MODEL Ultra-UV-R
Contents
1. Premier INSTALLATION OPERATION AND MAINTENANCE MANUAL Warning Please read carefully before proceeding with installation Your failure to follow any attached instructions or operating parameters may lead to the product s failure and possible damage to property MODEL Ultra UV R System Tested and certified by NSF International against ANSI NSF Standard 53 for the reduction of claims specified on the performance Coane data sheet Refer to enclosed warranty for operating parameters to ensure proper use with your water supply Watts Premier Inc 8716 W Ludlow Drive Suite 1 Peoria AZ 85381 Phone 800 752 5582 www premierH20 com Fax 623 866 5666 Manual 199334 Manual Date 8 06 05 Service Record Table of Contents Mainte ance Record oerna e a caer wdetmie cine sana cess eawsdswes agoad ea keseeeticed ss 3 Operational Parameters ices taiese re echelons dominance teen eeN aaa oes Sle seed 3 Contents of Ultra UNS RSV Ste my sec secescctexece zececenacesetesuassvesudsccesceencqee neue vend cena cenagsavesaaeoseee 3 Tools Recommended For Installation ccccccccseccceesseseeceeeceeseeeceeseeeeeeseessasaaeeees 3 instalation can Cesare cdacucceswtadenavariesenwsd a a ae O E e Ces e EE 3 Faucet Installation Sienen e a aa a ey 4 Adapt A Valve Installation iise medeea ee eeen eee aa EEEa ar Ea eE E eei 5 UV Lamp Replacement acrid iseinean ee i ee aa 6 UV R Diagrahnis itere aeee O E E E E E E A E rele 7 Preformance2. Unscrew UV cap counter clockwise Using a flat bladed screwdriver remove UV lamp from cap and discard Discard cap amp quartz tube if replacing at the same time as lamp G Clean inside of UV housing with warm soapy water Rinse with warm clean water to remove soap H Lubricate UV housing o ring with a water soluble lubricant i e K Y Jelly or Silicone lubricant NOTE Do not use Petroleum based lubricants such as Vaseline I Carefully slide new UV lamp into the cap and make sure the end plug is sealed Water cannot come into direct contact with the UV lamp Screw UV cap back on to UV housing body carefully by turning clockwise K Snap UV housing body back into single mounting clip Reconnect the 1 2 blue tubing back on to the UV housing body Repeat Step 4 Startup Jow mm ce m Item Part 1 OMOAN DOA FW ND Figure E UV Tube Assembly amp Exploded View Description 134008 Easy Tap Adapter 131017 Insert Brass 114 131012 Sleeve Delrin 114 131002 Nut Brass 114 C 140007 Tubing 114 Green 4ft 125034 Elbow 90 114 Cx 1 4 MPT 6 113004 Lid Black 114 FPT 113029 0 Ring For Filter Housing 101015 P CB I l Micron Carbon Block Gasket for Carbon Block 2 113017 Filter Housing 10 Blue 140004 Tubing 114 Blue 4ft Nut Lock Washer Black Locating Washer 116047 Black Rubber Washer 116053 Escutcheon Plate Item 17 18 19 20 21 22 23 24 p6 5 Seg Sink o K counte Part Descript
3. Data srein e a e Ee a e e EE EE EES EEEE 8 ATE TAEI AE AE T A EE ETELE E A EE E 9 Date of Purchase Date of Install Installed by DATE FILTER DATE FILTER DATE FILTER Thank you for your purchase of a UV R system With proper installation and maintenance this system will provide you with high quality water for years to come All of Watts Premier s water enhancement products are rigorously tested by independent laboratories for safety and reliability If you have any questions or concerns please contact our customer service depart ment at 1 800 752 5582 outside USA 480 675 7995 or refer to our online troubleshooting at www premierH20 com Operational Parameters Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Installation needs to comply with state and local plumbing regulations Maxim Minimum O 5 pH Parameters J OS 0 5 GPM 60 psie i O Contents of Ultra UV R System 1 Ultra UV R system 1 120V 60Hrz Transformer 1 Manual and Warranty Card If any of the items are missing please contact Watts Premier prior to installing Tools Recommended For Installation y small knife y variable speed Drill Vy 1 8 3 mm 1 4 6 4 mm and 7 16 11 0 mm drill bits V 1 2 and 5 8 open ended wrenches or adjustable wrenches y Phillips screwdriver Installation Step 1 Locate a space under the sink that allows the unit to be mounted
