GReddy Intercooler Kit
Contents
1. 2 aluminum 50 Right Side 1 4 l 3 aluminum 50 Left Side 1 5 a l 4 aluminum 50 Left Side 1 6 Y 1 5 aluminum elbow 70 no 9 1 ve i l 6 aluminum 702 1 8 Rubber Hose 100 550mm 1 9 Silicone Hose 702 Straight 2 10 i 502 602 Reducer 2 11 Hose Band 102 Tridon 5 6 12 502 Tridon 32 2 13 602 Tridon 36 2 14 702 Tridon 44 4 15 Straight Tube S 2 16 4 102 2 17 Power Steering Cooler 1 18 Power Steering Cooler Bracket 1 Set 19 Washer Tank 1 20 Washer Tank Relocation Bracket 1 Set 21 Washer Tank Extension Hose B 1500mm 2 22 Washer Tank Exhtension Harness 1 Set 23 Aluminum Spacer 1 24 M6 x 15mm Stainless P 1 00 B SW F W N 2 25 M6 x 25mm Stainless P 1 00 B SW F W 1 26 M8 x 15mm Stainless P 1 25 B SW F W 1 1 Parts List 22 23 24 26 2 Stock Parts Removal Please refer to the factory service manual for the proper stock parts removal 2 1 Disconnect the negative terminal of the battery 2 2 Remove the under engine cover 2 3 Remove the front bumper 2 4 Remove the bumper reinforcement 2 5 Remove the left and the right side horn 2 6 Remove the Power steering fluid cooler 2 6 Remove the charge pipe C 2 C 3 and C 5 from the turbo kit 3 Kit Installation 1 Core Installation Mount the intercooler core as shown Secure the top bracket to the hood latch assembly and the bottom bracket to the sub frame Parts Used 1 24 26 2 Intake Pipe Installation 1 Install the Int2. While idling check for any oil coolant or air leeks 6 After inspection reinstall the under cover and other stock parts that was removed 7 After inspection reinstall the under cover and other stock parts that was removed 8 On the initial run be sure to have a boost gauge to check the turbo actuator setting This turbo kit is preset to boost between 0 6kg cm to 0 5kg cm It is very important that you monitor the boost pressure and make sure not to over boost Over boosting can cause engine damage This completes the Intercooler Kit installation
3. GReddy Intercooler Kit 2003 Nissan 350Z VQ35DE Front mount Type 23 2003 Nissan 350Z VQ35DE Front Mount Type 23 Installation Manual Please read the entire manual before installing this kit Application Make Model Chassis Year Nissan 350Z Z33 2003 e This GReddy Intercooler Kit is designed only for the vehicles specified above with GReddy Turbo Kit part 11520093 installed e Premium grade gasoline 91 octane or higher is required with this Kit e Make sure that the vehicle is not equipped with any ECU upgrade chips e Use of GReddy Racing Spark Plugs ISO 7 LONG or NGK plugs colder than factory is recommended with this kit Important This installation should only be performed by a trained specialist who is very familiar with the automobile s mechanical and electrical system If installed by an untrained person it may cause damage to the kit as well as the vehicle GReddy Performance Products Inc is not responsible for any damage to the vehicle s electrical system caused by improper installation Call your GReddy Authorized dealer or GReddy Performance Products if there are any problems or questions regarding this product Installation of this kit will require the removal of the front bumper support beam If you are uncomfortable with the removal please stop the installation 1 Parts List 1 Intercooler Type23 1 2 Intake Pipe l 1 aluminum 50 Right Side 1 3
4. ake pipe 1 1 and l 2 from C 1 pipe from the turbo kit to the top intercooler in let as shown 2 Install the Intake pipe l 3 and l 4 from C 4 pipe from the turbo kit to the bottom intercooler in let as shown 3 Install the Intake pipe l 5 and 1 6 from intercooler outlet to the airflow meter as shown Parts Used 2 3 4 5 6 7 9 10 12 13 14 Right side turbo 1 2 to the intercooler Intercooler to the airflow meter 3 Power Steering Fluid Cooler Installation Install the power steering fluid cooler as shown Parts Used 8 11 16 17 18 3 Horn and Air Bag sensor relocation Relocate the horn and the sir bag sensor using the provided brackets as shown Parts Used 22 23 25 4 Washer tank Installation 1 Remove the washer pump from the factory washer tank and reinstall them to the provided tank 2 Mount the washer tank using provided brackets as shown 3 Connect the hoses and the wires using the provided extension harness and hoses Parts Used 15 19 20 21 22 5 Front Bumper Modification Trim the grill off and all the area that would contact the intercooler core 6 Starting the Engine 1 Refill the coolant and the power steering fluid to factory spec 2 Check all the hoses and wires connection then reconnect the negative side of the battery 3 Start the engine 4 Turn the steering wheel all the way left and all the way right Fill the power steering fluid if necessary 5
Download Pdf Manuals
Related Search