SpectraLux Rear ILS Lightbar
Contents
1. e After installation and testing are complete provide a copy of these instructions to instructional staff and all operating personnel e File these instructions in a safe place and refer to them when maintaining and or re installing the product Failure to follow all safety precautions and instructions may result in property damage serious injury or death RETAIN AND REFER TO THIS MESSAGE Introduction The Rear SpectraLux ILS is a single level LED lightbar that mounts in the rear window of the vehicle It uses ROC Reliable On Board Circuitry technology and SoLARis S2 reflectors The lightbar operates at a nominal input of 13 6 Vdc 11 Vdc minimum The functions of the ILS are controlled through the CATS serial communication cable The cable connects to either a compatible Federal Signal Serial control head or a Federal Signal Serial Interface Module document P N 8583446 An internal PCB assembly within the lightbar decodes the control data and performs the requested function With the Serial Interface Module the lightbar can be activated by Federal Signal lightbar controllers SignalMaster M controllers and or individual low current switches The backbone is a powder coated aluminum shroud The lightbar has 15 ft power and ground cables and a 25 ft serial cable Mounting hardware is a configured option Refer to mounting instructions supplied with mounting hardware The lightbar has an operating temperature range of 30 C2. ILS DX HEAD s SNALMAs ri CONTROL BOARD e 290A7042 Safety Message to Operators of Warning Light Equipment People s lives depend on your safe use of our products Listed below are some important safety instructions and precautions you should follow e Do not attempt to activate or de activate the light system control while driving in a hazardous situation e Although your warning system is operating properly it may not be completely effective People may not see or heed your warning signal You must recognize this fact and continue driving cautiously e Also situations may occur which obstruct your warning signal when natural and man made objects are between your vehicle and others such as raising your hood or trunk lid If these situations occur be especially careful e The effectiveness of an interior mounted warning light depends on the clarity the tinting and the angle of the glass it 1s being placed behind Tinting dirt defects and steeply angled glass reduce the light output of the warning light This may reduce the effectiveness of the light as a warning signal If your vehicle has dirty tinted or steeply angled glass use extra caution when driving your vehicle or blocking the right of way with your vehicle e All effective sirens and horns produce loud sounds that may cause in certain situations permanent hearing loss You and your passengers should consider taking appropriate safety precautions suc
3. at a close range Do not stare directly into this lighting product at a close range or permanent damage to your eyesight may occur Do not install the light system in an area that would block impair or blind the driver s vision Ensure that the light system 1s mounted in a position that 1s outside of the driver s field of vision so the driver can safely operate the vehicle Federal Signal power supplies and light heads are designed to work together as a system Combining light heads and a power supply from different manufacturers may reduce the warning effectiveness of the lighting system and may damage the components You should verify or test your combination to ensure the system works together and meets federal state and local standards or guidelines Electrical Hazards Strobe systems present a shock hazard because they use high voltage to operate Do not handle strobe cables the power supply or bulbs or remove the lens while the equipment is connected Strobe systems can also hold their charge even after they have been turned off After disconnecting power to the unit wait five minutes before handling any parts of the strobe system A light system is a high current system In order for the system to function properly a separate negative connection and positive connection must be made All negative connections should be connected to the negative battery terminal and a suitable fuse should be installed on the positive batt
