SL125, SL125-GPS & SL125-C Installation and Service Manual
Contents
1. Main Circuit Lantern Status Indicator LEDs STEADY LIGHT see Lantern Status Indicator LEDs A from above image LED Combinations Lantern Status Lantern Comment YELLOW LED RED LED Flashing ON OFF very quick 9 times Normal running condition in per second then 11 perme GEE daylight seconds off Flashing constant OFF Tee Battery is flat Battery must receive charge and light must see daylight for at least 1 minute before resuming normal operation i Battery is in state of very high ta ad voltage ON charge Check regulator if persists anneal Internal ambient temperature is Flashing Sate aa gt 75 C Selected light intensity is ON OFF 1 time dropped by 25 Will resume temperature per second gt 75 C normal operation when temperature lt 75 C Flashing ON OFF Low Battery Voltage lt 8v very quick 9 times per second Flashing ON OFF 9 times per second 9 Latest products and information available at www sealite com au PA Ey sealite FLASHING LIGHT Lantern Status Indicator LEDs A from image page 9 LED Combinations YELLOW LED Lantern Status Lantern Comment RED LED Normal running condition A Flashing Normal and synchronised to GPS Will take up to sine one le when 10 minutes when first powered up Condition only active in darkness Normal running condition but light does not synchronise to other lights GPS not fitted or no2. W PAT rl Sealite Maintenance and Servicing Designed to be virtually maintenance free the SL125 SL125 C amp SL125 GPS require minimal attention though the following maintenance and servicing information is provided to help ensure the life of your Sealite product 1 Cleaning Lens occasional cleaning of the light lens may be required Using a cloth and warm soapy water wipe off any foreign matter before rinsing the lens with fresh water Cleaning Solar Panels occasional cleaning of the solar panels may be required Using a cloth and warm soapy water wipe off any foreign matter before rinsing the panels with fresh water SL125 C models only Battery Check inspection of batteries should be performed every three years minimum to ensure that the charger battery and ancillary electronics are functioning correctly Using a voltage meter check that the battery voltage is at least 12 volts under 100MA load and ensure all terminals are clear of foreign matter SL125 C models only Replacing the Battery The SL125 C lanterns have a sealed battery compartment which provides the user with the ability to change the battery after years of operation 1 Remove the bolt lock securing the battery box lid and open unit 2 Inside the battery box is an internal battery container To access the battery remove the four 3 8 9 10 11 screws and lid of this internal container Remove old battery from container
3. 1 The warranty is applicable to lanterns manufactured from 1 1 2000 2 The lantern must be installed in accordance with Sealite instructions 3 No modifications to the original specifications determined by Sealite shall be made without written approval of Sealite Pty Ltd 4 Input voltage shall not exceed those recommended for the product 5 Warranty does not cover damage caused by the incorrect replacement of battery in the SL15 SL60 or SL70 lantern models Replacement of battery is excluded from the warranty No recognition shall be given to flooding or damage incurred from misuse of lanterns solar modules are covered by individual manufacturers warranty eS Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor Sealite products are subject to certain Australian and world wide patent applications Head Office USA Customers Sealite Pty Ltd GulfRim Navigation 11 Industrial Drive 1401 South State Somerville Vic 3912 Abbeville LA 70510 Australia USA Tel 61 3 5977 6128 Ph 877 893 0789 Fax 61 3 5977 6124 Fax 337 893 6256 Email info sealite com au Internet www gulfrim com Internet www sealite com au Email info gulfrim com 20 Latest products and information available at www sealite com au