4. Micron Carbonblock P CB 1 CT 1 UC 1 UC 2 amp Ultra UV R 6 Months or 1350 gallons of water 170019 UV Replacement Lamp Ultra UV R 12 months or 9000 hours Testing parameters Flow rate 0 5 gpm pH 6 5 and 8 5 Water pressure 50 psi Cyst Reduction Gallons Influent Effluent 1 Effluent 2 Influent Avg 155500 count ml Fourth Cycle 98000 15 44 Effluent Avg 28 count ml 25 94000 4 15 Percent Reduction 99 98 50 160000 9 39 Maximum Effluent 81 count ml 75 270000 17 81 Lead Reduction 6 5 pH Gallons Sample Pt Influent Effluent 1 Effluent 2 Influent Avg 0 16 mg l 0 Start up 0 16 0 001 0 0013 Effluent Avg 0 0024 mg l 675 75 0 16 0 001 0 001 Percent Reduction 98 5 1350 100 0 16 0 0031 0 001 Maximum Effluent 0 0088 mg l 2025 150 0 17 0 0047 0 001 2430 180 0 17 0 0088 0 001 Lead Reduction 8 5 pH Gallons Sample Pt Influent Effluent 1 Effluent 2 Influent Avg 0 16 mg l 0 Start up 0 16 0 0017 0 01 Effluent Avg 0 0032 675 75 0 16 0 001 0 001 Percent Reduction 98 1350 100 0 17 0 001 0 001 Maximum Effluent 0 01 mg l 2025 150 0 14 0 0033 0 0058 2430 180 0 16 0 0058 0 0011 That the systems conform to ANSI NSF 53 for specific performance claims as verified and substantiated by test data REFER TO OWNER S INSTALLATION SERVICE MANUAL FOR FURTHER MAINTENANCE REQUIREMENTS AND WARRANTY INFORMATION Phone 480 675 7995 Fax 623 866 5666 Premier 8716 W Ludlow Drive Suite 1 e Peoria AZ 85381 Limited Warranty What your Warranty Cov
5. ace B Place a piece of masking tape or duct tape on location where the hole Long Reach Spout is to be drilled Mark the center of the hole on the tape Note Stainless steel sinks go to Step F Porcelain Sinks T Fret Body C Using the variable speed drill on the slowest speed drill a 1 8 3 0 mm pilot hole at the center of the desired location Use lubricating Eeeh oil or liquid soap to keep the drill bit cool while drilling Note If Plate drill bit gets hot it may cause the porcelain to crack or chip Pilot hole must be drilled through both porcelain and metal casing of the sink before proceeding to the next step D Enlarge pilot hole to 1 4 6 4 mm Keep drill speed on the slowest oa speed and use lubricating oil or liquid soap to keep drill bit cool 1 E Enlarge the hole to 7 16 11 13 mm Keep drill speed on the 8 slowest speed and use lubricating oil or liquid soap to keep drill bit m cool F Pass the Escutcheon plate and black rubber washer over threaded mounting tube at the base of the faucet body G From top of sink pass the threaded mounting tube through the hole drilled in the sink Align the faucet body H From under the sink slide the locating washer and the lock washer over the threaded part of the faucet tube Screw on retaining nut Tighten with wrench Connect the loose end of the 1 4 blue plastic tubing from the filtration unit to the threaded mount
6. close to the cold water supply and allows for easy access during maintenance and filter changes System must be installed to the cold water supply only Allow 2 5cm clearance between the bottom of the filter housing and the floor of the sink cabinet Using the mounting hole on the bracket mark the location for the mounting screws on the cabinet wall under the sink Screw the 2 screws into the wall at the marked location The Ultra UV R bracket is designed to be mounted without removing the screws Hang the Ultra UV R 2 module on the screws using the mounting holes in the bracket Step 2 Special Note Porcelain sink surface material is extremely hard and can crack or chip quite easily Use extreme caution if drilling Watts Premier accepts no responsibility for consequential damage resulting from the installation of faucet