EN-US - Getinge Infection Control
Contents
1. BARRIER WALL THICKNESS EXCEED 5 1 4 SEE NOTE 11 Z SERVICE CLEARANCE OF 18 Me a IS SHOWN ON BOTH SIDES THIS 5 THE SPACE REQUIREMENT TO GET THE WASHER S INSTALLED AND FOR SERVICE ACCESS CART APPROACH AREA 762 BOTH ENDS 8 WASHER DISINFECTO UTILITY CONNECTION LOCATIONS f an t Da 2 515 UNIT DEPTH 2 4 33 2 5 He B95 349 6 5 6 19601 6 156 1870 UNIT HEIGHT 47 09067 or ye 1240 hie 1 2946 370 GETINGE 88 SERIES TECHNICAL DATA NOTICE WORK BY OTHERS SAFE AND EFFICIENT OPERATION OF THIS PRODUCT IS DEPENDANT UPON THE OWNER USER PROVIDING THE SERVICES SPECIFIED HEREIN AS WELL AS ANY OTHER NORMALLY ACCEPTED ELECTRICAL MECHANICAL OR PLUMBING INTERFACE BETWEEN USERS SUPPLY AND THIS PRODUCT GETINGE INC WILL NOT ASSUME RESPONSIBILITY FOR PROBLEMS THAT RESULT FROM NONCOMPLIANCE WITH THE INDICATED CONDITIONS THE FOLLOWING CONDITIONS AND SERVICES ARE REQUIRED FOR THIS EQUIPMENT AND ARE BE PROVIDED BY OTHERS IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO COMPLETE ALL ELECTRICAL CONNECTIONS USING PROPERLY SIZED WIRING IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE AND ALL APPLICABLE LOCAL CODES SEE THE GETINGE INSTALLATION MANUAL FOR SPECIFIC INSTRUCTIONS WATER AND STEAM LINE SHUTOFF VALVES AND ELECTRICAL DISCONNECT SWITCH ES MUST BE PROVIDED AT EACH WASHER ON UNIT SERVICES PRESSURE TE2. GETINGE GROUP is a leading global provider of equipment and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences We operate under the three brands of ArjoHuntleigh GETINGE and MAQUET ArjoHuntleigh focuses on patient handling and hygiene disinfection DVT prevention medical beds therapeutic surfaces and diagnostics GETINGE provides solutions for infection control within Healthcare and contamination prevention within Life Sciences MAQUET specializes in therapeutic applications products solutions and services for OR and ICU 0001 Product specification Edition D 2008 09 11 jt HC_WSDS_PS_88Turbo_0710_EN_US 507
3. BLE IN THE US GETINGE 88 SERIES TECHNICAL DATA OPERATING CONDITIONS ROOM TEMPERATURE lt 41 104 5 40 AIR HUMIDITY 80 AT 87 F 31 RADIANT HEAT LOSS 5123 BTU HR 1500W 194 F 90 ON SOILED AND CLEAN SIDE HEAT TO EXHAUST MAX 20491 BTU HR 6000W DURING DRYING MAX SURFACE 125 50 TEMPERATURE NOISE LEVEL 60 69 dBA WEIGHTS AND DIMENSIONS WIDTH 50 1270mm DEPTH 39 990mm HEIGHT 73 5 8 1870mm MATERIAL OF CONSTRUCTION STAINLESS STEEL AISI 304 FINISH 0 45 0 7 EFFECTIVE CHAMBER DIMENSIONS WIDTH 26 3 16 665mm DEPTH 31 1 2 800mm HEIGHT 26 1 4 667mm MATERIAL OF CONSTRUCTION STAINLESS STEEL EN 1 4404 ASTM 316 1 FINISH RA 0 04 WEIGHT AND FLOOR LOADING TOTAL WEIGHT 1764 LBS 800 KG LOADING PER FOOT 441 LBS 200 KG 4 FEET IN TOTAL SPECIFIC FLOOR LOADING 0 899 PSI 6 2 kN m 1 2 3 5 6 7 9 10 11 12 13 14 15 10 NOTES ARCHITECTS AND CONTRACTORS IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO INSURE BY USE OF PRESSURE REGULATORS OR OTHER MEANS THAT MAXIMUM SPECIFIED PRESSURES ARE NOT EXCEEDED DYNAMIC PRESSURE IS MEASURED DURING FLOW CONDITIONS STATIC PRESSURE SHALL NOT EXCEED 60 PSIG 400kPA FOR SERVICE CONDITION PRESSURE BE MEASURED AT POINT OF CONNECTION TO THE WASHER A SEPARATE SUPPLY PUMP MUST BE USED IF PRESSURE OF PURIFIED RINSE IS BELOW 8 PSIG SOkPA
4. CUSTOMER REFERENCE GETINGE 88 SERIES WASHER DISINFECTORS PRODUCT SPECIFICATION PRODUCT The Getinge 88 Series GETINGE 88 TURBO is a fully automatic microprocessor controlled Washer Disinfector WD The washer has a capacity of 15 DIN trays with short process time including drying Processing cycles are factory programmed with recom manded treatment parameters for pre rinsing cleaning post rinsing thermal disinfection final rinsing and drying Validated programs are secured by access code Deter gents and rinse agents are automatically dispensed during cycle The Getinge 88 Series washer is standard as double door model with automatically operated doors INTENDED USE The Getinge 88 Series are Washer Disinfectors for washing intermediate level disinfection and