4. 6 LFL 10 S means 6 very quick flashes followed by a long flash during a 10 second interval The amount of power your lantern draws through the night depends on the duty cycle i e the amount of time on as a proportion to the timing cycle For example 0 5 seconds on and 4 5 seconds off equals a 10 duty cycle lt is best to operate at the lowest duty cycle appropriate to the actual needs of the application Please note Sealite models will retain full autonomy in normal operating conditions with duty cycles up to approximately 30 In applications whereby duty cycles exceed this limit a reduction in lantern intensity is recommended Please contact a Sealite consultant if assistance is required Recommended Rhythm for Flashing Light IALA Regions A and B RHYTHM Any other than Composite Group Flashing 2 1 Composite Group Flashing 2 1 Preferred Channel Port Composite Group Flashing 2 1 Very quick or quick Very quick 3 every 5 seconds or quick 3 every 10 seconds 3 South Cardinal Mark Very quick 6 long flash every 10 seconds or quick 6 long flash every 15 seconds West Cardinal Mark Very quick 9 every 10 seconds or quick 9 every 15 seconds Isolated Danger Mark Group flashing 2 Safe Water Mark Isophase occulting one long flash every 10 seconds or Morse Code A Special Marks Any other than those described for Cardinal Isolated Danger or Safe Water Marks 12 Latest products and informati
5. 0 0 3 0 3 0 8 0 7 0 6 0 3 OFF 0 3 0 3 0 8 0 7 0 6 ON 1 0 2 0 2 4 0 3 0 4 0 5 1 5 1 0 2 0 0 6 0 7 0 7 0 5 0 2 0 3 0 2 0 3 0 6 0 3 ON 0 2 0 3 0 2 0 3 0 6 0 7 0 3 0 7 0 3 1 5 0 5 0 5 0 5 1 2 0 8 1 0 1 0 0 3 0 3 0 8 0 7 0 6 0 3 OFF 0 3 0 3 0 8 0 7 0 6 OFF 4 5 3 0 0 0 7 0 1 1 0 6 7 6 5 5 11 0 0 0 0 0 3 5 7 5 0 2 0 3 0 2 0 3 0 6 0 3 ON 0 2 0 3 0 2 0 3 0 6 ON 0 9 1 2 1 5 1 0 1 4 1 9 2 1 0 5 18 Latest products and information available at www sealite com au OFF ON OFF 0 7 0 3 2 7 0 7 0 3 5 7 15 0 5 3 5 05 0 5 15 5 1 2 0 8 11 2 1 0 1 0 11 0 OFF ON OFF 0 7 0 3 0 7 0 7 0 3 0 7 1 0 0 5 1 0 1 0 0 5 1 0 OFF ON OFF 03 02 03 03 03 0 3 08 02 0 8 0 7 0 3 0 7 06 06 0 6 03 03 0 3 OFF ON OFF 03 02 0 3 03 03 0 3 08 02 08 0 7 03 0 7 06 06 0 6 OFF ON 7 1 6 8 6 5 1 0 11 8 10 7 10 1 0 5 0 5 0 2 0 3 0 2 0 3 0 6 0 3 0 2 0 3 0 2 0 3 0 6 OFF 10 5 0 3 0 3 0 8 0 7 0 6 0 3 0 3 0 3 0 8 0 7 0 6 2 0 2 0 2 0 2 0 2 0 2 0 0 2 0 3 0 2 0 3 0 6 5 0 4 4 7 0 7 0 5 8 9 4 0 3 0 3 0 8 0 7 0 6 0 2 0 3 0 2 0 3 0 6 0 3 0 3 0 8 0 7 0 6 0 2 0 3 0 2 0 3 0 6 5 8 4 9 6 8 6 7 4 8 LP hae sealite Trouble Shooting Problem Remedy Lantern will not activate e Ensure lantern is in darkness e Wait at least 60 seco
6. 20 50 8 A FL 2 8S 04 10 04 62 4 7 FL 2 8S 05 10 05 60 8 8 FL 2 8S 08 12 24 36 5 7 FL 2 8S 10 10 10 5 0 4 C oc 2 8s 30 20 10 20 5 C oc 2 8s 50 10 10 10 F B va 2 8s 02 10 02 66 9 A FL 2 10S 04 16 04 76 9 8 FL 2 10S 05 05 15 75 6 7 FL 2 10S 05 10 05 80 7 7 FL 2 10 S 05 15 05 75 6 9 FL 2 10S 05 20 05 7 0 8 7 FL 2 10 S 08 12 08 72 B 9 FL 2 10S 10 10 10 70 9 7 FL 2 10 S 10 15 10 65 4 9 Q 2 10S 06 04 06 84 B A FL 2 12S 04 10 04 10 2 C 9 FL 2 12S 05 10 05 10 0 D 9 FL 2 12S 15 20 15 70 A 8 FL 2 15S 05 15 220 110 A 7 FL 2 15S 10 20 10 11 0 8 B Q 2 15S 02 08 02 13 8 C A FL 2 20S 10 30 10 15 0 D A FL 2 25S 10 10 1 0 22 0 15 Latest products and information available at www sealite com au 7 W Sealite SWITCH FLASH CODE ON OFF ON OFF ON OFF A B 7 9 Q 3 5S 05 05 05 05 05 25 5 9 Va 3 5S 02 03 02 03 02 38 0 cC vVva 3 5S 03 02 03 02 03 37 E 9 Va 3 5S 03 03 03 03 03 35 3 C FL 3 6S 05 10 05 10 05 25 2 B FL 2 1 6S 03 04 03 12 03 35 A B Q 3 6S 03 07 03 07 03 37 F A FL 3 8S 05 10 05 10 05 45 0 B FL 3 9S 03 10 03 10 03 6 1 B 7 FL 3 9S 08 12 08 12 08 42 B 8 FL 3 10 S 03 07 03 07 09 741 C 8 FL 3 10 S 04 o6 04 06 12 68 C B FL 3 10S 0 5 05 05 05 05 75 C 7 FL 3 10 S 0 5 15 05 15 05 55 D B FL 3 10S 06 o6 06 06 06 70 D 7 FL 3 10 S 10 10 10 10 10 50 3 8 FL 2 1 10S 05 07 05 241 05 5 7 8 9 OC 3 10S 50 10 10 10 10 10 B B Q 3 10S 03 07 03 07 03 77 D 8 FL 2 1 10S 05 05 05 05 15 65 1 B FL 3 12S 0 5 15 0
