SEAT BELT RETRACTOR : Removal and
Contents
1. 7 Revision 2009 March SB 1 2009 FX35 FX50 PRECAUTIONS lt PRECAUTION gt PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System SRS AIR BAG and SEAT BELT R E T E N S O N E R INFOID 0000000004052200 The Supplemental Restraint System such as AIR and SEAT BELT PRE TENSIONER used along with a front seat belt helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision This system includes seat belt switch inputs and dual stage front air bag modules The SRS system uses the seat belt switches to determine the front air bag deployment and may only deploy one front air bag depending on the severity of a collision and whether the front occupants are belted or unbelted Information necessary to service the system safely is included in the SRS AIR BAG and SEAT BELT of this Service Manual WARNING To avoid rendering the SRS inoperative which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation all maintenance must be performed by an authorized NISSAN INFINITI dealer Improper maintenance including incorrect removal and installation of the SRS can lead to personal injury caused by unintentional activation of the system For removal of Spiral Cable and Air Bag Module see the SRS AIR BAG Do not use electrical test equipment on any circuit relat2. Road surface must be paved and dry Never perform the following test on wet or gravel roads public streets or and highways This could result in an accident and serious per sonal injury The driver and passenger must be prepared to brace themselves in the event that the retractor does not lock 1 Fasten driver seat belt Buckle a passenger into the seat for the belt that is to be tested 2 Proceed to the designated safe area 3 Drive the vehicle at approximately 16 km h 10 MPH Notify any passengers of a pending sudden stop And that the driver and passenger must be prepared to brace themselves in the event that the retractor does not lock Apply brakes firmly and make a very hard stop During stopping seat belts should lock and not be extended If the seat belt retractor assembly does not lock perform the retractor off vehicle check SEAT BELT RETRACTOR OFF VEHICLE CHECK 1 Remove the front seat belt retractor Refer to SB 6 SEAT BELT RETRACTOR Removal and Installa tion 2 Slowly pull out webbing while tilting the retractor assembly forward from the mounted position without twisting the retractor assembly as shown in the figure The webbing can be pulled out when the angle A is 22 degrees or less The webbing cannot be pulled out when the angle B is 37 degrees or more A and B Tilting angles lt a Vehicle front 954 3 Replace the seat belt assembly if it does not operate normall
3. and push lock into connec tor After installing the connector check that the lock is pushed t 4 securely into it Remove the pretensioner seat retractor fixing bolt and anchor bolt PHIA0953J 4 Remove the seat belt adjuster Remove the seat belt adjuster fixing bolts INSTALLATION Install in the reverse order of removal SEAT BELT BUCKLE SEAT BELT BUCKLE Inspection INFOID 00000000039 10481 AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attached hardware after any collision NISSAN INFINITI recommends that all seat belt assemblies in use during a collision be replaced gt unless the collision is minor and the belts show no damage and continue to operate normally Not doing so could result in serious personal injury in an accident Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted Seat belt pre ten sioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if The seat belt is in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate normally The seat belt is damaged an accident i e torn webbing bent retractor or guide etc The seat belt attaching point is damaged in an ac
