Professional - Andi
Contents
1. from C to 2 Place the saucepan onto the Zone 2 hobplate until the display flashes repeatedly from to 3 Repeat for Zones 3 4 and 5 as the display indicates This procedure registers the hob zones If the zones are registered correctly all five displays will flash Fig 10 The hob is now configured If the zone is registered incorrectly the five display will flash 4 m m Correctly 5 5 configured 5 Not configured Note If the hob has failed to register then switch the appliance off for a few seconds to clear the memory and repeat the above procedure 8 Circuit Diagrams Circuit Diagram Hob ToT1 To T2 To T4 To T5 To Earth MCB MCB MCB MCB MCB br br br bl b b gy b b br b br b b br p yee gy CU2 Jor oy S CUB r br b iF Dy b 2 3kW 2 3kW 2 3kW r b r b 1 4kW 1 4kW B Touchlite panel Colour Code Blue Distribution board Brown Left hand front control Black Left hand rear control Orange Red Central control Right hand rear control Violet Right hand front control White Yellow Green yellow Grey 34 Circuit Diagram Conventional Oven Key The connections shown in the circuit diagram are for single phase The ratings are for 240 V 50 Hz Descriptio2. CLASSIC Professional toledo 110 Induction U110101 01sm INSTALLATION Check the appliance is electrically safe when you have finished N28 O OOS A N 1 phase 240 V 50 Hz New plate Cover extension WS SS b Electrical Connection This appliance must be installed by a qualified electrician to comply with the relevant regulations AS NZS 60335 2 6 2002 and also the local electricity supply company requirements Ensure that the mains characteristics voltage nominal power etc match the ratings indicated on the data plate affixed to the cooker The cooker is preset for a single phase earthed electrical connection It is essential to install a multi pole circuit breaker that completely disconnects the appliance from the mains with a minimum contact break distance of 3 mm Current Operated Earth Leakage Breakers The combined use of your induction cooker and other domestic appliances may cause nuisance tripping so we recommend that the cooker is protected on an individual RCD Residual Current Device or RCBO Residual Current Breaker with Overload IF IN DOUBT PLEASE CONSULT A SUITABLY QUALIFIED ELECTRICIAN A WARNING THIS APPLIANCE MUST BE EARTHED The appliance must be connected to an efficient earthing circuit If the electricity network is not equipped with an earth connection then it must be installed separately in compliance with local regulations Earth
3. and UI Board Release Rotray Control Replace Rotary Control Replace Link Wire Flash Error Micro Defective Exchange UI Board Display of Residual Heat Cooling of Hob Required Overheating of Connection Units Basic Induction Codes Pot Glass too high a temeprature NTC Electronic too high Cooling of the Power Board Required Ne DISpiay Diet Volaghom swith Blind Connection with 400 V Check Voltage Supply hiii mmode power supply No Failure Unqualified Pot HW Failure IHE not configured or NO communication between IHE and the UI Board No Failure User is in the Service Menu Mode Pot is creating an incorrect working point on power board This may destroy some of the components on the board 1 IHE not Configured 2 More than 1 IHE has the same configuration 3 IHE is not connected to not enabling the Power to the IHE Complete the Configuration Process This Error Code will be relplaced after 8 S and the unit can be used again If the error code reappears the pot has to be removed and replaced 1 amp 2 Configure the IHE unit using the service menu or the IR diode 3 Check the Power supply and also the connection between the Power Board and the supply voltage or Filter Board is Connection Unit CU 4 If none of the above clears the fault replace the IHE unit SSS Error on Filter Board Filter Board Defective Exchange Filter Board CU Etroron Power Board e on Powe
4. away from the rear of the cooker Fit the new fan and reassemble in reverse order Check the operation of the oven 21 To Change Oven Light Bulb Disconnect from electricity supply Make sure the oven is cool Open the oven door and remove the oven shelves Remove the grill pan and support from the grill chamber Unscrew the bulb cover by turning anti clockwise It may be very stiff Fig 8 14 Taking care to protect your fingers in case the bulb should shatter unscrew the old bulb Fit an Edison screw fitting 15 W 240 V lamp FOR OVENS It must be a special bulb heat resistant to 300 C Fig 8 15 Screw in the new bulb and then screw back the bulb cover Turn on the electricity supply and check that the bulb now lights 33 RANGEIMastecr Remove grommet from LH amp RH Side panels Fixing screw is located inside Rear fixing screw left amp right Following removal of the 4 fixing screws induction glass top can raised RANGETNaster k Filter board A controls Zone 1 amp 2 CU1 Filter board B controls Zone 5 CU2 Filter board C controls Zone 3 amp 4 CU3 br ay seas Tore an aie esn 300 140 81 co gt r YGP043938 RANGEMaster SS YGP043940 YGP045291 Page 1 of 1 General Error Codes Error of Input unit Rotary Control Permanent Operation of Rotary Control or Broken Wire between Rotary Control