4. flatness and thickness of the steel mounting surface Therefore to promote proper magnetic mounting v Mounting surface and magnets must be kept clean dry and free of foreign particles that prevent good surface contact Ensure that mounting surface is flat A magnet mounting system should not be used on vehicles with vinyl tops To prevent sliding of light assembly on mounting surface quick acceleration and hard stops should be avoided Failure to follow these precautions may result in property damage serious injury or death RETAIN AND REFER TO THIS MESSAGE Testing the Lightbar A WARNING LIGHT HAZARD This product contains high output LED devices To prevent permanent eye damage do not stare into the light beam at close range To check the lightbar controls see Table 1 on page 9 and the wiring diagrams on pages 18 and 19 1 3 Connect the 16 AWG black lead from the lightbar to the ground NEG terminal of the vehicle battery and the 16 AWG red lead to the positive terminal Connect the black and black white wires from the Serial Interface Module to the ground NEG terminal of the vehicle battery Apply 12 Vdc to a control wire and to the ignition wire from the Serial Interface Module After the installation check the entire system to be sure the lights are flashing properly and all light system functions are operating properly Maintaining the Rear ILS Establishing a regular maintenance schedule f
5. 3 outer PCB straight out before lifting it Remove the outer PCB by sliding it straight outward and then lif ng it by its outside edge To remove an inner PCB make sure all the nuts have been removed Disconnect the cable and lift out the PCB SpectraLux Rear ILS Lightbar i 14 Installation Maintenance and Service Manual NOTE To remove a reflector see Replacing a Reflector on page 16 4 To install an inner PCB align the holes in the PCB with the three inner studs on the shroud and place the PCB on the insulator 5 Mate the pins of the outer PCB to the inner PCB on an angle 6 Slide the outer PCB in while lowering its outer edge until the stud is centered in the slot on the PCB Rest the PCB on the insulator 7 Tighten the 10 32 nuts to 36 in Ib 3 ft lb Figure 2 Removing a PCB INSULATOR 1 FOR EACH PCB CABLE LENGTH IS VEHICLE SPECIFIC REMOVE THE 710 32 HEX NUTS FROM THE STUDS 1 FOR EACH OUTER PCB 3 FOR EACH INNER PCB e SLIDE THE OUTER PCB OUTWARD LIFT THE OUTER EDGE OF THE PCB AND REMOVE THE PCB DISCONNECT THE CABLE c amp eq LIFT OUT THE INNER PCB 290A7043 SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual Replacing a Reflector A WARNING CRAZING CHEMICAL S Crazed cracked or faded reflectors reduce the light output and the effectiveness of the lighting system Reflectors showing this type of aging must be replaced Failure
6. FEDERAL SIGNAL Protecting people and our planet x Rear ILS Lightbar Installation Maintenance and Service Manual 25500022 REV A1 0214 Printed in U S A blank page Installation Maintenance and Service Manual Table of Contents Safety Message to Installers and Service Personnel of Warning Light Equipment 5 PYRE O CUCU ON eec ME 7 Unpacking THe IES emi amtsi sees sentln esuert tate wre ster Bente sree ees ote ent 8 ov ech re etter meres esr ee tees e eee steer eewn eters sm ot 7 Wiring the Rear ILS in the Vehicle cir a aa a a 7 SE EE 0 EE 8 ee 8 Typical Installations with Common Control Systems rere nennen enne nenne 9 belectinb C OMMOUTAL OM le EE 9 Safety Message to Operators of Warning Light Equipment eee ee eeeeeee eee 11 Testing Me EE ee 12 Maintaining The Rear VES crm 12 Glenin the SAT OUGS wi aia eo nota 13 C canc ee dC HeC O eege 13 SETVICNO NE Rear IES ED TEE P MOULIN RISE 13 Replacing EE 13 FRG AGA RSC COE m E E A M 15 Ordering Replaceinent EE 16 List of Tables Table 1 Rear ILS lightbar controls and their wires from the Serial Interface Module 9 Table 2 Rear ILS DIP switch Settllids roo eeE ENEE EES EE EE 10 Table 3 Common replacement parts 16 REEL ee DaS EE 16 List of Figures Figure 1 DIP switches and lights on the control board of the Rear IL 11 Figure 2 Removing
7. GPC EE 14 Figure 3 Removing a Tellee Ol EE 15 Figure 4 Typical connections with a SignalMaster controller external Control 17 Figure 5 Typical connections with a SmartSiren Model GGS2000M esee 18 Figure 6 Typical connections with a serial controlled lightbar and externally controlled SpectraLux Rear ILS 19 SpectraLux Rear ILS Lightbar ARJENT LEGEND RAYDIAN SMARTSIREN and SOLARIS are registered trademarks of Federal Signal Corporation SIGNALMASTER SpectraLux and ROC are trademarks of Federal Signal Corporation SpectraLux Installation Maintenance and Service Manual Safety Message to Installers and Service Personnel of Warning Light Equipment People s lives depend on your proper installation and servicing of Federal Signal products It is important to read and follow all instructions shipped with this product In addition listed below are some other important safety instructions and precautions you should follow Before Installation or Service Qualifications To properly install or service this equipment you must have a good understanding of automotive mechanical and electrical procedures and systems along with proficiency in the installation and service of safety warning equipment Always refer to the vehicle s service manuals when performing equipment installations on a vehicle Light Hazards To be an effective warning device this product produces bright light that can be hazardous to your eyesight when viewed