4. the driver seat belt also have an Automatic Locking Retractors ALR mode The ALR mode also called child restraint mode is used when installing child seats The ALR mode is activated when the seat belt is fully extended When the webbing is then retracted partially the ALR mode automatically locks the seat belt in a specific position so that the webbing cannot be extended any further To cancel the ALR mode allow the seat belt to fully wind back into the retractor Check the seat belt retractors with the following test s to determine if a retractor assembly is operating prop erly ELR Function Stationary Check Grasp the shoulder webbing and pull forward quickly The retractor should lock and prevent the belt from extending further ALR Function Stationary Check 1 Pull out the entire length of seat belt from retractor until a click is heard 2 Retract the webbing partially A clicking noise should be heard as the webbing retracts indicating that the retractor is in the Automatic Locking Retractors ALR mode 3 Grasp the seat belt and try to pull out the retractor The webbing must lock and not extend any further If it does not operate normally replace the retractor assembly 4 Allow the entire length of the webbing to retract to cancel the automatic locking mode SE ELR Function Moving Check WARNING Perform the following test in a safe open area clear of other vehicles and obstructions for example a large empty parking lot
5. 62 degrees or more A and B Tilting angles lt I Vehicle front 997 b Center seat belt retractor The webbing can be pulled out when the angle A is 24 degrees or less The webbing cannot be pulled out when the angle B is 39 degrees or more A and B Tilting angles lt I Vehicle front 056122 3 Replace the seat belt assembly if it does not operate normally Revision 2009 March SB 10 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt 5 E LT R ET RACTO R Exploded Vi ew INFOID 00000000039 10485 SEC 869 JMHIA0706GB 1 Retaining washer 2 Spacer 3 Shoulder anchor 4 Anchor bolt 5 Rear seat belt escutcheon 6 Outer seat belt retractor 7 Outer anchor 8 Inner anchor 9 Outer seat belt buckle 10 Center seat belt buckle 11 Seat belt finisher 12 Seat belt guide upper 13 Seat belt guide lower 14 Center seat belt retractor cover 15 Anchor nut 16 Center seat belt retractor 17 Seat back frame Refer to Gl 4 Components for symbols in the figure SEAT BELT RETRACTOR Removal and Installation INFOID 0000000003910486 REMOVAL 1 Remove the outer anchor Remove the rear seat cushion Refer to SE 83 Removal and Installation Remove the outer anchor fixing anchor bolt and then remove the outer anchor 2 Remove the inner anchor Revision 2009 March SB 11 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION
6. G Perform the following test in a safe open area clear of other vehicles and obstructions for example a large empty parking lot Road surface must be paved and dry Never perform the following test on wet or gravel roads or on public streets or highways This could result in an accident and serious personal injury The driver and passenger must be prepared to brace themselves in the event that the retractor does not lock 1 Fasten driver seat belt Buckle a passenger into the seat for the belt that is to be tested 2 Proceed to the designated safe area 3 Drive the vehicle at approximately 16 km h 10 MPH Notify any passengers of a pending sudden stop and that the driver and passenger must be prepared to brace themselves in the event that the retractor does not lock Apply brakes firmly and make a very hard stop During stopping seat belts should lock and not be extended If the seat belt retractor assembly does not lock perform the retractor off vehicle check SEAT BELT RETRACTOR OFF VEHICLE CHECK 1 Remove the rear seat belt retractor Refer to SB 11 SEAT BELT RETRACTOR Removal and Installa tion 2 Slowly pull out webbing while tilting the retractor assembly forward from the mounted position without twisting the retractor assembly as shown in the figure a Outer seat belt retractor The webbing can be pulled out when the angle A is 47 degrees or less The webbing cannot be pulled out when the angle B is
7. RESTRAINTS SECTION S B SEAT BELT CONTENTS PREGAU TION 2 SEAT BELT BUCKLE Exploded View 8 SEAT BELT BUCKLE Removal and Installation 8 PRECAUTIONS 2 Precaution for Supplemental Restraint System REAR SEAT BELT teen dew 9 pa aid OEN EAEE PRE 5 SEAT BELT RETRACTOR tiniani 9 Precaution for Seat Belt Service ee tee A 2 SEAT BELT RETRACTOR Inspection 9 ye gers ge any SEAT BELT RETRACTOR Exploded View 11 REMOVAL AND INSTALLATION 4 SEAT BELT RETRACTOR Removal and Instal DATO Me E nM eet 11 FRONT SEATBELT cain SEAT BELT BUCKLE 13 SEAT BELT RETRACTOR 4 SEAT BELT BUCKLE Inspection 13 SEAT BELT RETRACTOR Inspection 4 SEAT BELT BUCKLE Exploded View 15 SEAT BELT RETRACTOR Exploded View 6 SEAT BELT BUCKLE Removal and Installation 15 BOT ee and insta SYSTEM FOR CHILDREN u 17 Exploded VIEW ekien ITERE E AIE 17 SEAT BELT BUCKLE 7 Removal and Installation 17 SEAT BELT BUCKLE Inspection