5. ck appliance is safe when you have finished 8 Servicing A Disconnect the cooker from the electricity supply before servicing particularly before removing any of the following control panel side panels ceramic hob or any of the electrical components or cover boxes A Before reconnection check that the appliance is electrically safe 1 To Remove a Side Panel Disconnect from electricity supply Pull the cooker forward Pull off the control panel end caps at each end of the panel Fig 8 1 Remove the fixing screws under the end caps Remove the retaining screws for each panel one at the front two at the rear and one at each lower front corner of the side panels Reassemble in reverse order 2 To Lift up the Ceramic Hob Disconnect from electricity supply Pull off the push fit control panel end caps at each end and remove the end fixing screws under the end cap Remove the lower front retaining screws one each side situated beneath the lower edge at the front corners of the side panels Swing the side panels to gain access to the hob fixing screws 1 each side at the top front of the side uprights Remove these screws Lift up the ceramic hob at the front and prop into position with a non metallic prop CAUTION The ceramic hob material is much more sensitive to scratches on the underside than the top Take care not to touch or scratch the underside of the ceramic as this will weaken the mater
6. d be above the fixings Remove the 4 mm Allen screws from the top corners of the fascia Fig 7 14 Fit the front handrail in position and secure using the 4 mm screws Fig 7 14 27 INSTALLATION Check the appliance is electrically safe when you have finished Fitting the Plinth Classic amp Professional models Loosen the three screws along the front bottom edge of the cooker Hook the central keyhole over the central screw Twist and fit each end keyhole over their respective screws Tighten the fixing screws Fig 7 15 Fig 7 15 Toledo model Fit the inner plinth to the bottom front of the cooker using the 5 screws provided Fig 7 16 Fit the outer plinth 2 screws 1 each end to the inner plinth The height of the outer plinth can be adjusted by sliding it up or down via the slotted hole Fig 7 17 Fitting the Splashback classic model only The cooker can be installed with or without the supplied splashback Position the splashback on the rear of the hotplate and secure with the screws supplied Fig 7 18 Fig 7 17 Customer Care Installer Please complete your details in this Guide inform the user how to operate the cooker and hand oven the instructions Thank you Outer plinth Outer plinth fixing screw Inner plinth Fig 7 18 28 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity before servicing Che
7. der Check for correct operation To Remove Grill Element Disconnect from electricity supply Remove the grill pan from the grill compartment Undo the two screws and washers in the grill roof and remove the enamelled front shield Undo the 2 screws and washers securing the grill element front support Remove the screws from the grill elements Lift the elements out carefully and noting their position disconnect the leads from the element terminals 30 10 11 12 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity before servicing Check appliance is safe when you have finished If it is not possible to disconnect the leads in this way pull the cooker forward to gain access to the rear Undo the screws securing the electric cover to the back sheet and remove the cover Disconnect the terminals from the rear Fit new elements and reassemble in the reverse order Check the operation of the grill To Remove the Grill Door Remove the left hand side panel see 1 Remove the control panel see 3 Remove the centre cover strip 5 screws 2 top 2 bottom 1 in middle Remove the two countersunk screws 1 each side securing the grill hinge arms to the front of the grill chamber Note The arms are spring tensioned Carefully remove the grill door Retain the gaskets Reassemble in reverse order ensuring that the gasket is fitted between the hinge arm and the front