8. JSN V L NOILIN I Jjsnadvsi Jsfna v Gh AH3LIVS e J lt JJ Smg oF ee ALC oz 28280 52 DR D20024 EE EE oQuoouz XY z S 222221 SNOILONYLSNI 391430 H3d eu t ee SNOLLO3NNOO SNINIVIA3H O OO OO OO P GO NM eee Nd er E Z INSO00cSS Je iei ib lei eee SNMOQ3MV LI X18 LHM OONON SLAdLNO XNV ERE SLHSIT t 3a3OW Mg z SGOW LHWN19 e 3don aau xia SNMOQ3MVI HSY14 419 dSy NSOOOZSS 9po N ueJigueuug e UI suonoeuuoo jeoidAL S e1nDi J SpectraLux Rear ILS Lightbar 18 Installation Maintenance and Service Manual E G0Z V067 14 SII dvaa XNWYLOAdS S1VO qaad ds v St ASN v Op SNMOQ3MV L HSV14 M18 a3H qauP ria IHN fYIS X 18 NH9 aV Hl OHIO X18 LHM GOW z 3GOW Ola kg OOOO ecb KON T NOLLINSI XO8 SNOILONYLSNI SOIAAG H3d SNOILO3NNOO SNINIVIA3H XO HOLIMS aa3u xia LHM 3OVJH3LNI TVIH3S asnav lt 2 33OW LHAW N1g IAOW LHM dsnavt KRIS 3OVJ3H2ANI 1VIH3S AdilLIVg O I Z ive r A gt T O J dh O D 2 O H SNOILONYLSNI 39144A H3d SNOILOSNNOO SNINIVIA3H H3TIOHLNOO H31SVNWTIVNDIS S IVNSIS ONT WOH SACIAO d HJTIOHLNOO H31SVWIVNDIS io AOVAYALNI 1VIH3S OL CH 1eeH xn TeJioedgs pejjouuoo Ajeu14e81xe pue IEOIUDU pejogiuoo eues e y y m suonoeuuoo eoid 9 eunBiJ 19 SpectraLux Rear ILS Lightbar FEDERAL SIGNAL Protectin
9. White Red Cycles through each available color SW 2 Switch 3 in the Serial Interface Module is in the UP position See document P N 2562248 for instructions on setting these options in the Serial Interface Module Typical Installations with Common Control Systems For typical installations with common control systems see Figures 4 through 6 starting on page 17 Selecting Configuration Options The Rear ILS has three configuration options that are selectable with DIP switches on the lightbar control board Table 2 on page 10 describes the options SpectraLux Rear ILS Lightbar 10 Installation Maintenance and Service Manual Table 2 Rear ILS DIP switch settings DIP Switch Description Position 1 Sets the directional arrow pattern for internal SignalMaster control for the eight default or six head pattern For the six head pattern move DIP Switch 1 to ON Figure 1 on page 11 Switch 3 has three functions Activating a lower or upper rear mounted ILS Performing an LED scan to ensure that an LED board flashes the correct colors after it is installed Changing the Device ID to enable the SpectraLux ILS to operate independently of the lightbar available with the Convergence Configuration Software Choosing to Activate an Upper or Lower Rear ILS To activate a upper rear mounted ILS set Switch 3 ON To activate a lower rear mounted ILS set Switch 3 OFF Performing an LED Scan When an LED board is ch
10. anged an LED scan must be done to enable the LED board to flash the correct colors To perform the scan Disconnect the red power BAT wire to the SpectraLux ILS and maintain power to the control head interface box Change the position of DIP Switch 3 and turn power ON to the SpectraLux ILS The SpectraLux ILS emits a short flash to indicate the LED scan is done To return DIP Switch 3 to its original function repeat the scan Changing the Device ID The default setting for the SpectraLux ILS is to respond to lightbar commands For example if the system includes a lightbar and a SpectraLux ILS both devices perform the same func tions The Convergence Configuration programming software enables you to program the control head to send a set of commands dedicated only to the SpectraLux ILS making its operation independent of the lightbar To reset the control head to the default setting perform an LED scan as described above oets the ability to power the network cable for other devices The default is OFF Switch 4 should only be set if the main power cables are turned on through an ignition activated relay If powering other devices such as the Six Button Serial Controller set DIP Switch 4 to ON For more information see the instructions included with the network powered device SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual Figure 1 DIP switches and lights on the control board of the Rear
11. ery terminal connection as close to the battery as possible Ensure that all wires and fuses are rated correctly to handle the device and system amperage requirements Never attempt to install aftermarket equipment that connects to the vehicle wiring without reviewing a vehicle wiring diagram available from the vehicle manufacturer Ensure that your installation will not affect vehicle operation or mandated safety functions or circuits Always check the vehicle for proper operation after installation The lighting system components especially light bulbs strobe tubes LEDs and the outer housing get hot during operation Be sure to disconnect power to the system and allow the system to cool down before handling any components of the system Do not mount a radio antenna within 18 inches 45 7 cm of the lighting system Placing the antenna too close to the lighting system could cause the lighting system to malfunction or be damaged by strong radio fields Mounting the antenna too close to the lighting system may also cause the radio noise SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual emitted from the lighting system to interfere with the reception of the radio transmitter and reduce radio reception Do not attempt to wash any unsealed electrical device while it is connected to its power source During Installation and Service DO NOT get metal shavings inside the product Metal shavings in the product ca