7. 4 0 6 4 OC 6S 4 0 2 0 3 3 OC6S 4 5 1 5 4 3 OC6S 5 0 1 0 A 4 FL7S 1 0 6 0 9 6 FL7S 2 0 5 0 5 6 OC 7S 4 5 2 5 D 5 FL 7 5 S 0 5 7 0 C 1 FL 7 5 S 0 8 6 7 E 5 FL8S 0 5 7 5 B 4 FL8S 1 0 7 0 6 2 ISO 8 S 4 0 4 0 A 2 LFL 8 S 2 0 6 0 6 6 OC8S 5 0 3 0 B 2 LFL 8 S 3 0 5 0 F 5 FL9S 0 9 8 1 C 4 FL9S 1 0 8 0 7 6 OC9S 6 0 3 0 0 6 FL 10S 0 2 9 8 1 6 FL 10S 0 3 9 7 D 1 FL 10S 0 5 9 5 2 6 FL 10S 0 8 9 2 E 1 FL 10S 1 0 9 0 1 4 FL 10S 1 5 8 5 C 2 LFL 10 S 2 0 8 0 D 2 LFL 10 S 3 0 7 0 7 2 ISO 10 S 5 0 5 0 2 4 LFL 10 S 4 0 6 0 8 6 OC 10 S 6 0 4 0 5 3 OC 10 S 7 0 3 0 6 3 OC 10S 7 5 2 5 F 1 FL 12S 1 2 10 8 D 4 FL 12S 2 5 9 5 3 4 LFL 12 S 2 0 10 0 0 2 FL 15S 1 0 14 0 4 4 LFL 15 S 4 0 11 0 7 4 OC 15S 10 0 5 0 A 6 LFL 20 S 2 0 18 0 E 4 FL 26 S 1 0 25 0 14 Latest products and information available at www sealite com au 7 W Sealite SWITCH FLASH CODE ON OFF ON OFF A B 0 A FL 2 4S 05 10 05 20 E B va 2 4s 02 10 02 26 1 A FL 2 4 5S 03 10 03 29 2 A FL 2 4 5S 04 10 04 27 3 A FL 2 4 5S 05 10 05 25 F 9 FL 2 5S 02 08 02 38 2 C FL 2 5S 02 12 02 34 4 A FL 2 5S 04 06 04 36 0 7 FL 2 5S 05 10 05 3 0 1 7 FL 2 5S 10 10 10 20 9 B aQ 2 5S 03 07 03 37 2 9 Q 2 5S 05 05 05 35 5 A FL 2 5 5S 04 14 04 33 7 8 FL 2 6S 03 06 10 41 A A FL 2 6S 03 09 03 45 6 A FL 2 6S 03 10 03 44 7 A FL 2 6S 04 10 04 42 9 9 FL 2 6S 05 10 05 40 2 8 FL 2 6S 08 12 08 32 3 7 FL 2 6S 10 10 10 3 0 3 9 Q 2 6S 03 07 03 47 A 9 FL 2 7S 10 10 10 40 7 B FL 2 8S 04 06
8. and disconnect all connecting wires Discard battery in a safe manner Connect the Battery Negative wire to the negative terminal of the new battery and the Battery Positive wire to the positive terminal of the new battery Connect the Solar Negative wire to the negative terminal of the battery and the Solar Positive wire to the positive terminal of the battery Replace the internal battery container lid and screws making sure no wires are protruding Close the battery box lid and secure with bolt lock Light is now activated 12 To test place dark cover towel or jacket on top of light to activate sensor light will come on Care must be taken to observe the polarity of each wire before they are connected To ensure waterproofing of the unit make sure that no wires are protruding and that there is an even seal Always discard old batteries in a safe manner 11 Latest products and information available at www sealite com au Lf ad Sealite Flash Codes SEALITE code reference is listed by number of flashes For the latest version of this document check http www sealite com au E mail info sealite com au symbols FL Flash followed by number Eg FL 1 S one flash every second F Fixed Q Quick flash VQ Very quick flash OC Occulting greater period on than off ISO Isophase equal period on and off LFL Long flash long MO Morse code contains letter For example VQ