drying of surgical instru ments rigid and tubular hollow ware wash bowls contain ers laboratory glass and anesthetic accessories Critical items such as invasive surgical instruments and anesthesia devices must be further processed by terminal sterilization before use any procedure The receptacles should be loaded in correct loading equipment recommended by Getinge Disinfection AB to comply with EN ISO 15888 The customer is responsible that Installation Qualification Operating Qualification and Performance Qualification are performed when EN ISO 15883 compliance is required KEY FEATURES Getinge 88 Series is standard WD equipped with proce
5. Cycle recording Cycle performance data can be printed or sent NetCom during the cycle and at cycle completion The cycle information includes cycle number cycle start date and time phase transition points disinfection quality and cycle alarms that occurred during the cycle NON RECIRCULATED VENTED DRYING SYSTEM Brushless Fan Motor Fresh air is pulled into the dryer unit by two powerful fans Unique brushless motor no carbon dust that can contaminate air filters and heating elements resulting in longer fan life and lower maintenance costs Drying Heater and HEPA Filter The fans force air through the electric heating elements at high velocity Drying air is quickly heated and filtered H14 HEPA filter before entering the chamber via the manifold pipe The hot air rapidly reaches all surfaces of the load through all spray arms This unige mode shortens the drying time Drying Heat Exchanger Hot air leaving the chamber passes through the heat exchanger in vanes touching the incoming fresh air Heat energy is transferred to the colder incoming air increasing its temperature before it reaches the heating element Warmed fresh air reduces the energy required to achieve maximum temperature Meanwhile the cool fresh air creates condensation in the moist hot air leaving the heat exchanger The condensa tion droplets are piped to the water and then to the drain Drying Sensor An optional dryi
6. E CONSTRUCTED OF MATERIALS UNLIKELY BE AFFECTED BY MOISTURE THIS INCLUDES BUT 15 NOT LIMITED TO CORROSION DUCTING SHALL BE SEALED TO PREVENT LEAKING AND CONSTRUCTED TO PERMIT DRAINAGE OF CONDENSATE WHEN NOT VENTING THE DRYING EXHAUST IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO ASSURE THE SPACE CAN HANDLE THE HOT VAPOR LADEN AIR FROM THE DRYING HEAT EXCHANGER PER NOTE 5 IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO COMPLETE ALL ELECTRICAL CONNECTIONS USING PROPERLY SIZED WIRING IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO PROVIDE A FUSED DISCONNECT SWITCH IN ALL ELECTRICAL SUPPLY LINES AT THE WASHER LOCATION AS REQUIRED BY LOCAL CODES IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO LEVEL THIS EQUIPMENT IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO PROVIDE NON SLIP FLOORING IN THE AREAS DEFINED AS APPROACH AREA PLAN VIEW OF THIS DRAWING IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO PROVIDE THE BARRIER WALL SEPARATING SOILED AND CLEAN AS REQUIRED MAXIMUM THICKNESS 15 5 1 4 133mm REMOTE DETERGENT CONTAINERS ARE TO BE WITHIN 60 1524mm OF THE UNIT AND ELEVATED NO MORE THAN 24 610mm ABOVE THE SUPPORTING FLOOR UNLESS AN ALTERNATE DISTRIBUTION SYSTEM WILL SUPPLY THE WASHERS IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO PROVIDE SHUTOFF VALVES FOR INCOMING HOT WATER COLD WATER PURIFIED WATER STEAM AND CONDENSATE OPTION THE VALVES ARE IN CLOSE PROXIMITY OF TH