12. g people and our planet 2645 Federal Signal Drive University Park IL 60484 3167 Tel 800 264 3578 708 534 3400 Fax 800 682 8022 www fedsig com 2014 Federal Signal Corporation
13. h as wearing hearing protection e In order to be an effective warning device this product produces bright light that can be hazardous to your eyesight when viewed at a close range Do not stare directly into this lighting product at a close range or permanent damage to your eyesight may occur e It is important that you fully understand how to safely operate this warning system before use e You should only operate your vehicle and its light sound system in accordance with your department s Standard Operating Procedures e Ifa selected function does not perform properly or if any of the lamps remain illuminated when the control is off disconnect the power connector from the control unit and contact the nearest service center e Atthe start of your shift you should ensure that the entire warning light system and the siren system is securely attached and operating properly SpectraLux Rear ILS Lightbar 12 Installation Maintenance and Service Manual Suction cup mounting is for temporary applications only The unit should be removed from the window and stored securely when not in use Temperature changes and sunlight can cause suction cups to lose holding power Periodically check the unit to be sure the suction cups have a firm grip on the mounting surface An improperly secured light could fall off of the vehicle causing injury and damage The holding power of magnetic mounting systems is dependent upon surface finish surface
14. hicle with a magnetically mounted warning light installed The light could fly off the vehicle causing injury or damage Repair of damage incurred because of ignoring this warning shall be the sole responsibility of the user To avoid denting the roof of the vehicle place the lightbar mounting feet as close to the outer edge of the roof as possible Locate the light system controls so the VEHICLE and CONTROLS can be operated safely under all driving conditions After Installation or Service After installation test the light system to ensure that it 1s operating properly Test all vehicle functions including horn operation vehicle safety functions and vehicle light systems to ensure proper operation Ensure that the installation has not affected the vehicle operation or changed any vehicle safety function or circuit Scratched or dull reflectors mirrors or lenses will reduce the effectiveness of the lighting system Avoid heavy pressure and use of caustic or petroleum based products when cleaning the lighting system Replace any optical components that may have been scratched or crazed during system installation SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual e Do not attempt to activate or de activate the light system control while driving in a hazardous situation e You should frequently inspect the light system to ensure that it is operating properly and that it is securely attached to the vehicle
15. llow this warning can damage the reflectors and reduce the effectiveness of the light output which may result in bodily injury or death to you or others To clean the reflectors L To remove the lightbar from the vehicle refer to the vehicle specific installation instructions included with the Rear ILS Use a soft tissue to clean the reflectors If needed you can use a solution of mild soap and water but take care to avoid getting the PCBs wet Avoid heavy pressure and the use of caustic abrasive or petroleum based cleaners which will scratch or dull the reflectors When finished make sure the lightbar is completely dry before reinstalling it according to the vehicle specific instructions Servicing the Rear ILS This section has instructions for replacing the lightbar s PCBs and reflectors For additional service and support call the Federal Signal Service Department at 800 433 9132 7 a m to 5 p m Monday through Friday Central Time For a list of common replacement parts see Ordering Replacement Parts on page 17 Replacing a PCB To replace a PCB 1 2 To remove the lightbar from the vehicle refer to the vehicle specific installation instructions that come with the Rear ILS NOTE To remove an inner PCB you must first remove the outer PCB next to it See Figure 2 on page 15 Remove the 710 32 nuts that hold down the PCB E NOTICE PCB CONNECTOR DAMAGE To avoid damaging the connectors slide the
