 63 Socket HD Screw 10 24 Nut Bead Chain Block Adapter revised O Ring 10 24x 35 Socket HD Screw T Handle Bullseye Level Indicator 1 2 3 4 6 L 8 g TP020500 Figure 1 When performing the Laser Beam Aiming Adjustment use the Target Board Set Up Instructions in this bulletin Also follow the steps for CONSULT II III operation as applicable in the appropriate section of the Electronic Service Manual ESM WARNING Do Not look straight into the ICC sensor laser beam discharge when performing Laser Beam Aiming Adjustment with CONSULT SET UP PROCEDURES Vehicle Set
11. ghten the strike ICC sensor knob e t may be necessary to slightly rotate the TP020472b support Base left or right to horizontally aim the Pointer Beam in the correct position Figure 9 NOTE Normally Left and Right is determined when sitting in the driver seat For this procedure only Left and Right will be determined when standing in front of and looking at the front of the vehicle Center Line Right Side Weide Example JR50 JR50 Q45 F50 M45 Y34 Example A Center Line 2006 2007 M Y50 B J 2008 2009 M Y50 C 2003 2008 FX35 45 950 A 2009 Fx35 50 S61 C e 92 mm 3 62 in lt gt 0 EX35 J50 22 mm 0 87 in Table D 22 mm 0 87 in Example C NOTE Measure from the edges of the laser lens itself not the fascia around it n 1 5 in WARNING The Pointer Beam emits laser radiation Avoid direct eye exposure Do not look directly into the Pointer Beam 7 16 ITB02 059c 12 Remove the Laser Pointer with the off set block adapter still attached from the Slider Assembly see Figure 10 mount with NOTE At this point do not move the Target specified degree mark Board Base on stand e fthe Target Board Base is bumped or moved its alignment procedure starting 47 at Step 7 will need to be performed again Figure 10 13 Install the Target Board see Figure 10 Deg
12. hows the driver side Front of vehicle 254 mm for QX4 String Figure 5 TP020469 4 16 ITB02 059c b Setthe legs of the Target Board Support Base into alignment parallel with the string Lookat Table B below and make note of Alignment measurement for the vehicle you re working on d Move the base left or right and align the string to the correct reading on the scale or to the center e Make sure the legs of the Target Board Support Base are always parallel to the string 10 inches 254 mm as shown in Figure 5 10 8 inches 275 mm 35 637 Sedan V36 Passenger 15 91 inches 404 mm G37 Coupe CV36 9 72 inches 247 mm for Sport series bumper EX35 J50 10 12 inches 257 mm Table B Driver side of Center support of Target Board Targer Board Base Base NOTE For vehicles requiring string alignment at the center as indicated in the chart above align string as shown in Figure A Front of vehicle String aligned at center of Target Board Base t TP020469c Figure A 5 16 ITB02 059c 8 Now you ll set the distance from the front of the Laser Pointer to the front most edge of the vehicle front bumper e Put the height of the Laser Pointer about S equal to that of the ICC Sensor s before NN Pac from the front bumper to measuring the front of the Laser Pointer e Use Table C below to determine the Use chart A4 distance to be measured determine your vehicle s di
13. rees Setting Q45 F50 M45 Y34 2003 2008 FX35 45 S50 20 e Setalignment mark at degree setting as stated in Table E QX56 JA60 QX4 JR50 2006 2007 M Y50 2008 2009 M Y50 2009 FX35 50 S51 NOTE The face of the Target Board G35 G37 Sedan V36 25 when angled should be facing toward G37 Coupe CV36 the center of the vehicle EX35 50 Figure 11 shows an example for a Target Table E Board located on the driver side of the Vehicle Center line e Hand tighten the T handle Target Board Vehicle Center Face Line XXXX in Figure 11 8 16 ITB02 059c IMPORTANT Follow the procedure below if your Target Board s height is not already at the Final Height measurement e Due to the lower position of the ICC sensor on the E iam 2006 M and 2005 Q45 the Target Board will need after cut to be modified for use on these vehicles 630 mm 24 8 in e his modification is also recommended when using this tool on 2003 2004 M45 It will make it easier to Pu install the board in the correct position Cut 70 mm 2 75 in e This modification will not affect the use of the board off of the bottom on other vehicles e Cut 70 mm 2 75 in off of the bottom of the Target Board e Score the white reflective tape with a razor knife and then use a suitable handsaw to make the cut TP050093 Figure 12 e The final height after cut of the board should be 630 mm 24 8
14. stance Vehicle Distance 5 Q45 F50 Laser Pointer M45 Y34 FX35 5 S50 QX66 JA600 QXA JRE M35 50 Y51 FX85 45 S50 12 8 feet 3 9 m G37 Coupe CV36 EX35 J50 16 4 feet 5 m Turn level adjustment knobs until the bubble in the level indicator is centered Table C C A _ NOTE While moving the Support Base to this A Level distance make sure the string stays correctly indicator aligned Center TIP There is a T handle used for Target Board adjustment mounting Store the T handle in the opening at the top of the Vertical Support when not in use see Figure 6 TP020471 Figure 7 9 Now you ll need to level the Target Board oupport Base see Figure 7 e Bring the bubble into the center of the level indicator To do this turn the knobs on the oupport Base legs NOTE If the work surface under the support base Is slightly uneven use the center adjustment for additional leveling 10 Turn the Laser Pointer ON The switch is at its base see Figure 8 Figure 8 6 16 ITB02 059c 11 Adjust the Pointer Beam up or down so it strikes the ICC sensor see Figure 9 e For Laser Pointer Beam on sensor lens target location refer to Table D below to determine which ICC sensor Example to use as a guide e Loosen the height adjustment knob Md Adjust pointer beam to e Once Pointer Beam is adjusted ti
Download Pdf Manuals
Related Search