7. E WASHER DISINFECTOR BELOW THE CEILING AND ACCESSIBLE TO SERVICE PERSONNEL CLEANING PERFORMANCE OF THIS PRODUCT IS BASED ON POTABLE WATER OF GOOD QUALITY THE QUALITY OF THE HOT AND COLD WATER SUPPLIES SHOULD BE CHECKED PRIOR TO INSTALLATION WHEN PURIFIED WATER IS USED FOR THE FINAL RINSE RESISTIMITY MUST BE BETWEEN 50 000 200 00 OHMS TO AVOID HARMFUL AFFECTS COMPRESSED AIR IS ONLY REQUIRED WHEN THE AUTO LOAD UNLOAD STATION IS CONFIGURED FOR THE WASHER AIR TO FREE OF AND WATER 11 Getinge USA Inc 1777 East Henrietta Road Rochester New York 14623 3133 USA Phone 800 475 9040 Fax 585 272 5033 info getingeusa com www getinge com GETINGE GETINGE GROUP www getinge com COMPLETE SOLUTIONS FOR INFECTION CONTROL Getinge is the world s leading provider of solutions for effective cleaning disinfection and sterilization in the healthcare and life science sectors We are dedicated to helping our customers provide better care at a lower cost We do this by offering well thought through and customized solutions This means that we are with our customers all the way from architectural planning and education to traceability and support with complete solutions long term commitment and global presence Getinge Always with you Getinge Canada Ltd 1575 South Gateway Road Unit C Mississauga Ontario L4W 5J1 Canada Phone 905 629 8777 info getingeusa com www getinge com
8. IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO ELIMINATE WATER HAMMER CONDITIONS SHOULD THEY OCCUR IN THE SERVICE PIPING IF REQUIRED SHOCK ARRESTORS OR PRESSURE REGULATORS WOULD BE PROVIDED AND INSTALLED THE CUSTOMER IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO PROVIDE A PROPERLY SIZED AND LOCATED DRAINAGE SYSTEM IN ACCORDANCE WITH THE UNIFORM PLUMBING CODE THE DRAIN LINE PROVIDED BY THE CUSTOMER MUST ACCOMMODATE A MINIMUM FLOW OF 25 GPM 90 I MIN CONSIDERATION SHOULD BE GIVEN TO OTHER EQUIPMENT DUMPING INTO DRAIN LINE PREVENT SLOW DRAINAGE BACK UP OR OVERFLOW WITHOUT DRAIN COOLING THE VOLUME 15 gt 13 GPM 50 MIN A TEMPERATURE UP 194 90 WITH DRAIN COOLING THE VOLUME IS gt 24 GPM 30 A TEMPERATURE UP TO 140 F 60 IT SHALL BE THE CUSTOMER S RESPONSIBILITY TO INSTALL THE WATER BACK FLOW PROTECTORS AND STRAINERS WHEN VENTING THE DRYING EXHAUST IT SHALL BE THE CUSTOMER S RESPONSIBIUTY TO PROVIDE A VENTING SYSTEM CAPABLE OF EXHAUSTING 206 CFM 350 m3 h MEASURED AT THE POINT OF CONNECTION TO THE WASHER THE VENTING SYSTEM SHALL HAVE AN AIR GAP OF AT LEAST 3 1 2 90mm DIRECTLY AFTER THE MACHINE EXHAUST IN ORDER TO CLEAR TOP SERVICE ACCESS OPENING THE DIAMETER OF THE VENTING SYSTEM EXHAUST HOOD WILL NOT EXCEED 06 MOTE THE HIGH WATER VAPOR CONTENT AND TEMPERATURE 194 F 9 OF THE EXHAUST MAY REQUIRE A SEPARATE DEDICATED EXHAUST DUCTING AND EXHAUST ARE B
9. MPERATURE CONSUMPTION RANGE PER REQUIREMENT CYCLE CONNECTION PIPE SIZE RANGE TO WASHER DYNAMIC 10 6 GAL PRE RINSE 40 LITERS 50 68 F 10 20 30 70 PSIG 8 10 200 482 kPa 30 40 3 4 20mm FEMALE HOT WATER 30 70 5 8 10 113 140 10 6 GAL WASH PHASE 200 482 kPa 30 40 1 45 60 40 LITERS 3 4 20mm FEMALE PURIFIED WATER 30 60 PSIG 10 GPM NOT TO EXCEED 8 5 GAL RINSE PHASE 200 415 kPa 30 40 MIN 140 F 6O 32 LITERS 3 4 20 MALE DRAIN 4 DRAIN PIPE 25 GPM WASTE LINE 38 47 GAL CYCLE 100mm 90 1 144 174 LITERS 3 75mm OUTLET EXHAUST 4 BUILDING VENT 206 222 CFM SEE NOTE 5 350 375 3 29 35 4 X 2 374 100 X 70mm s STEAM 3 4 NPT 43 72 PSIG 3 3 LB MIN 320 F MAX 33 49 5 LB CYCLE 20mm 300 500 kPa 1 5 160 15 22 5 1 2 13mm FEMALE c CONDENSATE RETURN 3 4 lt 5 PSI N A N A RECLAIMED 20mm 34 kPA BACK PRESSURE STEAM WATER 1 2 13mm FEMALE a COMPRESSED AIR SEE NOTE 15 3 8 10mm QUICK CONNECT 60 90 PSIG 7 CFM 400 620 WATER QUALITY NOTE 14 CONSUMPTION BASED ON INCOMING STEAM TEMPERATURE E ELECTRICAL RECOMMENDED SERVICE FULL LOAD AMPS DISCONNECT STEAM HEATED 240V SPH 60 2 C25 208 C30 ELECTRIC HEATED NOT AVAILA
10. Reset Alarms Start Cycle Program selection 1 6 The software has a memory for up to 60 programs However there are normally 10 30 standard programs installed Below the screen there are six programmable bottoms for the most common programs The other programs are reachable by entering the service menu Double door pass through units are provided with a small operating panel at the unload door Cycle status indicators Close Door Button ij GETINGE OPERATING PANEL ON SOIL SIDE CYCLE DESCRIPTION Prerinse The chamber is filled with cold water from the prefilled process tank The circulating pump is soft started and water is circulated through the spray