8. and repair if necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out The seat belt pre tensioners should be replaced even if the seat belts are in use during the collision in which the air bags are deployed PRELIMINARY CHECKS 1 Check the seat belt warning lamp for proper operation as per the following a Turn ignition switch ON The seat belt warning lamp should illuminate b Fasten driver seat belt The seat belt warning lamp should turn OFF 2 If the air bag warning lamp is blinking perform self diagnosis using CONSULT III and air bag warning lamp Refer to SRC 16 Diagnosis Description Check that the seat belt retractor seat belt anchor and buckle bolts are tightened firmly 4 Check the shoulder seat belt guide and shoulder belt height adjuster for front seats Check that guide swivels freely and that webbing lays flat and does not bind in guide Check that height adjuster operate normally and holds securely 5 Check retractor operation a Fully extend the seat belt webbing and check for twists tears or other damage b Allow the seat belt to retract Check that webbing returns smoothly and completely into the retractor If the seat belt does not return smoothly wipe the inside of the loops with a clean paper cloth Dirt build up in the loops of the upper anchors can cause the seat belts to retract slowly c Fasten the seat belt Check that seat belt returns smoothly a
9. bbing is cut frayed or damaged replace seat belt assembly When replacing seat belt assembly use a Genuine NISSAN seat belt assembly AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attached hardware after any collision Should NISSAN recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate normaly Failure to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a col lision should also be replaced if either damage or improper operation is noted Seat belt pre tension ers should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if Revision 2009 March SB 2 2009 FX35 FX50 PRECAUTIONS lt PRECAUTION gt The seat belt is in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate normaly The seat belt is damaged an accident i e torn webbing bent retractor or guide The seat belt attaching point is damaged in an accident Inspect the seat belt attaching area for damage distortion and repair as necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out The front seat belt pre te
10. cident Inspect the seat belt attaching area for damage distortion and repair if necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed PRELIMINARY CHECKS 1 Check the seat belt warning lamp for proper operation as per the following a Turn ignition switch ON The seat belt warning lamp should illuminate b Fasten driver seat belt The seat belt warning lamp should turn OFF 2 If the air bag warning lamp is blinking perform self diagnosis using CONSULT III and air bag warning lamp Refer to SRC 16 Diagnosis Description Check that the seat belt retractor seat belt anchor and buckle bolts are tightened firmly 4 Repeat the steps above if necessary to check the other seat belts Revision 2009 March SB 7 2009 FX35 FX50 FRONT SEAT BELT lt REMOVAL AND INSTALLATION gt S EAT B E LT B U KL E loded View INFOID 0000000003910482 JMHIA0705GB 1 Anchor bolt 2 Wave washer 3 Seat belt buckle 4 Plain washer 5 Retaining washer 6 Seat belt buckle harness connector Refer to 01 4 Components for symbols in the figure SEAT BELT BUCKLE Removal and Installation INFOID 0000000003910483 REMOVAL Remove the seat belt buckle Remove the front seat from vehicle Refer to SE 73 Removal and Installation For ease o
11. ed to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and or orange harnesses or har ness connectors PRECAUTIONS WHEN USING POWER TOOLS AIR OR ELECTRIC AND HAMMERS WARNING When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running DO NOT use air or electric power tools or strike near the sensor s with a hammer Heavy vibration could activate the sensor s and deploy the air bag s possibly causing serious injury When using air or electric power tools or hammers always switch the ignition OFF disconnect the battery and wait at least 3 minutes before performing any service Precaution for Seat Belt Service CAUTION Before removing the front seat belt pre tensioner assembly turn the ignition switch OFF disconnect the battery negative terminal and wait at least 3 minutes Never use electrical test equipment for front seat belt pre tensioner connector After replacing or reinstalling front seat belt pre tensioner assembly or reconnecting front seat belt pre tensioner connector check the system function Refer to SRC 16 Diagnosis Description Never use disassembled buckle or seat belt assembly Replace anchor bolts if they are deformed or worn out Never oil tongue and buckle If any component of seat belt assembly is questionable never repair Replace the entire seat belt assembly If we