16. n and vehicle specific replacement parts To order parts call the Federal Signal Service Department at 800 433 9132 7 a m to 5 p m Monday through Friday CT or contact your nearest distributor Table 3 Common replacement parts PCB Assembly Passenger Side Configured Table 4 Vehicle specific parts Part Number Wire Assembly PCB to PCB Vehicle Specific Length 17500009 Shroud and Mounting Hardware Vehicle Specific Refer to the vehicle specific installation instructions for part numbers SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual ZF0ZV06c S1I Hvau xn ivaloads qaad dsfnua v GL AH3LIVS EE fal Q z JINON 3OV3H3LNI 1VIH3S OL oO coz STIVNDIS ONTIOHE saaiAoud ko cus LESLSZL N d OSA H3TIOHLNOO HALSVWIVNDIS J0 GO BOX m Hallds We 520020 T 2000 020 Dy Iz 002 lc ONG SNMOQ3 V L HSV 13 414 034 X 18 1LHM NOILINSI T cL Jjsnaviti e 330 aau xia z 33OW LHWN19 t 3don n8 NMOQ3MV AOVAYALNI IWIYAS XO8 SNOILONYLSNI 39IA3Q H3d echt SNOLLO3NNOO SNINIVIA3H XO HOLIMS AAE O1 UOD euJo81X9 19 041u09 J81se A euDiS YIM suonoeuuoo eoid pain SNOILONYLSNI 39IA3Q Yad SNOILOANNOO ONINIVIN3H H3TIOHINOO H31SVWTVNDSIS 17 SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual 9r0ZVO06c LESLSZL N d DSA d3ll 1dS AOVAYALNI Igic LHM S1 Hvau XNWELOAdS
17. n cause the system to fail If drilling must be done near the unit place an ESD approved cover over the unit Inspect the unit after mounting to be sure there are no shavings present in or near the unit DO NOT connect this system to the vehicle battery until ALL other electrical connections are made mounting of all components is complete and you have verified that no shorts exist If the wiring is shorted to the vehicle body or frame high current conductors can cause hazardous sparks resulting in electrical fires or flying molten metal DO NOT install equipment or route wiring or the plug in cord in the deployment path of an airbag Before mounting any components check the manual to be sure that the component you are installing is suitable for use in that area of the vehicle Many components are not suitable for use in the engine compartment or other extreme environmental exposure areas When drilling into a vehicle structure be sure that both sides of the surface are clear of anything that could be damaged Remove all burrs from drilled holes To prevent electrical shorts grommet all drilled holes through which wiring passes Also ensure that the mounting screws do not cause electrical or mechanical damage to the vehicle Refer to the manual packed with the lighting system for proper electrical connections additional precautions and information Because vehicle roof construction and driving conditions vary do not drive a ve
18. or the ILS lightbar extends its life and ensures safety Periodically check that the lightbar operates properly and that all mounting hardware is securely fastened to the vehicle Also inspect the reflectors for cracks crazing hairline cracks discoloration and other defects AWARNING PERIODICALLY CHECK GLASS The effectiveness of the Rear ILS depends on the clarity of the glass it is being placed behind Dirt and defects in the glass reduces the light output The reliability of light for emergency signaling purposes may be reduced if the glass is dirty cracked or not clear Be sure to periodically check the glass for cleanliness to ensure maximum light output of the Hear ILS lightbar SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual Cleaning the Shrouds To clean the shrouds 1 To remove the lightbar from the vehicle refer to the vehicle specific installation instructions that come with the ILS lightbar Use a soft tissue to clean the shroud If needed you can use a solution of mild soap and water but take care not to get water on the PCBs When finished make sure the lightbar 1s completely dry before reinstalling it according the vehicle specific installation instructions Cleaning the Reflectors AWARNING CRAZING CLEANING SOLUTIONS The use of cleaning solutions such as strong detergents solvents and petroleum products can cause crazing cracking of the reflectors Failure to fo
19. tenna too close to the lighting system could cause the lighting system to malfunction or be damaged by strong radio fields Mounting the antenna too close to the lighting system may also cause the radio noise emitted from the lighting system to interfere with the reception of the radio transmitter and reduce radio reception A WARNING LOCATING OPERATOR CONTROLS The light system controls must be located so that the VEHICLE and CONTROLS can be operated safely under all driving conditions Failure to observe this warning could result in driver distraction or driver error while operating the vehicle ETIN REVERSE POLARITY MISWIRING Reverse polarity may damage the lightbar and prevent operation To avoid damage to the lightbar ensure that the battery voltage is the same as the voltage of the lightbar and that the correct polarity is observed The lightbar must be fused at the source To wire the lightbar in the vehicle 1 Ensure that the lines are adequately fused see Figures 4 through 6 starting on page 17 From the lightbar route the CATS control cable into the vehicle s cab or trunk near the planned location of a control head that is compatible with the lightbar or Serial Interface Module NOTE An input cable 24 pin harness is provided with the Serial Interface Module For connections see Table 1 on page 9 and Figures 4 through 6 starting on page 17 Connect the 16 AWG black lead to the vehicle battery s ground NEG