system under full pump pressure Wash Cold or warm water fill the chamber from the prefilled process tank A peristaltic dosing pump automatically adds a programmed amount of chemical cleaning agent Once set point temperature has been achieved the controller will time the wash and then terminate the wash phase Filling and emptying is done via quick opening membrane valves in 15 seconds each Rinse Fresh hot water fills the chamber from the process tank Water is forced through the external heat exchanger into the spray manifold nozzles and onto the load Filling and emptying is done via quick opening membrane valves in 15 seconds each Final Rinse Disinfection Fresh water from the final rinse booster tank is pumped to the process tank and then fi
11. a separate stainless tank elevates the water temperature for final rinse disinfection water The water is pumped to the process tank before filling the chamber sump Jet Spray Washing Spray arms are fixed at the and bottom of the chamber Wash carts are equipped with spray arms under each shelf to allow water and detergent to reach all surfaces to be cleaned Carts with spray arms and injection wash carts automatically connect to water and drying air systems Automatic Chemical Dispensing Getinge 88 Series provides chemical dosing pumps with time volume base control Pulse based flow monitoring and control is standard Drain Tank Hot process solutions from the wash chamber are rapidly dumped to the drain tank via a large drain valve Drain Pump Wash and rinse solutions are pumped to the building waste system from the drain tank via the water trap Drain Cooling As hot solutions from drain tank and condensate from the heat exchanger enter the water trap cold water is automatically injected to reduce the temperature to 60 C 140F or less before the discharge enters the building waste system Process piping valves external heat exchanger steam coils manifold tubes sump base removable filter screens and chamber are made of AISI 316 stainless steel 316L stainless steel sanitary tri clamp fittings are used for easy removal of key process components Gaskets and hoses are EPDM PTFE or Silicone
12. delivery includes 1 set of the following docu mentation User Manual service Manual Installation Manual Standard Spare List e Quality Inspection Certificate Test temperature diagram Declaration of Conformity The documentation is supplied as paper copy apart from Standard Spare Part List and Service Manual which are supplied in CD format REV D DISCLAMIER Do not use this product specification for installation of equipment Subject to change without notice Advisory Note Getinge 88 Series Washer Disinfectors perform critical cleaning and microbial reduction step in the processing of soiled reusable medical devices Medical devices that will be used in sterile areas of the human body or will be contacting compromised tissues must be terminally sterilized before each subsequent use in a human patient STANDARD DESIGN FEATURES VIP Glass Doors VIP View in process Glass doors provide a full size viewing inside the chamber The door consist of two layers of safety tempered glass which provides excellent sound and heat abatement as well as an extra measure of operator safety Double Door Pass Through Door interlocks assure integrity of barrier wall by allowing only one door to be open at any given time Fine and Gross Debris Filters One self cleaning fine debris filter is located at the chamber bottom to filter water before entering the drain Upon completion of the draining phase t