12. f tool operation in narrow space Remove the seat belt buckle harness connector and harness clamp Remove the seat belt buckle fixing anchor bolt INSTALLATION Install in the reverse order of removal Revision 2009 March SB 8 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt REAR SEAT BELT SEAT BELT RETRACTOR S EAT B E LT R ET RACTO R A n spect n INFOID 0000000003910484 AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attached hardware after any collision NISSAN INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision is minor and the belts show no damage and continue to operate normally Not doing so could result in serious personal injury in an accident Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted Seat belt pre ten sioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if The seat belt is in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate normally The seat belt is damaged in an accident i e torn webbing bent retractor or guide etc The seat belt attaching point is damaged in an acciden
13. gt Remove the inner anchor fixing anchor bolt and then remove the inner anchor 3 Remove the shoulder anchor Remove the luggage side upper and lower finisher Refer to 29 Removal and Installation Remove the shoulder anchor fixing anchor bolt and then remove the shoulder anchor 4 Remove the outer seat belt retractor Remove the luggage side upper and lower finisher Refer to INT 29 Removal and Installation Remove the fixing anchor bolt and then remove the outer seat belt retractor 5 Remove the center seat belt retractor Remove rear seat cushion Refer to SE 83 Removal and Installation Remove rear center seat belt anchor bolt Refer to SB 11 SEAT BELT RETRACTOR Exploded View Remove the pawls and then remove seat belt finisher A Pawl 7 ae 1 1 1 1 1 1 1 1 i 0 4 A JMHIA0562ZZ Remove seatback board RH Refer to SE 84 Disassembly and Assembly Disengage rear center seat belt retractor cover 1 fixing pawls A Pawl Lod e Remove rear center seat belt retractor fixing nut A with a socket wrench B JMHIA0738ZZ Revision 2009 March SB 12 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt e Remove rear center seat belt retractor 1 and retractor cover simultaneously from rear seatback frame JMHIA0739ZZ Remove hog rings A f
14. kle Remove the rear seat cushion Refer to SE 83 Removal and Installation Remove the center and outer seat belt buckle fixing anchor bolt INFOID 00000000039 10489 Revision 2009 March SB 15 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt INSTALLATION Install in the reverse order of removal Revision 2009 March SB 16 2009 FX35 FX50 LATCH SYSTEM FOR CHILDREN lt REMOVAL AND INSTALLATION gt LATCH SYSTEM FOR CHILDREN E X p od ed ew INFOID 00000000039 10490 ds V UMHIA0707GB 1 LATCH system Refer to Gl 4 Components for symbols in the figure SB Removal and Installation INFOID 0000000003910491 REMOVAL CAUTION Replace anchor bolts if they are deformed or worn out 1 Remove the rear seat cushion Refer to SE 83 Removal and Installation 2 Remove mounting bolts and remove LATCH Lower Anchor and Tether for Children system INSTALLATION Install in the reverse order of removal Revision 2009 March SB 17 2009 FX35 FX50
15. ll 3 point type seat belt retractors except the driver seat belt also have an Automatic Locking Retractors ALR mode The ALR mode also called child restraint mode is used when installing child seats The ALR mode is activated when the seat belt is fully extended When the webbing is then retracted partially the ALR mode automatically locks the seat belt in a specific position so that the webbing cannot be extended any further To cancel the ALR mode allow the seat belt to fully wind back to the retractor Check the seat belt retractors with the following test s to determine if a retractor assembly is operating nor mally ELR Function Stationary Check Grasp the shoulder webbing and pull forward