8. der making sure that the four screws and washers are fully tightened To Replace a Thermostat Disconnect from the electricity supply Lift the ceramic hob and remove the control panel see 2 amp 3 Open the oven door Remove the oven furniture For the right hand oven remove the thermostat phial cover two screws Unclip the thermostat phial from the clips in the oven back For the left hand oven pull cooker forward to gain access to the cover box at the rear of the cooker Remove the four screws securing the cover and lift clear Feed the thermostat capillary out of the oven Disconnect the wiring from the thermostat Remove two screws holding thermostat to mounting panel Fit new thermostat and reassemble in reverse order Ensure that the phial is clipped to the oven back with the phial centrally positioned between the clips Check the operation of the thermostat To Remove an Oven Element Thermal Cut out Disconnect from electricity supply Pull the cooker forward to gain access to the cover box Undo the cover screws and lift clear The cut out is located on the earth plate beside the oven element connections Disconnect the cut out wiring Undo the fixings that secure the cut out to the earth plate and remove Fit the replacement control and re assemble in reverse order 32 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity before servicing Check appliance is safe
9. ial and cause the top to shatter 3 To Remove the Control Panel Classic only Remove the handrail by unscrewing the 2 end bracket fixing screws Fig 8 2 Pull off the control panel end caps at each end of the panel Fig 8 1 Remove the fixing screws under the end caps Pull off all the control knobs Open the grill and right hand oven door and remove the control panel fixing screws underneath the control panel The screws directly below the clock are for the clock fixing bracket so do not remove them at this stage Lift the control panel pull forward and disconnect the wiring from the rear Reassemble in reverse order When replacing leads refer to the wiring diagram in this manual Check the operation of the timer 29 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity before servicing Check appliance is safe when you have finished To Replace a Hob Element Disconnect from electricity supply Lift up the ceramic hob see 2 The Induction Heating Elements IHE are now accessible Note the wire connection positions and element orientation for re assembly Disconnect the 4 wires and remove the element unit and the 3 springs Fit the new sealing ring around the fan vent Fig 8 3 and refit the 3 springs Re assemble in the reverse order Note The IHE will require commissioning when the hob has been refitted To Replace the Light Switch Disconnect from electricit
10. ing is a safety measure required by law and must be performed with particular care by a qualified technician who must also check that the electricity supply characteristics are correct The total electrical load of the appliance is approximately 17 1 kW The cable size used should be suitable for this load and comply with all local requirements i e PVC Insulated cable IEC 60227 code 53 for ordinary cables Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel Connect the mains cable to the correct terminals for your electrical supply type Fig 7 6 and Fig 7 7 Check that the links are correctly fitted and that the terminal screws are tight Secure the mains cable using the cable clamp Fixed Wiring For connection to fixed wiring i e flexible conduit remove the electrical terminal cover box on the back panel Undo the two screws and remove the blanking plate from the bottom flange of the cover box Replace it with the new plate and then fit the cover box extension Fig 7 8 Fix the conduit bracket to the centre upright Fig 7 9 Fit the conduit up to the bracket and secure in place with the plastic nut 26 INSTALLATION Check the appliance is electrically safe when you have finished Connect the mains cable to the correct terminals for your electrical supply type Fig 7 10 and Fig 7 11 Check that the Fig 7 10 links are correctly fitted and that the terminal screws a
11. l load at 240V 16 8 kW approximate total including oven lights oven fan etc 36