9. for the SL125 allowing the performance of the units to be monitored from remote sites System status includes battery condition flash characters operational configuration and lantern buoy position Specifications Power Amp hour Intensity peak No LEDs Colour Voltage SL125 1 R SL125 1 G SL125 1 W SL125 1 Y SL125 2 R SL125 2 G SL125 2 W SL125 2 Y SL125 3 R SL125 3 G SL125 3 W SL125 3 Y SL125 4 R SL125 4 G SL125 4 W SL125 4 Y Red Green White Yellow 1 tier LED Lantern 2 tier LED Lantern Red Green White Yellow 3 tier LED Lantern 4 tier LED Lantern Specifications subject to change or variation without notice All SL125 models outlined above are available as a complete lantern assembly Incorporating 1 or 2 20watt solar modules as standard Sealite ss SL125 C provides a complete solution for visual navigation requirements These models can also be readily equipped with up to 2 individual 40watt solar modules to power longer range requirements or ancillary equipment 4 Latest products and information available at www sealite com au SL125 standard Diam 17mm x 30mm Slot Nylon Cable Gland Diam 16mm Sealed Vent 9 09 SL125 2 amp SL125 3 SL125 4 0 67 x 1 18 6 places Flash Adjustment 7 82 KI D Nylon Cable Gland olin Nylon Cable Gland CCC olin Diam 16mm ala Diam 16mm A DANY A bs vai i i Eza l i Cae en en a Ee EE
10. 0S 15 15 15 15 15 15 15 95 0 F Q 4 20S 05 05 05 05 05 05 05 165 E E Q 4 28S 05 05 05 05 05 05 05 245 6 F FL 4 30 S 05 05 05 05 05 05 05 265 17 Latest products and information available at www sealite com au 7 W Sealite SWITCH o ooummo Dd manood Y SWITCH gt ND gt TD maino y SWITCH OWNNN OS TM M M71MMo SWITCH O U 8B mmmnmummy SWITCH A B FLASH CODE Q 5 7S Q 5 10S FL 5 16 5 S FL 5 20S FL 5 20S FL 5 20 S FLASH CODE Q 6 10S FL 6 15S FL 6 15S FL 6 LFL 15 S FLASH CODE VQ 6 LFL 10 S VQ 6 LFL 10 S Q 6 LFL 15 S Q 6 LFL 15 S Q 6 LFL 15 S VQ 6 LFL 15 S FLASH CODE VQ 9 10 S VQ 9 10 S Q 9 15S Q 9 15S Q 9 15S FLASH CODE 0 3 0 3 5 0 0 5 0 8 1 0 0 3 0 3 0 5 0 2 0 3 0 2 0 3 0 6 0 3 ON 0 2 0 3 0 2 0 3 0 6 O 0 7 0 3 0 7 0 3 1 5 0 5 0 5 0 5 1 2 0 8 1 0 1 0 0 3 0 3 0 8 0 7 0 6 0 3 OFF 0 3 0 3 0 8 0 7 0 6 N MORSE CODE INDICATES LETTER N32 OT DMOOODODWONN 0N 0 DDH OOO OO WO MO A 6S MO A 8 S MO A 8 S MO U 10 S MO U 10 S MO U 10 S MO A 10S MO D 10S MO A 15S MO U 15 S MO U 15 S MO U 15 S MO B 15 S 0 2 0 3 0 2 0 3 0 6 0 3 ON 0 2 0 3 0 2 0 3 0 6 OFF 0 3 0 6 0 4 0 6 0 8 1 2 0 3 0 7 0 4 0 6 0 5 0 5 0 5 0 5 5 0 1 0 0 5 1 5 0 6 0 3 0 7 0 5 0 7 0 7 1 5 0 5 0 7 0 3 0 7 0 3 1 5 0 5 0 5 0 5 1 2 0 8 1 0 1
11. 5 5 www sealite com au A Quality Endorsed Company ISO9001 2000 Lic 14834 SAI Global Ltd SL125 SL125 GPS amp SL125 C installation and Service Manual Version 3 1 Sealite Table of Contents Liisi Spena Pe ics a T SL125 amp SL125 C Models 4 Daana mems o Mainerance a Servicing n peros o Toeto o Sealite Lantern Warranty Introduction Congratulations By choosing to purchase a Sealite lantern you have become the owner of one of the most advanced LED marine lanterns in the world Sealite Pty Ltd has been manufacturing lanterns for over 20 years and particular care has been taken to ensure your lantern gives years of service As a commitment to producing the highest quality products for our customers Sealite has been independently certified as complying with the requirements of ISO 9001 2000 quality management system Sealite lanterns comply with requirements of the US Coast Guard in 33 CFR part 66 for Private Aids To Navigation By taking a few moments to browse through this booklet you will become familiar with the versatility of your lantern and be able to maximise its operating function Please remember to complete the Sealite warranty registration card accompanying your lantern 2 Latest products and information available at www sealite com au 7 W Sealite Operating Principle The solar module of the lantern converts sunlight to an electrical current that is used t