to the sink or counter top Colored faucets can be ordered through Watts Premier s toll free customer service department by calling 1 800 752 5582 in the Continental United States online at www premierH20 com or 480 675 7995 outside the United States A Remove faucet kit from plastic bag and locate each of the following parts Note Remove plastic tubing from faucet body before inserting long reach spout into faucet body as shown in Figure A Figure A Faucet tube connection Note If using existing hole sprayer or soap dispenser go to Step G A Determine desired location for the faucet on your sink surf
7. ers If any part of your WATTS PREMIER Ultra UV R is defective in workmanship excluding replaceable filters and uv bulbs return unit after obtaining a return authorization see below within 3 year of original retail purchase WATTS PREMIER will repair or at WATTS PREMIER S option replace the system at no charge How to obtain Warranty Service For warranty service call 1 800 752 5582 for a return authorization number Then ship your unit to our factory freight and insurance prepaid with proof of date of original purchase Please include a note stating the problem Premier will repair it or replace it and ship it back to you prepaid What this warranty does not cover This warranty does not cover defects resulting from improper installation contrary to WATTS PREMIER S printed instructions from abuse misuse misapplication improper maintenance neglect alteration accidents casualties fire flood freezing environmental factors water pressure spikes or other such acts of God This warranty will be void if defects occur due to failure to observe the following conditions The Ultra UV R System must be hooked up to a potable municipal or well cold water supply The pH of the water must not be lower than 5 or higher than 10 The incoming water pressure must be between 20 and 100 pounds per square inch Incoming water to the Ultra UV R cannot exceed 100 degrees F 40 degrees C Incoming TDS Total Dissolved Solids not to exceed 1800 p
8. ing tube of the faucet as shown in Figure B I a I E Black Rubber Washer e oc ting Washer Lockng Washer Retaining Nut 14 Brass Insert 14 De rin Sleeve 14 Brass Compression Nut Figure B Faucet tube connection Faucet threaded mounting tube Brass insert goes inside of tubing Delrin sleeve beveled end faces end of tubing Brass compression nut Blue tube Step 3 Installation of r A Valve i34007 For 3 8 Plumbing For 2 Plumbing Hot water supply line Cold water supply line Step 1 Turn off the cold water supply to the faucet by turning the angle stop valve off Step 2 Attach the Adapta Valve as illustrated in the photo above When attaching to straight pipe threads use Teflon tape on the threads Step 3 Attach the Green tube into the Adapt Valve Securing the connection Step 4 Lift black faucet handle up on faucet to start flow of water through unit Run 7 gallons of water through unit Close faucet Note You may hear some noise as air is being purged from the unit and the first few glasses of water through the unit may be dark in color due to carbon fines B Check for leaks If you have any leaks shut off water supply to system repair and restart unit C Connect plastic electrical connector from UV unit to the plastic electrical connector from AC adapter D Plug adapter into GFCI electrical outlet You will see a pale blue light from the view por
