installation manual parking sensor system
Contents
1. be damaged Two of the sensors are not connected properly or may be damaged Three or more of the sensors are not connected properly or may be damaged The sensor s harness has not been connected to the ECU Confirmation Method Confirm whether the buzzer plug is inserted Check if reverse lights are on or that the thick white wire has been spliced Check whether the fuse has been blown Confirm whether the ECU is damaged Confirm whether the sensors are properly connected Confirm whether each sensor functions properly Confirm whether the sensors are properly connected and whether each sensor functions properly Confirm whether the sensors are properly connected and whether each sensor functions properly Confirm whether the harness has been connected properly Insert the buzzer plug correctly Splice the thick white wire Replace the fuse with a new one Replace ECU witha new one Connect the plug of each sensor properly Replace any damaged sensor with a new one Connect the plug of each sensor properly and replace any damaged sensors with a new one Connect the plug of each sensor properly and replace any damaged sensors with a new one Connect the plug of the harness to the ECU The gear is in R but the warning does not go off although there are objects behind the vehicle The gear is in R and the warning goes off for a while al2. or removing parts Loosen or tighten bolts Use a Phillips screw and nuts using tools driver that fits the that match their sizes recess in the head of the screw being loos ened or tightened Before installation Be sure to disconnect the negative terminal cable from the battery To remove plastic parts use a trim remover Do notlet harnesses be pinched between parts Do not pull on wiring harnesses strongly When disconnecting connectors first unlock them then separate the connectors by pulling on themselves not on cables When connecting con nectors push them against each other until the lock clicks S f AAA Slick Protect the harness from sharp edges by covering the edges with tape or other suitable materials Do not fasten the har ness to brake pipes or high pressure air condi tioner pipes Apply sealant to grom mets at portions where the harness run through Route the harness away from hot compo nents such as the engine and radiator Clamping harness After installation Fasten the additional Bind up extra length of Check the product and Check the installed harness to an existing the harness using a tie wiring for installed con product for function vehicle harness using wrap dition before connect Also check lamps tape or tie wraps ing the cable
3. INSTALLATION MANUAL PARKING SENSOR SYSTEM Thank you for purchasing MITSUBISHI genuine PARKING SENSOR SYSTEM This manual explains the procedure for installing PARKING SENSOR SYSTEM Read this manual thoroughly before installation to ensure proper work PART NUMBER APPLICABLE MODEL MZ380466EX Outlander Sport COMPONENT PARTS 2 SENSOR 4 3 BUZZER 4 SENSOR CLIP 4 5 MAIN HARNESS 8 TEMPLATE A B 10 SENSOR LOCATION 9 STICKERS STICKER 11 CABLE TIE 24 2 6260 TOOLS NECESSARY FOR INSTALLATION SCREWDRIVER SOCKET WRENCH 10 ORNAMENT REMOVER S Cr HOLE SAW DRILL BIT 24mm 26mm 3mm 15mm s ESISISIIISIJ lt a ae MITSUBISHI MOTORS Template B RVR DOCK Barca ar D0 40 30 20 10 0 Template A TIT D0 AU 3U 20 10 U DU 40 30 40 RVR Corner Unit mm PRECAUTIONS Disconnect the negative pole cable from the battery before installation in order to avoid possible electric shock or bodily injury 1 The parking sensor system detects the distance between a vehicle and obstacles nearby when the vehicle moves backward and warns the driver of the distance with buzzer sound It is designed as a tool to enhance a driver s comfort but is not intended to relieve the driver s safety responsibility Please remember to take all usual care even when using this system 2 As there is time lag between detection and real warning please park your car a
4. a steep incline Refer to service manual for figure
5. f wiring harness when install the terminal to the connector No Line color 22 Restore the rear end harnesses and the taping and tie the sensor harnesses at the locations specified in the picture 23 When restoring the rear end harnesses make sure that the sensor harness connector A of fig 21 is positioned as shown in the picture 24 For vehicles without rear end harnesses make a small cross slit on the blindfold plug with knife and route the Sensor harnesses B through it we 25 Refer to the picture for the Main Harness routing inside the vehicle 14 the specified in the picture the unit Make sure not to install the ECU within the area marked by 2 in order to prevent its interference with the rear quarter trim the specified in the picture NOTE Insufficient installation and BJ locking of splice connector may cause disconnection confirm the wire location Back up lamp when locking and make sure to lock firml Connect Sensor harness B and Main Harness nu u oe L specified in the 15 29 For vehicles without rear end harnesses tie the main harnesses at the locations specified in the picture 30 Connect the sensor harnesses and restore the bumper 31 Make a 15 hole at the location specified in the picture on the rear quarter panel on the left side 16 17 32 Remove release paper from the back of the buzzer route the buzzer cables t