12. 5 pulse will reduce the power consumption to 25 of the normal 100 setting and the range by 50 This setting may be used to adjust to local sunlight conditions The following diagrams indicate pulse settings 25 Selecting a Flash Code Rotary Switches A and B All lanterns have 2 rotary switches marked A and B on the flasher unit as below Turning the small arrows to the appropriate number or letter will set the code see Flash Code section page 12 The unit may take up to one minute to activate a new flash code A comprehensive list of available flash codes is listed on pages 12 19 of this manual Rotary Switches A and B PCB Pin lL PCB Pin lL NOTE Refer to Lantern Status section to check the status of the light after activated Indicated by red and yellow status LED s viewed at the base of the lens page 9 7 Latest products and information available at www sealite com au 7 W Sealite GPS Option This GPS option can be added to any of the SL125 models previously outlined and provides the user with the ability to mark a channel port or river with independently operating lanterns that all flash in synchronisation This improves the effectiveness of marker lights by highlighting the channel port or river outline each time all the synchronised lights turn on No additional power supplies aerials or control systems are required and with its microprocessor based system the
13. 5 15 05 75 E A FL 3 12S 05 20 05 20 05 65 E 7 FL 3 12S 08 12 08 12 08 72 B 6 FL 3 12S 10 10 10 30 10 50 4 8 FL 2 1 12S 08 12 08 24 08 60 5 8 FL 2 1 12S 10 10 10 40 10 40 1 8 FL 2 1 13 5S 10 10 10 40 10 55 F 7 FL 3 15S 03 17 03 17 03 107 9 D FL 3 15S 04 10 04 10 04 118 0 8 FL 3 15S 0 5 15 05 15 05 10 5 F 8 FL 2 1 15S 06 03 06 03 14 118 0 9 FL 2 1 15S 0 7 05 07 05 19 10 7 1 9 FL 2 1 15S 0 7 07 07 07 24 10 1 6 8 FL 2 1 15S 10 20 10 50 10 50 1 C vVQ 3 15S 0 1 05 01 05 01 137 4 B FL 3 20S 05 30 05 30 05 125 3 B FL 3 20S 05 15 05 15 05 155 5 B FL 3 20S 08 12 08 12 08 152 6 B FL 3 20S 10 10 10 10 10 150 16 Latest products and information available at www sealite com au SWITCH FLASH CODE ON OFF ON OFF ON OFF ON OFF A B B F Va 4 4S 0 25 0 25 0 25 0 25 0 25 0 25 0 25 2 25 B D a 4 s 03 07 03 07 03 07 03 27 8 D a4 s 04 o6 04 06 04 06 04 26 1 D FL 4 10S 05 10 05 10 05 10 05 50 2 D FL 4 10S 08 12 08 12 08 12 08 32 F E Q 410S 03 07 03 07 03 07 03 67 B E FL 4 12S 03 17 03 17 03 17 03 57 4 F FL 4 12S 05 05 05 05 05 05 05 85 C E FL 12S 05 15 05 15 05 15 05 55 3 D FL 4 12S 08 12 08 12 08 12 08 5 2 A D Q 412S 03 07 03 07 03 07 03 87 4 D FL 4 15S 05 15 05 15 05 15 05 85 8 E FL 4 15S 10 10 10 10 10 10 10 80 7 D FL 415S 15 05 05 05 05 05 05 105 D E FL 4 16S 05 15 05 15 05 15 05 95 C D FL 4 20S 03 30 03 30 03 30 03 98 5 D FL 4 20S 05 15 05 15 05 15 05 13 5 0 D FL 4 20S 05 15 05 15 05 45 05 105 3 F FL 4 2
14. SL125 GPS option is specifically designed to provide maximum reliability and performance over a wide range of environmental conditions The GPS board is a separate PCB mounted above the standard SL125 circuitry Operating Principle Each light operates independently and requires no operator intervention A minimum of 3 satellites need to be in view for the built in GPS receiver to collect time data At dusk the light sensor will turn the light on If time data is available the light will come on synchronised to every other light with the same selected flash code Synchronisation is achieved using an internal algorithm based on the highly accurate time base and time data received from the satellites The satellite data is provided from a number of earth stations using atomic clocks as the time base Continuous self checking ensures that the light will continue to run in synchronisation Light Activation At power up the microprocessor checks that the internal GPS module is programmed correctly and is able to provide valid time base and time data The light then checks for day night If it is daylight the internal microprocessor will go to idle mode after approximately 10 seconds This reduces the overall power consumption when the light is not required Once outside with a clear view of the sky valid data should become available within 20 minutes Daylight Operation During daylight hours the microprocessor is in idle mode to reduce power con