20. terminal Connect the 16 AWG red lead through the supplied 15A fuse at the source to the positive BAT terminal SignalMaster Option The SignalMaster function 1s configured at the factory and does not require any additional wiring inside the lightbar All conductors necessary for control of the SignalMaster are through the compatible serial communication control head or the Serial Interface Module For wiring and operation refer to the instructions included with the control head or document P N 2562248 included with the Serial Interface Module Lightbar Controls Both the Federal Signal Serial Control Head and the Serial Interface Module provide the controls in Table 1 to the lightbar The table shows the corresponding control wires from the Serial Interface Module and their colors The wire s first color 1s the predominant color and additional colors are stripes For programming options see the instructions included with the Interface Module or the Federal Signal serial control head SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual Table 1 Rear ILS lightbar controls and their wires from the Serial Interface Module Green White Orange Black Low Power White Black Red Dims the lights approximately 50 percent to prevent blind ing approaching drivers Low Power is only available in Modes 1 and 2 and is disabled when switched to another flash pattern including Mode 3 and Intersection Test Pattern Black
21. to 65 C Unpacking the ILS After unpacking the ILS light assembly inspect it for damage that may have occurred in transit If it has been damaged do not install it File a claim immediately with the carrier stating the extent of damage Carefully check all envelopes shipping labels and tags before removing or destroying them Ensure that the parts listed in kit contents list are included in the package If you are missing any parts contact Customer Support at 1 800 264 3578 7 a m to 5 p m Monday through Friday CT Wiring the Rear ILS in the Vehicle Before proceeding ensure that the lightbar has been installed inside the vehicle in accordance with the instructions included with the mounting kit NOTE The DIP switch on the control PCB in the lightbar provides two selectable options To change DIP switch settings see Selecting Configuration Options on page 9 The lightbar is completely wired at the factory and does not require any additional internal wiring Two 16 AWG power conductors red and black and the CATS communication cable exit the lightbar The conductors necessary to control the lightbar are contained in the CATS cable which connects to a compatible Federal Signal control head or Serial Interface Module SpectraLux Rear ILS Lightbar Installation Maintenance and Service Manual A WARNING RADIO ANTENNA LOCATION Do not mount a radio antenna within 18 inches 45 7 cm of the lighting system Placing the an
22. to follow this warning may result in bodily injury or death to you or others To replace a reflector 1 2 Refer to the vehicle specific installation instructions included with the Rear ILS To remove the PCB that holds the reflector see Replacing a PCB on page 14 Use a small Phillips screwdriver to press and release the reflector s two round tabs from beneath the PCB Slide the reflector toward the rear of the PCB Figure 3 Lift the rear of the reflector away from the PCB and remove it Figure 3 Removing a reflector REMOVAL D PRESS THE ROUND TABS FROM BENEATH THE PCB AND SLIDE THE REFLECTOR BACK D LIFT THE REAR OF THE REFLECTOR TO REMOVE IT INSTALLATION 3 INSERT THE FRONT HOOKS IN THE PCB 4 BRING THE REAR OF THE REFLECTOR DOWN ON THE PCB AND INSERT THE REAR HOOKS INTO THE PCB 5 SLIDE THE REFECTOR FOWARD UNTIL IT SNAPS INTO PLACE 290A7045 To install the new reflector insert its front hooks into their slots on the PCB Bring the rear of the reflector down to insert its rear hooks through the PCB When the reflector rests on the PCB make sure the rear hooks are fully inserted and slide the reflector forward until its tabs snap into place Install the PCBs as described in steps 4 through 7 in Replacing a PCB on page 14 SpectraLux Rear ILS Lightbar 16 Installation Maintenance and Service Manual Ordering Replacement Parts This section contains a list of commo
Download Pdf Manuals
Related Search