12. n Description Colour Code Right hand oven thermostat Clock Blue Right hand oven thermostat front switch Grill energy regulator Brown Right hand oven element Grill elements Black Right hand oven fan Grill front switch Orange Left hand zoned oven thermostat Cooling fan Red Left hand zoned oven thermostat front Oven light switch Violet switch Oven light White Zoned oven browning element inner pair Thermal cut out Yellow Zoned oven top element outer pair Neon Green yellow Zoned oven base element Grey 35 10 Technical Data INSTALLER Please leave these instructions with the User DATA BADGE LOCATION Cooker back serial number repeater badge below oven door opening Connections Dimensions Overall height minimum 902 mm maximum 927 mm Overall width 1100 mm Overall depth 602 mm to fascia inc splashback 610 mm over hotplate Refer to Positioning the Cooker Ratings 2 3kW 2 3kW 2 3kW 1 4kW 1 4kW Conventional Forced air convection Browning element 1 15 kW Energy efficiency class on a scale of A more efficient to G less efficient Energy consumption based on standard load 0 99 kWh 0 85 kWh Usable volume litres 67 67 A A Size Large Large Time to cook standard load 40 minutes 38 minutes Surface area of the grid 1400 cm 1400 cm Maximum total electrica
13. of the grill chamber Remove the two screws and washers securing the grill element front support Remove the screws from the grill element Lift the element out carefully disconnecting the leads from the element terminals noting their position If it is not possible to disconnect the leads in this way pull the cooker forward to gain access to the rear remove the screws securing the electric cover to the back sheet remove the cover and disconnect the terminals from the rear Fit the new element and reassemble in reverse order Check the operation of the grill To Replace an Oven Door Open the oven door Support the door and remove the two screws securing the upper hinge and gasket to the cooker front Fig 8 4 Remove the door from the lower hinge by lifting slightly and moving outwards Fig 8 5 A The door is heavy so take care Reassemble in reverse order To Adjust an Oven Door Angle The bottom hinge of either oven door can be adjusted to alter the angle of the door Fig 8 6 Loosen the bottom hinge fixing screws and use the notch and a flat bladed screwdriver to move the position of the hinge to set the hinge position Fig 8 7 Retighten the hinge screws To Replace an Oven Door Outer Panel Move the cooker forward to gain access to the sides Open the oven door slightly and remove the front panel fixing screws from the door sides two each side Fig 8 8 Carefully lift off the outer door panel Remove the do
14. or handle from the panel by unscrewing the two retaining nuts Fit the door handle to the new panel Fit the panel to the door Reassemble in reverse order Effect of hinge adjustment exagerrated for clarity Centreline of hinge pin 31 WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity before servicing Check appliance is safe when you have finished Fig 8 10 13 14 15 16 17 To Change an Oven Door Latch Remove the outer door panel see 12 Remove screws B that hold the latch assembly to the inner door panel Fig 8 9 Fit the new catch and reassemble in reverse order Verify the door operation To Adjust an Oven Door Catch Keep Open the oven door and slacken off the locknut at the base of the keep Fig 8 10 Screw in or out as required until the required fit is obtained Retighten the locking nut To Replace an Oven Door Seal Open the oven door The seal has small hooks that hold it in place by locating into holes in the rear door face on the main oven and oven front face on tall oven At the corner pull the seal diagonally away from the door centre until the hook is released Fig 8 11 Proceed to the next hook and release it in a similar way and so on You can use force if the hooks are stiff as the old seal will be discarded Carefully lift away the inner back Reassemble in reverse or
15. r Board Power Board Defective Board Defective Exchange Power Board IHE Open Circuit Short Circuit Thermal Sensor defective or Change Temperature value of coil sensor not plugged in Senor Coil Sensor Induction Heating Element IHE Configuration Procedure Zone 1 control Zone 2 control IMPORTANT The configuration process must be completed within two minutes of turning on power to the The display will cooker flash between C and 1 Turn the front left zone 1 control anticlockwise to A and hold in position Fig 2 3 Rotate the front left Zone 1 control clockwise to position 9 Fig 5 the display will show a flashing Fig 6 2 Turn the rear left zone 2 control clockwise to Position 9 Flick the control knob clockwise beyond position 9 three times Fig 3 The display will show E 7 The display will now flash alternately between C and 7 Fig 4 F200012 01 Leave the control knob in position 9 until the display stops flashing then return the control knob anticlockwise to 0 The display will once again flash alternately between and 7 Fig 7 The display will flash between C and 1 4 Take a ferrous saucepan it must be magnetic and place it on the Zone 1 hobplate Fig 8 and Fig 9 The display will now alternate between and 2 T The display will flash alternately