13. he filter is back flushed and cleaned of debris The gross debris filter is located on the top of the filter arrangement and 15 easily removable for manual cleaning Top or Bottom Mounted Filling Valves here are up to three water inlets on the top of the chamber Filling through top of chamber eliminates dead legs and provides the air break to protect potable water from cross contamination The utility connections can either be top or bottom mounted Process tank Hot and cold incoming process water will fill the Process tank before entering the wash chamber During a wash cycle the Process tank is always filled with water to be used in the next wash phase This method of filling the chamber reduces the time delay to fill from building supply High Volume Low Pressure Wash Solution from the sump is pressurized by a pump and sent through the heat exchanger before entering the upper and lower spray arms and cart docking systems The pump has a speed controlled motor Low speed 15 always kept during rinse phases This way of operation saves cycle time and consumption of utilities External Process Heat Exchanger Solutions from the wash pump are forced through a powerful external steam heat exchanger to rapidly elevate and maintain REV D CUSTOMER REFERENCE process water temperature at specified set point The heat exchanger is integrated in the manifold pipe Booster Tank A standard steam heat exchanger enclosed in
14. lls the chamber If chemical is required a pro grammed amount of liquid is automatically added Once set point temperature has been achieved the controller will time the thermal rinse Filling and emptying is done via quick opening membrane valves in 15 seconds each Drying After Final Rinse Disinfection the drying starts Once the set drying time has elapsed the cycle is com pleted and the door be opened With partial loads optional drying sensor will further reduce the drying time STANDARD SAFETY FEATURES Illuminated Chamber Wash chamber is equipped with one 1 halogen lamp mounted through the ceiling to illuminate the chamber for safe operations Door Obstruction If the moving door contacts obstruction while the washer is closing the door the door will reverse and go back to open position The door can be closed again when the obstruction is removed Door Interlock Switches The PACS controls will permit only one door to be unsealed and open at any given time during normal operations Alternating door operation helps maintain integrity of the barrier wall Low Chemical Alarm Low level sensor in the wand will automatically send a low chemical alarm to the message screen to alert operators Controller allows one cycle to run with liquid in the lines Chemical container must be replaced or re filled before controller will allow subsequent cycles to be run GETINGE 88 SERIES OUTER DIMENSIONS IN MM
15. ng sensor installed in the drying pipe controls the humidity of the drying air The result is shorter drying times for partial loads Non Recirculated Drying Air accordance with Eu ropean standards to reduce risk of cross contamination hot chamber air is not recirculated over the load CONTROL SYSTEM PACS 350 Microcomputer Controls The PACS 350 modular PLC control system is dedicated to the control operation and maintenance of Getinge sterilizers and washer disinfectors featuring 8 MB RAM CPU processor with battery backup Digital inouts and outputs for machine control Analog measuring inputs Analog output for fan speed control 2x RS 232 COM port for serial communication 5 232 5 485 port for T DOC Process record connection 10 30 cycle program memory The PACS 350 controls all system functions monitors system operations both visually and audibly alerts the operator of cycle malfunction and on demand provides visual indication of the chamber temperature OPERATOR CONTROL PANEL The machine is controlled and operated from the control panel to the left of the soiled side door The panel interface is a durable LCD display with two rows with 20 character on each row A screen saver extends the life of the backlit LCD display Touching any key illuminates and reactivates the display Following indicators and function keys are located on the operator panel Process Running Process Complete Alarms