15. gative wires to 12volt power supply ONLY 2 To test place dark cover towel or jacket on top of light to activate sensor light will come on 3 Ensure that the unit is bolted to an even flat surface SL125 C 1 Inside the battery box is an internal battery container To access the battery remove the four screws and lid of this internal container 2 Connect the Battery Negative wire to the negative terminal of the battery and the Battery Positive wire to the positive terminal of the battery 3 Connect the Solar Negative wire to the negative terminal of the battery and the Solar Positive wire to the positive terminal of the battery 4 Replace the internal battery container lid and screws making sure no wires are protruding 5 Close the battery box lid and secure with bolt lock Light is now activated 6 To test place dark cover towel or jacket on top of light to activate sensor light will come on 7 Ensure that the unit is bolted to an even flat surface Care must be taken to observe the polarity of each wire before they are connected 6 Latest products and information available at www sealite com au peT Ll W Sealite Selecting an Intensity Setting Pulse settings on Sealite lanterns operate via DIP switches located near the rotary switches on the flasher unit The pulse settings may be used to reduce the power consumption and intensity of the lantern Setting the lantern to 2
16. las AH A PLI 231 231 9 09 9 09 Diam 17mm x 30mm Slot Diam 1 7mm x 30mm Slot 0 67 x 1 18 6 places 0 67 x 118 6 places Flash Adjustment Flash Adjustment Sealed Vent Sealed Vent 5 Latest products and information available at www sealite com au et Peg ey es F r L j sealite SL125 C r DIAM 13 5mm 10 53 on PCD 200mm 17 87 f OSA kT ki 4 4 a Y g W AYE af N TSD NE Installation of SL125 amp SL125 C Models Before activating the light intensity and flash settings must be set 1 Remove the bolt lock securing the battery box lid and open unit SL125 C ONLY 2 Remove the bung from the base of the SL125 light 3 The power and range settings of the lantern are adjusted by setting the DIP switches inside the lantern Your lantern is normally set to maximum range see Selecting Intensity Setting page 7 4 Set rotary switches to the required flash code see Selecting a Flash Code page 7 5 Replace bung 6 A sealed vent on the base allows air transfer without moisture intake and should not be disturbed Lantern is activated by connecting positive and negative battery wires and solar module wires for SL125 C SL125 1 Battery Connection Connect Battery Positive wire to positive terminal of battery and Battery Negative wire to negative terminal of battery Mains Connection Connect positive and ne
17. nds for the program to Initialise in darkness e Ensure switch setting is on a valid code not unused flash code e Ensure battery terminals are properly connected e Ensure battery voltage is above 12volts Lantern will not operate for the e Expose lantern to direct sunlight and monitor operation for entire night several days Sealite products typically require 1 5 hours of direct sunlight per day to retain full autonomy From a discharged state the lantern may require several days of operational conditions to cycle up to full autonomy e Reducing the light output intensity or duty cycle flash code will reduce current draw on the battery e Ensure solar module is clean and not covered by shading during the day 19 Latest products and information available at www sealite com au Sealite Lantern Warranty Activating the warranty Upon purchase the Sealite warranty must be activated for recognition of future claims To do this you have two 2 options 1 Postal registration Please complete the Sealite Warranty Registration card and return to Sealite within 30 days of your purchase 2 Online registration Please complete the Online Registration form at www sealite com au or www sealiteusa com Sealite Pty Ltd will repair or replace your lantern in the event of electronic failure for a period of three years from the date of purchase The unit must be returned to Sealite Pty Ltd freight prepaid Warranty Conditions