16. re tight Replace the electric terminal cover box make sure that the conduit is clear of the bottom flange Repositioning the Cooker following Connection If you need to move the cooker once it has been connected make sure it is switched off at the supply switch before gripping under the fascia panel and lifting the front of the cooker slightly Fig 7 5 Check behind the cooker to ensure that the electricity cable is not caught As you progress always ensure that the cable has sufficient slack to allow the AEAN Fig 7 11 cooker to move al ANAM AJ 889 AEAN S S I rmi LOIS FS Ra eo Fos re 3 phase 240 415 V 50Hz A Make sure to release the stability chain as you ease the cooker out Do not forget to refit it when you replace the cooker When you replace the cooker check behind it again once more to ensure that the electricity cable is not caught or Fixing bracket for trapped conduit connection Hob Check Check each cooking zone in turn Be sure to use pans of the correct size and material Grill Check Conduit Turn on the grill control and check that the grill heats up Oven Check Set the clock as described earlier and then turn on the ovens Check the oven fans start to turn and that the ovens heat up Fitting the Handles and Handrail classic model only Remove the 4 mm Allen screws from the doors Fig 7 12 Fit the door handles and secure using the 4 mm screws Fig 7 13 A The handles shoul
17. when you have finished 18 To Remove an Oven Inner Back Disconnect from electricity supply Open the door and remove the shelves Remove the screws and washers securing the inner back to the back of the oven Fig 8 12 Carefully lift away the inner back Reassemble in reverse order making sure that the screws and washers are fully tightened 19 To Remove the Fan Oven Element Disconnect from electricity supply Remove the oven inner back see 18 Remove the two screws from the top of the element and the one from the bottom of the element inside the oven Fig 8 13 Lift the element out carefully disconnecting the terminals connected to the element noting their positions If it is not possible to disconnect the leads in this way pull the cooker forward to gain access to the rear Remove the screws securing the electric cover to the back sheet remove the cover and disconnect the terminals from Element fixing screws the rear 20 To Replace an Oven Fan Disconnect from electricity supply Pull the cooker forward to gain access to the rear Remove the screws securing the electric cover to the back sheet and remove the cover Disconnect the three terminals connected to the fan noting their position Remove the oven inner back see 20 Hold the fan blade and remove the centre nut left hand thread two brass washers fan blade and circlip Unscrew the fan retaining nuts and washers three off each and lift the fan
18. y supply Remove the control panel see 3 Note The old switch may be destroyed during removal Remove the old switch from its bezel by gripping the switch body behind the control panel and twisting sharply Remove the switch bezel by folding back its locking wings and pushing forward Fit the new bezel to the control panel by first lining up the raised key on its body with the cut out in the control panel and pushing it in from the front Assemble the new switch to the bezel by lining up the key sections and pushing home Fit the new button by pushing in from the front Replace the Control Panel in reverse order and test for correct operation To Remove the Electronic Timer Disconnect from electricity supply Remove the control panel see 3 Pull off the timer control button s Remove the timer mounting bracket assembly from the control panel by removing the fixing screws Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case at the same time pulling the unit forward Reassemble in reverse order When replacing the leads refer to the wiring diagram in this manual Check the operation of the timer To Replace the Grill Controller Disconnect from electricity supply Lift up the hob and remove the control panel see 2 and 3 Disconnect the wiring from the controller Remove the two screws holding the controller to the mounting panel Fit the new controller and reassemble in reverse or
Download Pdf Manuals
Related Search