16. ost important quality criterion It must be the hallmark of all our external and internal commitments activities and products Products and service supplied by Getinge must conform to the agreed terms and expectations to ensure recommendations for further business The achievement of these quality goals is the basis for continued completive and successful enterprise CUSTOMER REFERENCE STANDARDS AND CODES Getinge 88 Series Washer Disinfectors complies with following standards and codes e MDD 93 42 Medical Device Directive Certificate 41314824 issued by Intertek Semko AB Code 0413 ETL SEMKO Testing Laboratories Inc Standard IEC 61010 1 EN 61010 1 61010 2 040 UL 61010A 1 CAN CSA C22 2 No 1010 1 92 e EMC Electromagnetic Compatibility Product Standard 61326 1 Product Family Standard EN IEC 60601 1 2 2004 DVGW Deutscher Verein des Gas und Wasserfaches EV Standard DVGW W 507 e Microbiological test Standard SPRI Specification 74203 EN ISO 15883 ORDERING INFORMATION PRODUCT SELECTION FOR ORDERING For ordering tick in your selections Q Standard choice Optional choice CONFIGURATION Double door with window automatic HEATING Q washer and booster heating with floor connection of steam Electrical dryer heating SUPPLY VOLTAGE Steam Heated Washer On the steam heated models the water heating elements in booster tank and circulation system are heated by facility
17. ss tank booster tank and drain tank e Short process time is achieved by utilizing large quick opening valves between the process tanks and the circulation Sump Cleansable spray arms are located at the and bottom of the chamber Wash carts are equipped with cleansable spray arms between each shelf to allow water to reach all surfaces to be cleaned wash carts automatically connect to water and drying air in order to clean and dry the inside of tubular items e The drying air is pre heated in a unique heat exchanger which also is a condensor for the outgoing air This energy saving process means REV D GETINGE GETINGE GROUP shorter drying times and reduced energy consumption e The Getinge 88 Series is standard equipped with independent temperature monitoring and validation test port according to EN ISO 15883 e Ciruclating water pressure monitoring is a standard feature e Data interface RS232 RS485 are standard as well as differential pressure monitoring of HEPA filter for drying All electrical components are easily accessibly within a pull out cabinet e Getinge 88 Series has a built in self cleaning debris filter e Automatic drying sensor adjust drying time on humidity thus reducing cycle time and energy consumption e Getinge 88 Series can be equipped with audible alarm that alerts operators if error code occurs QUALITY STATEMENT Confidence in the Getinge Group Is the m
18. steam The dryer is always electrically heated Q 240 V 3 PE 60 Hz Q 208 V 3 PE 60 Hz WATER VALVES AND CONNECTIONS Q Cold warm purified water connection with valves DOSING PUMPS As standard three dosing pumps for process chemicals are supplied All pumps are fitted with flow monitoring Dosing pump 3 for instrument lubricant Q Dosing pump 3 for enzyme wash PREPARATION FOR AUTOMATIC LOADING EQUIPMENT Getinge 88 Series is designed for manual or automatic loading unloading When using automatic loading un loading the washer needs to be prepared with interfaces to the loading unloading systems Q No automatic loading AGS Loading station only Unloading station only Loading amp unloading station OO ADDITIONAL OPTIONS Built in printer soiled side Built in printer clean side LANGUAGE Operator displays and manuals are available in a selec tion of languages Other information and manuals are in English Documentation are available for all EU languages except for Greek Please state wanted language below Other documentations and manuals are in English French German or Swedish WASH CARTS The Getinge 88 Series is very flexible when it comes to the varity of items to be cleaned and disinfected For most purposes standard wash carts are available For more detailed information we refer to catalogue Loading Equipment Getinge Washer Disinfector DOCUMENTATION Machine
Download Pdf Manuals
Related Search