18. o charge the battery SL125 C models only The battery provides power to operate the lantern at night The flasher unit has very low current requirements A microprocessor drives an array of ultra bright LED s through a DC DC converter which enables the LED s to operate within the manufacturer s specifications The battery is protected from over charging within the circuit to ensure maximum battery life On darkness the microprocessor will initiate a program check and after approximately 1 minute begin flashing to the set code Technology Electronics Sealite employs leading in house electronic engineers in the design and development of software and related circuitry All individual electronic components are sourced directly by Sealite procurement staff ensuring that only the highest quality components are used in our products LED Technology All marine lanterns use the latest advancements in LED Light Emitting Diode technology as a light source The major advantage of LED s over traditional light sources is well established in that they typically have an operational life in excess of 100 000 hours resulting in substantial savings to maintenance and servicing costs Precision Construction Commitment to investing in the design and construction of injection moulded parts including optic lenses light bases and a range of other components ensures that all Sealite products are of a consistent and superior quality Optical Perfo
19. on available at www sealite com au SWITCH FLASH CODE ON OFF A B 0 0 F Steady light D 3 VQ0 5S 0 2 0 3 E 3 VQ 0 6 S 0 2 0 4 F 3 VQ 0 6 S 0 3 0 3 7 3 Q1S 0 2 0 8 8 3 Q1S 0 3 0 7 9 3 Q1S 0 4 0 6 A 3 Q1S 0 5 0 5 8 4 Q1S 0 8 0 2 B 3 Q1 2S 0 3 0 9 9 4 Q1 2S 0 5 0 7 C 3 Q1 2S 0 6 0 6 F 4 FL1 5S 0 2 1 3 1 0 FL1 5 S 0 3 1 2 0 5 FL1 5S 0 4 1 1 0 4 FL1 5 S 0 5 1 0 2 0 FL2S 0 2 1 8 3 0 FL2S 0 3 1 7 4 0 FL2S 0 4 1 6 5 0 FL2S 0 5 1 5 6 0 FL2S 0 7 1 3 7 0 FL2S 0 8 1 2 1 2 ISO 2S 1 0 1 0 8 0 FL 2 5 S 0 3 2 2 9 0 FL 2 5 S 0 5 2 0 D 6 FL 2 5 S 1 0 1 5 1 5 FL3S 0 2 2 8 A 0 FL3S 0 3 2 7 2 5 FL3S 0 4 2 6 B 0 FL3S 0 5 2 5 3 5 FL3S 0 6 2 4 C 0 FL3S 0 7 2 3 D 0 FL3S 1 0 2 0 2 2 ISO 3S 1 5 1 5 5 4 Oc 3S 2 0 1 0 E 2 Oc 3S 2 5 0 5 4 6 OC 3 5 S 2 5 1 0 4 5 FL4S 0 2 3 8 5 5 FL4S 0 3 3 7 E 0 FL4S 0 4 3 6 F 0 FL4S 0 5 3 5 6 5 FL4S 0 6 3 4 0 1 FL4S 0 8 3 2 1 1 FL4S 1 0 3 0 2 1 FL4S 1 5 2 5 3 2 ISO 4S 2 0 2 0 3 6 OC 4S 2 5 1 5 F 2 OC 4S 3 0 1 0 3 1 FL 4 3 S 1 3 3 0 8 5 FL5S 0 2 4 8 4 1 FL5 S 0 3 4 7 5 1 FL5 S 0 5 4 5 9 5 FL5 S 0 9 4 1 6 1 FL5 S 1 0 4 0 7 1 FL5S 1 5 3 5 4 2 ISO5S 2 5 2 5 8 2 LFL5S S 2 0 3 0 0 3 Oc5S 3 0 2 0 13 Latest products and information available at www sealite com au SWITCH FLASH CODE ON OFF A B 1 3 OC5S 4 0 1 0 2 3 OC5S 4 5 0 5 C 6 FL6S 0 2 5 8 B 5 FL6S 0 3 5 7 C 5 FL6S 0 4 5 6 8 1 FL6S 0 5 5 5 9 1 FL6S 0 6 5 4 A 1 FL6S 1 0 5 0 7 5 FL6S 1 2 4 8 B 1 FL6S 1 5 4 5 5 2 ISO 6 S 3 0 3 0 9 2 LFL 6 S 2 0