quickly The retractor should lock and prevent the belt from extending further ALR Function Stationary Check 1 Pull out the entire length of seat belt from retractor until a click is heard 2 Retract the webbing partially A clicking noise should be heard as the webbing retracts indicating that the retractor is in the Automatic Locking Retractors ALR mode Revision 2009 March SB 9 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt 3 Grasp the seat belt and try to pull out the retractor The webbing must lock and not extend any further If it does not operate normally replace the retractor assembly 4 Allow the entire length of the webbing to retract to cancel the automatic locking mode ELR Function Moving Check WARNIN
16. nd completely to the retractor If the webbing does not return smoothly the cause may be an accumulation of dust or dirt Use the SEAT BELT TAPE SET and perform the following steps Inspect the front seat belt through anchor 1 Pull the seat belt out to a length of 500 mm 19 69 in or more 2 Fix the seat belt at the center pillar webbing opening with a clip or similar device 3 Pass thin wire through the through anchor webbing opening Hold both ends of the wire and pull it tightly while moving it up and down several times along the webbing opening surface to remove dirt stuck there 4 dirt that cannot be removed with the wire can be removed by cleaning the opening with a clean cloth 5 Apply tape at the point where the webbing contacts the through anchor webbing opening NOTE Apply the tape so that there is no slack or wrinkling 6 Remove the clip fixing the seat belt and check that the webbing returns smoothly 6 Repeat the steps above if necessary to check the other seat belts Revision 2009 March SB 4 2009 FX35 FX50 FRONT SEAT BELT lt REMOVAL AND INSTALLATION gt SEAT BELT RETRACTOR ON VEHICLE CHECK Emergency Locking Retractors ELR and Automatic Locking Retractors ALR NOTE All seat belt retractors are Emergency Locking Retractors ELR type In an emergency sudden stop the retractor locks and prevents the webbing from extending any further All 3 point type seat belt retractors except
17. nsioner must be replaced even if the seat belts are not in use during the collision in which the air bags are deployed Revision 2009 March SB 3 2009 FX35 FX50 FRONT SEAT BELT lt REMOVAL AND INSTALLATION gt REMOVAL AND INSTALLATION FRONT SEAT BELT SEAT BELT RETRACTOR S EAT B E LT R ET RACTO R spect n INFOID 0000000003910478 AFTER A COLLISION WARNING Inspect all seat belt assemblies including retractors and attached hardware after any collision NISSAN INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision was minor and the belts show no damage and continue to operate normally Not doing so could result in serious personal injury in an accident Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted Seat belt pre ten sioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if The seat belt is in use at the time of a collision except for minor collisions and the belts retractors and buckles show no damage and continue to operate normally The seat belt is damaged in an accident i e torn webbing bent retractor or guide etc The seat belt attaching point is damaged in an accident Inspect the seat belt attaching area for damage or distortion
18. ors and buckles show no damage and continue to operate normally The seat belt is damaged an accident i e torn webbing bent retractor or guide etc The seat belt attaching point is damaged in an accident Inspect the seat belt attaching area for damage or distortion and repair if necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out The seat belt pre tensioner should be replaced even if the seat belts are not in use during the collision which the air bags are deployed PRELIMINARY CHECKS 1 Check that the seat belt retractor seat belt anchor and buckle bolts are tightened firmly 2 Repeat the step above if necessary to check the other seat belts Revision 2009 March SB 14 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt SEAT BELT BUCKLE Exploded View INFOID 0000000003958465 SEC 869 JMHIA0706GB 1 Retaining washer 2 Spacer 3 Shoulder anchor 4 Anchor bolt 5 Rear seat belt escutcheon 6 Outer seat belt retractor 7 Outer anchor 8 Inner anchor 9 Outer seat belt buckle 10 Center seat belt buckle 11 Seat belt finisher 12 Seat belt guide upper 13 Seat belt guide lower 14 Center seat belt retractor cover 15 Anchor nut 16 Center seat belt retractor 17 Seat back frame Refer to 1 4 Components for symbols in the figure SEAT BELT BUCKLE Removal and Installation REMOVAL Remove the center and outer seat belt buc