6. hrough the 15 hole and attach the buzzer to the trim 33 Bind up 200mm of the buzzer cables and fix them to the trim with stickers as shown in the picture 34 Connect the 2 pin connectors of the buzzer and of the main harnesses together and restore the rear quarter trim Rated Voltage DC 12 0V Operation Temp 20 C 70 C Storage Temp 30 C 80 C Reminder After installing the sensor system please confirm that the system functions properly Temporarily reconnect the negative cable to the battery to test Please also confirm that the original electronic devices work properly before re assembling the removed parts Then Restore cargo side trim LH rear scuff plate LH rear seat cushion rear trim luggage tray rear combination lamps and fasten all bolts and fasteners of the rear bumper Reconnect the negative cable to the battery Symptom When the gear is shifted to R the alert does not beep When the gear is shifted to R the alert beeps twice not once When the gear is shifted to R the alert beeps three times When the gear is shifted to R the alert beeps four times Function inspection Troubleshooting Possible Cause The buzzer plug has not been inserted Tail light power wire has not been spliced correctly The fuse to the ECU may have blown ECU is damaged One or more of the sensors is not connected properly One of the sensors may
7. t S rs pr ER TH h amp LS E j TREE e i amp us 4 A sS 1 u r as ar x u A eee is wees ar 4 bE Ae a es 4 he gt a a Pe d a 11 4 2 For the locations marked by in the Bern a picture cut the sticker into halves before I 12 18 Fix the sensor harnesses A to the bumper back side with stickers at the locations specified in red boxes in the picture For the locations marked by in in the picture cut the sticker into halves before applying it 19 Route Sensor harness B trough rear end panel grommet along with vehicle rear end harness 20 Remove the grommet for rear end harnesses and remove the taping around the neck Put Sensor harness B naked terminals into the tube from the ction shown in the picture i p Sensor Harness Fixation Point Remove vacant connector A that connected on Main Harness and insert terminals of Sensor Harness B Back view Check the codes are positioned Insert terminals according to EE SO el TUR the right hand chart epee Hy ae connectors are jointed 13 21 Disconnect the vacant male connector 6Pins that is connected on Main harness A Insert terminals of sensor harness B into te the 6 pin connector Check the wiring location by color as shown in below chart Tie sensor harness B near the rear end harness clamper B CAUTION Please make sure of the color matching o
8. t the speed of no more than 10 km h 3 You will hear beep sound when the vehicle starts to move backward Please put on the brake softly when the warning alert starts to beep continuously 4 Please turn down the radio when using this system so that the warning alert can be heard well 5 Please prevent the sensors from being knocked hard or washed by high pressure spray guns to avoid damage 6 Snow mud water drops or other substances on the sensors are likely to cause malfunction of the system Please always keep the sensor surface clean 7 Please note that there could be possible system failure under the following circumstances gt when the shape of an object to detect is pyramidal or acute gt when the system tries to detect an object which can easily absorb microwave e g fabric snow etc 8 Please note that there could be possible misdetection under the following circumstances gt when the vehicle moves on rugged gravel uphill and or bushed roads gt when the level of the back of the vehicle is lower due to overload gt when the system Is in the environment of 40KHz noise from metal or high pressure gas exhaust gt when other accessories are equipped inside the system s detection field 9 This system is suitable only for DC 12V vehicles Main X Before Installation Start and stop the engine to check if the power system functions properly such as door locks and the power ignition system When installing
9. though there is no object behind the vehicle The gear is in R and the warning goes off intermittently although there is no object behind the vehicle One of the sensors is damaged The objects are outside the range of detection ECU is damaged The sensor surface is covered with foreign materials such as mud water drops etc One of the sensors is damaged The sensors are not installed in the proper position The sensors have detected harsh roads The vehicles posture is weighted heavily to one side Confirm whether each sensor functions properly Refer to the service manual for the range of detection Confirm whether the ECU is damaged Confirm whether the sensor surface is covered with foreign materials Confirm whether each sensor functions properly Confirm whether the sensors are installed in the proper position Confirm the road condition Confirm the vehicles posture Replace any damaged sensor with a new one The warning does not go off when objects are outside the detection area Replace ECU witha new one Clean up the sensor surface and see if it functions normally Replace any damaged sensor with a new one Reinstall the sensors in the proper position Misdetection is possible when the system detects harsh roads or small objects on the road Misdetection may occur if the vehicle is heavily weighted in the rear or at the cusp of
10. to the horn wipers etc for battery proper operation If one tie wrap is too short use two con nected together Instructions for Car Parts Removal and System Necessary tools for installation General purpose tools power drills stabber 1 Remove the rear bumper fasteners 4 locations 2 Remove fasteners 5 locations inside both of the rear fenders The picture shows the right side IN UN EL III a ia a a an a E e aa EEEREN S WO i 3 Remove the bolts fixing the rear bumper and the tailgate stopper from both sides The picture shows the right side 4 Remove both of the rear combination lamps The picture shows the right side 5 Remove the luggage tray No tool required QW h gt me LY Q oD CC 2 S O K V the shown in the picture 10 15 Drill holes Important Use 24 drill hole saw for two OUTER SIDE holes Use 26 drill hole saw for two INNER SIDE holes 16 Installation of sensors 1 Insert the sensor into the te hole and locate tentatively Important Sensors with yellow connector Outer side Sensors with blue connector Inner side 2 Adjust set prong into the 3 hole that you have made in the previous procedure 3 Put the hook from the back side of connector and check the firm fixing 17 Install the sensors and sensor harnesses A as shown in the picture g
Download Pdf Manuals
Related Search