9. ion Faucet Body 116032 L R Spout 137046 UV Bracket 146001 10 3 4 Philip Pan Head Screws 6 146004 10 1 Philip Pan Head Screw 2 164004 Single Mounting Clip 104015 CTG 10 5 Micron Sediment Module Includes 170001 Body Cap Quartz tube O ring amp UV lamp 170019 UV Reptacement Lamp ST 200 UV lamp Ballast 170007 100v 50Hz 170010 120v 60Hz 170014 220v 50Hz 170015 240v 50Hz Watts Premier Inc 8716 W Ludlow Drive Suite 1 Peoria AZ 85381 USA Performance Data Sheet for specific claims to NSF Std 53 CT 1 UC 1 UC 2 amp Ultra UV R GENERAL USE CONDITIONS 1 System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality DO NOT use with water that is microbiologically unsafe or unknown quality without adequate disinfection before and after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts 2 Operating Temperature Maximum 100 F 40 5 C Minimum 40 F 4 4 C 3 Operating Water Pressure Maximum 100 psi 7 43 kg cm Minimum 20 psi 4 Turbidity lt 5 NTU 5 pH 5 to 10 6 Maximum flow Rate 0 50 gpm 1 89 Ipm RECOMMENDED REPLACEMENT PARTS AND CHANGE INTERVAL Note Depending on incoming feed water conditions replacement time frame may vary Description Units Change time Frame Stage 1 sediment 5M 10 UC 2 amp Ultra UV R 6 Months or 1350 gallons of water 1
10. pm Do not use with water that is micro biologically unsafe or of unknown quality without adequate disinfection before or after the system ONOAN gt This warranty does not cover any equipment that is relocated from the site of its original installation This warranty does not cover any equipment that is installed or used outside the United States of America and Canada LIMITATIONS AND EXCLUSIONS WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTIBILITY AND FITNESS FORA PARTICULAR PURPOSE WATTS PREMIER WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING TRAVEL EXPENSE TELEPHONE CHARGES LOSS OF REVENUE LOSS OF TIME INCONVENIENCE LOSS OF USE OF THE EQUIPMENT AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO FUNCTION PROPERLY THIS WARRANTY SETS FORTH ALL OF PREMIER S RESPONSIBILITIES REGARDING THIS EQUIPMENT OTHER CONDITIONS If WATTS PREMIER chooses to replace the equipment WATTS PREMIER may replace it with reconditioned equipment Parts used in repairing or replacing the equipment will be warranted for 90 days from the date the equipment is returned to you or for the remainder of the original warranty period whichever is longer This warranty is not assignable or transferable YOUR RIGHTS UNDER STATE LAW Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of incidental or conseq
11. t on the UV Housing body The light indicates that the UV lamp is on and working Important guidlines Do not unplug UV unit from power supply Turning system off amp on will shorten the life of the UV lamp UV should be on continuously for maximum effectiveness The system requires a warm up period for proper operation Wait 20 minutes after plugging in the system before using water Water not drawn from unit for a period of time may have a taste or odor and will be warm To avoid this allow water to run through the system for one minute before using Replacement filters for this and many other filtration systems can be purchased directly from Watts Premier Ordering options include mail order telephone ordering and online filter replacement Additionally Watts Premier sells filtration and reverse osmosis systems suitable for almost any individual or commercial application Replacing UV lamp Cap amp Quartz Tube Warning Do not touch UV Lamp or Quartz Tube with bare fingers or hands Fingerprints on the lamp or tube may reduce lamp effectiveness Handle with clean cloth or gloves Unplug ballast from GFCI electrical outlet Unplug the plastic electrical connector from ballast to UV Lamp Turn off water supply to the unit Lift faucet handle to relieve water pressure Disconnect both plastic tubes from the UV housing body by turning the white plastic nuts counter clockwise Remove the UV housing from the single mounting clip
12. uential damages so the above limitations or exclusions may not apply This warranty gives you specific legal rights and you may have other legal rights which vary from state to state Premier Watts Premier Inc 8716 W Ludlow Drive Suite 1 Peoria AZ 85381 Phone 800 752 5582 www premierH20 com Fax 623 866 5666
Download Pdf Manuals
Related Search