19. rom seatback upper side e Remove seat belt guide upper fixing screws A and then remove seat belt guide upper 1 JMHIA0741ZZ Remove rear center seat belt assembly INSTALLATION Install in the reverse order of removal CAUTION Push the center seat belt webbing 1 to place center seat belt webbing between seatback RH and reclining device inner cover not in front of LATCH striker as shown in the figure before installing seat cushion SEAT BELT BUCKLE SEAT BELT BUCKLE Inspection INFOID 00000000039 10487 AFTER A COLLISION WARNING Revision 2009 March SB 13 2009 FX35 FX50 REAR SEAT BELT lt REMOVAL AND INSTALLATION gt Inspect all seat belt assemblies including retractors and attached hardware after any collision NISSAN INFINITI recommends that all seat belt assemblies in use during a collision be replaced unless the collision is minor and the belts show no damage and continue to operate normally If not to do so could result in serious personal injury in an accident Seat belt assemblies not in use during a collision should also be replaced if either damage or improper operation is noted Seat belt pre ten sioners should be replaced even if the seat belts are not in use during a frontal collision in which the air bags are deployed Replace any seat belt assembly including anchor bolts if The seat belt is in use at the time of a collision except for minor collisions and the belts retract
20. t Inspect the seat belt attaching area for damage distortion and repair if necessary before installing a new seat belt assembly Anchor bolts are deformed or worn out The seat belt pre tensioners should be replaced even if the seat belts are not in use during the collision in which the air bags are deployed PRELIMINARY CHECKS 1 Check that the seat belt retractor seat belt anchor and buckle bolts are tightened firmly 2 Check retractor operation a Fully extend the seat belt webbing and check for twists tears or other damage b Allow the seat belt to retract Check that webbing returns smoothly and completely to the retractor If the seat belt does not return smoothly wipe the inside of the loops with a clean paper cloth Dirt build up in the loops of the upper anchors can cause the seat belts to retract slowly c Fasten the seat belt Check that seat belt returns smoothly and completely to the retractor If the webbing does not return smoothly the cause may be an accumulation of dust or dirt Use the SEAT BELT TAPE SET and perform the following steps 3 Repeat the steps above if necessary to check the other seat belts SEAT BELT RETRACTOR ON VEHICLE CHECK Emergency Locking Retractors ELR and Automatic Locking Retractors ALR NOTE All seat belt retractors are Emergency Locking Retractors ELR type In an emergency sudden stop the retractor locks and prevents the webbing from extending any further A
21. y Revision 2009 March SB 5 2009 FX35 FX50 FRONT SEAT BELT lt REMOVAL AND INSTALLATION gt SEAT BELT RETRACTOR Exploded View INFO1D 0000000003910479 SEC 868 JMHIA0704GB 1 Pre tensioner seat belt retractor 2 Anchor bolt 3 lt seat belt connector 4 Seat belt pre tensioner connector 5 Outer anchor cover 6 Outer anchor 7 Spacer 8 Spring washer 9 Retaining washer 10 Anchor nut 11 Shoulder anchor 12 Seat belt adjuster Refer to 01 4 Components for symbols in the figure SEAT BELT RETRACTOR Removal and Installation INFOID 0000000003910480 REMOVAL CAUTION Before servicing SRS turn the ignition switch OFF disconnect the battery negative terminal and wait at least 3 minutes REMOVAL 1 Remove the outer anchor Remove the outer anchor cover Remove the seat belt anchor fixing anchor bolt 2 Remove the shoulder anchor Remove the center pillar upper and lower garnish Refer to INT 17 Removal Installation Remove the shoulder anchor fixing anchor nut 3 Remove the seat belt assembly Disconnect the seat belt pre tensioner connector and pre crash seat belt connector NOTE Revision 2009 March SB 6 2009 FX35 FX50 FRONT SEAT BELT lt REMOVAL AND INSTALLATION gt e For installing removing seat belt pre tensioner connector insert thin screwdriver wrapped in tape into notch lift lock and remove connector Install connector with lock raised
Download Pdf Manuals
Related Search