20. rmance sealite manufactures a range of marine LED lenses moulded from multi cavity dies Complex shapes such as the SL70 lens are a testament to the company s superior in house lens manufacturing Capabilities and outstanding optical performance Award winning Patented Technology several United States and Australian patent registrations are held on Sealite s range of innovative designs with other regional patents pending in Canada United Kingdom and Europe 3 Latest products and information available at www sealite com au Lf ad Sealite SL125 amp SL125 C Models The SL125 5 7nm light fixture is the most advanced LED marine lantern on the market Utilising the latest software and micro circuitry developments the lantern boasts a huge number of features including flash memory and the most efficient power conversion available This maintenance free model is also available with up to 4 tiers of 36 LEDs to increase the light intensity for a range of different light colours see Specifications table below Each LED tier utilises the Sealite omni directional LED Reflector US Pat No 6 667 582 AU Pat No 778 918 to increase the intensity and uniformity of the horizontal output In particular the SL125 4 tier model utilises a unique heat dissipating domed lens to achieve maximum LED intensity output over a wider range of environmental conditions see diagram page 5 Remote monitoring and control capabilities are also available
21. sumption Time data continues to be updated once per second The microprocessor will automatically exit the idle mode as soon as dark conditions are detected Dark Operation When dark conditions are detected the light Checks for valid time data and is turned on after a delay based on the current time and the length of the selected flash code If valid time data is not detected the light will turn on after approximately 10 seconds This light will not be synchronised Ifthe light turns on unsynchronised it will continually check for valid time data Once valid data is found the light will automatically synchronise NOTE Lights will not synchronise if different flash codes are selected 8 Latest products and information available at www sealite com au LP hae Sealite Lantern Status Two status LED s on the main printed circuit board position A in image below provide the operator with an indication of the lantern status There is one RED and one YELLOW LED that in different combinations of ON OFF FLASHING will indicate the current operational status of the light and vary depending on whether the lantern is set to steady on or a flashing light GPS Status Indicator LEDs characteristic These indicator LED s Ges fine can be viewed at the where fitted base of the lens Separate indicator LEDs are located on the top of the GPS circuit board where fitted see position B amp C of image below
22. time data received B Flashing ON OFF very quick constant Normal but not synchronised C Flashing ON OFF very quick 9 times Normal OFF Normal running condition in daylight second then 11 seconds off Battery is flat Battery must receiver Pica eae Low Battery charge and light must see daylight ria Oe i nd Voltage lt 8v for at least 1 minute before resuming Imes per seco normal a Internal ambient temperature is gt 75 C Selected light intensity is dropped by 25 Will resume normal operation when temperature lt 5C High internal ambient temperature gt 75 C Flashing ON OFF Flashing 1 time per ON OFF 1 time second per second NOTE 1 1 second interval flashing Yellow LED indicates light is operating in synchronisation with the optional fitted GPS correctly 2 If checking in daylight lantern must be covered to activate flash pattern GPS BOARD where fitted LED Combinations Lantern Comment YELLOW LED RED LED GPS Status Indicator LEDs B see image page 9 A ON steady OFF fNormal ON or OFF GPS powered up GPS Status Indicator LEDs C see image page 9 B Flashing Flashing OM OEE KEEN om ie very Normal ON GPS software running quick quick constant constant faint C Flashes in Flashes in sequence with sequence with Off OFF ON GPS software not operational red LED yellow LED 10 Latest products and information available at www sealite com au Ay a
Download Pdf Manuals
Related Search