INSTRUCTIONS - Harley
Contents
1. HARLEY DAVIDSON J02245 INSTRUCTIONS REV 7 12 01 Kit Number 69172 01 STROBE KIT PAR 36 FOR FLHP AND FXDP POLICE MODELS General This Strobe Kit Par 36 is designed for installation on 2000 and later FLHP I FLHTPI and 2002 FXDP Model Motorcycles when equipped with H D Police Tour Pak See Service Parts Page Illustration for kit contents WARNING The rider s safety depends on the correct installation of this kit If the following installation procedures are not within your capabilities or if you do not have the correct tools have your Harley Davidson dealer perform this installation Failure to do the installation correctly could result in death or serious injury NOTE A Service Manual for your vehicle is available from your Harley Davidson dealer Installation To protect against shock and accidental start up of vehicle disconnect the negative battery cable before proceeding Inadequate safety precautions could result in death or serious injury Always disconnect the negative battery cable first If the positive cable should contact ground with the negative cable installed the resulting sparks may cause a battery explosion which could result in death or serious injury 1 Disconnect battery cables negative battery cable first N Follow instructions in applicable Service Manual and remove fuel tank 9 Remove the two socket head screws securing the left side directional signal to t2. 6 strobe 1 will be used 18 Route the left and right Strobe Harnesses under the fuel tank then toward the back of the bike taking the same path as the left and right directional lamp conduits Continue along the frame and back into the opening in the Tour Pak 19 Obtain the three wire ties 6 from kit and secure the strobe harness to the frame or directional lamp conduit at appropriate locations Repeat for the other harness 20 See Figure 4 Connect the strobe harness connectors to the power supply as shown NOTE Depending on which of the four outlets are chosen the flash pattern can be set so lamps flash alternately or simultaneously You may want to experiment with the various outlets until the desired flash pattern is achieved 21 Obtain the Power Supply Control Harness 7 and instructions from kit Follow the instructions supplied with the harness and install harness Connect control harness to power supply 22 Follow instructions in applicable Service Manual and install fuel tank J02245 Recessed Area Directional Signal Assembly Figure 3 Reinstall Directional Signal to Passing Pursuit Lamp Mounting Bracket Strobe Harnesses or Power Supply Control Harness Figure 4 Connect Strobes to Power Supply Outlets Always connect the positive battery cable first If the positive cable should contact ground with the negative cable installed the resulting sparks may cause a battery explosion whi
3. ch could result in death or serious injury 23 Install battery cables positive cable first 24 Close Tour Pak and test strobe lights for proper operation 2 of 3 Part Nos 69172 01 Date 7 01 CANY e Service Parts Par 36 Strobe Kit for Police Models i03981 Description Qty Part Number Strobe par 36 blue 68554 01 Strobe par 36 red 68542 01 Harness par 36 strobe 2 70670 01 Connector AMP socket 3 wire 2 70289 89 Terminal pin socket AMP 6 72038 71A Ties wire large 6 10006 Kit harness power supply control See Note NOTE Refer to Instruction Sheet J02192 provided with Power Supply Control Harness Part Number 70669 01 supplied in this kit J02245 3 0f 3
4. he Spotlamp Mounting Bracket Save screws for reinstallation A Remove the Phillips screw at at the bottom of the lamp molding and remove the chrome ring from the lamp bucket Save screw for reinsallation Carefully pull the sealed lamp unit out and away from the bucket p Disconnect the wire terminals from the sealed beam unit gt See Figure 1 Locate the spotlight power wire and cleanly cut the terminal end off of wire The spotlight power wire will vary in color according to the left and right lamps and the model Note the following FLHTP I and FLHP I Models Power Wire for Left and Right Lamps Grey Black FXDP Models Left Lamp Power Wire Grey Violet Right Lamp Power Wire Grey Brown 7 Push pull the wire down through the spotlamp mount post and cut the wire at the entrance to the conduit Tape the end and tuck the wire into conduit NOTE Tuck the ground black wire with terminal into the lamp bucket so it is out of the way Back Into Figure 1 Modify Existing Wiring 8 See Service Parts Illustration Obtain one of the Strobe Harnesses 3 from kit and locate the open end 3 wires no connector 9 Begin inside the Tour Pak and push the open end of the harness through the right side straight fitting at bottom of Tour Pak Route harness along frame under fuel tank and along existing directional lamp conduit up to front 10 See Figure 2 Route Push the 3 wires from harness up through the lamp m
5. ounting stem and out into the lamp bucket following the same route as when removing the original power wire J 1 of 3 11 See Service Parts Illustration Obtain three Socket Pin Terminals 5 and one plastic 3 place Connector 4 from kit 12 Follow instructions in Service Manual under Installing Amp Connectors and install a socket terminal to each of the wire ends 13 Note the numbers marked on the plastic connector and install each of the terminals into the following respective cavity Make sure the socket terminals snap into place Red Wire Terminal to Connector Cavity 1 Black Wire Terminal to Connector Cavity 2 White Wire Terminal to Connector Cavity 3 NOTE When performing the following Step the Red Par 36 Strobe is normally installed on the left side the Blue Par 36 Strobe is installed on the right side 14 See Service Parts Illustration Obtain the left Par 36 Strobe Lamp Red 2 from kit and mate the harness connector with the strobe connector 15 Position the Strobe within the mount and reinstall the chrome ring using the Phillips head screw removed in Step 4 Tighten securely 16 See Figure 3 Make sure conduit rests in the recess of the clamp area as shown Reinstall the left directional signal assembly to the Spotlamp mounting bracket using socket head screws removed in Step 3 Tighten screws securely 17 Perform Steps 3 through 16 for the right side of the motorcycle The Blue Par 3
Download Pdf Manuals
Related Search